Barco HDQ 4K35 Quick Start Manual

R5905854 Rev. 00

IMPORTANT

• Remove the lens before transporting 

the projector.

• Remove lamp house before 

transporting the projector.

• To save lamp lifetime, first switch the 

projector to standby mode and wait 

until the after cooling is finished to 

switch off the main power.

• Ensure that the projector is operating 

with clean filters.

• Do not block the ventilation in and 

outlets.

• Laser light can cause severe damage 

to the DMD. This damage is not 

covered by warranty.

Printed on FSC certified paper (www.fsc.org)

HDQ 4K35

Quick start guide

Mounting the lens

Additional vertical shift

Mounting the lamp house

A

B

1

1

• Remove the plastic cap in the lens    

  opening.

• Place lens holder in unlock position.       

  Handle A towards socket B.

• Gently insert the lens in such a way that               

  the lens connector matches the socket B.

• Insert the lens until the connector seats  

  into the socket.

• Secure the lens in the lens holder.  Move  

  handle A into the lock position (away  

  from socket B).

• Check if lens touches the front plate   

  of the lens holder.

• Check if the lens is really secured by  

  trying to pull the lens out of the lens  

  holder.

• Place the 2 lens fixation brackets (1)  

  into position and secure with a nut on  

  each bracket.

1

2

2

• To extend lens shift in a specific     

direction.

• Loosen the 4 screws (1) until 

central part of lens holder 

becomes loose.

• Shift the central part up or 

down.

• Lowermost, middle and 

uppermost shift positions are 

marked on the lens holder (2).

• Tighten the 4 screws.

1

1

2

3

1

Before installing the Lamp 

House, disconnect the power to 

the projector mains terminals 

and unplug the power cord at 

the UPS INLET for removal of all 

power from the projector.

• Remove housing on lamp house side.

• Grip the lamp house by both handles (1) 

• Place the lamp house on the base plate  

  inside the lamp compartment.

• Line up the foot of the lamp house with the  

  slots on the base (2).

• Push the lamp house fully in.

• Secure both retaining screws.

• Mount the housing

Quick Setup and operation

The following summarizes HDQ setup and operation. For 

errorfree installation always refer to the “User and Installation 

manual”.

Connect power. Ensure that the power is properly 

connected to the power input sockets. 

Y-

Δ (wye-delta) configuration possible.

Connect available sources to the appropriate input terminal. 

Switching on. Turn the mains switch to on.

Start up sequence starts. Communicator on touch panel 

starts up.

Press standby key on te local keypad.

Image of the latest selected input appears.

Adjust the lens settings via the local keypad keys or via 

Communicator.

Orientation of the unit is set as standard in table front 

projection mode. Change the projector set up with 

Communicator (Installation - Advanced settings - Misc. 

settings.

If geometrical distortion occurs this can be corrected with 

Communicator (Configurator - Screen).

Lamp management in Communicator (Installation - Lamp)

Switching off the unit can be done by pressing the STBY 

button for 3 sec. An aftercool up to 300 sec will start.

1

2

3

4

5

6

7

8

9

10

11

Communicator Touch Panel: Lens settings

To open the lens settings, click Configuration.

Select Lens.

Select Lens settings.

Adjust lens zoom, lens focus and lens shift.

1

2

3

4

Communicator Touch Panel: Orientation

To open the Image orientation settings, click Installation.

Select Advanced.

Select Misc. settings.

Select the correct Image orientation.

1

2

3

4

Communicator Touch Panel: Distortion

Communicator Touch Panel: Lamp manage

To adjust the distortion, click Configuration.

Select Screen.

Select Resizing or masking.

1

2

3

To manage the lamp, click Installation.

Select Lamp.

Select the desired lamp function.

1

2

3

C

M

Y

CM

MY

CY

CMY

K

R5905854_00_userguide.pdf   1   1/09/2014   11:04:29