- DL manuals
- Badger Meter
- Transmitter
- ORION SE
- Installation & Operation Manual
Badger Meter ORION SE Installation & Operation Manual
Summary of ORION SE
Page 1
Orion® se network gateway transceiver installation & operation manual ori-iom-60-en (june 2012) 62014-146 rev. 3.
Page 2
Orion® se network gateway transceiver page ii june 2012.
Page 3: Contents
Installation & operation manual contents overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 lice...
Page 4
Orion® se network gateway transceiver page iv june 2012.
Page 5: Overview
Installation & operation manual overview this manual contains installation and programming instructions for the orion® se network gateway transceiver. Proper performance and reliability of the network gateway transceiver depends upon installation in accordance with these instructions. Product descri...
Page 6
Orion® se network gateway transceiver mounting the orion se network gateway transceiver important transceiver installation, mounting and disposal shall be in accordance with all local, state and federal regulations. When installing the transceiver, the customer is responsible for complying with loca...
Page 7
Installation & operation manual tools and materials (customer-supplied) • phillips #2 screwdriver • precision slotted screwdriver with a 2.0 millimeter (0.079 inch) blade size • two 9/16-inch or adjustable wrenches for mounting v-block clamps (standard mounting) • band-it ® tool (refer to page 9 ) a...
Page 8
Orion® se network gateway transceiver using the v-block clamps this mounting equipment is sized to mount the network gateway transceiver on a vertical or horizontal pole with outer diameters ranging from 1-1/4 inches to 2-1/2 inches. For mounting on poles larger than 2-1/2 inches, refer to "banding ...
Page 9
Installation & operation manual 7. Place a lock washer and nut on each bolt and tighten the nuts 100…150 inch-pounds to ensure the network gateway transceiver is sufficiently secured to the pole. 8. Repeat steps 7 and 8 for attaching the v-block clamp mounting bracket hardware to the bottom bolts of...
Page 10
Orion® se network gateway transceiver note: n installation of banding mounting kit requires use of the band-it tool shown below (66042-006) or equivalent band-it tool as recommended by band-it. Figure 7: band-it tool 1. Locate the band-it tool and supplied installation instructions. 2. Follow the ba...
Page 11: Electrical Installation
Installation & operation manual electrical installation ac power badger meter provides an ac-to-dc power supply that plugs into a standard three-prong 120v ac outlet. If powering the network gateway transceiver directly via dc power, please refer to the dc power information on page 17 . Figure 9: 12...
Page 12
Orion® se network gateway transceiver 2. Strip the cable outer jacket to a maximum length of 1.1 inches. Figure 11: stripped cable wires 3. Shorten the foil shield flush with the outer jacket. 4. Strip the ends of the six (6) colored wires to a length of 1/8 inch. Twist the conductors on each wire. ...
Page 13
Installation & operation manual figure 13: bottom of network gateway transceiver (gprs unit shown) 8. Remove the m12 cap from the m12 receptacle on the bottom of the network gateway transceiver and discard the cap. 9. Connect the m12 plug connector assembly to the m12 receptacle and tighten the lock...
Page 14
Orion® se network gateway transceiver electrical / network installations access to power and use of a nema 4 enclosure • the orion se network gateway transceiver requires access to power and can use either a 120v ac grounded outlet for use with the ac-to-dc power supply and power cord (66528-002) or...
Page 15
Installation & operation manual orion se lan recommended installation note: n consult the manufacturer's installation and usage recommendations as well as appropriate codes, regulations and standards for the lan rj45 ethernet connection. Ac to dc power supply with 308 in-line connector end and power...
Page 16
Orion® se network gateway transceiver orion se lan power over ethernet (poe) recommended installation note: n consult the manufacturer's installation and usage recommendations as well as appropriate codes, regulations and/or standards for the lan rj45 ethernet connection. To utility network cat5e ou...
Page 17
Installation & operation manual dc power source installation the orion se network gateway transceiver may be ordered with a 10-foot dc power source cable for direct connection with a customer-supplied dc power source (24v dc @ 1a minimum). When connecting an ac-to-dc power supply, the electrical req...
Page 18
Orion® se network gateway transceiver rj45 plug assembly (for lan connectivity only) required supplies: • rj45 plug assembly (66527-001) • ethernet cable cordset using outdoor-rated cat.5e cable and rj45 jack (customer supplied) • wrenches – 1-1/16 inch (customer supplied) figure 19: rj45 plug compo...
Page 19
Installation & operation manual figure 21: rj45 plug assembly with code a orientation 4. Insert the insulator assembly into the metallic housing using the code a orientation as shown in figure 21. An audible click will confirm complete connection. Note: n code a orientation must be used or the plug ...
Page 20: Battery Backup Replacement
Orion® se network gateway transceiver battery backup replacement in the event a battery replacement is required, please complete the installation steps as detailed below in the order presented. Important working with electronics requires the use of proper electrostatic discharge (esd) protection. Gr...
Page 21: Battery Disposal
Installation & operation manual note: n the battery is held in place by the enclosure cover only. No other adhesive or locking mechanism is used. 3. Remove the battery from the unit (figure 25) and safely discard the battery (see "battery disposal" on page 21 ). Figure 25: battery removal 4. Place t...
Page 22
Orion® se network gateway transceiver intentional blank page page 22 june 2012.
Page 23
Installation & operation manual intentional blank page page 23 june 2012.
Page 24
Www.Badgermeter.Com orion and readcenter are registered trademarks of badger meter, inc. Other trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and enhancements, badger meter reserves the right to change product or ...