- DL manuals
- Barco
- Projector
- F85
- Command Reference Manual
Barco F85 Command Reference Manual
Summary of F85
Page 1
F(l)35, fs35 ir, f85 ascii commands protocol reference manual 601–0381–00/00 21/10/2015.
Page 2
Barco fredrikstad as habornveien 53, n-1630 gamle fredrikstad, norway phone: +47 6930 4550 fax: +47 6930 4580 support: support.Fre@barco.Com visit us at the web: www.Barco.Com printed in no.
Page 3
Changes barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) desc...
Page 5: 1. Communication Settings
1. Communication settings 1. Communication settings overview • set up lan communication • set up rs232 communication 1.1 set up lan communication general the supported rs232 settings are as follows: parameter data baud rate 19200 data bits 8 parity none. There is no parity bit used to perform error ...
Page 6
1. Communication settings maximum length of the rs-232 cable is 15.25m (50ft). 2 601–0381–00 f(l)35, fs35 ir, f85 21/10/2015.
Page 7
2. Communication protocol definitions 2. Communication protocol definitions about this section describes the definitions used in the communications protocol. When the projectors are connected to either rs232 or lan you can control the projectors through this ascii based protocol. Some commands will ...
Page 8
2. Communication protocol definitions mnemonic modifier value target limitations 4 bytes 1 byte n bytes, max 6 bytes n bytes, max 4 inclusion required optional optional optional example powr a 1 cr mnemonic bytes (4 bytes) the mnemonic is a 4 byte ascii command (key identifier). This is required in ...
Page 9
2. Communication protocol definitions error code error message description !00002 not available logic conflict prevents command being available. For example, contrast is not available when the projector is searching for sources. !00003 not implemented command not available for this projector configu...
Page 10
Command description platforms operations supported level value target comments powr power gp3, gp4 get, set end user 0 - power off, 1 - power on post power state gp3, gp4 get end user see value table post iabs set source abs values gp3, gp4 get, set end user see value table iabs idvi select dvi gp3,...
Page 11
Hpos horizontal positon gp3, gp4 get, set end user only for analog sources vpos vertical position gp3, gp4 get, set end user only for analog sources freq frequency gp3, gp4 get, set end user only for analog sources phse phase gp3, gp4 get, set end user only for analog sources dcsp color space gp3, g...
Page 12
Dsyg desired yellow gain gp3, gp4 get, set end user dswg desired white gain gp3, gp4 get, set end user dfrx factory desired red x gp3, gp4 get, set manufacturing dfry factory desired red y gp3, gp4 get, set manufacturing dfrg factory desired red gain gp3, gp4 get, set manufacturing dfgx factory desi...
Page 13
Mfbx factory measured blue x gp3, gp4 get, set manufacturing mfby factory measured blue y gp3, gp4 get, set manufacturing mfbl factory measured blue luminance gp3, gp4 get, set manufacturing mfwx factory measured white x gp3, gp4 get, set manufacturing mfwy factory measured white y gp3, gp4 get, set...
Page 14
Ecom eco mode gp3, gp4 get, set end user 0 - disable, 1 - enable lpw1 lamp1 power gp3, gp4 get, set end user lpw2 lamp2 power gp3, gp4 get, set end user lmod lamp mode gp3, gp4 get, set end user see value table lmod ldly lamp auto switch delay gp3, gp4 get, set end user lpw1 led power gp3 get, set e...
Page 15
Rtch real time clock hour gp3, gp4 get, set end user rtcm real time clock minute gp3, gp4 get, set end user rtcs real time clock second gp3, gp4 get, set end user rtcd real time clock day gp3, gp4 get, set end user rtcn real time clock month gp3, gp4 get, set end user rtcy real time clock year gp3, ...
Page 16
Auxd ir led power gp3 led ir get, set end user gab1 set gamma abs value ir channel gp3 led ir wuxga get, set end user see value table gabs scmp sub channel mapping gp3 led ir wuxga and get, set end user 0 - rgb->rgb, 1 - r->rgb, 2 - g->rgb, 3 - b->rgb ibco individual brightness and contrast offset a...
Page 17
Menu menu navigate toggle osd menu gp3, gp4 set end user nvup menu navigate up gp3, gp4 set end user nvdw menu navigate down gp3, gp4 set end user nvlf menu navigate left gp3, gp4 set end user nvrh menu navigate right gp3, gp4 set end user nvok menu navigate ok gp3, gp4 set end user echo communicati...
Page 18
Indg internal sensor duration value green gp3 led get power user indb internal sensor duration value blue gp3 led get power user thrm thermal status gp3, gp4 get power user fan1 fan speed 1 gp3, gp4 get power user fan2 fan speed 2 gp3, gp4 get power user fan3 fan speed 3 gp3, gp4 get power user fan4...
Page 19
Lmbx lamp data mailbox gp3 get, set manufacturing data 0 - lamp 1, 1 - lamp 2 lmbp lamp data mailbox position gp3 get, set manufacturing data 0 - lamp 1, 1 - lamp 2 lmbc lamp data mailbox checksum gp3 get, set manufacturing data 0 - lamp 1, 1 - lamp 2 lamp data 3. Ascii command sets 601-0381-00_gp3/...
Page 20
Value tables iabs set source abs values value description 0 vga 1 1 vga 2 2 dvi 1 7 component 8 hdmi 1 10 dvi 2 11 hdmi 2 12 dual head dvi 13 dual head hdmi 14 dual head xp2 15 xp2 a 16 xp2 b sabs set scaling abs values value description 0 1:1 1 fill all 2 fill aspect ratio 3 fill 16:9 4 fill 4:3 5 ...
Page 21
Dscr desired coords mode value description 0 off 1 rgb 2 rgbcmy orie select orientation abs value value description 0 desktop front 1 ceiling rear 2 desktop rear 3 ceiling front osdc osd enable value description 0 osd off 1 osd show only warnings 2 osd on lmod lamp mode value description 0 single la...
Page 22
Lest status led state value description 0 green/blue on 1 green/blue flash 2 yellow on 3 yellow flash 4 red on 5 red flash dcsp digital colorspace value description 0 rgb 1 ypbpr 709 2 ypbpr 601 trgx trigger mode value description 1 on 2 off 3 screen 4 aspect tatb aspect trigger behavior target desc...
Page 23
Baud trigger mode value description 4800 4800 9600 9600 19200 19200 38400 38400 57600 57600 115200 115200 tbos 3d bnc sync-out signal value description 0 off 1 3d glass sync 2 3d display sync 3 passthrough flss framelock signal status value description 0 free running 3 locked tdss 3d lr signal statu...
Page 24
Lvce bit wise error code for led voltage calibration bit description 0 set red input voltage failed 1 read red adc current failed 2 read red drop out voltage failed 3 desired red input voltage out of range 4 red loop count exceed max value 10 set green input voltage failed 11 read green adc current ...