- DL manuals
- Bad Boy
- Lawn Mower
- Outlaw 6100
- Owner's, service & parts manual
Bad Boy Outlaw 6100 Owner's, service & parts manual
Summary of Outlaw 6100
Page 1
Zero-turn mower owner’s, service & parts manual for additional information, please see us at www.Badboymowers.Com bad boy, inc. 102 industrial drive batesville, arkansas 72501 ©2015 12-11 outlaw & outlaw extreme models.
Page 2: Table of Contents
Table of contents basic information ................................................................................................ Section 1 (page 4) bad boy safety guidelines ............................................................................. Section 2 (pages 5–8) operation ...............
Page 3
This manual applies to the following equipment: bad boy outlaw series bad boy outlaw extreme series outlaw 5400 54˝ 810cc vanguard outlaw extreme 5400 54˝ 824cc kohler efi outlaw 6100 61˝ 810cc vanguard outlaw extreme 6100 61˝ 824cc kohler efi outlaw 5400 54˝ 747cc kohler confidant outlaw extreme 54...
Page 4: Section 1:
Section 1: basic information congratulations on the purchase of your new bad boy mower! The purpose of this manual is to assist operators in maintaining and operating their machine. The information and instructions in this manual can help you attain years of performance from your new bad boy. Also, ...
Page 5: Section 2:
Section 2: mower safety guidelines never allow untrained people to operate this machine. It is the owner’s responsibility to get training and see to it that anyone who has permission to use your machine receives the proper training. Do not mow around people. The factory discharge chute is designed t...
Page 6: Slope Operation
Slope operation slopes are a major factor related to loss of control and tip over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope, or you feel uneasy on it, do not mow it. 2.22 mow up and down slopes, not across. ...
Page 7: Service:
Service: safe handling of gasoline to avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. 2.45 extinguish all cigarettes, cigars, pipes, and all other sources of ignition. 2.46 use only an approved gasoline co...
Page 8: Safety Interlock System
2.69 always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion. Welding can structurally weaken or deform the wheel. 2.70 park machine ...
Page 9: Section 3:
Section 3: mower operation never operate the machine with faulty equipment. Always be alert of sudden changes in landscape, as the mower will react differently on slopes or embankments than it will on flat surfaces. Never operate the mower with the discharge chute open. Do not cross terrain, other t...
Page 10: Section 4:
Section 4: mower maintenance first every 50 every 100 every daily 8 hours or hours or 250 section maintenance hours annually* annually* hours check and add engine oil ● section 3 section 2 ● (pump) 6 (deck) check condition of blades ● section 6 check for fule and oil leakage ● section 3 initial oil ...
Page 11
Page 11 performed: performed performed: performed performed performed: performed performed: performed performed performed: performed: performed performed performed performed performed: performed: performed: performed: performed: date: hours: date: hours: date: hours: date: hours: date: hours: date: ...
Page 12: Section 5:
Section 5: mower storage & transportation 5.1 keep machine from collecting debris by storing in a covered area while not in use. 5.2 fuel can harm your machine if left for more than 30 days without changing, especially if the fuel contains ethanol. Never use fuel with more than 10% ethanol by volume...
Page 13: Section 6:
Section 6: troubleshooting 6.1 q: how do i prevent an uneven cutting pattern and increase the quality of cut? 6.1 a: check tire pressure, check blade sharpness (replace blades or sharpen at least once per year or when needed), make sure blades are tightened properly, check spring and belt tension, c...
Page 14: Section 7:
Section 7: controls 7.1 ignition switch—bad boy mowers have a three position ignition switch: off, run, and start. With key inserted, rotate it clockwise to start position and release key when engine starts. Switch will automatically return to he run position. 7.2 throttle control—a cable is connect...
Page 15: Section 8:
Section 8: moving inoperable mower 8.1 do not tow machine. Use a winch to load on a trailer for transporting. 8.2 attention: return bypass valves to operating position before running mower following repairs. 8.3 if it becomes necessary to move an inoperable mower, the drive transaxles are equipped w...
Page 16: Section 10:
Section 10: mower blade maintenance 10.1 check mower blades after each use. This is essential for maintaining well-groomed turf. Keep the blades sharp. If a dull blade is used for cutting, the grass will tear rather than cut. This could damage the grass leaving a brown frayed top on the grass within...
Page 17
How to choose the right blade essentially there are only two basic styles of mowing blades used or approved for use on our current products: 1) the standard style of mowing blade is essentially designed for cutting grass and effectively discharging the clippings out from the deck to fall onto the la...
Page 18: Mowing Tips:
Mowing tips: • mow header strips at the ends of the lawn and around flower beds first. Make them wide enough that you can turn the mower around in the already mown section. Then mow back and forth between these header strips overlapping each lap by about 1/8 the width of the mower’s deck. • don’t cu...
Page 19: Service Section
Service section section 1: hydrostatic system page 19 the hydro reservoir tank on the outlaw model is located on each side of rear cover. Notice the “full cold” line at the bottom of the tank. Use only 20w-50 motor oil in this tank. Conventional or synthetic oil may be used. The following maintenace...
Page 20
Purging procedure due to the effects air has on the efficiency in hydrostatic drive applications, it is critical that the air is purged from the system. These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been...
Page 21
Changing your hydraulic oil and filter extreme 5400 1) place an oil drain pan (12” or more in diameter and 8 qt. Capacity is optimal) beneath the oil filter. Remove the oil filter cover from the transaxle to drain the oil. Remove the o-ring from the cover and discard the o-ring. 2) after the oil has...
Page 22
Page 22 under the rear of the mower, you will find the two levers shown in the image. These bypass levers serve as a neutral for moving the mower while the engine is not running. Pull the levers out and lock them into place to activate the bypass. When adjusting the tracking on the mower, the length...
Page 23: Section 2: Drive Belt
Section 2: drive belt page 23 shown on the right is the tensioner for your pump belt. Adjusting this will either increase or decrease tension on the belt. Use a ¾” wrench to loosen the jam nuts and either tighten for more belt tension or loosen for less belt tension. The belt tension should be set t...
Page 24: Section 3: Engine
Section 3: engine page 24 810cc vanguard this machine has an oil drain hose installed on the engine to allow for easier oil changes. Bad boy recommends that the oil and filter be changed at intervals of 50 usage hours or yearly, whichever occurs first. The oil capacity is 2 quarts. Bad boy 10w-30 sy...
Page 25
The fuel filter is located in the fuel line about 12˝ from the carburetor on the side of the engine. Replace the filter yearly. Prior to the removal of the old filter, note the direction of fuel flow as indicated on the filter. Have towels readily available in order to quickly remove any fuel leakag...
Page 26
3.4 changing the spark plugs and checking the spark plug gap: 1) remove the wire on the spark plug and use a 5/8” socket to remove the spark plug. 2) check the gap on the spark plug to verify that it is 0.03 in using a feeler gauge. 3) if the spark plug is worn, overheated, wet or carbon fouled repl...
Page 27
Kohler confidant 747cc this machine has an oil drain hose installed on the engine to allow for easier oil changes. Bad boy recommends that the oil and filter be changed at intervals of 50 usage hours or yearly, whichever occurs first. The oil capacity is 2 quarts. Bad boy 10w-30 synthetic blend engi...
Page 28
The fuel filter is located in the fuel line about 12˝ from the carburetor on the side of the engine. Replace the filter yearly. Prior to the removal of the old filter, note the direction of fuel flow as indicated on the filter. Have towels readily available in order to quickly remove any fuel leakag...
Page 29
The air cleaner is the engine’s only defense against damaging foreign particles. It is very important that the air cleaner element is inspected prior to each use. Remove the element and tap its sides in order to remove debris. Do not blow the filter out using compressed air. Doing so will greatly re...
Page 30
3.4 changing the spark plugs and checking the spark plug gap: 1) remove the wire on the spark plug and use a 5/8” socket to remove the spark plug. 2) check the gap on the spark plug to verify that it is 0.03 in using a feeler gauge. 3) if the spark plug is worn, overheated, wet or carbon fouled repl...
Page 31: Kawasaki Fx730V
Kawasaki fx730v this machine has an oil drain hose installed on the engine to allow for easier oil changes. Bad boy recommends that the oil and filter be changed at intervals of 50 usage hours or yearly, whichever occurs first. The oil capacity is 2 quarts. Bad boy 10w-30 synthetic blend engine oil ...
Page 32
The fuel filter is located in the fuel line on the left side of the engine by the starter motor. Replace the filter yearly. Prior to the removal of the old filter, note the direction of fuel flow as indicated on the filter. Have towels readily available in order to quickly remove any fuel leakage. A...
Page 33
3.4 changing the spark plugs and checking the spark plug gap: 1) remove the wire on the spark plug and use a 13/16” socket to remove the spark plug. 2) check the gap on the spark plug to verify that it is 0.03 in using a feeler gauge. 3) if the spark plug is worn, overheated, wet or carbon fouled re...
Page 34: Engines
Engines kohler command pro efi ecv870 this machine has an oil drain hose installed on the engine to allow for easier oil changes. Bad boy recommends that the oil and filter be changed at intervals of 50 usage hours or yearly, whichever occurs first. The oil capacity is 2 quarts. Bad boy 10w-30 synth...
Page 35
The fuel filter is located in the fuel line about 12˝ from the carburetor on the side of the engine. Replace the filter yearly. Prior to the removal of the old filter, note the direction of fuel flow as indicated on the filter. Have towels readily available in order to quickly remove any fuel leakag...
Page 36
The air cleaner is the engine’s only defense against damaging foreign particles. It is very important that the air cleaner element is inspected prior to each use. Remove the element and tap its sides in order to remove debris. Do not blow the filter out using compressed air. Doing so will greatly re...
Page 37
3.4 changing the spark plugs and checking the spark plug gap: 1) remove the wire on the spark plug and use a 5/8” socket to remove the spark plug. 2) check the gap on the spark plug to verify that it is 0.03 in using a feeler gauge. 3) if the spark plug is worn, overheated, wet or carbon fouled repl...
Page 38: Kawasaki Fx850V
Kawasaki fx850v this machine has an oil drain hose installed on the engine to allow for easier oil changes. Bad boy recommends that the oil and filter be changed at intervals of 50 usage hours or yearly, whichever occurs first. The oil capacity is 2 quarts. Bad boy 10w-30 synthetic blend engine oil ...
Page 39
The fuel filter is located in the fuel line on the left side of the engine by the starter motor. Replace the filter yearly. Prior to the removal of the old filter, note the direction of fuel flow as indicated on the filter. Have towels readily available in order to quickly remove any fuel leakage. A...
Page 40
3.4 changing the spark plugs and checking the spark plug gap: 1) remove the wire on the spark plug and use a 13/16” socket to remove the spark plug. 2) check the gap on the spark plug to verify that it is 0.03 in using a feeler gauge. 3) if the spark plug is worn, overheated, wet or carbon fouled re...
Page 41: 993Cc Vanguard
993cc vanguard this machine has an oil drain hose installed on the engine to allow for easier oil changes. Bad boy recommends that the oil and filter be changed at intervals of 50 usage hours or yearly, whichever occurs first. The oil capacity is 2 quarts. Bad boy 10w-30 synthetic blend engine oil i...
Page 42
The fuel filter is located in the fuel line about 12˝ from the carburetor on the side of the engine. Replace the filter yearly. Prior to the removal of the old filter, note the direction of fuel flow as indicated on the filter. Have towels readily available in order to quickly remove any fuel leakag...
Page 43
The air cleaner is the engine’s only defense against damaging foreign particles. It is very important that the air cleaner element is inspected prior to each use. Remove the element and tap its sides in order to remove debris. Do not blow the filter out using compressed air. Doing so will greatly re...
Page 44
3.4 changing the spark plugs and checking the spark plug gap: 1) remove the wire on the spark plug and use a 5/8” socket to remove the spark plug. 2) check the gap on the spark plug to verify that it is 0.03 in using a feeler gauge. 3) if the spark plug is worn, overheated, wet or carbon fouled repl...
Page 45: Section 4: Electrical System
Section 4: electrical system page 45 this mower is equipped with one protective fuse: a 30 amp main fuse (pictured to the right). A blown fuse usually indicates a problem within the electrical system or an electrical component. Ensure the battery terminals are tightly fastened. Never replace a fuse ...
Page 46
Page 46.
Page 47: Section 5: Frame
Section 5: frame page 47 the front fork nuts require a torque of 40ft-lbs. While applying this torque, turn the fork itself to ensure no damage is done to the bearing. This operation is only necessary if a repair requires it. Torque rear wheel lugs to 65-75 ft. Lbs. Re-torque at every oil change and...
Page 48
The pump belt tensioner is located under the engine and has a grease fitting at its pivot point. Grease at every engine oil change. The deck belt tensioner is located at the rear of the deck and has a grease fitting on its pivot point. Grease at every engine oil change. The control arm blocks have g...
Page 49: Section 6: Cutting Deck
Section 6: cutting deck page 49 deck belt removal 1) remove ignition key. 2) raise the deck to its highest position. 3) remove the right pulley cover. 4) while lifting up on the belt (as shown in the photograph), rotate the pulley until the belt is free of the pulley. Exercise caution while performi...
Page 50
Page 50 1) start on a flat level surface and set the air pressure in all four tires to 12 psi. 2) get 2 2x4s and make sure that the wider sides are similar length. 3) take off the foot pedal and raise the floor plate. 4) lower the deck onto the 2x4s and pin the deck into its top available height. Re...
Page 51
The deck spring tension is critical. If the tension is too high, premature failure of the deck belt and blade spindles can occur. If the tension is too low, the belt can ‘jump off’ or slip on the pulleys. This results in reduced cut quality and early belt failure. Spring tension adjustments can be m...
Page 52
Blade removal: to change blades, it may be easier to use a piece of wood to keep the blade from turning so that the bolt can be loosened. Use a 15/16” socket and impact drill, or a wrench and an extension to gain more leverage. You might need to put a ¾” wrench on top of the pulley bolt to keep the ...
Page 53: Parts Section
Parts section page 53 parts list description part number qty item front fork 023-7913-00 1 1 seal 012-7003-00 1 2 1/2-13 nylon flange nut 013-8050-00 1 3 1/2" x 9" gr 5 hex bolt 018-7010-00 1 4 dust cover 014-7005-00 1 5 bearing 010-7001-00 2 6 front wheel spanner 025-5202-00 1 7 1 3/8" wheel bearin...
Page 54
Page 54 10 13 11 23 15 15 26 4 7 6 19 3 1 3 5 8 9 33 8 35 8 28 16 9 22 17 18 21 18 17 27 20 34 14 12 26 24 25 outlaw drive arms welded to frame 30 31 2 29 32 2 3 1 3 31.
Page 55
Page 55 parts list description part number qty item drive lever spring 034-8025-00 4 1 bushing for 2012 drive arms 032-5055-00 4 2 .515 id nylon shoulder washer 019-8027-00 8 3 1/4" press in grease fitting 024-6034-00 2 4 1/2-13 nylon flange nut 013-8050-00 2 5 5/16" nut 013-8043-00 2 6 5/16" x 3/4"...
Page 56
Page 56 detail a detail b a b 29 35 18 33 7 8 9 6 3 2 12 1 19 34 20 10 23 24 22 21 4 5 27 28 25 32 31 26 30 15 17 16 17 14 14 13 7 8 9 13 14 outlaw gas tank assemblies 11 36 34 17 16 37.
Page 57
Page 57 parts list description part number qty item 2016 outlaw seat bracket 080-5116-00 1 1 5/16-18 x 1 carriage bolts zinc 018-8065-00 4 2 .360 id plastic washer 019-6042-00 4 3 3/8" nylock flange nut 013-5202-00 2 4 3/8" x 1 1/4" carriage bolt 018-5043-00 2 5 5/16-18 nylon insert flange nut zinc ...
Page 58
Page 58 detail a a 21 13 12 14 15 19 19 19 30 20 22 18 14 13 17 16 23 6 5 25 2 24 3 4 2 8 9 7 1 3 10 11 2 26 27 28 29 31.
Page 59
Page 59 parts list description part number qty item 2015 standard/extreme outlaw frame 070-5370-00 1 1 5/16" nylock flange nut zinc 013-8049-00 7 2 5/16" x 1" carriage bolt 018-8065-00 6 3 .360 id plastic washer 019-6042-00 2 4 #10 x 1/2" self tapping screw 030-3050-00 6 5 button bumper 029-4010-00 ...
Page 60
Page 60 detail a detail b detail c outlaw a b c 43 41 38 39 40 42 33 32 43 35 36 34 37 54 1 19 27 25 23 22 24 21 20 28 26 58 5 10 9 8 11 2 3 44 24 47 31 45 5 6 7 30 55 29 49 50 13 14 12 18 15 16 17 4 46 20 28 detail c outlaw extreme 26 57 53 56 21 24 23 52 25 51 31 48.
Page 61
Page 61 parts list description part number qty item 2015 standard/extreme outlaw frame 070-5370-00 1 1 2015 outlaw act bar assembly (front) 028-6030-00 1 2 2015 outlaw act bar assembly (rear) 028-6040-00 1 3 outlaw deck linkage rod 028-6050-00 1 4 1/2-13 nylon flange nut 013-8050-00 10 5 bushing- sf...
Page 62
Page 62 detail b detail c b c 10 54 12 11 9 5 4 9 7 6 41 32 34 32 42 45 9 4 4 9 14 33 44 37 25 38 35 36 19 64 20 16 53 23 22 1 39 9 5 4 18 43 25 6 6 21 17 16 14 15 28 31 30 27 26 14 17 15 16 21 6 2 8 3 29 40 13 25 24 6 25 46 47 50 52 9 51 5 4 48 49 59 56 61 58 60 55 57 62 63.
Page 63
Page 63 parts list description part number qty item 2016 outlaw seat bracket 080-5116-00 1 1 outlaw cooler cover 014-2100-00 1 2 2016 seat plate outlaw 026-2016-00 1 3 5/16-18 x 1 carriage bolts zinc 018-8065-00 10 4 .360 id plastic washer 019-6042-00 8 5 3/8" nylock flange nut 013-5202-00 10 6 3/8"...
Page 64
Page 64 parts list description part number qty item outlaw transaxle cross brace 203-0100-00 1 1 1/2" x 1 1/2" hex bolt 018-5006-00 4 2 zt - 5400 - left (extreme only) 050-7000-00 1 3 1/2" x 1" hex bolt 018-2030-00 4 4 zt - 5400 - right (extreme only) 050-7001-00 1 5 acorn lug nut 013-3000-00 10 6 2...
Page 65
Page 65 parts list description part number qty item fx-730v 015-0730-00 1 1 1/4 x 2 square key stock 042-5020-00 1 2 4 3/4 motor pulley 033-5035-00 1 3 clutch assembly 070-1000-00 1 4 7/16" x 2 1/2" hex bolt 018-5300-00 1 5 7/16" lock washer 019-8053-00 1 6 clutch pigtail 070-2000-00 1 7 oil drain 0...
Page 66
Page 66 parts list description part number qty item 4 3/4 motor pulley 033-5035-00 1 1 3/8 x 1 1/8 bolt 018-1075-00 4 2 1/4 x 2 square key stock 042-5020-00 1 3 exhaust gasket 015-2751-00 2 4 oil drain valve 015-5401-00 1 5 5/16-18 x 3/4 socket c/s 018-8067-00 4 6 5/16 set screw 030-0050-00 1 7 grou...
Page 67
Page 67 parts list description part number qty item 824cc efi kohler 015-0824-00 1 1 1/4 x 2 square key stock 042-5020-00 1 2 3/8" set screw 030-6029-00 1 3 oil drain hose 051-5401-00 1 4 4 3/4 motor pulley 033-5035-00 1 5 1 1/8" flat spacer 019-6029-00 1 6 7/16" lock washer 019-8053-00 1 7 7/16" x ...
Page 68
Page 68 parts list description part number qty item 810 vanguard 015-0810-00 1 1 3/8" set screw 030-6029-00 1 2 4 3/4 motor pulley 033-5035-00 1 3 3/8 x 1 1/8 bolt 018-1075-00 3 4 ground cable 086-0005-00 1 5 5/16" x 1 3/4" hex bolt 018-8059-00 1 6 5/16" nut 013-8043-00 1 7 5/16" lock washer 019-805...
Page 69
Page 69 parts list description part number qty item kawasaki engine fx-850-v-cs09r 015-0031-00 1 1 4 3/4 motor pulley 033-5035-00 1 2 pump belt 041-5048-00 1 3 3/8" set screw 030-6029-00 1 4 1/4 x 2 square key stock 042-5020-00 1 5 3/8 x 1 1/8 bolt 018-1075-00 4 6 oil drain 015-5404-00 1 7 black boo...
Page 70
Page 70 993cc vanguard description part number qty item 1/4" x 1" key 042-6030-00 1 1 5/16 set screw 030-0050-00 1 2 ground cable 086-0005-00 1 3 5/16" lock washer 019-8051-00 1 4 5/16" nut 013-8043-00 1 5 black boot for ground cable 103-5400-00 1 6 5/16" x 1 3/4" hex bolt 018-8059-00 1 7 3/8 x 1 1/...
Page 71
Page 71 detail a detail b detail c detail d a b c d 4 43 41 42 44 49 8 4 52 7 47 4 59 58 58 32 57 61 63 56 60 16 15 35 34 45 13 12 20 18 17 28 24 23 46 26 25 27 22 26 2 3 21 37 30 4 29 14 1 5 31 54 4 5 4 51 50 47 9 10 11 38 39 40 36 6 54 33 19 55 outlaw 54" deck 53 48 62 28.
Page 72
Page 72 parts list description part number qty item 2015 54" deck 060-5550-00 1 1 3/8" x 3/4" hex bolt 018-5250-00 3 2 3/8" flange nut 013-5201-00 3 3 1/2-13 nylon flange nut 013-8050-00 30 4 1/2 x 3 1/2 flange bolt grade 8 018-2018-00 3 5 .502 id x .750 od x 1.500 long spacer 025-5338-00 2 6 1/2 x ...
Page 73
Page 73 detail a detail b detail c detail d a b c d 8 50 7 53 4 42 45 43 44 4 4 58 57 48 60 57 33 56 63 55 59 14 4 30 31 38 1 37 26 27 3 22 2 28 23 24 25 29 47 5 32 61 4 5 6 61 9 10 11 4 52 51 40 41 39 17 20 34 19 18 12 13 21 46 36 35 15 16 54 outlaw 61" deck 48 49 62 29.
Page 74
Page 74 parts list description part number qty item 2015 61" deck 060-6150-00 1 1 3/8" x 3/4" hex bolt 018-5250-00 3 2 3/8" flange nut 013-5201-00 3 3 1/2-13 nylon flange nut 013-8050-00 32 4 1/2 x 3 1/2 flange bolt grade 8 018-2018-00 3 5 .502 id x .750 od x 1.500 long spacer 025-5338-00 2 6 1/2 x ...
Page 75
Page 75 detail a 56 detail b detail c detail d a b c d 33 30 29 28 32 27 12 18 31 11 45 4 36 62 4 5 3 62 10 9 8 3 2 46 50 39 38 15 3 17 16 34 35 1 20 19 21 61 44 26 13 14 24 23 22 25 6 52 3 3 48 7 41 3 42 40 43 3 58 57 46 57 37 60 64 55 59 54 49 outlaw 72" deck 51 53 47 63 33.
Page 76
Page 76 parts list description part number qty item 2015 72" deck 060-7250-00 1 1 5-3/4 idler pulley-don dye 033-7201-00 1 2 1/2-13 nylon flange nut 013-8050-00 32 3 1/2 x 3 1/2 flange bolt grade 8 018-2018-00 3 4 .502 id x .750 od x 1.500 long spacer 025-5338-00 2 5 1/2 x 2" carriage bolt 018-1050-...
Page 77
Page 77 parts list description part number qty item 4000 series spindle housing 037-4001-00 1 1 4000 series spindle spacer 037-4002-00 1 2 locking collar w/ 1/4"-20 set screw 037-9050-00 1 3 spindle dust cap 037-8002-00 2 4 zt-aos spindle shaft 037-6026-00 1 5 bearing - 6206 037-6023-00 4 6 5 4 6 6 ...
Page 78: 2016 Limited Warranty
2016 limited warranty for bad boy commercial mower ( stand on, diesel, outlaw, outlaw extreme, and outlawxp) 1. What this warranty covers, and for how long: bad boy, inc. Will, at its option, repair or replace, without charge, any part covered by the warranty which is found to be defective in materi...
Page 79: Warranty Registration
Bad boy, inc. 102 industrial drive batesville, ar 72501 www.Badboymowers.Com technical support: ............................................................Techsupport@badboymowers.Com warranty: .....................................................................................Warranty@badboymower...
Page 80: Www.Badboymowers.Com
For additional information, please see us at www.Badboymowers.Com bad boy, inc. 102 industrial drive batesville, arkansas 72501.