1. DL manuals
  2. Barco
  3. Projector
  4. HDF W series
  5. User And Installation Manual

Barco HDF W series User And Installation Manual

Manual is about: HDF series

Summary of HDF W series

  • Page 1

    Hdf series user and installation manual for hdf, hdf w22, hdf w26 and hdf w30 flex r5905158/09 08/12/2016.

  • Page 2

    Barco nv president kennedypark 35, 8500 kortrijk, belgium phone: +32 56.36.82.11 fax: +32 56.36.883.86 support: www.Barco.Com/en/support visit us at the web: www.Barco.Com printed in belgium.

  • Page 3

    Changes barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) desc...

  • Page 5: Table Of Contents

    Table of contents table of contents 1. Safety ................................................................................................................. 7 1.1 general considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 6

    Table of contents 8.2 input selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 8.3 advanced settings. ...

  • Page 7

    Table of contents 10.5.1 load layout file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 10.5.2 rename layout file . . . ....

  • Page 8

    Table of contents 13. Projector control ................................................................................................ 293 13.1 projector control menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 9

    Table of contents 16. Removal and installation of the projector covers ......................................................... 391 16.1 removal of the front cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 10

    Table of contents 6 r5905158 hdf series 08/12/2016.

  • Page 11: 1. Safety

    1. Safety 1. Safety about this chapter read this chapter attentively. It contains important information to prevent personal injury while installing and using a hdf series projector. Furthermore, it includes several cautions to prevent damage to the hdf series projector. Ensure that you understand an...

  • Page 12

    1. Safety 1.1 general considerations w arning : ensure you understand and follow all the safety guidelines, safety instructions, warnings and cautions mentioned in this manual. W arning : be aware of suspended loads. W arning : wear a hard hat to reduce the risk of personal injury. W arning : be car...

  • Page 13

    1. Safety 1.2 important safety instructions to prevent the risk of electrical shock • this product should be operated from a mono phase ac power source. • this apparatus must be grounded (earthed) via the supplied 3 conductor ac power cable. If none of the supplied power cables are the correct one, ...

  • Page 14

    1. Safety to prevent personal injury • isolate electrically before replacing the lamp or lamp house. Caution: hot lamp (house). • caution: high pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel. • to prevent injury and physical damage, always read this m...

  • Page 15

    1. Safety to prevent projector damage • this projector has been designed for use with a specific lamp (house) type. See installation instructions for its correct type. • the air filters of the projector must be cleaned or replaced on regular base (a "clean" booth would be monthly-minimum). Neglectin...

  • Page 16

    1. Safety to prevent battery explosion • danger of explosion if battery is incorrectly installed. • replace only with the same or equivalent type recommended by the manufacturer. • for disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and ...

  • Page 17

    1. Safety 1.3 light beam hazard distance (hd) hd light beam hazard distance (hd) is the distance from the source at which the intensity or the energy per surface unit becomes lower than the applicable safety limit. The light beam can thus be considered as dangerous if the operator is closer from the...

  • Page 18

    1. Safety pr image 1-2 14 r5905158 hdf series 08/12/2016.

  • Page 19

    1. Safety 1.4 hd in function of the lens throw ratio (tr) tr (throw ratio) the ratio of the distance to the screen (throw) to the screen width. Hdf series projector hazard distance 0 1 2 3 4 5 6 7 8 9 10 11 12 13 0,5 1,3 2,0 2,8 3,5 4,3 5,0 5,8 6,5 7,3 8,0 8,8 9,5 10,3 11,0 11,8 12,5 13,3 14,0 hd [m...

  • Page 20

    1. Safety 1.5 important warnings concerning hdf series flight cases important warnings concerning stacking/transporting hdf series rental flight cases • stack maximum two (2) hdf series rental flight cases high. Never higher. • surface on which flight case is standing must be level to ensure that th...

  • Page 21: Restrictions

    2. Configurations, requirements and restrictions 2. Configurations, requirements and restrictions about this chapter read this chapter before installing your hdf series projector. It contains important information concerning installation requirements and restrictions for the hdf series projector, su...

  • Page 22

    2. Configurations, requirements and restrictions 2.1 installation requirements environment conditions table below summarizes the physical environment in which the hdf series projector may be safely operated or stored. Environment operating non-operating ambient temperature 10 °c (50 °f) to 40 °c (10...

  • Page 23

    2. Configurations, requirements and restrictions 2.2 unpacking the projector what has to be done ? At delivery the projector is packed in a carton box upon a wooden pallet and secured with banding and fastening clips. Furthermore, to provide protection during transportation, the projector is surroun...

  • Page 24

    2. Configurations, requirements and restrictions image 2-3 5. Remove the wooden plate from the projector bottom, by releasing the four bolts. Use an 8 mm allen key. See image 2-3. 6. Gently turn the projector back on its feet. 7. Remove the foam rubber around the carrying handle. Save the original s...

  • Page 25

    2. Configurations, requirements and restrictions 2.3 hdf series flight case introduction of the hdf series flight case the hdf series flight case is designed to transport the hdf series projector in a safe and secure manner. The four caster wheels, provided with breaks, and the eight handles make th...

  • Page 26

    2. Configurations, requirements and restrictions 2.4 projector configurations the drawings used in this chapter are not contractual. For convenience some options available in the hdf series projectors (e.G. Standalone cooling unit in the laser version), are not shown here. The different configuratio...

  • Page 27

    2. Configurations, requirements and restrictions positioning the projector floor screen screen pd a cd screen sw sw sh b sh b cd image 2-8 projector positioning the projector should be installed at right angles (horizontally and vertically) to the screen at a distance pd. Note the distance (a) betwe...

  • Page 28

    2. Configurations, requirements and restrictions u +120% -20% -50% +50% d l r p f u d side view p f +120% -20% top view p f l r -50% +50% image 2-9 vertical and horizontal shift range p dmd. F field of view. It is mechanical possible to shift outside the recommended field of view, but it will result...

  • Page 29

    2. Configurations, requirements and restrictions 2.5 projector air inlets and outlets air inlets and outlets image 2-11 airflow the hdf series has 5 air inlet channels and one air outlet. The air outlet is located at the rear of the projector. The air inlets are located at the front, bottom, top and...

  • Page 30

    2. Configurations, requirements and restrictions 2.6 free download of projector toolset about projector toolset projector toolset is a software tool to set up, configure, manage and control barco projectors. The concept of this projector toolset software is modular. The basic package can be extended...

  • Page 31

    2. Configurations, requirements and restrictions 2.7 installation process overview quick setup the following steps describe briefly how to setup your hdf series projector in a table mount front projection. Note that each step refers to a corresponding procedure, which is more detailed and illustrate...

  • Page 32

    2. Configurations, requirements and restrictions 28 r5905158 hdf series 08/12/2016.

  • Page 33: 3. Physical Installation

    3. Physical installation 3. Physical installation about this projector this chapter describes how the mechanical set up of the projector has to be done and how to realize the electrical connections. Overview • remote control unit (rcu) • lenses • power connection • suspension of the hdf series proje...

  • Page 34

    3. Physical installation 3.1 remote control unit (rcu) introduction the remote control unit (a) of the hdf series projector is equipped with a rugged case (b) and an xlr adaptor (c). The remote control unit can be used wired via mini-jack or via rugged xlr. Note that the backlight, of the remote con...

  • Page 35

    3. Physical installation 3.1.1 rcu battery installation where to find the batteries for the remote control ? The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life time. At delivery the batteries can be found in a separa...

  • Page 36

    3. Physical installation 3.1.2 rcu rugged case installation how to install the rugged case of the remote control ? 1. Slide the bottom of the rcu into the rugged case and then pull the top of the rugged case over the top of the rcu as illustrated. Image 3-5 32 r5905158 hdf series 08/12/2016.

  • Page 37

    3. Physical installation 3.1.3 rcu xlr adaptor installation install the rugged case before installing the xlr adaptor. Vice-versa, remove the xlr adaptor before removing the rugged case from the rcu. Necessary tools 5 mm flat screw driver. How to install the xlr adaptor of the remote control unit ? ...

  • Page 38

    3. Physical installation 3.1.4 using the xlr adaptor of the rcu how to use the xlr adaptor of the remote control unit ? 1. Connect a cable with xlr plug into the xlr adaptor. 2. Connect the other end of the cable with your hdf series projector. 3. Push the xlr adaptor completely against the rugged c...

  • Page 39

    3. Physical installation 3.1.5 rcu usage possibilities summarized possibilities ref. Possibility description comment a. Rcu not wired b. Rcu wired (mini-jack) backlight illuminates continuously when wire is connected. Infra red disabled. C. Rcu with rugged case not wired d. Rcu with rugged case wire...

  • Page 40

    3. Physical installation 3.2 lenses overview • available lenses • lens selection • lens installation • lens removal • lens safety cable • lens shift, zoom & focus • scheimpflug adjustment 36 r5905158 hdf series 08/12/2016.

  • Page 41

    3. Physical installation 3.2.1 available lenses available lenses for the hdf series projector image 3-9 r9801414: tld+ zoom lens (0.8 - 1.16 : 1) image 3-10 r9840776: tld+ (1.16 : 1) fixed lens image 3-11 r9862000: tld+ lens (0.67 : 1) image 3-12 r9862005: tld+ zoom lens (1.16 - 1.49 : 1) image 3-13...

  • Page 42

    3. Physical installation 3.2.2 lens selection how to select the right lens 1. Determine the required screen width (sw). 2. Determine the approximate position of the projector in the room. 3. Start up the lens calculator on the barco website: https://www.Barco.Com/en/media_entertainment/lenscalculato...

  • Page 43

    3. Physical installation 3.2.3 lens installation how to install 1. Remove the plastic cap in the opening of the lens holder if not removed yet. 2. Take the lens assembly out of its packing material and remove the lens caps on both sides. 3. Place the lens holder in the “unlocked” position by moving ...

  • Page 44

    3. Physical installation image 3-21 lock lens 8. Check if the lens is really secured by trying to pull the lens out of the lens holder. 40 r5905158 hdf series 08/12/2016.

  • Page 45

    3. Physical installation 3.2.4 lens removal how to remove 1. Support the lens with one hand while you unlock the lens holder by sliding the lock handle towards the “unlocked” position as illustrated. Image 3-22 lens removal, unlock 2. Gently pull the lens out of the lens holder. Image 3-23 lens remo...

  • Page 46

    3. Physical installation 3.2.5 lens safety cable when using the safety cable ? The lens safety cable must be used in any circumstances to protect a mounted lens in the lens holder. Configuration differences there are two different configurations for the safety cable. The configuration used depends o...

  • Page 47

    3. Physical installation image 3-26 example of configuration a 5. Install a u-bolt on the lens holder, with the open ends oriented outwards (reference 3). Make sure that both a part of the loop end and the outgoing part of the safety cable are placed in the enclosure. 3 image 3-27 example of configu...

  • Page 48

    3. Physical installation image 3-29 example using the bottom carrying handle image 3-30 example using the hoisting eye 44 r5905158 hdf series 08/12/2016.

  • Page 49

    3. Physical installation 3.2.6 lens shift, zoom & focus via lens key 1. Press lens key on the local keypad or the remote control. The zoom/focus menu opens. Image 3-31 zoom/focus adjustment 2. Use the ▲ or ▼ key to zoom the lens. Use the ◄ or ► key to focus the lens. Press enter to switch to lens sh...

  • Page 50

    3. Physical installation 3.2.7 scheimpflug adjustment always use allowed and calibrated lenses for the specific projector while adjusting the scheimplug adjust- ments. What has to be done ? The lens holder has to be adjusted so that the “sharp focus plane” of the projected image falls together with ...

  • Page 51

    3. Physical installation 1, 2 and 3 are adjustment points. 4 is a locking point and not used during scheimpflug adjustment. Necessary tools • allen key 3 mm • nut driver 13 mm • nut driver 10 mm how to adjust 1. Project a green focus pattern. Image 3-35 2. Loosen the lock nuts (a, b, c and d). See i...

  • Page 52

    3. Physical installation 1 2 3 f image 3-36 center focusing 6. Sharpen bottom left corner of the screen by adjusting nut 1. 1 f image 3-37 left bottom focusing 7. Sharpen bottom right corner of the screen by adjusting nut 2. 48 r5905158 hdf series 08/12/2016.

  • Page 53

    3. Physical installation 2 f image 3-38 right bottom focusing 8. Sharpen top right corner of the screen by adjusting nut 3 3 f image 3-39 corner focusing 9. Repeat from step 6 until the projected focus pattern is as sharp as possible in the center, left, right, top and bottom of the screen. How to f...

  • Page 54

    3. Physical installation 1/3 to 1/2 image 3-40 4. Fasten lock nut d. 5. Tighten nut 4 until the offset of the image movement created in step 3 is canceled. Tip: the amount of image movement in step 3 will determine how tight the nut in step 5 will need to be turned to return the image to its origina...

  • Page 55

    3. Physical installation 3.3 power connection c aution : use only the power cord provided with the projector. How to connect your projector with the local power net ? 1. Ensure that the power switch (s) stands in the “0” (off) position. 2. Connect the power cord (p) with the power input socket of th...

  • Page 56

    3. Physical installation 3.4 suspension of the hdf series projector with rigging clamps rigging points and rigging clamps the carrying handle, at the bottom side of the projector, is provided with eight slots. Four slots are longitudinally (a) oriented and four slots are transversely (b) oriented. E...

  • Page 57

    3. Physical installation a b b image 3-46 mounting clamps 4. Place all four rigging clamps in open position as illustrated. Image 3-47 opening clamps 5. Place the projector (upside down) under the truss installation and lower the truss until the support bars of the truss are nearby the rigging clamp...

  • Page 58

    3. Physical installation s s image 3-49 mounting safety chains warning: install the safety chain in that way that the projector cannot drop more than 20 cm. 9. Lift up the truss with attached projector to the desired height. Proceed with the alignment procedure, see "alignment of a ceiling mount hdf...

  • Page 59: 4. Input & Communication

    4. Input & communication 4. Input & communication overview • introduction • input source connections • communication connections r5905158 hdf series 08/12/2016 55.

  • Page 60

    4. Input & communication 4.1 introduction general the input & communication side of the projector consists of a button module, a dual 3g/hdsdi and dvi-i input as standard input module and 2 free input slots. The free input slots can be used for optional modules (e.G. 5-cable input). 1 2 3 4 5 6 7 9 ...

  • Page 61

    4. Input & communication 4.2 input source connections dvi and 3g/hdsdi input this input module is standard delivered with the hdf series projector. Dual link dvi-i hdcp input sel sync 3g/dual hdsdi out1 in1 in2 out2 sel sync sel sync r9864000 image 4-2 dual link dvi and 3g/dual hdsdi input the yello...

  • Page 62

    4. Input & communication • data and hd sources rgb and yuv [hs/vs, cs or sog(y)]: - pixel clock maximum 210 mhz - 8 bit digital output • video sources cvbs, s-video, rgb and yuv [cs, cv or sog(y)]: - pal b/d/i/g/h, pal60, pal m, pal n, pal nc - ntsc m/j, ntsc 4.43 - secam b/d/g/k/l - 525i, 625i, 525...

  • Page 63

    4. Input & communication • hdmi (high-definition multimedia interface) hdmi 1.4a up to 210mhz pixel clock. Support for ‘deep color’ up to 12 bit per color. • displayport displayport 1.1a up to 210 mhz pixel clock. Support for ‘deep color’ up to 12 bit per color. In all cases, the minimum input frequ...

  • Page 64

    4. Input & communication 4.3 communication connections communication interface 12v /1a in dmx out remote ctrl rs232/422 in usb 10/100 base-t eth act pwr lmp 10/100 err ir act wifi sel 1 2 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 image 4-5 communication interface, indications 1 12v 1a output 2 dmx inter...

  • Page 65

    4. Input & communication wired remote control (xlr) if desired the remote control unit can be wired and plugged in into the male xlr port on the communication interface. Xlr – remote ctrl in pin description 1 gnd 2 rc5 in 3 xlr present sense rs232/rs422 input the communication interface of the hdf s...

  • Page 66

    4. Input & communication rs422 an eia serial digital interface standard that specifies the electrical characteristics of balanced (differential) voltage, digital interface circuits. This standard is usable over longer distances than rs-232. This signal governs the asyn- chronous transmission of comp...

  • Page 67: 5. Getting Started

    5. Getting started 5. Getting started overview • rcu & local keypad • terminology overview • power on projector • switching to standby • power off projector • status leds • using the rcu • projector address • source selection • alignment of a table mount hdf series projector • alignment of a ceiling...

  • Page 68

    5. Getting started 5.1 rcu & local keypad how controlling the projector ? The projector can be controlled by the local keypad or by the remote control unit. Location of the local keypad ? The local keypad is located on the input side of the projector. Remote control functions. This remote control in...

  • Page 69

    5. Getting started 5.2 terminology overview overview the following table gives an overview of the different functionality of the keys. Menu exit enter pause text phase tint color brightn contr 9 0 7 8 5 6 3 4 1 2 lens lens zoom lens shift lens focus sharpn lens shift 5 * % 3$ 7 7( 51 3 ,3 : ,1 '2 : ...

  • Page 70

    5. Getting started ind. Key name description 13 picture controls use these buttons to obtain the desired picture level. 14 phase used to remove the horizontal instability of the image (usually for rgb source). It adjusts the phase of the pixel sampling clock relative to the incoming signal. 15 freez...

  • Page 71

    5. Getting started 5.3 power on projector how to power on. 1. Press the power switch at the back of the projector to switch on this projector. Image 5-2 main switch - when ’0’ is pressed, the projector is switched off. - when ’1’ is pressed, the projector is switched on. The projector starts up in s...

  • Page 72

    5. Getting started image 5-3 local screen, lamp • number of strikes • run time in hours • remaining run time in hours • slide bar indication with percentage indication of the current run time, compared with the maximum life time of the lamp. Software overview once the projector is started, press abo...

  • Page 73

    5. Getting started menu exit enter pause text phase tint color brightn contr 9 0 7 8 5 6 3 4 1 2 lens lens zoom lens shift lens focus l sharpn lens shift 1 2 3 4 5 6 7 8 9 0 menu exit enter rgb stby pause text pattern window pip lens rigging auto a b image 5-5 stand by indication a stand by indicati...

  • Page 74

    5. Getting started 5.4 switching to standby how to switch to standby 1. Press and hold standby for 3 seconds on the local keypad or the remote control. In the mean time the message keep on pressing... Is displayed. This message changes to saving data ... The projector goes to standby. All custom set...

  • Page 75

    5. Getting started 5.5 power off projector how to power off 1. Press first standby. 2. Let cool down the projector until the fan speed decreases. At least 5 minutes. 3. Switch off the projector with the power switch. ’0’ must be pressed. C aution : never switch off the projector while the message ’s...

  • Page 76

    5. Getting started 5.6 status leds overview led color status description red on projector is in standby red toggles on/off projector startup failed, no lamp power supply green toggles on/off projector starts up green on projector is on white toggles on/off from/to eco standby dimmed white projector ...

  • Page 77

    5. Getting started 5.7 using the rcu pointing to the reflective screen 1. Point the front of the rcu to the reflective screen surface. F1 f2 f3 f4 f5 ad j ex it en te r pa us e ph as e te xt sh ar pn ti nt co lo r br ig ht n co nt r tr eb le ba la nc e ba ss vo l 9 0 7 8 5 6 3 4 1 2 image 5-6 ir con...

  • Page 78

    5. Getting started 5.8 projector address 74 r5905158 hdf series 08/12/2016.

  • Page 79

    5. Getting started 5.8.1 displaying and programming addresses into the rcu displaying the projector address on the screen. 1. Press address key (recessed key on the rcu) with a pencil. The projector’s address is displayed on the local lcd screen. To continue using the rcu with that specific address,...

  • Page 80

    5. Getting started 5.8.2 controlling the projector projector address address installed in the projector to be individually controlled. Common address projector will always execute the command coming from a rcu programmed with that common address. Why a projector address ? As more than one projector ...

  • Page 81

    5. Getting started 5.9 source selection source selection when no picture in picture is active use the digit keys on the remote control or local keypad to activate the desired source. Source selection when picture in picture is active use the window button on the remote control or the local keypad to...

  • Page 82

    5. Getting started 5.10 alignment of a table mount hdf series projector how to align a table mount hdf series projector ? 1. Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen. 2. Project one of the internal hatch patterns on the...

  • Page 83

    5. Getting started 5.11 alignment of a ceiling mount hdf series projector necessary tools 17 mm open ended spanner. How to align 1. Install the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen. 2. Project one of the internal hatch patter...

  • Page 84

    5. Getting started 80 r5905158 hdf series 08/12/2016.

  • Page 85

    6. Quick set up adjustment 6. Quick set up adjustment overview • text boxes on or off • quick lens adjustment via lens key • direct lens adjustment (rcu) • quick picture in picture • quick language selection r5905158 hdf series 08/12/2016 81.

  • Page 86

    6. Quick set up adjustment 6.1 text boxes on or off text toggle function the on-screen text boxes can be switched off so that an adjustment during the operation of the projector is not visible on the screen. The adjustment indication remains visible on the local lcd screen. 1 2 3 4 5 6 7 8 9 0 menu ...

  • Page 87

    6. Quick set up adjustment 6.2 quick lens adjustment via lens key quick zoom/focus adjustment 1. Press the lens key on the remote control or local keypad to open the zoom/focus adjustment menu. 1 2 3 4 5 6 7 8 9 0 menu exit enter rgb stby pause text pattern window pip lens auto f n menu exit enter p...

  • Page 88

    6. Quick set up adjustment image 6-5 shift adjustment 3. Use the ▲ or ▼ key to shift the lens in vertical direction. Use the ◄ or ► key to shift the lens in horizontal direction. Press enter to switch to zoom/focus adjustment. 84 r5905158 hdf series 08/12/2016.

  • Page 89

    6. Quick set up adjustment 6.3 direct lens adjustment (rcu) lens adjustment buttons on the remote control on the remote control four buttons with double action are provided, allowing direct alignment for lens zoom, focus, horizon- tal shift and vertical shift. 1. Press lens zoom button [-] or [+] (a...

  • Page 90

    6. Quick set up adjustment 6.4 quick picture in picture quick on - off press on the pip key on the remote control or the local keypad to activate the load layout window. Use the ▲ ▼ key to scroll to the desired layout and press enter to activate. Select main full screen to switch off pip. Image 6-7 ...

  • Page 91

    6. Quick set up adjustment 6.5 quick language selection quick language selection via the remote control when no osd menu is visible on the screen, press the info button (1) on the remote control. Menu exit enter 5 * % 3$ 7 7( 51 3 ,3 : ,1 '2 : 1 image 6-8 info button the language selection menu is d...

  • Page 92

    6. Quick set up adjustment image 6-10 main menu, projector control image 6-11 projector control, change language image 6-12 language selection 88 r5905158 hdf series 08/12/2016.

  • Page 93

    7. Start up of the adjustment mode 7. Start up of the adjustment mode overview • about the adjustment mode • about the use of the remote control and the local keypad • start up the adjustment mode • navigation and adjustments • menu memory • shortcut keys to the menus • test patterns in adjustment m...

  • Page 94

    7. Start up of the adjustment mode 7.1 about the adjustment mode overview as the adjustment mode is the central place to control and align the projector, the following functions can be done: • input setup: different input settings can be adjusted such as specific input slot settings, locking, native...

  • Page 95

    7. Start up of the adjustment mode 7.2 about the use of the remote control and the local keypad overview all navigations and adjustments can be done either with the remote control or with the local keypad. Almost all the keys on the remote control have an equivalent on the local keypad. Exceptions: ...

  • Page 96

    7. Start up of the adjustment mode 7.3 start up the adjustment mode start up tools to start up the adjustment mode, use the remote control or the local keypad. How to start up? 1. Press menu on the remote control (rcu) or on the local keypad to start up the adjustment mode. The main menu of the adju...

  • Page 97

    7. Start up of the adjustment mode 7.4 navigation and adjustments how to navigate in the menu structure? Once in the menu structure, use the ▲ or ▼ key on the remote control or on the local keypad to scroll through the items in the displayed menu. The selected item will get a background color. To ac...

  • Page 98

    7. Start up of the adjustment mode 7.5 menu memory overview each menu with sub menus, remembers its last selected sub item even when leaving the menu structure and that as long as the projector is running. When restarting the projector from stand-by, the menu memory is reset. After re-opening the ma...

  • Page 99

    7. Start up of the adjustment mode 7.6 shortcut keys to the menus about a shortcut key the digit keys 5 to 9 can be customer programmed to directly open a pre-stored menu. That menu can be any independent menu out of the list of menus. A menu which is built up by the content of a previous menu canno...

  • Page 100

    7. Start up of the adjustment mode 7.7 test patterns in adjustment mode overview when the adjustment mode is started, a test pattern can be called at any moment just by pressing the pattern key on the rcu or the local key path. Press as many times on the pattern key as necessary to display the desir...

  • Page 101

    7. Start up of the adjustment mode 7.8 help information in adjustment mode overview for many items in the adjustment mode, help information is available. When on an item, just click on the info button of your remote control to display information about the selected item. Menu exit enter 5 * % 3$ 7 7...

  • Page 102

    7. Start up of the adjustment mode 98 r5905158 hdf series 08/12/2016.

  • Page 103: 8. Input

    8. Input 8. Input overview • input menu overview • input selection • advanced settings • input locking • minimum delay • native resolution • no signal • edid • 3d input in all cases, the minimum input frequency for 3d is 23 hz per eye. Below this frequency the image will not be displayed correctly. ...

  • Page 104

    8. Input 8.1 input menu overview overview table level 1 level 2 level 3 level 4 input input selection dvi/rgb sdi (sd/hd/3g/dual) optional input 1 optional input 2 advanced settings dvi/rgb dvi dvi dual link rgb hs-vs yuv hs-vs auto sdi (sd/hd/3g/dual) input 1 priority input 2 priority input 1 input...

  • Page 105

    8. Input line alternating (3g) second input r5905158 hdf series 08/12/2016 101.

  • Page 106

    8. Input 8.2 input selection how to select 1. Press menu to activate the menus and select input → input selection. 2. Press enter. The select source menu is displayed with the actual available sources filled out. 3. Use the ▲ or ▼ key to select an input. Image 8-1 main window image 8-2 input selecti...

  • Page 107

    8. Input 8.3 advanced settings overview • about input setup • input configuration • dvi - rgb input • sdi input • 5 cable input • hdmi - displayport input (3d input module) r5905158 hdf series 08/12/2016 103.

  • Page 108

    8. Input 8.3.1 about input setup overview each input module must be configured before these module can be used. This configuration is necessary so that the projector knows which type of signal is connected to its input. The projector has 4 input slots. Slot 1 and 2 is filled up by default with a dvi...

  • Page 109

    8. Input 8.3.2 input configuration 3d item in the input menu is grayed out when no 3d module is inserted in slot 3 or 4. How to change? 1. Press menu to activate the menus and select input → advanced settings. 2. Press enter. The advanced settings window is displayed with the actual situation filled...

  • Page 110

    8. Input 8.3.3 dvi - rgb input how to select select dvi / rgb and press enter to open the selections image 8-7 dvi selection the following selections are possible: • dvi • dvi - dual link • rgb hs-vs/cs • yuv hs-vs/cs • auto dvi will not natively support 10-bit or 12-bit deep color. It is possible t...

  • Page 111

    8. Input 8.3.4 sdi input about sdi input the dual sd/hd/3g-sdi input can accept standard-definition (sd), high-definition (hd) and 3 gigabit-definition serial-digital-inter- face (sdi) signals . How to select select sdi (sd / hd / 3g / dual) and press enter to open the selections image 8-9 sdi, inpu...

  • Page 112

    8. Input 3g-a and 3g-b: • direct mapping (3g-a) • dual hd (3g-b) when dual hd is selected, it is possible to use swap links. If swap links must be used, use the ▲ or ▼ key to select and press enter to accept. The check box will be checked. Dual hd : • swap links 108 r5905158 hdf series 08/12/2016.

  • Page 113

    8. Input 8.3.5 5 cable input how to select select 5 cable and press enter to open the selections image 8-11 advanced settings, 5-cable image 8-12 5 cable configuration use the ▲ or ▼ key to select the desired configuration and press enter to select. When e.G. Cvbs/s-video auto is selected, the proje...

  • Page 114

    8. Input 8.3.6 hdmi - displayport input (3d input module) how to select select hdmi/dp and press enter to open the selections image 8-13 hdmi-display port selection use the ▲ or ▼ key to select the desired input and press enter to select. 110 r5905158 hdf series 08/12/2016.

  • Page 115

    8. Input 8.4 input locking what is possible? The output signal can be locked on an internal sync signal or on the sync signal of one of the input sources. Or it can follow the input of the main window or pip window. When locked to the corresponding input sync, the output will be shown without moveme...

  • Page 116

    8. Input when input locking is set to a specific input and there is no sync signal available, the locking will be switched to free run without changing the user settings. Once the sync is available, it applies again the user settings. Options for free run when free run is selected, radio button sele...

  • Page 117

    8. Input 8.5 minimum delay purpose the minimum delay only affects the de-interlacing. In case of interlaced sources, the de-interlacer will be bypassed and the image will be shown with line interpolation applied. To ensure minimum delay in the other processing steps, make sure warping is off, the re...

  • Page 118

    8. Input 8.6 native resolution what can be done the aim here is to always show the resolution of the source independently of the resolution of the dmd panels. When the resolution of the source is exactly the resolution of the dmd panels, then the full content will be shown on the full dmd (a). When ...

  • Page 119

    8. Input image 8-22 main menu image 8-23 input, native resolution r5905158 hdf series 08/12/2016 115.

  • Page 120

    8. Input 8.7 no signal overview • background color • background logo • shutdown settings • shutdown retarding time • auto dimming what can happen when no signal when no signal is available at the selected input, the output can be set to blue or black or a personal defined logo can be displayed or th...

  • Page 121

    8. Input 8.7.1 background color how to set the background color 1. Press menu to activate the menus and select input → no signal. → color. 2. Press enter to toggle between [blue] or [black]. Image 8-24 main menu image 8-25 input, no signal image 8-26 no signal, color r5905158 hdf series 08/12/2016 1...

  • Page 122

    8. Input 8.7.2 background logo what can be done ? A logo can be switched on or off. When logo is switched on and a logo is available, that logo will be displayed when no signal is available for the main window an no signal available for the pip window in case pip is on. How to activate logo 1. Press...

  • Page 123

    8. Input 8.7.3 shutdown settings how to change the settings 1. Press menu to activate the menus and select input → no signal. → shutdown. Image 8-30 main menu image 8-31 input, no signal image 8-32 no signal, shutdown 2. Press enter to toggle between [on] and [off]. [on] : projector goes in shutdown...

  • Page 124

    8. Input 8.7.4 shutdown retarding time about the shutdown retarding time the retarding time is the time between no signal is detected and the moment that the projector shuts down. How to set the retarding time 1. Press menu to activate the menus and select input → no signal. → shutdown time (min). I...

  • Page 125

    8. Input 8.7.5 auto dimming about auto dimming when no signal is detected on the selected input the lamp power will be reduced from the current value to its minimum value. When the input signal is re-detected, the lamp power is restored to its original value. How to set up 1. Press menu to activate ...

  • Page 126

    8. Input 8.8 edid edid extended display identification data about edid the edid file available for dvi input connectors includes timings supported by the projector; display size and other information about the display (i.E. Projector). It is the set of information that is used by digital sources con...

  • Page 127

    8. Input 8.8.1 configure an input description selecting the standard edid file or an own created file can be selected from the list of custom edid files for the input. How to configure 1. Press menu to activate the menus and select input → edid → configure. 2. Press enter to open the edid configurat...

  • Page 128

    8. Input 8.8.2 create custom edid file description you can create new custom edid files and enter the desired input timings. How to create 1. Press menu to activate the menus and select input → edid → create. 2. Press enter to open the edid creation menu. Image 8-44 main menu image 8-45 input, edid ...

  • Page 129

    8. Input if necessary, scroll down to see extra options. Select or clear the check boxes. Image 8-48 edid file creation, options the following options are possible: - stereo: this check box is currently not in use. You can leave it unchecked. - deep color: select this box in case of a 12 bit color s...

  • Page 130

    8. Input 8.8.3 delete a custom edid file standard edid files cannot be deleted. How to delete 1. Press menu to activate the menus and select input → edid → delete. 2. Press enter to open the edid list with custom files. Image 8-49 main menu image 8-50 input, edid image 8-51 edid, delete 3. Use the ▲...

  • Page 131

    8. Input 8.8.4 delete all custom edid file standard edid files cannot be deleted. How to delete 1. Press menu to activate the menus and select input → edid → delete all. 2. Press enter to open the confirmation window. Image 8-54 main menu image 8-55 input, edid image 8-56 delete all image 8-57 delet...

  • Page 132

    8. Input 8.9 3d input overview • about 3d modes • activate 3d • auto detection • input type selection • 3d second input • l-r synchronisation, field dominance • l-r synchronisation, invert 3d sync out 128 r5905158 hdf series 08/12/2016.

  • Page 133

    8. Input 8.9.1 about 3d modes the mentioned menu items in the mode explanation will be explained in detail in the next topics. Settings in the 3d menu are stored per input. Single 3d channel - full resolution - sequential mode content is displayed by one 3d source. The frames for the left eye and ri...

  • Page 134

    8. Input the 3d input module is activated for dual 3d channel: menu > input > 3d > frame sequential – dual channel possible sources: 2 x dvi , 2 x sdi. If two 3d input modules are installed: 2 x hdmi or 2 x displayport. Sensio ® hi-fi 3d 1 2 1 2 3 4 3 4 2 1 2 1 4 3 4 3 1 1 2 2 3 3 4 4 1 1 2 2 3 3 4 ...

  • Page 135

    8. Input dvi/hdmi/dp 5–cable analog dvi analog sdi fpix ≤ 210 mhz fpix ≤ 210 mhz fpix ≤ 170 mhz fpix ≤150 mhz hd formats only. Max. Resolution: 1920x1080@30hz or 1280x720@60hz. Hd formats only. Max. Resolution: 1920x1080@30hz or 1280x720@60hz. Hd formats only. Max. Resolution: 1920x1080@30hz or 1280...

  • Page 136

    8. Input 8.9.2 activate 3d what can be done ? The status of the 3d function can be enabled or disabled. This function is input dependent. How to enable/disable 1. Press menu to activate the menus and select input → 3d → status. Image 8-59 main menu image 8-60 input, 3d image 8-61 3d status 2. Press ...

  • Page 137

    8. Input 8.9.3 auto detection about auto detection • automatically detects the 3d format (frame packing, side-by-side, top-and-bottom) on hdmi sources, based on the content of the hdmi vendor specific infoframe (if present). For a detailed explanation of the hdmi vendor specific infoframe, refer to ...

  • Page 138

    8. Input image 8-64 3d, auto detection 134 r5905158 hdf series 08/12/2016.

  • Page 139

    8. Input 8.9.4 input type selection about input types • frame sequential - single channel : one input contains 3d information, alternating the left and the right information. • frame sequential - dual channel : two inputs, one contains the left eye information and the other contains the right eye in...

  • Page 140

    8. Input 8.9.5 3d second input what can be done? 3d content can be entered into the projector via a single channel (one input) or via 2 channels (2 inputs). When entering content via 2 channels, the second source must be indicated in the 3d menu. This selection is only possible when a 2 channel 3d i...

  • Page 141

    8. Input 8.9.6 l-r synchronisation, field dominance about field dominance the field dominance setting has only effect in the 3d mode: frame sequential - single channel (in all other modes this setting is grayed out). Furthermore, the input frequency must be equal or lower than 100 hz (50 hz per eye)...

  • Page 142

    8. Input 8.9.7 l-r synchronisation, invert 3d sync out what can be done? This menu allows to set the 3d emitter output signal. With invert 3d sync out we can swap the left and right 3d sync to eliminate a 3d output mismatch with the 3d emitters. Left 3d sync left right right inverted 3d sync left ri...

  • Page 143

    8. Input image 8-79 l/r synchronisation 2. Press enter. 3. Use the ▲ or ▼ key to select invert 3d sync out. Image 8-80 invert 3d sync out 4. Press enter to toggle between [on] and [off] [on] : 3d sync out is the inverted version of the 3d sync signal generated by the processing, allowing to swap lef...

  • Page 144

    8. Input 140 r5905158 hdf series 08/12/2016.

  • Page 145: 9. Image

    9. Image 9. Image overview • image menu overview • start up the image adjustments • image settings • aspect ratio • timings • image file services • save custom settings • splash image r5905158 hdf series 08/12/2016 141.

  • Page 146

    9. Image 9.1 image menu overview overview table level 1 level 2 level 3 level 4 image image settings contrast brightness saturation tint phase sharpness color temperature projector white computer 9300k video 6500k film 5400k broadcast 3200k custom balance input balance black balance white balance de...

  • Page 147

    9. Image options save custom settings splash image on or off timeout(sec) r5905158 hdf series 08/12/2016 143.

  • Page 148

    9. Image 9.2 start up the image adjustments start up 1. Press menu to activate the menus and select image image 9-1 main menu, image image 9-2 image adjustments 144 r5905158 hdf series 08/12/2016.

  • Page 149

    9. Image 9.3 image settings about image settings depending on the type of the connected source, some settings are grayed out image settings are stored per input. R5905158 hdf series 08/12/2016 145.

  • Page 150

    9. Image 9.3.1 contrast about contrast the contrast function is used to adjust the contrast between the light and the dark areas of the displayed image. It applies a gain to the red, green and blue signals. Contrast adjustment can be done with the contrast key on the rcu or via the menu structure. H...

  • Page 151

    9. Image 9.3.2 brightness about brightness the brightness function is used to adjust the black level in the input picture. It adds or subtracts an offset, or bias in to the red, green and blue signals. Brightness adjustment can be done with the brightness key on the rcu or via the menu structure. Ho...

  • Page 152

    9. Image 9.3.3 saturation about (color) saturation the saturation function is used to adjust the color saturation levels. Saturation adjustment can be done with the saturation key on the rcu or via the menu structure. How to adjust 1. Press menu to activate the menus and select image → image setting...

  • Page 153

    9. Image 9.3.4 phase about phase adjustment when displaying computer patterns or graphics (rgb or yuv signals) which are very detailed (tilting, vertical stripes, etc. ), jitter in picture (mis-sampling) may occur, causing horizontal stripes in portions of the screen. When this jitter occurs, adjust...

  • Page 154

    9. Image image 9-19 phase adjustment 3. To change the value directly in the image settings window, use the ◄ or ► key or a numeric key 0-9, to adjust as a % of the full range. To adjust via the bar scale menu, press enter to display the phase menu and adjust with the ◄ or ► key. Press enter again to...

  • Page 155

    9. Image 9.3.5 color temperature (fixed values) color temperature the coloration (reddish, white, bluish, greenish, etc.) of white in an image, measured using the kelvin (degrees k) temperature scale. Higher temperatures output more light. Projector white will provide maximum projector light output....

  • Page 156

    9. Image image 9-23 image settings, select color temperature depending on the color space setting, a request window is displayed to ask if the color space setting should be switched to off color temperature selection can only be done when the color space settings is set on off. Image 9-24 color temp...

  • Page 157

    9. Image 9.3.6 color temperature (custom values) how to set up 1. Press menu to activate the menus and select image → image settings → color temperature. Image 9-25 main menu, image image 9-26 image adjustments image 9-27 image settings, color temperature 2. Press enter to select. 3. Use the ▲ or ▼ ...

  • Page 158

    9. Image 9.3.7 input balance 154 r5905158 hdf series 08/12/2016.

  • Page 159

    9. Image 9.3.7.1 introduction to input balance introduction: unbalanced color signals when transporting signals, there is always a risk of deterioration of the information contained in the signals. In case of information contained in the amplitude of the signals which is the case of data color signa...

  • Page 160

    9. Image black level setting : brightness white level setting : contrast the same absolute black and white level for the three colors allows the same reference for brightness and contrast control of the picture ! These two references also set the range in which the adc will work for that particular ...

  • Page 161

    9. Image 9.3.7.2 adjusting the input balance how can it be done ? To balance the three color signals of a particular source there are conditions; in fact we must know the black and the white level of the source i.E. : 1. The source in question must be able to generate a white signal, ideally a 100% ...

  • Page 162

    9. Image image 9-36 image settings, input balance image 9-37 input balance, black 2. Press enter to select. 3. Do you want to use an internally generated test pattern ? If yes, use the ▲ or ▼ key to select adjustment pattern and press enter to toggle between [on] and [off] if no, adjust on the selec...

  • Page 163

    9. Image image 9-40 image settings, input balance image 9-41 input balance, white balance 3. Press enter to select. 4. Do you want to use an internally generated test pattern ? If yes, use the ▲ or ▼ key to select adjustment pattern and press enter to toggle between [on] and [off] if no, select a wh...

  • Page 164

    9. Image 9.3.8 image settings, defaults about the defaults with the defaults button, all image settings for a specific source are returned to the default values. How to return to the defaults 1. Press menu to activate the menus and select image → image settings → defaults. Image 9-42 main menu, imag...

  • Page 165

    9. Image 9.4 aspect ratio aspect ratio relation between the horizontal & vertical dimension in which the window will be displayed, e.G. 4 by 3 or 16 by 9. Can also be expressed as a decimal number, such as 1.77. The larger the ratio or decimal, the wider the image (or the less the image is squared)....

  • Page 166

    9. Image image 9-49 aspect ratio 4. Press enter to activate. How to set up the custom aspect ratio 1. While custom is selected, use the ▲ or ▼ key to select setup custom and press enter. Image 9-50 custom aspect ratio image 9-51 custom aspect ratio adjustment the custom aspect ratio setup menu opens...

  • Page 167

    9. Image 9.5 timings r5905158 hdf series 08/12/2016 163.

  • Page 168

    9. Image 9.5.1 source timings adjustable items • horizontal start in pixels : number of pixels between the horizontal sync and active video information in the input signal. • horizontal active = active horizontal pixels (width) : number of active pixels in the input signal. This value is normally gi...

  • Page 169

    9. Image 9.5.2 advanced timings, clamp delay - clamp width about the advanced settings clamp delay the time between the trailing edge of the sync pulse and the leading edge of the clamp pulse, in pixels. Can be any value between 0 and 255. Clamp width the width of the clamp pulse can be any value be...

  • Page 170

    9. Image image 9-59 clamp delay 3. Use the ▲ or ▼ key to select clamp delay or clamp width and use the ◄ or ► key to change the value. Or, press enter to open the specific adjustment menu. 166 r5905158 hdf series 08/12/2016.

  • Page 171

    9. Image 9.6 image file services r5905158 hdf series 08/12/2016 167.

  • Page 172

    9. Image 9.6.1 files and file manipulations connecting a new source. Source dependent adjustments like image settings, aspect ratio and timings are stored in a dedicated image file. Before using a new source, a correct image file has to be installed. The projector’s memory contains a list of files c...

  • Page 173

    9. Image 9.6.2 manual load file how to load 1. Press menu to activate the menus and select image → image file services → manual load. Image 9-60 main menu, image image 9-61 image, image file services image 9-62 image file services 2. Press enter to select. Depending on the file load filter setting a...

  • Page 174

    9. Image 9.6.3 file load filter about the filter setting depending on the load file filter, the load list can be reduced to the fitted files or can be expanded to show all files. [fit] : reduced list corresponding with the input source. [all] : full list with all available files in the projector. Ho...

  • Page 175

    9. Image 9.6.4 delete a file what can be done ? A custom image file can be deleted. Be aware that an active file can’t be deleted. How to delete 1. Press menu to activate the menus and select image → image file services → delete. Image 9-67 main menu, image image 9-68 image, image file services imag...

  • Page 176

    9. Image no recovery possible ! 172 r5905158 hdf series 08/12/2016.

  • Page 177

    9. Image 9.6.5 delete all custom files what can be done ? All custom image files can be deleted by executing a single command. Be aware that an active file can’t be deleted. Image files of active sources on input 1 to 4 cannot be deleted. How to delete 1. Press menu to activate the menus and select ...

  • Page 178

    9. Image 9.6.6 rename custom files a rename operation is only applicable for custom image files. How to rename 1. Press menu to activate the menus and select image → image file services → rename. Image 9-75 main menu, image image 9-76 image, image file services image 9-77 image file services, rename...

  • Page 179

    9. Image the rename window opens. Image 9-79 rename file 4. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next ch...

  • Page 180

    9. Image 9.6.7 copy custom file how to copy 1. Press menu to activate the menus and select image → image file services → copy. Image 9-80 main menu, image image 9-81 image, image file services image 9-82 image file services, copy 2. Press enter to select. The available custom files are displayed. Im...

  • Page 181

    9. Image the copy window opens. Image 9-85 copy custom files 4. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the nex...

  • Page 182

    9. Image 9.6.8 image file service options, load file how to set 1. Press menu to activate the menus and select image → image file services → options → load file. Image 9-86 main menu, image image 9-87 image, image file services image 9-88 image file services, options image 9-89 file options, load fi...

  • Page 183

    9. Image 9.6.9 image file service options, auto picture alignment how to set 1. Press menu to activate the menus and select image → image file services → options → auto picture alignment. Image 9-90 main menu, image image 9-91 image, image file services image 9-92 image file services, options image ...

  • Page 184

    9. Image 9.7 save custom settings what can be done ? The current custom settings can be saved to internal backup device in the same way as it would be done when the projector lamp was switched off. When settings are changed when the lamp is off, a manual save custom settings must be executed to save...

  • Page 185

    9. Image 9.8 splash image about a splash image when splash image is on, a dedicated image is displayed after start up and before the normal image is displayed and that for a certain time. A splash image can be uploaded via projector toolset. For more information about uploading a splash image, consu...

  • Page 186

    9. Image image 9-102 splash screen, time-out 3. Press enter to open the edit mode. Enter the time with 2 digits, e.G. 05 or 15. Note: maximum timeout = 15 seconds. Image 9-103 time-out, input 182 r5905158 hdf series 08/12/2016.

  • Page 187: 10. Layout

    10. Layout 10. Layout overview • layout menu overview • introduction • main window • pip window • layout file services • lens behavior r5905158 hdf series 08/12/2016 183.

  • Page 188

    10. Layout 10.1 layout menu overview overview table level 1 level 2 level 3 level 4 layout main window source size position pip window pip window [on], [off] source size position layout file services load main full screen native resolution pip up right split left right split top bottom custom x rena...

  • Page 189

    10. Layout 10.2 introduction overview layout files determine the size and the position of the main and pip window on the screen. Some pre-defined layouts are available in the projector but custom layouts can be created and saved for future use. A source number and lens settings can be associated wit...

  • Page 190

    10. Layout 10.3 main window overview • main window source selection • main window size • main window position when starting the main window settings, the system will ask to create a custom layout 186 r5905158 hdf series 08/12/2016.

  • Page 191

    10. Layout 10.3.1 main window source selection how to select 1. Press menu to activate the menus and select layout → main window → source. Image 10-1 main menu, layout image 10-2 layout, main window image 10-3 layout, main window image 10-4 main window, source 2. Press enter to select. The select so...

  • Page 192

    10. Layout 10.3.2 main window size what can be done? The size of the main window can be adjusted until the desired window dimensions are reached. Image 10-6 size adjustment main window a width adjustment b height adjustment the size can be changed with respect to the original aspect ratio by checkin...

  • Page 193

    10. Layout the size window opens. Image 10-10 size window 3. To keep the current aspect ratio, press enter to check lock. Once lock is checked, the width and the height will follow each other when changing one of the dimensions. 4. Use the ▲ or ▼ key to change the height and the ◄ or ► key to change...

  • Page 194

    10. Layout 10.3.3 main window position what can be done? The main window can be repositioned on the screen. The upper left corner is the reference. Image 10-12 positioning the window how to position 1. Press menu to activate the menus and select layout → main window → position. Image 10-13 main menu...

  • Page 195

    10. Layout a save layout window opens. Image 10-17 save layout 5. Use the ▲ or ▼ key to select yes and press enter to save. Select no if you want to quit without saving the current position. R5905158 hdf series 08/12/2016 191.

  • Page 196

    10. Layout 10.4 pip window overview • introduction to pip • picture in picture activation • pip window, source selection • pip window, size • pip window, position when starting the pip window settings, the system will ask to create a custom layout 192 r5905158 hdf series 08/12/2016.

  • Page 197

    10. Layout 10.4.1 introduction to pip pip pip stands for "picture in picture" and allows to display multiple windows containing each of them an image. The windows may be of the video or data type. What are the different possibilities within the pip mode ? The input section of the projector allows a ...

  • Page 198

    10. Layout 10.4.2 picture in picture activation how to activate 1. Press menu to activate the menus and select layout → pip window → pip window [on] / [off]. Image 10-19 main menu, layout image 10-20 layout, pip window image 10-21 pip window, activation 2. Press enter to toggle between [on] or [off]...

  • Page 199

    10. Layout 10.4.3 pip window, source selection how to select 1. Press menu to activate the menus and select layout → pip window → source. Image 10-22 main menu, layout image 10-23 layout, pip window image 10-24 pip window, source selection 2. Press enter to select. The select source window opens. Im...

  • Page 200

    10. Layout 10.4.4 pip window, size what can be done? The width and height of the picture in picture window can be changed till the desired dimensions are obtained. Image 10-26 size pip window a width pip window b height pip window the size of the picture in picture window can be changed with respect...

  • Page 201

    10. Layout image 10-30 pip window, size 2. Press enter to select. The size window opens. Image 10-31 pip window, resize 3. To keep the current aspect ratio, press enter to check lock. Once lock is checked, the width and the height will follow each other when changing one of the dimensions. 4. Use th...

  • Page 202

    10. Layout 10.4.5 pip window, position what can be done? The picture in picture window can be positioned on any place on the display just by changing its start coordinates. The reference is the upper left corner of the window. How to position 1. Press menu to activate the menus and select layout → p...

  • Page 203

    10. Layout 10.5 layout file services overview • load layout file • rename layout file • delete layout file • delete all layout files • copy or save as layout file r5905158 hdf series 08/12/2016 199.

  • Page 204

    10. Layout 10.5.1 load layout file when loading a layout that requires two sources, the pip window on/off setting will be switched to on. How to load file 1. Press menu to activate the menus and select layout → layout file services → load. Image 10-38 main menu, layout image 10-39 layout, layout fil...

  • Page 205

    10. Layout 10.5.2 rename layout file only custom created layouts can be renamed. How to rename 1. Press menu to activate the menus and select layout → layout file services → rename. Image 10-42 main menu, layout image 10-43 layout, layout file services image 10-44 layout file services, rename 2. Pre...

  • Page 206

    10. Layout 10.5.3 delete layout file only custom created layouts can be deleted. The current selected custom layout cannot be deleted. How to delete 1. Press menu to activate the menus and select layout → layout file services → delete. Image 10-46 main menu, layout image 10-47 layout, layout file se...

  • Page 207

    10. Layout 10.5.4 delete all layout files only custom layout files can be deleted. The current selected custom layout cannot be deleted. How to delete 1. Press menu to activate the menus and select layout → layout file services → delete all. Image 10-51 main menu, layout image 10-52 layout, layout f...

  • Page 208

    10. Layout 10.5.5 copy or save as layout file what can be done? The current loaded layout, custom layout or custom created layout, can be copied into a new file. How to copy / save as 1. Press menu to activate the menus and select layout → layout file services → copy/save as. Image 10-55 main menu, ...

  • Page 209

    10. Layout 10.6 lens behavior what can be done ? Different custom layouts can have different zoom/focus/shift (lens) settings, e.G. When using the projector on 2 different projector distances or two different screen sizes (same image but 2 custom layouts needed due to different zoom/focus/shift sett...

  • Page 210

    10. Layout during the calibration, a message is displayed. This message disappears when the calibration is finished. Image 10-63 lens calibration message 206 r5905158 hdf series 08/12/2016.

  • Page 211: 11. Lamp

    11. Lamp 11. Lamp overview • lamp menu overview • lamp power mode • lamp power • auto dimming when on pause • auto dimming when no signal • auto dimming when over-temperature • clo mode (constant light output mode) • clo targets • lps power • lamp identification • z-axis adjustment r5905158 hdf seri...

  • Page 212

    11. Lamp 11.1 lamp menu overview overview table level 1 level 2 level 3 lamp power power mode power auto dimming when pause auto dimming when no signal auto dimming when overtemperature clo mode clo targets lps power identification z-axis light output 208 r5905158 hdf series 08/12/2016.

  • Page 213

    11. Lamp 11.2 lamp power mode what can be done? The lamp power mode can be switched between normal, economic and long life. When playing in economic and long life mode, the lamp life time will be higher than in normal mode. The counter of the lamp life time counts equal for normal or economic mode b...

  • Page 214

    11. Lamp 11.3 lamp power what can be done? Within a certain power mode, the light output of the lamp can be reduced by reducing the lamp power how to reduce the power 1. Press menu to activate the menus and select lamp → power → power. Image 11-4 main menu, lamp image 11-5 lamp, power image 11-6 lam...

  • Page 215

    11. Lamp 11.4 auto dimming when on pause about auto dimming when on pause when the projector is switched to pause, the shutter is closed but the lamp is still running on full power. When auto dimming on pause is activated, then the lamp power will be reduced from its current value to its minimum val...

  • Page 216

    11. Lamp 11.5 auto dimming when no signal about auto dimming when no signal is detected on the selected input the lamp power will be reduced from the current value to its minimum value. When the input signal is re-detected, the lamp power is restored to its original value. This function is a duplica...

  • Page 217

    11. Lamp 11.6 auto dimming when over-temperature what can happen? When an over-temperature is detected, the projector starts dimming the lamp so that the projector can cool down. How to set up 1. Press menu to activate the menus and select lamp → power → auto dimming overtemperature. Image 11-13 mai...

  • Page 218

    11. Lamp 11.7 clo mode (constant light output mode) what can be done? Constant light output allows to force a constant light output (set in the clo target lumens item) of the projector over a certain period. This will eliminate uncontrolled light output drop caused by natural aging of the lamp. The ...

  • Page 219

    11. Lamp image 11-20 power, clo mode 2. Press enter to toggle between [on] or [off]. R5905158 hdf series 08/12/2016 215.

  • Page 220

    11. Lamp 11.8 clo targets what must be done? The light output target can be set. This value will force the projector to produce the target lumens when the clo mode is set to on. How to set the target 1. Press menu to activate the menus and select lamp → power → clo mode. Image 11-21 main menu, lamp ...

  • Page 221

    11. Lamp 11.9 lps power what is indicated ? The current lps power in watt is indicated as information. Image 11-24 lps power r5905158 hdf series 08/12/2016 217.

  • Page 222

    11. Lamp 11.10 lamp identification about the lamp identification menu gives an overview of the most important parameters of the used lamp. These parameters are: • serial number of the lamp • article number of the lamp • run time since first start up of the lamp • remaining run time for a safe operat...

  • Page 223

    11. Lamp 11.11 z-axis adjustment what can be done? The z-axis menu item gives the current light output of the projector (in percentage). This light output indication can be used to readjust the lamp position in the lamp casing (also called z-axis adjustment of the lamp). With higher run times, the l...

  • Page 224

    11. Lamp 220 r5905158 hdf series 08/12/2016.

  • Page 225: 12. Alignment

    12. Alignment 12. Alignment overview • alignment menu overview • orientation • lens adjustment, zoom - focus • lens adjustment, shift • lens adjustment, mid position • calbrate lens at startup • calibrate lens • warping • blanking adjustment • contrast-intensity • gamma • internal patterns • color s...

  • Page 226

    12. Alignment 12.1 alignment menu overview overview table level 1 level 2 level 3 alignment orientation front / table front / ceiling rear / table rear / ceiling auto front auto rear lens zoom / focus shift mid position calibrate lens at startup calibrate warping status warp adjust opacity warp file...

  • Page 227

    12. Alignment pan / tilt store setting per layout r5905158 hdf series 08/12/2016 223.

  • Page 228

    12. Alignment 12.2 orientation what can be done? The way of physical installation of the projector can be defined to the projector. The following installation are possible: • front/table • front/ceiling • rear/table • rear/ceiling • auto front : automatic front, projector detects itself if it is cei...

  • Page 229

    12. Alignment 12.3 lens adjustment, zoom - focus zoom/focus adjustment 1. Press menu to activate the menus and select alignment → lens. Image 12-4 main menu, alignment image 12-5 alignment, lens 2. Use the ▲ or ▼ key to select zoom/focus and press enter to activate. Image 12-6 lens, zoom/focus 3. Us...

  • Page 230

    12. Alignment 12.4 lens adjustment, shift how to shift lens 1. Press menu to activate the menus and select alignment → lens. Image 12-8 main menu, alignment image 12-9 alignment, lens 2. Use the ▲ or ▼ key to select shift and press enter to activate. Image 12-10 lens, shift 3. Use the ▲ or ▼ key to ...

  • Page 231

    12. Alignment 12.5 lens adjustment, mid position how to return to mid position 1. Press menu to activate the menus and select alignment → lens. Image 12-12 main menu, alignment image 12-13 alignment, lens 2. Use the ▲ or ▼ key to select mid position and press enter to activate. Image 12-14 lens, mid...

  • Page 232

    12. Alignment 12.6 calbrate lens at startup about calibrating lens each time the projector is started, a homing procedure (calibration) can be executed so that the projector exactly knows the lens position. How to calibrate 1. Press menu to activate the menus and select alignment → lens. Image 12-15...

  • Page 233

    12. Alignment 12.7 calibrate lens lens calibration is a time consuming operation. How to calibrate 1. Press menu to activate the menus and select alignment → lens. Image 12-18 main menu, alignment image 12-19 alignment, lens 2. Use the ▲ or ▼ key to select calibrate lens and press enter to activate....

  • Page 234

    12. Alignment 12.8 warping not all models are equipped with a warping unit. For these models, the warping unit is optional. Overview • about warping • warp activation - deactivation • start up manual adjustment • warp adjustment principle • setting the warping level • warp adaptation steps • making ...

  • Page 235

    12. Alignment 12.8.1 about warping overview image warping is the process of digitally manipulating an image to compensate for the distortion of the screen. Consequently, it can also be used to generate an image with irregular shape. While an image can be transformed in various ways, pure warping doe...

  • Page 236

    12. Alignment 12.8.2 warp activation - deactivation what can be done ? The warp functionality can be activated or deactivated. With 3d activated, warping can be enabled for sources up to 30 hz per eye. Above this frequency, warping is disabled. How to activate - deactivate 1. Press menu to activate ...

  • Page 237

    12. Alignment 12.8.3 start up manual adjustment how to start up 1. Press menu to activate the menus and select alignment → warping → .Warp adjust. The warp adjust menu opens. The content of this warp adjust menu depends on the selection. When no warp was done before, the menu starts as a sort of wiz...

  • Page 238

    12. Alignment 6 remove / show points 7 hardware reset of warp module 234 r5905158 hdf series 08/12/2016.

  • Page 239

    12. Alignment 12.8.4 warp adjustment principle description warping adjustment enables the relocation of pixel groups in an image in order to introduce spacial distortion. To make the procedure comprehensible, there are some rules and features. The use of warping adjustment leads to image quality los...

  • Page 240

    12. Alignment in 2 x 2 mode, we only have one level, including all four (2 x 2) anchor points, being the image corners. This mode is especially used to correct horizontal and vertical keystone. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 0 2 1 3 4 6 5 7 8...

  • Page 241

    12. Alignment 12.8.5 setting the warping level how to select 1. With the warping menu displayed, use the ▲ or ▼ key to select more or less pixels to adjust. Switching between the more or less pixels icon can be done with the ◄ or ► key. 1 2 image 12-37 warp level selection 1 increment pixels 2 decre...

  • Page 242

    12. Alignment 12.8.6 warp adaptation steps about the steps an anchor point can be moved with a fixed number of steps: 1, 10 or 100. It is also possible to move an anchor point with custom number of steps or a part of a step. How to select a predefined number of steps 1. Use the ▲ or ▼ key to go to t...

  • Page 243

    12. Alignment 12.8.7 making selections and adjustments about a selection of a function the current selection is indicated in yellow. The current position of the cursor is indicated in blue. The arrow keys are use to move the cursor to a new selection. How to make a selection 1. Use the ▲ or ▼ key to...

  • Page 244

    12. Alignment 6 rotate 7 rotation point 240 r5905158 hdf series 08/12/2016.

  • Page 245

    12. Alignment 12.8.8 keystone correction workflow adjusting vertical and horizontal keystone 1. Select the 2 x 2 adjustment level. See "setting the warping level", page 237. The default selected anchor point is the left top corner of the image. 2. Select the desired warp area. Depending on the selec...

  • Page 246

    12. Alignment 12.8.9 linearity adjustment, workflow adjusting vertical and horizontal linearity 1. Select the 2 x 2 adjustment level. See "setting the warping level", page 237. The default selected anchor point is the left top corner of the image. 2. Select the desired warp area. Depending on the se...

  • Page 247

    12. Alignment 12.8.10 selecting and changing the position of a specific point about point selection depending on the warp level, number of selectable points, a specific point can be selected and moved in any direction. The coordi- nate system works with 33 x 33 pixels (0 to 32). Depending on the war...

  • Page 248

    12. Alignment 12.8.11 scaling the image about scaling it is possible to scale the whole image. This is considered as an equal scale of the 4 corner points in 2 x 2 mode. The warping adaptation window is used to scale the image. How to scale 1. Select the 2 x 2 adjustment level. See "setting the warp...

  • Page 249

    12. Alignment 12.8.12 shifting the image about shifting it is possible to shift the whole image. This is considered as an equal movement of the 4 corner points in 2 x 2 mode. The warping adaptation window is used for adjusting the shift. After shifting the image parts of the image might not be visib...

  • Page 250

    12. Alignment 12.8.13 rotating the image about rotating the image can be rotated around a predefined point. This is considered as an equal rotation of the 4 corner points in 2 x 2 mode and with the full area selected. The default rotation point is the center of the image. Image 12-51 rotation select...

  • Page 251

    12. Alignment 1 2 3 image 12-54 rotate image 3. Select warp adaptation, angle. 4. Use the ◄ or ► key to change the rotation angle. Or, press enter to open the warping adaptations window. Use the ◄ or ► key to change the angle. Image 12-55 warping adaptation, angle r5905158 hdf series 08/12/2016 247.

  • Page 252

    12. Alignment 12.8.14 hardware reset what can be done ? During some combinations of adjustments, it is possible that the warping get stuck. Than it is possible to reset the board and restart from a clean adjustment. How to reset 1. Use the arrow keys to select the reset icon on the general icon bar ...

  • Page 253

    12. Alignment 12.8.15 osd opacity about the opacity of the osd menus during the warp adjustment process the osd menu is displayed on top the warp grid. To see the grid and the grid points, reduce the opacity of the osd menu. 1 21 11 6 16 5 3 2 4 25 15 23 13 24 22 10 20 8 18 12 14 7 9 19 17 13 8 8 8 ...

  • Page 254

    12. Alignment 2. Use the ◄ or ► key to change the opacity. 250 r5905158 hdf series 08/12/2016.

  • Page 255

    12. Alignment 12.8.16 warp file service, load file what can be done? A predefined warp configuration can be loaded in the warp board as active warp configuration file. To exclude the warp functionality, load the file nodistortion.Txt. How to load 1. Press menu to activate the menus and select alignm...

  • Page 256

    12. Alignment 12.8.17 warp file service, save to file what can be done? The current warp settings are saved in the current active file how to save 1. Press menu to activate the menus and select alignment → warping → .Warp file service → .Save. Image 12-66 main menu, alignment image 12-67 alignment, ...

  • Page 257

    12. Alignment 12.8.18 warp file service, save as what can be done? The current settings can be saved into a new file. How to save 1. Press menu to activate the menus and select alignment → warping → .Warp file service → .Save as. Image 12-70 main menu, alignment image 12-71 alignment, warping image ...

  • Page 258

    12. Alignment 12.8.19 warp file service, rename file how to rename? 1. Press menu to activate the menus and select alignment → warping → .Warp file service → .Rename. Image 12-74 main menu, alignment image 12-75 alignment, warping image 12-76 warping, file service image 12-77 rename warp file image ...

  • Page 259

    12. Alignment 12.8.20 warp file service, delete file how to delete 1. Press menu to activate the menus and select alignment → warping → .Warp file service → .Delete. Image 12-80 main menu, alignment image 12-81 alignment, warping image 12-82 warping, file service image 12-83 delete warp file 2. Pres...

  • Page 260

    12. Alignment 12.8.21 warp file service, delete all files what can be done? All custom created warp files can be deleted. How to delete 1. Press menu to activate the menus and select alignment → warping → .Warp file service → .Delete all. Image 12-86 main menu, alignment image 12-87 alignment, warpi...

  • Page 261

    12. Alignment 12.8.22 warp board reset what can be done? In some circumstances the hardware of the warping get stuck. A hard reset of the board is the only solution. With warp board reset, the board is reset but the current values remain in the board. How to reset the board 1. Press menu to activate...

  • Page 262

    12. Alignment 12.8.23 warp board and values reset what can be done? With some extreme warp values the hardware of the warping can get stuck. With only a hard reset of the board, it starts up with the same extreme values and get stuck immediately. So that is not the solution. Therefore, while executi...

  • Page 263

    12. Alignment 12.8.24 alternative side keystone about the alternative side keystone for 3d sources with a frequency higher than 30 hz/eye, the warp unit cannot be used anymore. Therefor, for these source the alternative side keystone can be used. How to adjust 1. Press menu to activate the menus and...

  • Page 264

    12. Alignment 12.9 blanking adjustment what can be done ? Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). A ’0’ on the bar scale indicates no blanking. Which blankin...

  • Page 265

    12. Alignment image 12-101 main menu, alignment image 12-102 alignment, blanking 2. Press enter to select. The blanking adjustment menu opens. Image 12-103 blanking adjustment 3. Use the ▲ or ▼ key to select the desired blanking adjustment and adjust with the ◄ or ► key. Select reset to reset all bl...

  • Page 266

    12. Alignment 12.10 contrast-intensity purpose contrast : change the contrast of the complete output signal (main and pip window together) of the projected image. Intensity : change the brightness of the complete output signal (main and pip window together) of the projected image. How to set up 1. P...

  • Page 267

    12. Alignment 12.11 gamma about gamma gamma is an image quality enhancement function that offers a richer image by brightening the already darker portions of the image without altering the brightness of the brighter portions (contrast feeling enhanced). How to adjust 1. Press menu to activate the me...

  • Page 268

    12. Alignment 12.12 internal patterns what can be done with these patterns? The projector is equipped with different internal patterns which can be used for measurement and alignment purposes. How to select a pattern 1. Press menu to activate the menus and select alignment → internal patterns. Image...

  • Page 269

    12. Alignment 12.13 color space color space a color space or color standard is a mathematical representation for a color. For example the rgb color space is based on a cartesian coordinate system. What can be adjusted ? The color space (gamut), the collection of colors which can be reproduced by the...

  • Page 270

    12. Alignment image 12-116 color space — confirmation 4. When [on] is selected and the color temperature is correct, use the ▲ or ▼ key to select the desired color space and press enter to select. Projector maximum color space ebu european broadcasting union. This organization defines a european sta...

  • Page 271

    12. Alignment 12.14 scenergix r5905158 hdf series 08/12/2016 267.

  • Page 272

    12. Alignment 12.14.1 introduction why scenergix ? When working in a multichannel setup the hdf series projector and its soft edge possibilities enable an image blending that gives the appearance of a single view, thus achieving realistic immersion for the majority of wide screen applications. Scene...

  • Page 273

    12. Alignment 12.14.2 preparations scenergix preparations to ensure proper scenergix adjustment, be sure that the following adjustments are done perfectly on all projectors: • convergence • geometry • color matching (color temperature, color standard, input balance, gamma) r5905158 hdf series 08/12/...

  • Page 274

    12. Alignment 12.14.3 scenergix activation how to activate 1. Press menu to activate the menus and select alignment → scenergix. Image 12-121 main menu, alignment image 12-122 alignment, scenergix 2. Press enter to select. The scenergix menu opens. Image 12-123 scenergix, status 3. Use the ▲ or ▼ ke...

  • Page 275

    12. Alignment 12.14.4 scenergix pattern what can be done? To make the scenergix adjustment more easy, an internal pattern can be displayed. How to select 1. Press menu to activate the menus and select alignment → scenergix → scenergix pattern. Image 12-124 main menu, alignment image 12-125 alignment...

  • Page 276

    12. Alignment 12.14.5 scenergix adjustment lines what can be done? Border lines for the blending areas can be displayed while adjusting the white and black level. Adjustment lines can be activated when scenergix pattern is [on]. How to display 1. Press menu to activate the menus and select alignment...

  • Page 277

    12. Alignment 12.14.6 data doubling about data doubling when a source (a) must be displayed via 2 projectors as one image (b), the vertical and horizontal start position and the size must be determined so that each projector displays a part of the image. The overlap area can be adjusted with the sce...

  • Page 278

    12. Alignment image 12-132 main menu, alignment image 12-133 alignment, scenergix image 12-134 scenergix, data doubling image 12-135 data doubling, status 2. Select status and press enter to toggle between [on] and [off]. [on] : data doubling is activated. [off] : data doubling is deactivated. 3. Se...

  • Page 279

    12. Alignment 12.14.7 white level adjustment (blending area) how to set 1. Press menu to activate the menus and select alignment → scenergix → white level. Image 12-136 main menu, alignment image 12-137 alignment, scenergix image 12-138 scenergix, white level 2. Press enter to select the white level...

  • Page 280

    12. Alignment image 12-140 width selections 4. Set first the width for the first projector and repeat for the second one. Image 12-141 width set up for projector 1 276 r5905158 hdf series 08/12/2016.

  • Page 281

    12. Alignment image 12-142 width set up for projector 2 to eliminate all blending settings, select reset and press enter. R5905158 hdf series 08/12/2016 277.

  • Page 282

    12. Alignment 12.14.8 black level adjustment why black level adjustment for dark images, the overlap zone will be brighter then the rest of the images. Typically for dlp projectors, next to the overlap zone, a brighter area is recognized. This area is known as a dlp leakage area. This area must also...

  • Page 283

    12. Alignment image 12-146 scenergix, black level 2. Press enter to select the black level adjustments. Image 12-147 black level, area 3. Use the ▲ or ▼ key to select one of the four size adjustments. Use the ◄ or ► key to move the green border line to the desired position. R5905158 hdf series 08/12...

  • Page 284

    12. Alignment image 12-148 dlp leakage area 1 overlap area 2 dlp leakage area use the reset item to reset all area values. How to adjust 1. Press menu to activate the menus and select alignment → scenergix → black level. Image 12-149 main menu, alignment image 12-150 alignment, scenergix 280 r590515...

  • Page 285

    12. Alignment image 12-151 scenergix, black level 2. Press enter to select and use the ▲ or ▼ key to select a color to adjust or select all colors to adjust all colors at the same time. Image 12-152 black level, adjust 3. Adjust the black level of area a until the black level of area a, b and c are ...

  • Page 286

    12. Alignment 12.14.9 scenergix reset what can be done? All scenergix values can be set back to the default values. How to reset 1. Press menu to activate the menus and select alignment → scenergix → reset. Image 12-154 main menu, alignment image 12-155 alignment, scenergix image 12-156 scenergix, r...

  • Page 287

    12. Alignment 12.15 3d glasses overview • dark time adjustment • left-right output reference delay • 3d sync loop through • upper limit for triple or double flash r5905158 hdf series 08/12/2016 283.

  • Page 288

    12. Alignment 12.15.1 dark time adjustment what can be done? The principle of a pair of stereo glasses is : 1. When the left image is projected, the left shutter is open, allowing the left eye to see the left image. The shutter for the right eye is closed. 2. During the blanking period, before proje...

  • Page 289

    12. Alignment left shutter open op en ing op en ing clo sin g clo sin g closed right shutter open closed dlp mirrors active blanking time opening too early and/or closing too late = cross talk t s t e r e o g l a s s e s image 12-158 shutters closing too late and/or opening too early cause cross-tal...

  • Page 290

    12. Alignment image 12-160 main window image 12-161 alignment, 3d glasses 2. Press enter. 3. Use the ▲ or ▼ key to select dark time adjustment image 12-162 dark time adjustment 4. Use the ◄ or ► key to change the dark time until the correct value is reached. The actual used dark time is indicated ne...

  • Page 291

    12. Alignment 12.15.2 left-right output reference delay what can be done? With l/r output reference delay it is possible to apply an adjustable time delay on the stereo emitter signal. Image frame left 3d sync left right delay time 3d sync left right frame left frame right t without output reference...

  • Page 292

    12. Alignment image 12-166 output reference dellay 4. Use the ◄ or ► key to change the l/r output reference delay value until the correct value is reached. 288 r5905158 hdf series 08/12/2016.

  • Page 293

    12. Alignment 12.15.3 3d sync loop through what can be done? The incoming 3d sync signal can routed to the 3d sync output connector. How to activate 1. Press menu to activate the menus and select alignment → 3d glasses. Image 12-167 main window image 12-168 alignment, 3d glasses 2. Press enter. 3. U...

  • Page 294

    12. Alignment 12.15.4 upper limit for triple or double flash what can be done? The upper limit for triple flash can be set. When the input frame rates are below this limit, the result will be displayed at triple frame rate. The upper limit for double flash can be set. When the input frame rates are ...

  • Page 295

    12. Alignment 12.16 high end systems mirror about the mirror the digital mirror is dmx controlled. This control can be done via the projector or via projector toolset. External dmx control is still possible. Almost any image can be displayed on almost any place in the room using the pan and tilt adj...

  • Page 296

    12. Alignment image 12-176 projector controlled 2. Use the ◄ or ► key to change the value between -128 and 128. 3. Use the ▲ or ▼ key to select fine pan or fine tilt. 4. Use the ◄ or ► key to change the value between -128 and 128. Store settings 1. To change the store settings, use the ▲ or ▼ key to...

  • Page 297: 13. Projector Control

    13. Projector control 13. Projector control overview • projector control menu overview • individual projector address • projector common address • serial communication • network • ir control switching • dmx • buttons • menu position • local lcd • language selection • scheduler • gsm configuration, a...

  • Page 298

    13. Projector control 13.1 projector control menu overview overview table level 1 level 2 level 3 projector control projector address projector address common address serial communication baud rate interface standard network wired dhcp [on] [off] ip address subnet mask default gateway wireless statu...

  • Page 299

    13. Projector control 13.2 individual projector address about individual projector address before a projector, and only this projector, can be controlled via a remote control, an individual address must be entered in the projector. This individual projector address can then be used to control the pr...

  • Page 300

    13. Projector control 13.3 projector common address about common address a common address can be ’0’ or ’1’. Any command coming from a remote control programmed with that common address will be executed. How to set 1. Press menu to activate the menus and select projector control → projector address ...

  • Page 301

    13. Projector control 13.4 serial communication overview • baud rate setup • interface standard r5905158 hdf series 08/12/2016 297.

  • Page 302

    13. Projector control 13.4.1 baud rate setup what can be done ? The baud rate for to establish a serial communication with a computer can be set. How to set 1. Press menu to activate the menus and select projector control → serial communication → baudrate. Image 13-9 main menu, projector control ima...

  • Page 303

    13. Projector control 13.4.2 interface standard what can be done? The communication protocol for the communication between the projector and a computer can be set to rs232 or rs422. How to set up 1. Press menu to activate the menus and select projector control → serial communication. Image 13-12 mai...

  • Page 304

    13. Projector control 13.5 network about a network connection a network connection can be made via a wired connection or via the optional wireless unit. Overview • introduction to a network connection • wired dhcp set up • wired ip address set up • wired subnet mask set up • wired default gateway se...

  • Page 305

    13. Projector control 13.5.1 introduction to a network connection dhcp dynamic host configuration protocol. Dhcp is a communications protocol that lets network administrators manage centrally and automate the assignment of ip addresses in an organization’s network. Using the internet protocol, each ...

  • Page 306

    13. Projector control 13.5.2 wired dhcp set up how to set up 1. Press menu to activate the menus and select projector control → network. Image 13-15 main menu, projector control image 13-16 projector control, network image 13-17 wired dhcp 2. Use the ▲ or ▼ key to select dhcp under wired and press e...

  • Page 307

    13. Projector control 13.5.3 wired ip address set up how to set up 1. Press menu to activate the menus and select projector control → network. Image 13-18 main menu, projector control image 13-19 projector control, network image 13-20 ip address 2. Use the ▲ or ▼ key to select ip address under wired...

  • Page 308

    13. Projector control 3. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatica...

  • Page 309

    13. Projector control 13.5.4 wired subnet mask set up subnet for wired and wifi must be different ! How to set up 1. Press menu to activate the menus and select projector control → network. Image 13-22 main menu, projector control image 13-23 projector control, network image 13-24 subnet mask 2. Use...

  • Page 310

    13. Projector control image 13-25 fill subnet mask image 13-26 fill subnet mask 3. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered i...

  • Page 311

    13. Projector control 13.5.5 wired default gateway set up how to set up 1. Press menu to activate the menus and select projector control → network. Image 13-27 main menu, projector control image 13-28 projector control, network image 13-29 network, default gateway 2. Use the ▲ or ▼ key to select def...

  • Page 312

    13. Projector control 3. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatica...

  • Page 313

    13. Projector control 13.5.6 wireless network activation can only be used with a wireless network module installed. What can be done ? Before a wireless network can be used, the status must be set to on. How to activate 1. Press menu to activate the menus and select projector control → network → wir...

  • Page 314

    13. Projector control image 13-34 wireless, status 3. Press enter to toggle the status between [off] and [on]. 310 r5905158 hdf series 08/12/2016.

  • Page 315

    13. Projector control 13.5.7 wireless access points selection and setup these menu items are only accessible when wireless network status is set to [on]. Scan for access points 1. Select scan access points and press enter to start the scan. Image 13-35 scan access points image 13-36 scan access poin...

  • Page 316

    13. Projector control image 13-39 open network connection 2. Press enter to activate the input field. 3. Enter the passphrase. The input is case sensitive. Press enter to finish the input of the passphrase. 4. Use the ▲ or ▼ key to select apply and press enter to open the network connection. An ip a...

  • Page 317

    13. Projector control 13.5.8 wireless dhcp set up can only be used with a wireless network module installed. How to set up 1. Press menu to activate the menus and select projector control → network → wireless setup . Image 13-40 main menu, projector control image 13-41 projector control, network ima...

  • Page 318

    13. Projector control 13.5.9 wireless fixed ip address set up can only be used with a wireless network module installed. How to set up 1. Press menu to activate the menus and select projector control → network → wireless setup. Image 13-44 main menu, projector control image 13-45 projector control, ...

  • Page 319

    13. Projector control image 13-48 wireless ip address input 3. Press enter to open the wireless menu. 4. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. Whe...

  • Page 320

    13. Projector control 13.5.10 wireless subnet mask set up can only be used with a wireless network module installed. Subnet for wired and wifi must be different ! How to set up 1. Press menu to activate the menus and select projector control → network → wireless setup. Image 13-49 main menu, project...

  • Page 321

    13. Projector control image 13-53 wireless subnet mask, input 4. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the ne...

  • Page 322

    13. Projector control 13.5.11 wireless default gateway set up can only be used with a wireless network module installed. How to set up 1. Press menu to activate the menus and select projector control → network → wireless setup. Image 13-54 main menu, projector control image 13-55 projector control, ...

  • Page 323

    13. Projector control image 13-58 wireless default gateway, input 4. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, th...

  • Page 324

    13. Projector control 13.6 ir control switching what can be done ? Each ir receiver inside the projector can be activated or deactivated. When an ir receiver is deactivated, no ir signal sent to this ir receiver will be processed. How to activate or deactivate 1. Press menu to activate the menus and...

  • Page 325

    13. Projector control 13.7 dmx overview • dmx address • dmx universe • dmx mode • art-net dmx • front xlr output voltage control • monitor • dmx shutdown • dmx shutdown retarding time about the ways to control the projector via dmx with a standard dmx cable equipped with xlr connector dmx signals ca...

  • Page 326

    13. Projector control 13.7.1 dmx address what should be done ? Before a projector can execute dmx commands, a unique address, called dmx address, should be given to the projector. This address can vary from 1 to 512. How to set the dmx address 1. Press menu to activate the menus and select projector...

  • Page 327

    13. Projector control 3. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatica...

  • Page 328

    13. Projector control 13.7.2 dmx universe what can be done ? Depending on the dmx mode, one dmx universe can contain a different number of projectors. E.G. Dmx mode = basic, the dmx universe can contain up to 256 projectors universes are only meaningful for art-net applications as only there multipl...

  • Page 329

    13. Projector control image 13-70 dmx universe 3. Use the ▲ or ▼ key to change the selected character. Use the ◄ or ► key to select another character. Note: digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character wi...

  • Page 330

    13. Projector control 13.7.3 dmx mode what can be done ? 3 modes for dmx are available: • basic which has currently 2 channels implemented. • extended which has currently 10 channels implemented • full which has currently 9 channels implemented and a 10th free channel. Depending on the dmx applicati...

  • Page 331

    13. Projector control 13.7.4 art-net dmx what can be done ? Dmx can be sent via ethernet to the projector. This function can be enabled or disabled. Art-net dmx [on] : dmx via ethernet is enabled. Art-net dmx [off] : dmx via ethernet is disabled. How to toggle 1. Press menu to activate the menus and...

  • Page 332

    13. Projector control 13.7.5 front xlr output voltage control what can be done ? The output voltage on the front xlr connector can be enabled or disabled. The output voltage level can be set to 0v, 9v, 12v or 24v. Dmx art-net can also enable the output voltage on the front xlr connector. To avoid th...

  • Page 333

    13. Projector control image 13-80 main menu, projector control image 13-81 projector control, dmx image 13-82 front xlr output voltage level 2. Press enter to toggle between [0 volt], [9 volt], [12 volt] and [24 volt]. R5905158 hdf series 08/12/2016 329.

  • Page 334

    13. Projector control 13.7.6 monitor what can be done ? If a dmx device is connected, the settings per channel can be displayed in an on screen menu. How to start up the monitoring 1. Press menu to activate the menus and select projector control → dmx → monitor. Image 13-83 main menu, projector cont...

  • Page 335

    13. Projector control 13.7.7 dmx shutdown what can be done? Projector can be forced to go in shutdown after a certain retarding time when no dmx signals are available. How to activate/deactivate 1. Press menu to activate the menus and select projector control → dmx → shutdown. Image 13-87 main menu,...

  • Page 336

    13. Projector control 13.7.8 dmx shutdown retarding time about the shutdown retarding time the retarding time is the time between no dmx is detected and the moment that the projector shuts down. How to set the retarding time 1. Press menu to activate the menus and select projector control → dmx → sh...

  • Page 337

    13. Projector control 13.8 buttons overview • standby button • shortcut keys r5905158 hdf series 08/12/2016 333.

  • Page 338

    13. Projector control 13.8.1 standby button what can be done ? When going to standby by pressing the standby button, the following can happen: • only lamp will be switched off • lamp will be switched off and projector electronics will be powered down after an after cool period (eco standby) in eco s...

  • Page 339

    13. Projector control 13.8.2 shortcut keys what can be done? An overview of the shortcut allocations with the corresponding menu is given. Those printed in bold are allocated. The allocated shortcut keys can be cleared within this menu. How to clear a shortcut key 1. Press menu to activate the menus...

  • Page 340

    13. Projector control 13.9 menu position what is possible? The on screen menu and the bar scale can be positioned on different places on the screen. The following positions are possible for both • right-top • right-mid • right-bottom • mid-top • mid-mid • mid-bottom • left-top • left-mid • left-bott...

  • Page 341

    13. Projector control 13.10 local lcd what is possible ? The back light of the local lcd can be adapted to the needs of the environment. A time out for the local lcd can be set. If there is nothing done on the local lcd, it can go out after a time out. How to set up 1. Press menu to activate the men...

  • Page 342

    13. Projector control 13.11 language selection what can be done? The user can change the language of the on screen menus and the local display menus to one of the available languages. The following languages are available: • english • french • german • spanish • portuguese • japanese • chinese • kor...

  • Page 343

    13. Projector control 13.12 scheduler about the scheduler the scheduler allows to start up different tasks at a given time which can control the screen layout and the status of the lamp. These tasks can be scheduled in time with a certain recurrence and occurrence. Multiple tasks can be added to the...

  • Page 344

    13. Projector control 13.12.1 add a task to the list how to add 1. Press menu to activate the menus and select projector control → scheduler → add task. Image 13-110 main menu, projector control image 13-111 projector control, scheduler image 13-112 scheduler, add task 2. Press enter to open the tas...

  • Page 345

    13. Projector control image 13-114 time setup 3. Select recurrence and press enter; use the ◄ or ► key to change the recurrence. Image 13-115 recurrence setup recurrence : the time between two starts of the same task. The value can be changed between 1 and 99. 1 starts every day 2 starts every 2 day...

  • Page 346

    13. Projector control image 13-116 occurrence setup occurrence : the number of loops that will take place as set in the recurrence. E.G; an occurrence of 2 with a recurrence of 3 means that the schedule will be executed at the start date, start date + 3 and due to the occurrence (=2) also at start d...

  • Page 347

    13. Projector control 13.12.2 edit a task what can be done? An existing task in the list of tasks can be edited and saved with the same name. How to edit 1. Press menu to activate the menus and select projector control → scheduler → edit task. Image 13-118 main menu, projector control image 13-119 p...

  • Page 348

    13. Projector control image 13-122 edit task the following items can be changed in the same way as creating a new task. For more info, see "add a task to the list", page 340: - date and time - recurrence - routine - lamp status changing the name and applying the task will replace the selected task w...

  • Page 349

    13. Projector control 13.12.3 delete task what can be done? A task stored in the list of tasks can be deleted from that list. How to delete 1. Press menu to activate the menus and select projector control → scheduler → delete task. Image 13-123 main menu, projector control image 13-124 projector con...

  • Page 350

    13. Projector control 13.12.4 scheduler, on or off what can be done? The scheduler can be switched on or off. When switched on, the tasks in the list will be executed on the given time. How to toggle the scheduler 1. Press menu to activate the menus and select projector control → scheduler → schedul...

  • Page 351

    13. Projector control 13.13 gsm configuration, activation only possible when a gsm module with sim card is installed in the projector. What can be done ? To configure the projector software with the installed sim card, a correct pin code (4digits) must be entered. As the pin code cannot be checked w...

  • Page 352

    13. Projector control press enter when the 4 digits are entered. Image 13-136 pin code entered 4. Select ok and press enter to configure the software. Replacing a sim card with a new one 1. Before removing the current mounted sim card, select projector control → gsm configuration → gsm pincode image...

  • Page 353

    13. Projector control 13.14 gsm configuration, subscription about sms subscription when subscripted for notifications, the projector will send out sms messages when notifications occur with severity “critical”, “error” or “warning”. How to subscribe via the osd menu 1. Press menu to activate the men...

  • Page 354

    13. Projector control the software checks if the + is entered and that at least 7 digits are entered. When it is not a valid number, the number field next to the selected subscriber remain blank. This procedure can be repeated for subscriber 2 and 3. 5. Select ok and press enter to configure the sub...

  • Page 355

    13. Projector control 13.15 flex, light output configuration r5905158 hdf series 08/12/2016 351.

  • Page 356

    13. Projector control 13.15.1 about flex, light output control overview with the flex technology the projector owners can lock the light output to different levels. The locking can be done via 3 different ways: • via projector toolset when connected via an ethernet connection with the projector. See...

  • Page 357

    13. Projector control 13.15.2 light output configuration via osd menu what can be done ? The activation code can be entered by the projector user. This code is validated and when valid the maximum light output is set accordingly. How to set 1. Press menu to activate the menus and select projector co...

  • Page 358

    13. Projector control 13.15.3 configure projector’s light output via sms projector must be equipped with the optional gsm module. What can be done ? An sms message with certain structure must be sent to the sim card of the projector. This message will be picked up and decoded. The projector will be ...

  • Page 359

    13. Projector control 13.16 sms services projector must be equipped with the optional gsm module. Overview • request for notifications • request for information • lamp ignition admission r5905158 hdf series 08/12/2016 355.

  • Page 360

    13. Projector control 13.16.1 request for notifications what can be done ? Via an sms message sent from any cell phone to the gsm number associated with the projector, notification information can be requested. The receiving projector analyses the message. The projector answers with an sms of maximu...

  • Page 361

    13. Projector control 13.16.2 request for information request for information via an sms message sent from any cell phone to the gsm number associated with the projector, projector information can be re- quested. The receiving projector analyses the message. The projector answers with an sms of maxi...

  • Page 362

    13. Projector control 13.16.3 lamp ignition admission what can be done? Via an sms message sent from any cell phone to the gsm number associated with the projector, lamp ignition admission can be enabled or disabled. When enabled, the user can start up the projector in a normal way. When disabled, t...

  • Page 363: 14. Service

    14. Service 14. Service overview • service menu overview • identification • diagnosis • internal service patterns • convergence • factory defaults • usb memory • reset formatter • refill mode • save custom settings • special hd camera mode • auto dimming when over-temperature • time and date r590515...

  • Page 364

    14. Service 14.1 service menu overview overview table level 1 level 2 level 3 service identification diagnostics version measurements logging board id notifications tilt sensor internal service patterns pmp in osd pmp out fib convergence blue green on blue red on blue factory defaults usb memory sav...

  • Page 365

    14. Service 14.2 identification what can be seen? The identification screen shows the general information about the projector. The following items will be displayed: • projector type • projector address • software version • configuration • baudrate • ip address • mac address • status of the on scree...

  • Page 366

    14. Service 14.3 diagnosis what can be seen? The diagnosis menu gives the possibility to get an overview of the working of the projector. Overview • versions • measurements • logging • board id • notification • tilt sensor 362 r5905158 hdf series 08/12/2016.

  • Page 367

    14. Service 14.3.1 versions about versions the table gives an overview between the reference software and the current installed software. The reference software is the latest correctly installed package. The current is the updated software (upgrade of downgrade). Once the complete current is updated...

  • Page 368

    14. Service image 14-7 diagnosis, versions list 364 r5905158 hdf series 08/12/2016.

  • Page 369

    14. Service 14.3.2 measurements about measurements measurements contains the following parts: • voltages • temperatures • fan speeds all tables are built up in an identical way. The current measured value is surrounded with the low and high error and warning limits. Once one of these values are cros...

  • Page 370

    14. Service image 14-13 overview temperatures image 14-14 overview fan speeds image 14-15 overview miscellaneous items 366 r5905158 hdf series 08/12/2016.

  • Page 371

    14. Service 14.3.3 logging what can be done? Projector hosts two log files: one managed bythe main controller and one specific for the lamp power supply. How to display the logging 1. Press menu to activate the menus and select service → diagnosis → logging. Image 14-16 main menu, service image 14-1...

  • Page 372

    14. Service image 14-21 lamp power supply logging 368 r5905158 hdf series 08/12/2016.

  • Page 373

    14. Service 14.3.4 board id about board id the board id window gives an overview of the modules with their article number, serial number, etc. How to get an overview 1. Press menu to activate the menus and select service → diagnosis → board id. Image 14-22 main menu, service image 14-23 service, dia...

  • Page 374

    14. Service 14.3.5 notification about notifications notifications are warnings and errors displayed on the local lcd or on the osd since power on of the projector. Once powered off, the notification logging is cleared. How to display 1. Press menu to activate the menus and select service → diagnosis...

  • Page 375

    14. Service 14.3.6 tilt sensor what is possible? The built-in tilt sensor can be read out to see if the projector is used in an allowed position. The status field indicates whether the rotation of the projector is normal or abnormal. Using a projector with an abnormal rotation can severely damage th...

  • Page 376

    14. Service 14.4 internal service patterns how to select 1. Press menu to activate the menus and select service → internal service patterns. Image 14-34 main menu, service image 14-35 service, internal service patterns image 14-36 internal service patterns, pmp in 2. Use the ▲ or ▼ key to select the...

  • Page 377

    14. Service image 14-38 input test patterns image 14-39 input test patterns pmp in patterns image 14-40 pmp in test patterns to change the options for the selected pattern, use he ► key to open these options. The number of options can change for the different patterns. Image 14-41 pmp in test patter...

  • Page 378

    14. Service image 14-43 osd test patterns pmp out patterns image 14-44 internal service patterns, pmp out press enter to display the list of possible patterns. Image 14-45 pmp out test patterns to change the options for the selected pattern, use he ► key to open these options. The number of options ...

  • Page 379

    14. Service fib patterns image 14-47 internal service patterns, fib press enter to display the list of possible patterns. Image 14-48 fib test patterns r5905158 hdf series 08/12/2016 375.

  • Page 380

    14. Service 14.5 convergence what can be done? The convergence patterns can be used to check the convergence alignment of red, green and blue. If there is a misalignment of at least one 1 pixel, an electronic realignment is possible. Mechanical realignment of the convergence can only be done by a qu...

  • Page 381

    14. Service image 14-53 4. Use the ▲ or ▼ key to adjust vertical and the ◄ or ► key to adjust vertical convergence. Adjust until the crossing of the center green (red) convergence pattern coincide with the diagonal line of the center blue con- vergence pattern. R5905158 hdf series 08/12/2016 377.

  • Page 382

    14. Service 14.6 factory defaults what can be done? All settings of the projector will be set to the original factory settings. All user settings are erased with this operation. How to return to the factory defaults 1. Press menu to activate the menus and select service → factory defaults. Image 14-...

  • Page 383

    14. Service 14.7 usb memory purpose 2 functions are available • custom settings can be saved on a usb stick. • a selection of saved settings can be (down)loaded via an usb stick on the projector. How to save custom settings 1. Press menu to activate the menus and select service → usb memory. Image 1...

  • Page 384

    14. Service image 14-60 main menu, service image 14-61 service, usb memory image 14-62 usb memory selection 2. Select load custom settings and press enter. An overview of the available sets of custom settings is given. Image 14-63 custom settings files 3. Select a set and press enter to upload this ...

  • Page 385

    14. Service 14.8 reset formatter why and when a reset formatter is necessary when e.G. A color is missing, artifacts are visible in the image or image is frozen and the formatter test patterns cannot be displayed. How to reset 1. Press menu to activate the menus and select service → reset formatter....

  • Page 386

    14. Service 14.9 refill mode before selecting refill mode, take first all preparations necessary to refill the cooling circuit. What can be done? When all necessary preparations are taken, the refill mode activates automatically the refill process. For more information about the refill process, cons...

  • Page 387

    14. Service 14.10 save custom settings what can be done ? The current custom settings can be saved to internal backup device in the same way as it would be done when the projector lamp was switched off. When settings are changed when the lamp is off, a manual save custom settings must be executed to...

  • Page 388

    14. Service 14.11 special hd camera mode what can be done ? "special hd camera mode" enables special sequences for the dmd’s to support specific sources such as the thompson grass valley worldcam. It shouldn’t be used in any other circumstances as it would cause image flicker and dimmed images with ...

  • Page 389

    14. Service 14.12 auto dimming when over-temperature what can happen? When an over-temperature is detected, the projector starts dimming the lamp so that the projector can cool down. How to activate - deactivate 1. Press menu to activate the menus and select service → auto dimming when overtemperatu...

  • Page 390

    14. Service 14.13 time and date how to set 1. Press menu to activate the menus and select service → time and date. Image 14-77 main menu, service image 14-78 service, time and date image 14-79 date and time set up image 14-80 date and time set up 2. Use the ▲ or ▼ key to select hour, minute, day, mo...

  • Page 391: 15. Maintenance

    15. Maintenance 15. Maintenance about this chapter this chapter contains detailed maintenance procedures like dust filter replacement, lens cleaning etc. These procedures can easily be performed by the operator of the projector. R5905158 hdf series 08/12/2016 387.

  • Page 392

    15. Maintenance 15.1 cleaning the lens to minimize the possibility of damage to optical coatings, or scratches to lens surfaces follow the cleaning procedure as described here precisely. Necessary tools • compressed air. • clean toraysee® cloth or any micro fiber lens cleaning cloth. • clean cotton ...

  • Page 393

    15. Maintenance 15.2 cleaning the exterior of the projector how to clean the exterior of the projector ? 1. Switch off the projector and unplug the projector from the mains power net. 2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly dampene...

  • Page 394

    15. Maintenance 390 r5905158 hdf series 08/12/2016.

  • Page 395: Covers

    16. Removal and installation of the projector covers 16. Removal and installation of the projector covers about this chapter most maintenance and servicing procedures demand removing one or more of the projector covers to gain access to the parts to maintain or to service. To avoid redundancy, all p...

  • Page 396

    16. Removal and installation of the projector covers 16.1 removal of the front cover w arning : this procedure may only be performed by qualified technical service personnel. Necessary tools 7 mm flat screw driver. How to remove the front cover 1. Remove the lens. See “lens removal”. 2. Remove the r...

  • Page 397

    16. Removal and installation of the projector covers 16.2 removal of the side cover c aution : remove the side cover of the projector only in a clean and dust free area. Never remove the side cover in an area which is subject to airborne contaminants such as that produced by smoke machines or simila...

  • Page 398

    16. Removal and installation of the projector covers 16.3 removal of the light unit cover w arning : this procedure may only be performed by qualified technical service personnel. Necessary tools 7 mm flat screw driver. How to remove the light unit cover 1. Release the two captive screws at the top ...

  • Page 399

    16. Removal and installation of the projector covers 16.4 removal of the input cover w arning : this procedure may only be performed by qualified technical service personnel. Necessary tools 7 mm flat screw driver. How to remove the input cover 1. Release the two captive screws at the top and bottom...

  • Page 400

    16. Removal and installation of the projector covers 16.5 installation of the front cover w arning : this procedure may only be performed by qualified technical service personnel. Necessary tools 7 mm flat screw driver. How to install the front cover 1. Check if the front filter is present. 2. Ensur...

  • Page 401

    16. Removal and installation of the projector covers 16.6 installation of the side cover w arning : this procedure may only be performed by qualified technical service personnel. Necessary tools 7 mm flat screw driver. How to install the side cover 1. Check if all needed filters are present. 2. Chec...

  • Page 402

    16. Removal and installation of the projector covers 16.7 installation of the light unit cover w arning : this procedure may only be performed by qualified technical service personnel. Necessary tools 7 mm flat screw driver. How to install the light unit cover 1. Install the light unit cover of the ...

  • Page 403

    16. Removal and installation of the projector covers 16.8 installation of the input cover w arning : this procedure may only be performed by qualified technical service personnel. Necessary tools 7 mm flat screw driver. How to install the input cover 1. Install the input cover of the projector as fo...

  • Page 404

    16. Removal and installation of the projector covers 400 r5905158 hdf series 08/12/2016.

  • Page 405: 17. Servicing

    17. Servicing 17. Servicing about this chapter this chapter contains general servicing procedures like lamp house replacement, input unit replacement etc. These procedures may only be performed by qualified technical service personnel. Overview • inserting an input module • replacement of the dust f...

  • Page 406

    17. Servicing 17.1 inserting an input module w arning : switch off the projector and unplug the power cord before starting the procedure. How to insert 1. Loosen both screws of the dummy cover plate (1). 1 2 3 image 17-1 insert input module 2. Take off the dummy cover plate. 3. Insert the new input ...

  • Page 407

    17. Servicing 17.2 replacement of the dust filter on the front side necessary parts new hepa dust filter for the front side (r9854470). How to replace the hepa dust filter on the front side 1. Remove the front cover of the projector, see "removal of the front cover", page 392. 2. Remove the hepa dus...

  • Page 408

    17. Servicing 17.3 replacement of the dust filter on the bottom side necessary parts • new hepa dust filter for the bottom side (r9854480). • 2.5 mm allen key. How to replace the hepa dust filter on the bottom side 1. Remove the side cover of the projector, see "removal of the side cover", page 393....

  • Page 409

    17. Servicing a a image 17-7 bottom filter, fixation 7. Reinstall the side cover of the projector, see "installation of the side cover", page 397. C aution : never install a used hepa filter. Always install a new hepa filter. R5905158 hdf series 08/12/2016 405.

  • Page 410

    17. Servicing 17.4 replacement of the dust filter on the top side necessary parts new hepa dust filter for the top side (r9854480). How to replace the hepa dust filter on the top side 1. Remove the side cover of the projector, see "removal of the side cover", page 393. 2. Remove the filter (f) on th...

  • Page 411

    17. Servicing 17.5 pressure verification of the liquid cooling circuit c aution : the pressure of the liquid cooling circuit should be checked regularly. This pressure, indicated on the internal manometer, should be between 0,5 and 1 bar. If not, corrective action should be taken by qualified techni...

  • Page 412

    17. Servicing 17.6 removal of the lamp house w arning : this procedure may only be performed by qualified technical service personnel. C aution : never attempt to disassemble the lamp from its housing or to dispose of it. Return it to barco. Due to its high internal pressure, the lamp may explode in...

  • Page 413

    17. Servicing while starting up the projector, the electronics detect if a lamp is installed. If no lamp is installed, it is not possible to start up the projector. R5905158 hdf series 08/12/2016 409.

  • Page 414

    17. Servicing 17.7 installation of the lamp house w arning : this procedure may only be performed by qualified technical service personnel. C aution : never attempt to disassemble the lamp from its housing or to dispose of it. Return it to barco. Due to its high internal pressure, the lamp may explo...

  • Page 415

    17. Servicing image 17-13 6. Reinstall the lamp cover of the projector, see "installation of the light unit cover", page 398. While starting up the projector, the electronics detect if a lamp is installed. If no lamp is installed, it is not possible to start up the projector. R5905158 hdf series 08/...

  • Page 416

    17. Servicing 17.8 realignment of the lamp in its reflector why realigning the lamp ? With longer run times, the light output of the lamp will decrease, which results in a lower light output on the screen. This light output decrease can be compensated by readjusting the z-position of the lamp. W arn...

  • Page 417: A. Specifications

    A. Specifications a. Specifications r5905158 hdf series 08/12/2016 413.

  • Page 418

    A. Specifications 414 r5905158 hdf series 08/12/2016.

  • Page 419

    A. Specifications a.1 specifications of the hdf w22 overview projector type wuxga 3-chip dlp digital projector technology 0.96" dmd™ x3 resolution 1,920 x 1,200 brightness 22,000 center lumens / 20,000 ansi lumens* contrast ratio 1,900:1 (standard) / 2,200:1 (high contrast mode) brightness uniformit...

  • Page 420

    A. Specifications dissipation btu max. 13660 btu/h dimensions (wxlxh) 707 x 1,025 x 548mm / 27.83 x 40.35 x 21.57 inches weight 99kg (218.25lbs) shipping dimensions (lxwxh) 1,200 x 980 x 760 mm / 47.24 x 38.58 x 29.92 inches shipping weight from factory 151kg (333lbs) standard accessories power cord...

  • Page 421

    A. Specifications a.2 specifications of the hdf w26 overview projector type wuxga 3-chip dlp digital projector technology 0.96" dmd™ x3 resolution 1,920 x 1,200 brightness 26,000 center lumens / 24,000 ansi lumens* contrast ratio 1,900:1 (standard) / 2,200:1 (high contrast mode) brightness uniformit...

  • Page 422

    A. Specifications dissipation btu max. 15,593 btu/h dimensions (wxlxh) 707 x 1,025 x 548mm / 27.83 x 40.35 x 21.57 inches weight 99kg (218.25lbs) shipping dimensions (lxwxh)1,200 x 980 x 760 mm / 47.24 x 38.58 x 29.92 inches shipping weight from factory 151kg (333lbs) standard accessories power cord...

  • Page 423

    A. Specifications a.3 specifications of the hdf w30 flex overview projector type wuxga 3-chip dlp digital projector technology 0.96" dmd™ x3 sealed dlp core resolution 1,920 x 1,200 - 16:10 aspect ratio brightness 30,000 center lumens / 28,000 ansi lumens* contrast ratio 1,900:1 (standard) / 2,200:1...

  • Page 424

    A. Specifications certifications ul60950-1 and en60950-1,fcc rules & regulations,part 15 class a and ce en55022 class a,rohs warranty 3 years standard, extendable up to 5 years * +/- 10% 420 r5905158 hdf series 08/12/2016.

  • Page 425: Rohs

    A. Specifications a.4 technical regulations certificates image a-1 eac mark 10 image a-2 rohs rohs image a-3 rohs ok image a-4 ce mark r5905158 hdf series 08/12/2016 421.

  • Page 426

    A. Specifications 422 r5905158 hdf series 08/12/2016.

  • Page 427: B. Dimensions

    B. Dimensions b. Dimensions overview • dimensions of the hdf series projector • dimensions of the hdf series flight case r5905158 hdf series 08/12/2016 423.

  • Page 428

    B. Dimensions b.1 dimensions of the hdf series projector dimensions 730 250 520 643 14.8 13 0 14 8 14 8 480 485 459 485 643 676.1 771.1 771. 1 104 0 598. 05 483. 5 512. 6 310. 5 47. 5 115 25 78. 05 47. 5 43 .5 (+ 9) image b-1 dimensions given in millimeters. 424 r5905158 hdf series 08/12/2016.

  • Page 429

    B. Dimensions point of gravity 233 359 224. 5 image b-2 dimensions given in millimeters. R5905158 hdf series 08/12/2016 425.

  • Page 430

    B. Dimensions b.2 dimensions of the hdf series flight case dimensions 1194 66 0 81 7. 5 80 8 1175 819 800 image b-3 dimensions given in millimeters. 426 r5905158 hdf series 08/12/2016.

  • Page 431: C. Standard Source Files

    C. Standard source files c. Standard source files r5905158 hdf series 08/12/2016 427.

  • Page 432

    C. Standard source files 428 r5905158 hdf series 08/12/2016.

  • Page 433

    C. Standard source files c.1 table overview table overview the following standard image files are pre-programmed in the projector. Name 7 fvert hz 8 fhor khz 9 fpix mhz 10 ptot 11 pact 12 ltot 13 lact 14 640x350@85 85,079 37,860 31,500 832 640 445 350 640x400@85 85,079 37,860 31,500 832 640 445 400 ...

  • Page 434

    C. Standard source files name 7 fvert hz 8 fhor khz 9 fpix mhz 10 ptot 11 pact 12 ltot 13 lact 14 1400x1050@60 59,979 65,317 121,751 1864 1400 1089 1050 1400x1050@75 74,866 82,277 155,998 1896 1400 1099 1050 1400x1050@85 84,958 93,879 179,497 1912 1400 1105 1050 1400x1050rb@60 59,946 64,742 100,997 ...

  • Page 435

    C. Standard source files name 7 fvert hz 8 fhor khz 9 fpix mhz 10 ptot 11 pact 12 ltot 13 lact 14 hd-1920x1080@50p 50,000 56,250 148,500 2640 1920 1125 1080 hd-1920x1080@60p 60,000 67,500 148,500 2200 1920 1125 1080 video525 59,940 15,734 13,500 858 720 262 242 video525p 59,940 31,469 27,000 858 720...

  • Page 436

    C. Standard source files 432 r5905158 hdf series 08/12/2016.

  • Page 437: D. Dmx Chart

    D. Dmx chart d. Dmx chart overview • dmx chart, basic • dmx chart, full • dmx chart, extended r5905158 hdf series 08/12/2016 433.

  • Page 438

    D. Dmx chart d.1 dmx chart, basic overview chan- nel function value default action 0 - 5 mechanical shutter closed 1 intensity 6 - 255 255 electronic contrast on output 2 function select 0 - 7 no function 8 - 15 activate layout 1 (main full screen) (if held for 2 seconds) 16 - 23 activate layout 2 (...

  • Page 439

    D. Dmx chart d.2 dmx chart, full overview chan- nel function value default action 0 - 5 mechanical shutter closed 1 intensity 6 - 255 255 electronic contrast on output 2 brightness 0 - 255 128 adjusts the brightness between 0 and 100% on input 3 contrast 0 - 255 128 adjust the contrast between 0 and...

  • Page 440

    D. Dmx chart d.3 dmx chart, extended overview chan- nel function value default actions 0 - 5 mechanical shutter closed 1 intensity 6 - 255 255 electronic contrast on output 2 brightness 0 - 255 128 adjusts the brightness between 0 and 100% on input 3 contrast 0 - 255 128 adjusts the contrast between...

  • Page 441

    E. Stacking hdf series projectors e. Stacking hdf series projectors general three interlocking adapters at the top and at the bottom of the hdf series projector allows an easy and fast stacking without using extra tools or accessories. W arning : maximum stack three (3) hdf series projectors in a ta...

  • Page 442

    E. Stacking hdf series projectors e.1 stacking hdf series projectors how to stack hdf series projectors ? 1. Turn in the four feet of the projector you want to stack. 2. Place the projectors on top of each other. Ensure that all three interlocking pins (a) match with their corresponding interlocking...

  • Page 443

    E. Stacking hdf series projectors a) release the safety hook (h) at both sides of the lowest projector and guide the safety cable around its carrying handle (c) as illustrated. H c image e-3 safety cable b) guide the safety cable around the carrying handle of the projector above and clasp the safety...

  • Page 444

    E. Stacking hdf series projectors d c b a image e-5 opening interlocking adapter w arning : never open an interlocking adapter of a stacked projector which is still suspended. First place the stacked projectors on the floor. 440 r5905158 hdf series 08/12/2016.

  • Page 445: Rotation

    E. Stacking hdf series projectors e.2 aligning stacked hdf series projectors necessary tools 8 mm allen key. How to align two stacked hdf series projectors ? 1. Make sure that the internal hatch pattern projected by the reference projector is sharp and has a perfect rectangle outline. If this is not...

  • Page 446

    E. Stacking hdf series projectors 6. Shift the hatch pattern horizontally and vertically until the outline of the hatch pattern is most symmetrically placed with respect to the reference hatch pattern. Note: note that the “shift” function is motorized, which means that you have to access the project...

  • Page 447

    F. Environmental information f. Environmental information overview • disposal information • rohs compliance • production address • importers contact information r5905158 hdf series 08/12/2016 443.

  • Page 448

    F. Environmental information f.1 disposal information disposal information waste electrical and electronic equipment this symbol on the product indicates that, under the european directive 2012/19/eu governing waste from electrical and electronic equipment, this product must not be disposed of with ...

  • Page 449

    F. Environmental information f.2 rohs compliance 中国大 陆 rohs (information for china rohs compliance) 根据中国大 陆《电器电子产品有害物质限制使用管理办法》（也称为中国大陆rohs）， 以下部分列出了barco产品中可能包含的有毒 和 /或有害物 质的名称和含量。中国大陆rohs指令包含在中国信息产业部mcv标准：“电子信息产品中有毒物质的限量要求”中。 according to the “management methods for the restriction of the use of h...

  • Page 450

    F. Environmental information [republic of turkey: in conformity with the weee regulation] 446 r5905158 hdf series 08/12/2016.

  • Page 451

    F. Environmental information f.3 production address factories barco nv noordlaan 5, b-8520 kuurne (belgium) barco visual (beijing) electronics co. Ltd. 巴可 伟视（北京）电子有限公司 no.16 changsheng road, changping district, 102200, beijing, p.R.C 北京市昌平区中 关村科技园区昌平园昌盛路16号 邮政编码：102200 made in information the made i...

  • Page 452

    F. Environmental information f.4 importers contact information contact to find your local importer, contact barco directly or one of barco’s regional offices via the contact information given on barco’s web site, www.Barco.Com . 448 r5905158 hdf series 08/12/2016.

  • Page 453

    Revision sheet to: barco nv/documentation president kennedypark 35, 8500 kortrijk, belgium phone: +32 56.36.82.11, fax: +32 56.36.88.24 support: www.Barco.Com/en/support, web: www.Barco.Com from: date: please correct the following points in this documentation (r5905158/09): page wrong correct r59051...