- DL manuals
- Bannon
- Fan
- 57937
- Owner's Manual
Bannon 57937 Owner's Manual
Summary of 57937
Page 1
Read & save these instructions 100in. High volume ceiling fan owner’s manual warning: read carefully and understand all assembly and operation instructions before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item #57937.
Page 2
Page 2 of 21 thank you very much for choosing a bannon ™ product! For future reference, please complete the owner’s record below: serial number/lot date code: ________________________________ purchase date: ____________________________________________ save the receipt, warranty, and this manual. It ...
Page 3
Page 3 of 21 table of contents intended use .......................................................................................................................................... 4 packaging contents ...................................................................................................
Page 4
Page 4 of 21 intended use the bannon 100in. High volume ceiling fan is designed for large, high ceiling areas such as factories, barns, ranches, gyms, and warehouses. The low electric usage is perfect for continuous use. Packaging contents motor (1) blade pack (8) remote control (1) hanger bracket &...
Page 5
Page 5 of 21 work area safety inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not u...
Page 6
Page 6 of 21 disconnect the power/air supply from the product and place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store the product when it is n...
Page 7
Page 7 of 21 outlet box. When cutting or drilling in the ceiling or wall, do not damage electrical wiring and other hidden utilities. To reduce the risk of injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blad...
Page 8
Page 8 of 21 all set screws must be checked and re-lightened where necessary before installation. Preparing for installation unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Downrod installation vaulted ceiling i...
Page 9
Page 9 of 21 mounting bracket installation remove the screws from the two matching holes (1) on canopy. Loosen (do not remove) the screws in the matching slots (2) on the canopy. Rotate the mounting bracket and remove from the canopy. Install mounting bracket to the outlet box in the ceiling using t...
Page 10
Page 10 of 21 downrod assembly (included) remove clamp pin (1) and cross pin (2) from down rod (3). Feed motor lead wires through downrod and canopy assembly and insert downrod into downrod yoke. Make sure to align holes in downrod with the hole in the yoke. Install yoke cross pin (1) through yoke a...
Page 11
Page 11 of 21 downrod preparation re-install pin into downrod. Slide the downrod ball up to the top of the downrod. Re-install the screw to secure ball to downrod. Note: some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the se...
Page 12
Page 12 of 21 wiring diagram make wiring connection from the housing and the motor to the remote receiver as shown above. Connect using wire nuts (provided). Once the wiring step has been completed, slide the wired remote receiver (1) in between the mounting bracket (2) and the top of the down rod b...
Page 13
Page 13 of 21 2 1 attaching blades to fan insert the blades (5) through the slots on the motor housing as shown. Use the provided screws (1), washers (2), and bolts (3) to tighten the blades to the pre-attached blade brackets (4). Mount the transmitter holder onto the wall using screws provided. Pla...
Page 14
Page 14 of 21 before each use ⚠warning be sure obstructions are not in the fan’s path of operation. Check that batteries are in good condition in the remote control transmitter. Operating instructions ⚠warning to reduce the risk of electric shock, or personal injury, mount to outlet box marked “acce...
Page 15
Page 15 of 21 setting fan air flow note: be sure the slide switch is pushed firmly to one side or the other. The fan will not operate with the slide switch in the middle. To reverse the direction of the blades, slide the reverse switch (located on the top of the motor housing) to the opposite side. ...
Page 16
Page 16 of 21 note: turn off and wait for fan to come to a stop before changing the setting of the downward/upward slide switch. Controlling more than one fan with remote control the remote control transmitter and receiver are matched at the factory. With the matching process, the same remote contro...
Page 17
Page 17 of 21 troubleshooting ⚠warning turn off fan and breaker at electrical supply before attemping to do any adjustments to the fan. Failure possible cause corrective action fan wobbles in motion 1. Blades not secured or balanced 2. Be sure ball to hanger bracket is locked in place unplug from po...
Page 18
Page 18 of 21 parts diagram parts list reference part description quantity 1 mounting bracket 1 2 blades 8 3 canopy 1 4 downrod 1 5 fan motor 4 6 hardware pack 1 6a mounting screw and nut 4 6b blade screws and nuts 24 6c screw 2 6d wire nuts 8 63 blade screw washers 24 7 remote control with wall bra...
Page 19
Page 19 of 21 replacement parts for replacement parts and technical questions, please call customer service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequenc...
Page 20
Page 20 of 21 limited warranty northern tool and equipment company, inc. ("we'' or ''us'') warrants to the original purchaser only ("you" or ''your'') that the bannon product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period o...
Page 21
Page 21 of 21 distributed by: northern tool & equipment company, inc. Burnsville, minnesota 55306 www.Northerntool.Com made in china.