1. DL manuals
  2. Barco
  3. Projector
  4. Cine VERSUM 50
  5. Owner's Manual

Barco Cine VERSUM 50 Owner's Manual

Other manuals for Cine VERSUM 50: Installation Manual
Manual is about: CINE VERSUM SYSTEM

Summary of Cine VERSUM 50

  • Page 1

    B arco p rojection c ine versum s ystem r9001870 r9005010 r9841020 o wner ’ s manual 17012003 r5976490/01.

  • Page 2

    Barco nv home cinema noordlaan 5, b-8520 kuurne phone: +32 56.36.84.30 fax: +32 56.36.88.62 e-mail: salesassistantht.Bci@barco.Com visit us at the web: www.Homecinema.Barco.Com printed in belgium.

  • Page 3

    Copyright © all rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of barco. Changes barco provides this manual “as is” without warranty of any kind, eith...

  • Page 5: Table Of Contents

    Table of contents table of contents 1. Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 general safety instructions . . . . . . . . . . . . . ...

  • Page 6

    Table of contents 2 r5976490 cine versum system 17012003.

  • Page 7: 1. Safety Instructions

    1. Safety instructions 1. Safety instructions overview • general safety instructions • module related safety instructions this manual is intended for the user/operator of the installed digital video distribution system. Any change in cabling or servicing of the installed modules must be performed by...

  • Page 8

    1. Safety instructions protection from ultraviolet radiation warning: do not look directly in the high intensity light beam. The lamp contained in this product is an intense source of light and heat. One component of the light emitted from the lamp is ultraviolet light. 1.2.2 cine versum 50 lightnin...

  • Page 9: 2. System Configuration

    2. System configuration 2. System configuration overview • the video distribution solution • overview of the system 2.1 the video distribution solution the cine versum revolution thank you for purchasing the cine versum system from barco. You are now at the gates of projection heaven. The cine versu...

  • Page 10

    2. System configuration image 2-2 display link 6 r5976490 cine versum system 17012003.

  • Page 11

    3. Overview user’s controls 3. Overview user’s controls overview • cine versum master • cine versum 80 • cine versum 50 • remote control • remote control operation 3.1 cine versum master front view the front side of thecine versum master is provided with the following controls: image 3-1 front side ...

  • Page 12

    3. Overview user’s controls image 3-2 cine versum 80 controls controls function description ref. Function description 1 infra red receiver reception diode for the ir signals from the remote control. Allows switching on/off (standby) of the projector separately and controlling the cine versum master....

  • Page 13

    3. Overview user’s controls image 3-3 cine versum 50 controls controls function description ref. Function description 1 main power switch switches the cine versum 50 in the standby mode. Operation mode is controlled by the cine versum master. 2 infra red receiver reception diode for the ir signals f...

  • Page 14

    3. Overview user’s controls image 3-4 remote control controls function description ref. Function description 1 address button to match the remote control with the unit that you are addressing (number between 0 and 9). 2 standby button to power up/down the cine versum master and the displays in the l...

  • Page 15

    3. Overview user’s controls digit button stored source 4 5 6 7 8 3.5 remote control operation overview • general • battery insertion in the remote control • visualization of commands 3.5.1 general how to use the remote control allows you to control your cine versum master, even when it is built into...

  • Page 16

    3. Overview user’s controls factory address setting of the modules the factory address setting of the modules is as follows: module individual address common address cine versum 80 address no common address cine versum 50 address no common address cine versum master address common address common add...

  • Page 17

    3. Overview user’s controls how to reinstall the address by removing the batteries, the address in the remote control will be set to 0. In case the different modules are controlled separately (own address), the respective address of the module you desire to control has to be set. To reinstall an add...

  • Page 18

    3. Overview user’s controls image 3-14 on-screen message image 3-15 message on master display image 3-16 on-screen bar scale image 3-17 bar scale on master display 14 r5976490 cine versum system 17012003.

  • Page 19

    4. Switching on/off the cine versum system 4. Switching on/off the cine versum system overview • brief introduction • upon first startup • switching the system between operation and standby • switching the system between standby and economic standby • switching the system off completely and back to ...

  • Page 20

    4. Switching on/off the cine versum system image 4-2 cine versum 80 image 4-3 cine versum master jog dial image 4-4 power up selection 4.3 switching the system between operation and standby overview • from operation mode to standby mode • from standby mode to operation mode 4.3.1 from operation mode...

  • Page 21

    4. Switching on/off the cine versum system using the remote control 1. Point the remote control to the front of the cine versum master or to the cine versum 80. 2. Press the standby button . (image 4-9) the cine versum master and the cine versum 80 go from operation to standby. Image 4-9 4.3.2 from ...

  • Page 22

    4. Switching on/off the cine versum system image 4-12 economic standby using the remote control 1. Point the remote control to the front of the cine versum master or to the cine versum 80 2. Toggle with the ↑ or ↓ arrow keys until “economic” in the menu on the cine versum master is pointed to (image...

  • Page 23

    4. Switching on/off the cine versum system 4.6 turning on the system from total off mode how to turn on the system back to operation mode 1. Press the power switch on the cine versum master (image 4-1). The cine versum master goes from off to standby. (image 4-15) 2. Press the power switch on the ci...

  • Page 24

    4. Switching on/off the cine versum system 20 r5976490 cine versum system 17012003.

  • Page 25

    5. Direct source selection 5. Direct source selection 5.1 from standby mode using the digit buttons on the remote control 1. Make sure that the connected sources to the cine versum master are turned on. 2. Using the digit button on the remote control, key in the corresponding slot number (from 1 to ...

  • Page 26

    5. Direct source selection 5.2 return to standby mode how to return to standby remotely 1. Point the remote control to the front of the cine versum master or the cine versum 80. 2. Press the standby button on the remote control again. (image 5-2) the cine versum master switches to the standby mode a...

  • Page 27: 6. Image Control

    6. Image control 6. Image control image controls the brightness, contrast, sharpness (detail), color and tint functions are directly accessible with the remote control. The adjustment functions, when selected, display a slide bar overlayed on the source image. It is useful to adjust the brightness, ...

  • Page 28

    6. Image control image 6-3 image 6-4 6.3 sharpness (detail) control how to adjust the sharpness the sharpness function is used to adjust the image sharpness of video signals when using a video decoder installed in the cine versum master. To adjust the sharpness, press the (+) or (-) side of the butt...

  • Page 29

    6. Image control 6.4 color (saturation) control how to adjust the color (saturation) the color function is used to adjust color saturation levels and is only active for video and s-video sources. To adjust color, press the (+) or (-) side of the button ’color’ (image 6-7). The following barscale is ...

  • Page 30

    6. Image control image 6-9 image 6-10 26 r5976490 cine versum system 17012003.

  • Page 31: Index

    Index index c cine versum 5 system configuration 5 cine versum system 15 switching on/off the system 15 f first startup 15 i image control 23–25 brightness 23 color (saturation) 25 contrast 23 sharpness 24 tint 25 introduction 15 on/off 15 l location of user controls 9 location of user’s controls 7–...