Barco HDF W series Quick Start Manual
HDF W series
Quick start guide
Mounting the lens
10/100 BASE-T
ETH
ACT PWR LMP
10/100 ERR IR ACT
WIFI
SEL
1 2 3 4
6 7 8 9
RGB
STBY
PAUSE
TEXT
PATTERN WINDOW
PIP
AUTO
Button panel
Communication interface
LED or Button
Color status
Description
Standby button
RED
on
Projector is in standby
RED
toggles on/off
Projector startup failed
GREEN
toggles on/off
Projector starts up
GREEN
on
Projector is on
WHITE toggles on/off
Projector goes from/to ECO standby
Pause button
RED
on
Shutter is closed
GREEN
on
Shutter is open
Dimmed WHITE
Shutter is closed, projector in standby
Full WHITE
Shutter is undefined
Full WHITE toggles on/
off
Shutter is closed during reset format-
ter
PWR (power LED)
Off
Projector powers up
RED
Projector is in standby
ORANGE
Projector is in ECO standby
GREEN
Projector is on
LMP (lamp LED)
Off
Lamp is off
RED
No lamp inserted
ORANGE
Lamp is on in ECO mode
GREEN
Lamp is on in normal mode
GREEN
-
ORANGE
Lamp is on in CLO mode
ERR (error LED)
Off
No error
RED
toggles on/off
Error
ORANGE
toggles on/off
Warning
IR
RED
IR signal received
GREEN
IR signal acknowledged
LED and Button indication chart
Overview window
(A)
•
Main source
•
PiP source
•
IP address
•
Customer ID
•
Lamp status
•
Mains voltage
•
Ambient temperature
•
Text status (OSD)
Lamp overview window
(B)
•
Number of strikes
•
Run time (hours)
•
Remaining run time (hours)
•
% lamp used
About window
(C)
•
Package version in use
•
Mgr Software in use
•
GUI Software in use
Common parts
•
Error and warning area (1)
•
Projector status (2)
Green
: projector works correctly
Red cross
: projector has errors
Yellow triangle
: projector has warnings
•
Remove foam in lens opening.
•
Place lens holder in unlock position. Handle A
towards socket B.
•
Gently insert the lens in such a way that the
lens connector matches the socket B.
•
Insert the lens until the connector seats into
the socket.
•
Secure the lens in the lens holder. Move
handle A into the lock position (away from
socket B).
•
Check if lens touches the front plate of the lens
holder.
•
Check if the lens is really secured by trying to
pull the lens out of the lens holder.
•
Put the safety cable around the lens between
the motor part and the mounting flange.
Mount the clamp.
A
B
C
1
2
B
1
2
A
A
1
2
Local LCD screens
Quick setup and operation
The following summarizes HDF setup and opera-
tion. For errorfree installation always refer to the
User Guide.
Connect power. Ensure that the power (200-
240 V @ 50/60hz) is properly connected to the
power input.
Connect available sources to the appropriate
input terminal.
Power on. Turn the mains switch to on.
Start up sequence starts. Local LCD displays a
start up screen
Standby button changes from red to green
when pressed.
Image of the latest selected input appears.
Adjust the lens settings by pressing the LENS
button or via the direct lens keys on the RCU
Auto image can load automatically the correct
file. The manual selection can be done via menu
or other control systems.
Orientation of the unit is set as standard in
table front projection mode. Change the projec-
tor set up in the ALIGNMENT > ORIENTATION
menu.
If geometrical distortion occurs this can
be corrected with the Warping settings in the
ALIGNMENT menu.
Tuning the image can be done in the IMAGE
menu or via the image settings on the RCU
Picture-in-Picture control can be done in the
LAYOUT menu or via the PiP button.
Lamp management in the LAMP menu.
Switching off the unit can be done by pressing
the STBY button for 3 sec. An aftercool up to
300 sec will start.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
www.barco.com/esupport
USA +1 866 374 7878
EMEA
+32 56 368019
APAC
+86 400 88 22726
Support
FLMW-Quickstartguide4.indd 1
16-11-2012 11:21:16