• owner's manual • frequently asked questions • assembly instructions • warranty information t t t tuuuuccccssssoooonnnn w w w wooooooood d d deeeennnn s s s sw w w wiiiinnnngggg s s s seeeetttt m m m mooood d d deeeellll:::: # # # #6 6 6 65 5 5 54 4 4 411111111 manufacturer: backyard discovery 3001...
Please have the following information when you make your call: 1 – model number of the product located on the front of the assembly manual 2 – desription of the part from the parts list por favor tenga visible la siguiente informaciÓn cuando llame: 1 - nÚmero de modelo del producto que se encuentra ...
Owner’s manual play set rev5/20/10 brs dear customer: please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age . Structures are not intended for public use. The company does not warranty any of its residential stru...
Owner’s manual play set rev5/20/10 brs please refer to the assembly section of the assembly manual for maximum fall height . Positioning your playcenter 1. The playcenter is designed to be installed on a level surface by an adult with an adult helper . Place in a flat area of your yard to minimize g...
Owner’s manual play set rev5/20/10 brs the following chart explains the fall height in feet from which a life threatening head injury would not be expected critical heights in feet (m) of tested materials material uncompressed depth compressed depth 6" (152mm) 9" (228mm) 12" (304mm) to 9" (228mm) wo...
Owner’s manual play set rev5/20/10 brs 16. Instruct children to never crawl or walk across the top of monkey bars. 17. Instruct children to never crawl on top of a fort roof. 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on...
Owner’s manual play set rev5/20/10 brs disposal instructions: when the playcenter use is no longer desired, it should be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the unit is discarded. Third party assembly: customer may, in their sole discretion,...
Owner’s manual play set rev5/20/10 brs appendix a information on playground surfacing materials: the following information is from the united states consumer product safety commission’s information sheet for playground surfacing material; also see the following website for additional information: ww...
Rev5/20/10 brs play set assembly manual faqs: 1. Does the area for the playset need to be level? Yes. Backyard discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size are...
Rev5/20/10 brs www.Swingsetsonline.Com/support.Aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from backyard discovery’s website: www.Swing...
(tape measure) (claw hammer) (cordless drill or electric drill) (an adult w/ an adult helper) (rubber mallet - optional) (ladder) (phillips screw driver) (drill attachments: phillips head) (1/8" & 3/8" drill bits) tools required for installation: (these are the tools that are generally required for ...
B b b baaaassssiiiicccc s s s seeeettttuuuupppp d d d diiiim m m meeeennnnssssiiiioooonnnnssss place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. Safe play zone safe play ...
Parts identification wood components (not to scale) e1 - fort upright - w101519 1 3/8"x3 3/8"x89 1/2" (36x86x2273) (2) e2 - fort upright - w101520 1 3/8"x3 3/8"x89 1/2" (36x86x2273) (2) e77 - angle brace - w100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (2) f1 - angle brace - w101630 1 3/8"x2 3/8"x18 1/8...
Parts identification wood components (not to scale) h5 - picnic tarp support - w101542 1"x3 3/8"x24 1/2" (24x86x622) (2) h6 - wall slat - w101535 1"x3 3/8"x25 1/2" (24x86x648) (2) h7 - picnic support - w101625 1"x3 3/8"x15 1/4" (24x86x387) (2) h8 - picnic support - w101628 1"x3 3/8"x13 1/2" (24x86x3...
Parts identification wood components (not to scale) k2 - arched wall rail - w101531 5/8"x5 1/4"x34 7/8" (16x134x887) (1) k3 - arched wall rail - w101530 5/8"x5 1/4"x34 1/8" (16x134x868) (1) k4 - wall rail - w101533 5/8"x5 1/4"x34 1/8" (16x134x868) (1) m1 - tarp support - w101540 5/8"x3 3/8"x40" (16x...
Parts identification wood components (not to scale) m8 - picnic cleat - w101632 5/8"x3 3/8"x10 1/8" (16x86x258) (1) m9 - picnic cleat - w101633 5/8"x3 3/8"x6 3/4" (16x86x172) (1) m10 - wall rail - w101621 5/8"x3 3/8"x6 1/4" (16x86x160) (2) m11 - wall rail - w101527 5/8"x3 3/8"x4 3/4" (16x86x122) (2)...
Parts identification hardware aj - bolt hex 5/16x1-1/4 - h100042 (4) an - bolt hex 5/16x2-3/4 - h100047 (2) z - lag screw wh 5/16x2 - h100027 (42) bg - t-nut 5/16 - h100074 (7) bf - t-nut 3/8 - h100073 (7) f - bolt wh 5/16x1 - h100008 (4) a - bolt fa 3/8x1-1/2 - h100001 (7) h - bolt wh 5/16x1-1/2 - ...
Parts identification hardware br - screw pfh 8x1-1/8" - h100088 (48) bq - screw pfh 8x1-1/4" - h100087 (48) bp - screw pfh 8x1-1/2" - h100086 (42) bs - screw pfh 8x1-3/4" - h100089 (9) bw - screw pfh 8x3 - h100092 (26) bt - screw pfh 8x2-1/2 - h100090 (4) cb - washer safety 17x30 - h100103 (7) cj - ...
Parts identification a a a acccccccceeeessssssssoooorrrriiiieeeessss (not to scale) ek - slide rail 8' green right - a100054 (1) el - slide rail 8' green left - a100055 (1) ea - hand grip yellow plastic - a100043 (2) kf - trapeze with hardware yellow - a100109 (1) em - slide bed 8' yellow - a100056 ...
Parts identification a a a ac c c cc c c ce e e es s s ss s s so o o or r r riiiie e e es s s s (not to scale) kd - plastic ground stake brown - a100179 (6) kb - picnic table tarp - a100195 (1) kc - roof tarp - a100196 (1) - t-40 torx wrench - a100041 2 - t-40 torx bit - a100042 2 - t-30 torx bit - ...
Qty description 1 slide brace 3 bolt wh 5/16x1/2 3 nut barrel wh 5/16x5/8 3 washer lock ext 12x19 1 slide bed 8' yellow 3 5/8 8 5/8 13 5/8 1 nut barrel wh 5/16x5/8 washer lock ext 12x19 slide brace bolt wh 5/16x1/2 slide bed 8' yellow 8 foot slide assembly phase 1 phase notes ● drill 3 holes at one ...
Qty description 2 center slide brace 24 screw pfh 8x3 1 slide rail 8' green right 1 slide rail 8' green left slide rail 8' green left slide rail 8' green right center slide brace 8 foot slide assembly phase 2 phase notes ● place 1 slide rail on a flat surface and begin inserting slide bed at the bot...
Step 1 attach (2) qz triangle plates to sb74 swing beam using 1-3/4" bolts, lock washers and 7/8" barrel nuts. Attach (2) gd l brackets to sb74 swing beam using 2-3/4" hex bolts, flat washers and 5/16" lock nuts. Sb74 qz gd gd swing beam assembly sb74 - swing beam - w102304 2"x5 1/4"x89 1/2" (50x134...
Swing beam assembly step 2 insert (2) 2-1/2" bolts, lock washers and 1-1/2" barrel nuts into top edge of w71 swing beam support, as shown. Attach e77 angle braces to w71 swing beam support using 4- 1/2" bolts, lock washers and 7/8" barrel nuts. Attach h79 end support to e77 a ngle braces using 2" bo...
Step 3 attach (2) qz triangle plates to w71 swing beam support using 1-3/4" bolts, lock washer and 7/8" barrel nut. Bolt wh 5/16x1-3/4 washer lock ext 12x19 nut barrel wh 5/16x7/8 swing beam assembly sb74 w71 sb74 w71 qz.
Step 4 insert swing hanger quick link and safety washer into holes in the edge of sb74 swing beam. Secure swing hanger to w71 swing beam using flat washers and 5/16" lock nuts. Swing hanger quick link nut lock 5/16 washer flat 8x27 swing beam assembly sb74 sb74 washer safety 17x30
4' rock ladder phase 1 phase notes • assemble slats to rails as shown. • note oreintation of slats, be sure to arrange as shown. • see drawing below for slat spacing on rails. • using slats as a guide, pre-drill top edges of rails with a 1/8" drill bit. Failure to pre-drill may result in board split...
4' rock ladder phase 2 & 3 p p p ph h h ha a a as s s se e e e n n n no o o ot tt te e e es s s s • oreint top edge of rocks with top edge of slats. • fasten rocks as shown. Bolt fa 3/8x1-1/2 climbing rock green small t-nut 3/8 screw pfh 8x1-1/8 qty. Description 6 climbing rock green small 6 bolt fa...
Fort assembly phase 1 phase notes • assemble with hardware as shown. • for ease during assembly, assemble uprights flat on the ground. Hardware needed: • (14) d - nut barrel wh 5/16x7/8 - h100005 • (14) ad - washer lock ext 12x19 - h100031 • (16) ac - washer lock ext 8x19 - h100030 • (10) k - bolt w...
Fort assembly phase 2 phase notes • assemble with hardware as shown. Step 1: attach 'h1' roof cross brace to 'e1' fort uprights using hardware 'k', 'ac', 'ad', & 'd' as shown. Parts needed: • (1) h1 - roof cross brace - w101538 • (2) e1 - fort upright - w101519 • (1) k3 - arched wall rail - w101530 ...
Phase notes • assemble with hardware as shown. Parts needed: • (2) m3 - tarp support - w101539 • (1) m4 - floor/tarp support - w101541 • (3) k1 - wall rail - w101528 • (1) k2 - arched wall rail - w101531 • (2) m5 - wall rail - w101522 hardware needed: • (8) ck - screw pfh 8x2 - h100111 • (4) bp - sc...
Phase notes • assemble with hardware as shown. Fort assembly phase 4 step 1: attach 'h4' floor brace to 'm5' wall rails using screws 'bt', as shown. Parts needed: • (1) h4 - floor brace - w101631 • (2) h2 - floor joist - w101521 • (4) h10 - floor brace - w101534 • (2) f1 - angle brace - w101630 hard...
Fort assembly phase 5 phase notes • assemble with hardware as shown. Parts needed: • (2) m7 - floor board - w101524 • (8) m2 - floor board - w101525 hardware needed: • (40) ck - screw pfh 8x2 - h100111 • (20) bq - screw pfh 8x1-1/4 - h100087 step 1: gather the (2) 'm7' floor boards & (8) 'm2' floor ...
Fort assembly phase 6 phase notes • assemble with hardware as shown. Parts needed: • (2) m11 - wall rail - w101527 • (2) m10 - wall rail - w101621 • (1) m6 - wall rail - w101523 • (1) h2 - floor joist - w101521 hardware needed: • (2) k - bolt wh 5/16x2 - h100012 • (8) ac - washer lock ext 8x19 - h10...
Phase notes • assemble with hardware as shown. Parts needed: • (2) h6 - wall slat - w101535 • (2) ej - l bracket green - a100053 hardware needed: • (8) bq - screw pfh 8x1-1/4 - h100087 • (4) bl - screw tapping 14x3/4 - h100083 step 1: attach 'h6' wall slat to 'm11' wall rail using screws 'bq'. Secur...
Fort assembly phase 8 phase notes • assemble with hardware as shown. Parts needed: • (4) m12 - wall slat - a101536 hardware needed: • (8) br - screw pfh 8x1-1/8 - h100088 • (8) bq - screw pfh 8x1-1/4 - h100087 step 1: attach 'm12' wall slats to 'k4' wall rail using screws 'br', as shown. Note: due t...
Phase notes • assemble with hardware as shown. Parts needed: • (5) m12 - wall slat - w101536 • (2) j1 - wall slat - w101622 • (2) ej - l bracket green - a100053 step 1: attach 'm12' wall slats to 'k1' wall rail using screws 'br', as shown. Step 2: attach 'm12' wall slats to 'm6' wall rail using scre...
Phase notes • assemble with hardware as shown. Fort assembly phase 10 parts needed: • (2) h5 - picnic tarp support - w101542 • (1) m3 - tarp support - w101539 hardware needed: • (2) z - lag screw wh 5/16x2 - h100027 • (2) ac - washer lock ext8x19 - h100030 • (4) ck - screw pfh 8x2 - h100111 step 1: ...
Fort assembly phase 11 phase notes • assemble with hardware as shown. Hardware needed: • (2) bg - t-nut 5/16 - h100074 • (8) ac - washer lock ext 8x19 - h100030 • (2) l - bolt wh 5/16x2-1/4 - h100013 • (6) z - lag screw wh 5/16x2 - h100027 • (12) ck - screw pfh 8x2 - h100111 • (6) br - screw pfh 8x1...
Step 1: attach 'h7' picnic support to 'g1' ground board using "safe-t-fuse" hardware. Pre-drill & attach 'g3' picnic support to 'g1' ground board using screws 'bs', as shown. Phase notes • assemble with hardware as shown. Parts needed: • (2) h7 - picnic support - w101625 • (2) g3 - picnic support - ...
Step 1: attach 'm1' tarp support to 'k3' arched wall rail & 'h1' wall rail using "safe-t-fuse" hardware, as shown. Repeat step attaching 'm1' tarp support to 'k4' wall rail & 'h1' wall rail using "safe-t-fuse" hardware. Phase notes • assemble with hardware as shown. Parts needed: • (2) m1 - tarp sup...
Step 1: drape 'kc' tarp over 'm4' floor / tarp support and 'm3' tarp supports. Attach one side of tarp to the inside of 'm3' with (3) screws 'cy'. Pull other side of tarp tight and attach to the inside of other 'm3' tarp support using (3) screws 'cy', as shown. Phase notes • assemble with hardware a...
Phase notes • assemble with hardware as shown. Parts needed: • (1) kb - picnic table tarp - a100195 fort assembly phase 15 hardware needed: • (6) cy - screw pwh 8x5/8 - h100128 step 1: drape 'kb' tarp over 'm4' floor / tarp support and 'm3' tarp supports. Attach one side of tarp to the inside of 'm3...
Da step 1: attach 'ea' hand grip to 'h6' wall slat using screw 'az', washers 'cg' & 'ce', and t-nuts 'be', as shown. (the 'be' t-nuts must be inserted into 'h6' wall slat before assembly of hand grips.) repeat step to assembly second 'ea' handle grip. Phase notes • assemble with hardware as shown. P...
Step 1: using the diagram below, pilot drill using a 1/8" drill bit and attach the rock wall ladder to 'm5' wall rail using lag screws 'aa' & washers 'ac', as shown. Hardware needed: • (2) aa - lag screw wh 5/16x2-1/2 - h100028 • (2) ac - washer lock ext 8x19 - h100030 rock ladder attachment phase 1...
Phase notes • assemble with hardware as shown. Slide attachment phase 18 hardware needed: • (3) b - nut barrel wh 5/16x5/8 - h100004 • (3) ad - washer lock ext 12x19 - h100031 • (3) cm - bolt wh 5/16x1/2 - h100115 parts needed: • (1) slide assembly step 3: attach the slide assembly to the fort floor...
Swing beam attachment phase 19 phase notes • assemble with hardware as shown. Parts needed: • (1) swing beam assembly • (1) hc - backyard discovery id tag - a100164 hardware needed: • (4) bg - t-nut 5/16 - h100074 • (4) bx - washer split 5/16 - h100095 • (4) cd - washer flat 8x27 - h100105 • (4) aj ...
Anchoring instructions phase 20 phase notes • assemble with hardware as shown. • install the screw into the upright so that the tip of the screw does not stick through. Make sure you have enough wood to accommodate the screw before installing. • failure to use stakes can void warranty & cause injury...
Rev5/20/10 brs limited warranty this limited warranty by backyard discovery applies to products manufactured under the backyard discovery brand or its other brands including but not limited to backyard botanical, adventure playsets, and leisure time products. Backyard discovery warrants that this pr...