1. DL manuals
  2. Barbeques Galore
  3. Grill
  4. EDV27-BQ
  5. Use And Care Manual

Barbeques Galore EDV27-BQ Use And Care Manual - Rotisserie Assembly-27”

Manual is about: ENDEAVOR GRILL

Summary of EDV27-BQ

  • Page 1

    Endeavor grill use and care guide installation guide models: ■ edv27-bq ■ edv27-bqr ■ edv36-bqa ■ edv36-bqar.

  • Page 2: A Message To Our Customers

    1 thank you for selecting this professional “endeavor” series grills. Because of these appliances’ unique features we have developed this use and care guide and installation guide. It contains valuable information on how to properly operate and maintain your new appliance for years of safe and enjoy...

  • Page 3: Table of Contents

    2 safety practices & precautions ......................................................3-4 grill models .......................................................................................................5 gas requirements .............................................................................

  • Page 4

    3 important safety notice: certain liquid propane dealers may fill liquid propane cylinders for use in the grill beyond cylinder filling capacity. This “overfilling” may create a dangerous condition. • “overfilled” tanks can build up excess pressure. As a safety device, the tanks pressure relief val...

  • Page 5

    4 for personal safety, wear proper apparel. Loose fitting garments or sleeves should never be worn while using this appliance. Some synthetic fabrics are highly flammable and should not be worn while cooking. Only certain types of glass, heat-proof glass ceramic, earthenware, or other glazed utensil...

  • Page 6: Grill Models

    5 rotisserie grill grill ignition safety hold in 10 sec. While lighting (rotisserie) grill grill safety hold in 10 sec. While lighting (rotisserie) ignition edv27-bq edv27-bqr grill models rotisserie grill grill grill ignition safety hold in 10 sec. While lighting (rotisserie) grill grill safety hol...

  • Page 7: Gas Requirements

    6 verify the type of gas supply to be used, either natural or lp, and make sure the marking on the appliance rating plate agrees with that of the supply. Never connect an unregulated gas line to the appliance. An installer supplied gas shut-off valve must be installed in an easily accessible locatio...

  • Page 8: Gas Requirements

    7 lp gas hook up (type 1 or qcc1 regulator): grills orificed for use with lp gas come equipped with a high capacity hose/regulator assembly for connection to a standard 20 lb. Lp cylinder (type 1). The lp tank is not included. Connection: 1/2" npt male with a 3/8" flare adapter (included). Lp hose w...

  • Page 9

    8 insulated jacket: do not build the grill under overhead unprotected combustible construction. If the grill is to be placed into a combustible enclosure, an approved insulated jacket is necessary and is available from your dealer. Use only the insulated jacket which has specifically been designed a...

  • Page 10: Built–In Grill Clearances

    9 rotisserie safety ignition (to left and right side of grill to combustible construction) (with rotisserie motor mounted) rotisserie motor (lid) 6" 36" 27 3/4 " 27 3/8 " (cutout) 3" (to non- combustible construction/ min. Lid clearance) 12" (to combustible construction) grill exhaust 26 1/2 " (to l...

  • Page 11

    10 3" (to non-combustible construction / min. Lid clearance) 12" (to combustible construction) grill exhaust note: if using a backguard apron or rear wall, locate electrical service on the left hand side for rotisserie motor connection standard layout for non-combustible enclosure: 3" min. For lid c...

  • Page 12

    11 built–in construction details – 36” 3" (to non-combustible construction / min. Lid clearance) 12" (to combustible construction) grill exhaust note: if using a backguard apron or rear wall, locate electrical service on the left hand side for rotisserie motor connection standard layout for non-comb...

  • Page 13: Leak Testing

    12 general: although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check t...

  • Page 14

    13 installer final checklist: grill burner flame height: to access the grill burner air shutters first remove the valve panel by removing the four screws on the corners of the valve panel. Remove the control knobs. Pull the valve panel outward. With a screw driver, loosen the lock-screw on the face ...

  • Page 15

    14 warning: important! Before lighting, inspect the gas supply piping or hose prior to turning the gas "on". If there is evidence of cuts, wear, or abrasion, it must be replaced prior to use. To adjust: 1. Be careful as the burner may be very hot. 2. If the flame is yellow, indicating insufficient a...

  • Page 16: Using The  Grill

    15 the replacement pressure regulators and hose assembly must be the type specified by the manufacturer. Do not use the grill if the odor of gas is present. The pressure regulator and hose assembly supplied with the unit must be used. If the unit is lp, screw the regulator into the tank and leak che...

  • Page 17

    16 using the grill lp gas: note: your preheat time may be shorter than recommended when using lp gas. To prevent overcooking you may want to lower heat settings. Grilling requires high heat for searing and proper browning. Most foods are cooked at the “medium” heat setting for the entire cooking tim...

  • Page 18: Lighting Instructions

    17 manual lighting: if the burner will not light after several attempts then the burner can be manually lit. If you’ve just attempted to light the burner with the igniter, allow 5 minutes for any accumulated gas to dissipate. Keep your face and hands as far away from the grill as possible and hold a...

  • Page 19: Using The  Rotisserie

    18 bqr and bqar models only: the grill rotisserie system is designed to cook items from the back using infrared heat. The location of the burner allows the placement of the rotis basting pan (included) beneath the food to collect juices and drippings for basting and gravy. To flavor the contents of ...

  • Page 20: Using The  Rotisserie

    19 to light the rotisserie burner (bqr and bqar models only): the location of the rotis burner makes it more susceptible to strong wind conditions, more so than the protected grill burners. For this reason you should avoid operating the rotis during windy conditions. As an added safety feature we’ve...

  • Page 21: Care And  Cleaning

    20 battery replacement: 1. Remove grease tray. 2. Open cart door. 3. Pull battery downwards (this may require use of pliers.) note: re-install upward and push to snap. Note: polarity as shown in fig. 14. Grill racks: the easiest way to clean the grill is immediately after cooking is completed and af...

  • Page 22: Burner Removal And Cleaning

    21 grill and orifice cleaning: remove the grill racks, then lift out the grill radiant tray. Grasp the burner, pull it up and slightly to the rear of the unit so the burner head comes off the brass orifice at the front, angle the burner sideways, and remove. Burner cleaning clean the exterior of the...

  • Page 23: Troubleshooting

    22 before calling for service: if the grill does not function properly, use the following checklist before contacting your dealer for service. You may save the cost of a service call. Troubleshooting is for general purposes only. If the problem persists and you feel you require service, contact your...

  • Page 24: Grill Burner Assembly-27”

    23 1 2 3 4 6 19 9 8 17 18 10 14 12 20 21 13 15 11 5 7 item description part no. 1 grill rack s/s 27 19014-02 2 radiant 32889 3 pyramid rock 10436 4 27”c/ heat shield w/assy. 32220 5 ss grill burner 12285 6 air shutter screw 12003-2 7 27” heat shield 32336 22 item description part no. 8 manifold 27 1...

  • Page 25: Grill Body Parts List-27”

    24 item description part no. 1 folding lid w/assy. Edv27 32882-01 2 handle end cap spacer 18446 3 handle end cap 18443-pl 4 shoulder bolt 15003-15 5 handle lid 32886-01 6 warming rack galore 27 18444 7 body assembly 27 edv grill 38848-01 8 bolt (small) 15002-26 9 warming rack ret. 27 l/h 32340-01 wa...

  • Page 26: Rotisserie Assembly-27”

    25 item description part no. 1 rotisserie handle 18040 2 meat holder assembly 19010-02 3 rotisserie rod 27 19487-01 4 rotis receiving bracket 32846 5 rotisserie burner 27dbqar 12021-2 6 orifice elbow 18193 7 plug orifice lp 13025-56 plug orifice ng 13025-50 8 screws 15001-23 9 rotisserie motor 16026...

  • Page 27: Grill Burner Assembly-36”

    26 1 2 3 4 6 19 9 8 17 18 10 14 10 20 21 13 15 11 5 7 item description part no. 1 grill rack s/s 36 19014-02 1a grill rack 9” 19486 2 radiant 32889 3 pyramid rock 10436 4 36”c/ heat shield w/assy. 32268 5 ss grill burner 12285 6 air shutter screw 12003-2 7 36” heat shield 32880 22 item description p...

  • Page 28: Grill Body Parts List-36”

    27 item description part no. 1 folding lid w/assy. Edv36 32882-02 2 handle end cap spacer 18446 3 handle end cap 18443-pl 4 shoulder bolt 15003-15 5 handle lid 32886-02 6 warming rack galore 36 18444-01 7 body assembly 36 edv grill 38848-02 8 bolt (small) 15002-26 9 warming rack ret. 36 l/h 32340-01...

  • Page 29: Rotisserie Assembly-36”

    28 item description part no. 1 rotisserie handle 18040 2 meat holder assembly 19010-02 3 rotisserie rod 36 19487-02 4 rotis receiving bracket 32846 5 rotisserie burner 36dbqar 12021-2 6 orifice elbow 18193 7 plug orifice lp 13025-56 plug orifice ng 13025-50 8 screws 15001-23 9 rotisserie motor 16026...

  • Page 30

    29 item description part no. 1 side panel l/h 32906 2 front panel-36” 32864-02 front panel-27” 32864-01 3 bottom cart l/h shelf 32921 4 door assembly-36’ 32905 door assembly-27” 32874 5 caster locking 3 18027 6 caster stiffner 41109 7 caster without brake 3 18027-1 8 bottom cart r/h shelf 32918 item...

  • Page 31: Head and Cart Assembly

    30 head and cart assembly 1. Put cart on a flat surface. 2. Install head on the cart (2 people required to lift head). 3. Using bolt and nut (6 required), attach head to the cart. 4. Install shelves to the side of the head with bolt and nut (8 required), putting washers between head and shelves. Hea...

  • Page 32: Wiring Diagram For Edv27-Bq

    31 wiring diagram for edv27-bq.

  • Page 33: Wiring Diagram For Edv27-Bqr

    32 wiring diagram for edv27-bqr.

  • Page 34: Wiring Diagram For Edv36-Bqa

    33 wiring diagram for edv36-bqa.

  • Page 35

    34 wiring diagram for edv36-bqar.

  • Page 36: Service

    35 how to obtain service: for warranty service, contact customer service at 877-553-0243. Before you call, please have the following information ready: • model number • serial number • date of installation • a brief description of the problem your satisfaction is of the utmost importance to us. If a...

  • Page 37: Warranty

    36 length of warranty: one (1) year full parts and labor covers the entire product five (5) year comprehensive warranty covering grill radiant assemblies, and drip pans. Should structural deterioration occur to the degree of non-performance, a replacement will be furnished. Lifetime warranty on all ...

  • Page 38

    Part no. 17519 rev. B litho in usa 10/2002 as product improvement is an ongoing process, we reserve the right to change specifications or design without notice. Barbeque’s galore 15041 bake parkway suite-a irvine, ca 92618 tel: 949-597-2400