Band Shoppe LONG RANGER IV Operating Instructions And Troubleshooting Manual - page 5
F I R S T P L A C E S T A R T S H E R E ™
PH 800.457.3501 • BANDSHOPPE.COM
UPDATED 10.07.2004
LONG RANGER IV: OPERATING INSTRUCTIONS & TROUBLESHOOTING GUIDE
5
SYSTEM SETUP RULES
This section includes some basic rules that will ensure trouble-free operation of your Long Ranger system.
1.
Make sure the transmitter battery is good, or better yet, new.
2.
Charge up the battery pack in the Long Ranger fully before you use the system. Charge until the green charging lamp underneath
the CHARGER jack on the Long Ranger control panel goes out.
3.
Set up the system so that the Long Ranger is as far from large metal surfaces as possible. Metal surfaces under the unit
(such as pickup truck cabs or a car top) are generally no problem but large metal surfaces alongside the Long Ranger may
interfere with wireless reception.
4.
If you have more than one transmitter on the same frequency, turn on only one transmitter at a time. You cannot use two transmitters
at the same time with a single Long Ranger. You will need to “alternate” back and forth between the transmitters. Failure to do so will result
in an obnoxious whining sound from the system, and the audio will probably not be understandable. “Add-on” wireless mic systems are
available separately to permit operation of two transmitters simultaneously through a single Long Ranger.
5.
Use the minimum volume that will enable everyone to hear. It doesn’t have to be loud to be heard.
6.
Always turn the power off before connecting or disconnecting external speakers.
7.
The Long Ranger should be elevated for best coverage. The unit should ideally be at least 2 feet higher than the audience. For example,
with an audience standing on fl at ground, the number of people that can hear clearly will double if you raise the unit from 5 feet above
the ground to 7 feet ablove the ground.
8.
During actual operation the Long Ranger should be located at least 20 feet away from the person using the microphone and aimed so
that the sound from the speaker is directed toward the audience and away from the microphone. This will reduce feedback problems.
“Feedback” is a loud squealing sound coming from the speaker when the volume is too high or the microphone is too close to the Long
Ranger. Feedback is generally much more of a problem when using lavalier (lapel) type microphones. The headset models are recommended
for use with the Long Ranger system since they place the microphone pickup much closer to your mouth, which increases the loudness of the
Long Ranger before feedback occurs.
INITIAL EQUIPMENT ADJUSTMENTS
This section covers the initial adjustments to the transmitter and Long Ranger that must be made before the system is placed into operation.
The step-by-step procedures are listed in the order in which they should be performed:
1.
Turn Long Ranger power on – The POWER lamp lights.
2.
Rotate both volume controls counter-clockwise to their minimum settings.
3.
Position yourself behind the Long Ranger so that the sound from the speaker will be directed away from the microphone.
4.
Plug your microphone into the transmitter. Rotate the plug clockwise to make sure the connection is locked.
5.
Turn the transmitter power on and verify that the red lamp on it lights. If the lamp is very dim or does not light, replace the battery.
6.
Observe that the green RF lamp on the Long Ranger control panel is lighted. This verifi es that the unit is receiving a usable
signal from the transmitter.
7.
Position the microphone on yourself (or other user) in the location it will be during actual operation. If you are using the single-band
or dual-band headset microphone, turn the white knob on the headset fully clockwise (maximum). The HM162 over-ear microphone
should be positioned so that the pickup element is just to the left of the mouth, so that breath pops do not strike the capsule. Lavalier
microphones should be positioned high on the chest or collar, as close to the mouth as possible to minimize the possibility of “feedback.”