1. DL manuals
  2. Baileigh
  3. Dust Collector
  4. DC-2100C
  5. Operator's Manual

Baileigh DC-2100C Operator's Manual

Summary of DC-2100C

  • Page 1

    Operator’s manual dust collector model: dc-2100c © 2012 baileigh industrial, inc. Reproduction of this manual in any form without written approval of baileigh industrial, inc. Is prohibited. Baileigh industrial, inc. Does not assume and hereby disclaims any liability for any damage or loss caused by...

  • Page 2: Table Of Contents

    Table of contents thank you & warranty .......................................................................................... 1 introduction ............................................................................................................ 3 general notes..................................

  • Page 3

    1 1 thank you & warranty thank you for your purchase of a machine from baileigh industrial. We hope that you find it productive and useful to you for a long time to come. Inspection & acceptance. Buyer shall inspect all goods within ten (10) days after receipt thereof. Buyer’s payment shall constitu...

  • Page 4

    2 2 force majuere. Seller shall not be responsible for any delay in the delivery of, or failure to deliver, goods due to causes beyond seller’s reasonable control including, without limitation, acts of god, acts of war or terrorism, enemy actions, hostilities, strikes, labor difficulties, embargoes,...

  • Page 5

    3 3 introduction the quality and reliability of the components assembled on a baileigh industrial machine guarantee near perfect functioning, free from problems, even under the most demanding working conditions. However if a situation arises, refer to the manual first. If a solution cannot be found,...

  • Page 6: Important

    4 4 learn to recognize safety information this is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury! Follow recommended precautions and safe operating practices. Understand signal words a signal word – danger, warning, ...

  • Page 7

    5 5 protect eyes wear safety glasses or suitable eye protection when working on or around machinery. Dust hazard wear appropriate dust mask. Dust created while using machinery can cause cancer, birth defects, and long term respiratory damage. Be aware of the dust hazards associated with all types of...

  • Page 8: Warning:

    6 6 safety precautions wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal ...

  • Page 9

    7 7 safety precautions (cont.) 11. Check for damaged parts. Before using any tool or machine, carefully check any part that appears damaged. Check for binding of moving parts that may affect proper machine operation. 12. Observe work area conditions. Do not use machines or power tools in damp or wet...

  • Page 10

    8 8 technical specifications motor 3 hp (2.23kw) 220v, 60hz, 1ph amp 18a motor speed 3450 rpm suction capacity 2100 cfm static pressure 11 ” h 2 o (279mm h 2 o) impeller size 15 ” (381mm) inlet size 8 ” x 4” x 3” (203 x 102 x 76mm) switch magnetic shipping dimensions (2 pkg.) 54.75 ” x 31.9” x 38.75...

  • Page 11: Warning:

    9 9 installation important: maintain an adequate working area around the machine for safety. Have the work area well illuminated with proper lighting. Remove scrap and waste materials regularly, and make sure the work area is free from obstructing objects. Keep the floor free of oil and make sure it...

  • Page 12: Caution:

    10 10 electrical motor specifications your tool is wired for 220 volt, 60hz alternating current. Before connecting the tool to the power source, make sure the machine is cut off from power source. Connections a separate electrical circuit should be used for your tools. If an extension cord is used, ...

  • Page 13

    11 11 check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that have grounding type plugs and receptacles that accept the tool’s plug. Repair or...

  • Page 14

    12 12 contents of package.

  • Page 15

    13 13 item description qty. Part list no. A main housing 1 no.16 b cone 1 no.33 c base 1 no.25 d stand 2 no.22 e canister filter 1 no.55 f drum 1 no.48 g cone clamp 1 no.31 h drum lid 1 no.40 i inlet adapter 1 no.18 j canister filter support 1 no.26 k hose 1 no.59 l hose 1 no.39 m hose clamp 12- 1/2...

  • Page 16

    14 14 hardware package item description specification qty. Part list no. A phillips head screw 3/16” x 3/8” 1 no.17 b flange bolt screw 5/16” x 1/2” 28 no.21 c phillips head screw m5 x 8 8 no.35 d phillips head screw 1/4” x 1/2” 2 no.43 e flange bolt screw 1/4” x 3/8” 2 no.27 f open wrench 10 x 12mm...

  • Page 17

    15 15 assembly instruction 1. Secure the base (no.25) and base wheels (no.24 and 24-1) with 5/16 ” x 1/2” flange bolt screw (no.21). See fig. 1. 2. Place and secure the stand (no.22) with 5/16” x 3/4 ” flange bolt screw (no.8) as fig. 1. 3. Tighten the wheels (no.47) under the collecting drum (no.48...

  • Page 18: Caution:

    16 16 4. Using an assistant, lift up the main housing (no.16) then place on the stand (no.22). Using the flange bolt screw 5/16” x 1/2" (no.21) to tighten together. See (fig.3). 5. Place the main housing (no.16) and cone (no.33), and then secure with cone clamp (no.31) and hex head bolt 1/4" x 2- 1/...

  • Page 19

    17 17 6. Paste foam (no.54) as a circle on canister filter (no.55) as fig. 5. 7. Secure the canister filter support (no.26) and base (no.25) with flange bolt screw 5/16 ” x 3/4 ” (no.8). 8. Assemble the canister filter (no.55) on the main housing (no.16) and canister filter support (no.26), and then...

  • Page 20

    18 18 9. Secure hose clamp (no.58) on both side of hose (no.59), then assemble and tighten hose (no.59) on outlet (no.16) and canister filter (no.55) with hose clamp (no.58). 10. Assemble and tighten pe bag (no.52) on bottom of canister filter with bag clamp (no.53). See (fig.7). 11. Assemble inlet ...

  • Page 21

    19 19 13. Assemble and tighten hose (no.39) on cone (no.33) and drum lid (no.40) with hose clamp (no.38). 14. Pull down the quick lever, and then assemble drum lid (no.40) and quick handle with long nut 3/8” (no.41). See (fig.9) 15. All the assembly steps are completed. See (fig.10) fig. 9 fig. 10

  • Page 22

    20 20 exploded diagram sheet 1.

  • Page 23

    21 21 exploded diagram sheet 2.

  • Page 24

    22 22 exploded diagram sheet 3.

  • Page 25

    23 23 part list item description specification qty. 1 motor 3hp 1 2 bushing 3 3 nut 5/16” 4 4 spring washer 5/16 ” 4 5 motor cord 1 6 key 7 x 7 x 25mm 1 7 motor washer 1 8 flange bolt screw 5/16” x 3/4” 16 9 hanger 5/16” 2 10 motor plate 1 11 hex head bolt 5/16” x 1” 4 12 set screw 3/8 ” x 3/4” 1 13...

  • Page 26

    24 24 item description specification qty. 31 cone clamp 1 32 hex head bolt 1/4” x 2-1/2” 1 33 cone 1 34 quick handle 2 35 phillips head screw m5 x 8 18 36 nut 3/8” 2 37 foam 2 38 hose clamp 12-1/2 ” 2 39 hose 12” 1 40 drum lid 1 41 long nut 3/ 8” 2 42 drum handle 1 43 phillips head screw 1/4” x 1/2”...

  • Page 27

    25 25 item description specification qty. 65 button head screw m5 x 16 2 66 nut 5/16” 1 67 set screw 5/16” x 3/4” 1 68 handle 1 69 cap 3/4” 1 70 sponge 7/8” 1 71 button head screw m5 x 6 6 72 bottom fixing support 1 73 anti-dust cover 1 74 gear m1.25 x t20 2 75 set screw m5 x 10 2 76 nut m5 2 77 bea...

  • Page 28

    26 26 notes baileigh industrial, inc. 1625 d ufek d rive m anitowoc , wi 54220 p hone : 920. 684. 4990 f ax : 920. 684. 3944 www . Baileighindustrial . Com baileigh industrial, inc. 1455 s. C ampus a venue o ntario , ca 91761 p hone : 920. 684. 4990 f ax : 920. 684. 3944 baileigh industrial ltd. U n...