1. DL manuals
  2. Baroness
  3. Lawn Mower
  4. LM180C
  5. Owner's Manual

Baroness LM180C Owner's Manual

Other manuals for LM180C: Owner's Operating Manual
Manual is about: 3-Unit Reel Mower

Summary of LM180C

  • Page 1

    Reel mower super mower owner's operating manual "required reading" read this manual and the owner's manual for the engine before using the machine. Serial no.15001 㨪 original instructions ver.1.0

  • Page 2

    Thank you for purchasing the baroness machine. This manual explains proper handling, adjustment, and inspection of your machine. Prior to use, carefully read this manual to thoroughly understand the contents for safe and correct operation. This machine has been shipped from the factory after compreh...

  • Page 3

    Read this manual carefully to ensure that you thoroughly understand how to properly operate and maintain this machine, and to avoid causing injury to yourself or others. The operator is responsible for operating the machine properly and safely. Do not perform maintenance on the machine other than th...

  • Page 4

    Lm180c introduction.

  • Page 5

    Safety ....................................................................... 1-1 safety management ............................................... 1-2 for safe operation ................................................. 1-2 training ....................................................................

  • Page 6

    Lm180c contents 2.

  • Page 7

    Safety management ....................................... 1-2 for safe operation ......................................... 1-2 training ........................................................... 1-2 before operating the machine ....................... 1-2 when operating the machine ...................

  • Page 8

    This machine met cen standard en 836: 1997 (if the specified label is affixed) for ride-on bunker rakes at the time of production. Improper use or maintenance may result in injury or death. To prevent an accident, be sure to follow the safety precautions described below and always pay attention to t...

  • Page 9

    Damaged, become dirty, or peel off, please replace them with new ones. Tighten any nuts, bolts, or screws that become loose to ensure that the machine is always operated under safe conditions. Evaluate the terrain to determine what accessories and attachments are needed to properly and safety perfor...

  • Page 10

    Use care when approaching blind corners, shrubs, trees, or other objects that may obscure your vision. When using attachments, never direct the discharge at bystanders or allow anyone near the machine while it is operating. Do not crawl under the machine while it is in operation. Before backing up, ...

  • Page 11

    When filling the tires with air, do not allow the air pressure in the tires to exceed the specified maximum. Check that all nuts, bolts, and screws are properly tightened to ensure that the machine is always operated under safe working conditions. Keep all parts in good working condition and all har...

  • Page 12

    Lm180c safety page 1-6 maintenance and storage.

  • Page 13

    Sound pressure .............................................. 2-2 sound pressure level lm180c sound pressure level page 2-1.

  • Page 14

    Sound pressure this machine was confirmed to have a continuous a-weighted sound pressure level of 93 db (a) by measuring identical machines in accordance with the procedure specified in directive en836:1997/ec. Lm180c sound pressure level page 2-2 sound pressure.

  • Page 15

    Sound power ................................................... 3-2 so und po we r leve l lm180c sound power level page 3-1.

  • Page 16

    Sound power this machine was confirmed to have a sound power level of 105 dba/lpw by measuring identical machines in accordance with the procedure specified in directive 2000/14/ec. Lm180c sound power level page 3-2 sound power.

  • Page 17

    Hand-arm vibration ........................................ 4-2 whole body vibration ..................................... 4-2 vibr ation level lm180c vibration level page 4-1.

  • Page 18

    Hand-arm vibration this machine was confirmed to transmit a maximum vibration level of 3.63 m/s 2 to hands and arms by measuring identical machines in accordance with the procedure specified in iso 5349-1, 2001 ࡮5349-2, 2001. Whole body vibration this machine was confirmed to transmit a maximum vibr...

  • Page 19

    About the safety labels and operation labels ........... 5-2 safety labels and ope ration labels lm180c safety labels and operation labels page 5-1.

  • Page 20

    About the safety labels and operation labels warning safety labels and operation labels are attached to this machine. Make sure that they are preserved in their entirety. If they are damaged, become dirty, or peel off, replace them with new ones. Part numbers for labels that need to be replaced are ...

  • Page 21

    Waste disposal ............................................... 6-2 about the waste disposal .............................. 6-2 disposal lm180c disposal page 6-1.

  • Page 22

    Waste disposal about the waste disposal make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations. (e.G. Waste oil, antifreeze batteries, rubber products, and wires etc.) lm180c disposal page 6-2 waste disposal.

  • Page 23

    Specifications ................................................. 7-2 names of portions .......................................... 7-3 positions of the decals (warning and instruction) ........... 7-3 warning and instruction decals ................... 7-4 product overview lm180c product overview page...

  • Page 24

    Specifications model lm180c dimensions total length 215 cm total width during operation 208 cm during transport 185 cm total height seat 107 cm handle 102 cm weight 387 kg minimum turning width 230 cm engine model subaru eh30b type air-cooled 4-cycle vertical ohv-type gasoline engine total displacem...

  • Page 25

    Names of portions 1 5 4 3 9 b 8 6 a 2 7 11 10 12 14 13 quwxcl-002 names of portions_001 1 handle 2 traveling clutch lever 3 change lever 4 parking brake lever 5 left mower unit 6 diff-lock pedal 7 reel rotation lever 8 engine stop switch 9 throttle lever 10 box 11 brake pedal 12 right mower unit 13 ...

  • Page 26

    Warning and instruction decals 1 2 3 1 qigqnx-009 lm180c-1001z0 sticker, operation warning read the owner's operating manual. Danger danger flying objects - any people other than the operator must keep a safe distance from the machine. Danger danger rollover - do not work on any slopes of 18 degrees...

  • Page 27

    5 check for leakage from hoses and fittings. Shut off fuel valve when engine is not in use. 1 2 3 4 5 7 6 qigqnx-013 r073-20057-60 decal, engine warning read manual. Exhaust gas is poisonous. Do not operate in an unventilated room or enclosed area. Stop the engine before refueling. Fire, open flame ...

  • Page 28

    Lm180c product overview page 7-6 warning and instruction decals.

  • Page 29

    Inspection before use ................................... 8-2 inspection of reel cutter (cutting cylinder) ........... 8-2 inspection of air cleaner ................................ 8-2 inspection of tires .......................................... 8-3 inspection of parking brake ......................

  • Page 30

    Inspection before use be sure to perform inspection before you start operating the machine so that you will be able to take advantage of its optimum performance for a long period of time. Inspection of reel cutter (cutting cylinder) the reel cutter (cutting cylinder) may become dull due to frequent ...

  • Page 31

    1 2 yt4sup-002 cleaning of air cleaner_002 1 element 2 urethane foam inspection of tires check the pneumatic pressure of the tires. Make sure that there are no cracks, damage or abnormal wear on the tires. Tire size pneumatic pressure front wheel (4.00 - 5) 200 kpa 㧔2.0 kgf/ছ 2 㧕 rear wheel 8.50 - 8...

  • Page 32

    Important do not mix different types of engine oil. Be sure to use the engine oil that is classified as api service grade sf or higher and that feature sae viscosity appropriate for your operating environment (ambient temperature). Through the oil filling port, fill the engine oil. Check the oil lev...

  • Page 33

    1 oil filling port 2 oil level plug 3 drain plug filling of transmission oil important do not mix different types of transmission oil. Be sure to pour the gear oil for automobiles that is classified as sae viscosity grade #90, into the transmission. Through the oil filling port, fill the transmissio...

  • Page 34

    Fuel supply if the fuel gauge located on the fuel tank indicates a level close to e (empty), supply lead-free gasoline for automobiles at your earliest convenience. The fuel tank capacity is approximately 6.0 dm 3 (6.0 liters). Lm180c handling instructions page 8-6 inspection before use.

  • Page 35

    Tightening torques standard tightening torques bolts and screws unless otherwise instructed, tighten bolts or nuts by the specified torque using an appropriate tool. Excessive tightening of a screw may cause it to become loose or damaged. The appropriate tightening torque depends on factors such as ...

  • Page 36

    Nominal diameter heat-treated screws strength category: 8.8 strength category: 10.9 8 t 8.8 8 tib3yb-002 11t 10.9 11 tib3yb-003 n-m kgf-cm lb-in n-m kgf-cm lb-in m5 5 - 7 50.99 - 71.38 44.26 - 61.96 7 - 10 71.38 - 101.97 61.96 - 88.51 m6 8 - 11 81.58 - 112.17 70.81 - 97.36 14 - 18 142.76 - 183.55 12...

  • Page 37

    Portion code part name tightening torque thread locking adhesive n-m kgf-cm lb-in mow er bed knife (bottom blade) k0071000092 screw, heat-treated flathead m10-20 29 - 38 295.71 - 387.49 256.68 - 336.34 㧙 front roller k0010100252 bolt, heat-treated m10-25 58 - 76 591.43 - 774.97 513.36 - 672.68 㧙 eng...

  • Page 38

    Adjustment of cutting height important the front wheel is provided to prevent the reel cutter (cutting cylinder) from damaging a convex portion of the lawn surface. Adjust the height so that the front wheel will not be grounded but raised by 10-20mm off the ground. The cutting height is adjusted by ...

  • Page 39

    Makes the engine stop unless it meets each of the following two conditions. The parking brake lever is pulled. The traveling clutch lever is in the "off" position. Operation of each section precautions for operating the machine caution drive the machine at such a speed that you can stop it immediate...

  • Page 40

    1 5zujec-002 lifting lever (for right/left mowers)_002 1 lifting lever lifting lever (for rear mower) for lowering the rear mower units, move the lifting lever down slowly with gripping the clutch lever. 1 2 817tmv-001 lifting lever (for rear mower)_001 1 clutch lever 2 lifting lever to raise the re...

  • Page 41

    1 traveling clutch lever 2 reel rotation lever operation of reel rotation lever caution unless both left and right mower units have been lowered all the way, you are not able to operate the reel rotation lever. To rotate the reel cutter (cutting cylinder) for the left and right mower units, pull the...

  • Page 42

    Cutting work procedure for cutting before starting the engine, check the following points. An operator must be sitting on the seat. The parking brake lever must have been engaged. The change lever must be in the neutral position. The traveling clutch lever must be in the "off" position. Start the en...

  • Page 43

    Maintenance schedule ................................... 9-2 maintenance precautions .............................. 9-3 specified values for maintenance ................. 9-3 main consumable parts ................................. 9-4 jacking up the machine ................................. 9-4 abou...

  • Page 44

    Maintenance schedule follow the maintenance schedule below. Caution use tools appropriate for each maintenance operation. ٤࡮࡮࡮inspect, adjust, supply, clean ٨࡮࡮࡮replace (first time) ٌ࡮࡮࡮replace maintenance item before work after w o rk every 8hrs . Every 5 0hrs. Every 1 00hrs. Every 200hrs. Every 2 ...

  • Page 45

    Maintenance item be fo re w o rk af ter work every 8hrs. Every 5 0hrs. Every 1 00hrs. Every 200hrs. Every 2 5 0hrs. Every 400hrs. Every 5 00hrs. Every year every 2 years every 4 years re mar ks main body hydraulic oil ٤ ٨ ٌ 100hrs (first time) hydraulic oil filter ٨ ٌ 100hrs (first time) hydraulic m...

  • Page 46

    Brake pedal 5 - 7 mm clearance between pedal stopper and brake pedal v -belt traveling clutch 5 mm clearance between rod-tension metal fitting and collar reel rotation lever 5 mm clearance between rod-tension metal fitting and collar left and right mowers 1 mm clearance between collar and mower lift...

  • Page 47

    Jack-up portion 2 1 4 5 6 3 rwyt62-011 jack-up portion_001 jack-up portion 1 front axle, center 2 front axle, right 3 front axle, left 4 transmission case, lower 5 transmission axle case, left 6 transmission axle case, right front axle, center rwyt62-012 jack-up portion_002 1. Front axle, right rwyt...

  • Page 48

    Transmission axle case, right rwyt62-017 jack-up portion_007 lubrication about the lubrication the moving parts of this machine need to be lubricated as a lack of grease on such parts could cause them to seize or be damaged. Grease the moving parts according to the maintenance schedule. Greasing poi...

  • Page 49

    Reel housing there is one point each on the left and the right of each unit. 8bq62b-058 greasing point_004 mower frame there is one point each on the left and the right mower units. 8bq62b-059 greasing point_005 mower lifting arm there is one point each on the left and the right mower units. 8bq62b-...

  • Page 50

    Rear mower oscillating metal part 8bq62b-065 greasing point_011 rear roller there is one point each on the left and the right of each unit. 8bq62b-066 greasing point_012 mower tension 8bq62b-067 greasing point_013 8bq62b-068 greasing point_014 9. 10. 11. Maintenance (mower) lapping of reel cutter (c...

  • Page 51

    1 newspaper 2 lapping powder 3 gel compound 4 brush 5 27 socket wrench note: mixing ratio for abrasive in volume is one part lapping powder to three or four parts oil. Caution before cutting newspaper as a test, be sure to stop the engine and wear gloves to protect your hands. Pay attention not to l...

  • Page 52

    For installing the front tires, reverse the removing procedure. Rear tires follow the steps below to remove the rear tires: loosen the bolts. Upekw4-001 rear tires_001 place the tire jack beneath the jack-up point of the rear wheel transmission area securely, then raise it until the tire lifts off t...

  • Page 53

    Adjust the clearance between the rod- tension metal fitting and the collar to be 5mm, when the traveling clutch lever is engaged. Tighten the adjusting bolt and make sure that the collar is fixed securely. 5 1 5 mm 4 3 2 l36w96-007 adjustment of belt tension_003 1 adjusting bolt 2 rod 3 traveling cl...

  • Page 54

    Tighten adjusting nut a and make sure that the rod is fixed securely. Raise the rear mower unit, then make sure that the reel cutter (cutting cylinder) will not rotate when the machine travels. 4 1 mm 3 2 1 l36w96-005 adjustment of belt tension_006 1 adjusting nut a 2 adjusting nut b 3 rod 4 rear mo...

  • Page 55

    1 4 4 5 2 3 3 ulabms-002 adjustment of parking brake_001 1 parking brake lever 2 brake wire 3 nut 4 wire adjustment metal fitting 5 brake drum note: you can also adjust the brake wire on the transmission side. Adjustment of brake if the brake is not applied effectively even if you depress the pedal ...

  • Page 56

    Adjust the wire so that the diff-lock wire and the diff-lock lever show a little play when the lever returns to its resting position under spring tension. Tighten the nut and fix the wire adjustment bracket completely. 1 3 2 4 5 6 4rnndz-001 adjustment of diff-lock wire_001 1 transmission 2 nut 3 wi...

  • Page 57

    1 nut 2 wire adjustment metal fitting 3 wire (to hook the mower) 4 right mower unit 5 hook metal fitting 6 bottom of the hook adjustment of wire to hook the rear mower loosen the nuts and move the wire adjustment metal fitting toward the center of the machine to increase the wire tension. Lower the ...

  • Page 58

    Lm180c maintenance page 9-16 long-term storage.

  • Page 61

    Tel : (0533)84-1390 fax : (0533)89-3623 head office 1-26, miyuki-cho, toyokawa, aichi-pref. 442-8530 japan. Lm180c--um--gbz/11d-00-s.K.