- DL manuals
- Bartell
- Saw
- BSM1402
- Owner's Manual
Bartell BSM1402 Owner's Manual
Summary of BSM1402
Page 1
Www.Bartellglobal.Com doc. # oi-b19042 orig. Rel. – 02/2017 curr rev. - 00 bartell morrison inc. 375 annagem blvd., mississauga, on l5t 3a7 telephone: 1-647-953-4100 fax: 1-647-953-4101 masonry saw bsm1402 owner’s manual.
Page 2
Bsm1402 masonry saw oi – b19042 owner ’s manual 1 bartell morrison inc. 375 annagem boulevard mississauga, ontario, canada l5t 3a7 tel: (647) 953-4100 fax: (647) 953-4101 bartell morrison usa llc 200 commerce drive, unit a freehold, nj, usa 07728 tel: (848) 225-8100 fax: (848) 225-8101 spe internati...
Page 3: Safety Precautions
Bsm1402 masonry saw oi – b19042 owner ’s manual 2 safety precautions danger explosion hazard never operate the machine in an explosive atmosphere, near combustible materials or airborne dust, or in areas if inadequate ventilation. Caution rotating hazard never place hands or fingers inside safety gu...
Page 4: Table Of Contents
Bsm1402 masonry saw oi – b19042 owner ’s manual 3 table of contents warranty information 4 safety information 5 features 7 specifications 7 health warning 8 unpacking 8 set up 9 s aw s tand f oldable l egs 9 assembly and operation 10 b l ade i nstall ation 10 w ater p ump i nstallation 10 w heel i n...
Page 5: Warranty Information
Bsm1402 masonry saw oi – b19042 owner ’s manual 4 warranty information all products sold by bartell morrison inc. And bartell morrison (usa) llc (the “company”) are warranted against defects in materials and/or workmanship for a period of 12 months; excluding the normal wear on wearing components an...
Page 6: Safety Information
Bsm1402 masonry saw oi – b19042 owner ’s manual 5 safety information before using this equipment, study the entire owner ’s manual to become familiar with its operation. Do not allow untrained or unauthorized personnel, especially children, to operate this equipment. Use only factory authorized part...
Page 7
Bsm1402 masonry saw oi – b19042 owner ’s manual 6 behavior of the machine) must be reported to the supervisor. If necessary, stop the machine at once and secure it. M. In the case of a malfunction, stop the machine immediately and secure it. Fix the problem as soon as possible. N. To stop and start ...
Page 8: Features
Bsm1402 masonry saw oi – b19042 owner ’s manual 7 features specifications motor max. Blade capacity cutting depth weight dim ensions 2 hp, 115-120 v, 60 hz, 3420 rpm 14 ” 4-1/2 ” 207 lbs length: 40.5 ” width: 23.2 ” height: 31.7 ” heavy duty power switch prevents the motor from overheating and prote...
Page 9: Health Warning
Bsm1402 masonry saw oi – b19042 owner ’s manual 8 health warning some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead...
Page 10: Set Up
Bsm1402 masonry saw oi – b19042 owner ’s manual 9 set up saw stand foldable legs 1. To deploy the foldable legs, unscrew the wing bolts located at the corner of the frame of the leg to be deployed. Only unscrew the wing bolts far enough so that the leg is movable. Do not remove the wing bolts. 2. St...
Page 11: Assembly And Operation
Bsm1402 masonry saw oi – b19042 owner ’s manual 10 assembly and operation blade installation 1. Open the blade nut door found on the blade guard by rotating it. Using the supplied wrench, loosen the nut. 2. Remove the nut and the outer flange. 3. Install a new blade. Make sure the blade rotation arr...
Page 12
Bsm1402 masonry saw oi – b19042 owner ’s manual 11 wheel installation 1. Wheel assembly can be installed on the frame or the rear folding legs (see figure 6). 2. To remove the wheel assembly, slide the spring pin out of its current slot and pull the wheel out. Put it in the desired location and rein...
Page 13
Bsm1402 masonry saw oi – b19042 owner ’s manual 12 performing straight cuts 1. Set the rip guide at the desired location on the ruler guide and tighten the threaded knob. Make sure the rip guide is firmly tightened to avoid slippage. 2. After the rip guide is positioned for the desired cut, place th...
Page 14: Warning:
Bsm1402 masonry saw oi – b19042 owner ’s manual 13 setting the cutting depth blade diam eter cutting depth 10 ” 2 ” 12 ” 3 ⅜” 14 ” 4½ ” warning: setting the blade too low may damage the cutting table and if set too high, the blade may grab the material being cut, possibly causing injury to the opera...
Page 15: Proper Blade Use
Bsm1402 masonry saw oi – b19042 owner ’s manual 14 proper blade use dos don’ts wet cut blades • inspect blades daily for cracks or uneven w ear. • alw ays use appropriate blade for material being cut. • inspect arbor shaft for uneven w ear before mounting blade. • alw ays use blades w ith the correc...
Page 16: Care And Maintenance
Bsm1402 masonry saw oi – b19042 owner ’s manual 15 care and maintenance warning: for your safety, before performing any maintenance on the saw turn off the power switch and unplug the power cord. General rules • always clean the machine before performing any maintenance/repair. • before performing a...
Page 17
Bsm1402 masonry saw oi – b19042 owner ’s manual 16 • rinse the immersion pump with fresh water to prevent the water pump from clogging with residual dirt. After wet cleaning and b efore using the machine again: • connect the machine to an electric power outlet equipped with a “gfci” safety power bre...
Page 18
Bsm1402 masonry saw oi – b19042 owner ’s manual 17 4. Take the lid off the pump. Be careful not to damage or lose the gasket underneath. 5. Clean the pump lid. 6. Remove all dirt and incrustations from the pump wheel. 7. Check whether the pump wheel can be easily turned. 8. Then reassemble the immer...
Page 19
Bsm1402 masonry saw oi – b19042 owner ’s manual 18 realignment method 1: this procedure deals with the most common source of misalignment that occurs when the guide rails are not parallel with the blade. 1. Set the cutting depth such that the blade passes through the table, not over. 2. Place a stra...
Page 20
Bsm1402 masonry saw oi – b19042 owner ’s manual 19 a. If the straight edge only touches the blade when the table is positioned midway along the rail or at the ends of the rail, then the rail may be deformed (i.E. Bowed) (figure 10). Perform test cuts to determine if the rail should be replaced. Typi...
Page 21
Bsm1402 masonry saw oi – b19042 owner ’s manual 20 4. After adding shim(s), mount the table back onto the guide rails. Realign the table to the blade using method 1. Check to see if any shifting persists. A shift tolerance of 0.5mm is allowed. A shift in excess of that will require further adjustmen...
Page 22: Electrical Specifications
Bsm1402 masonry saw oi – b19042 owner ’s manual 21 7. The square face closest to the blade should be parallel to the blade. If it is not, raise/lower both flat rollers until it is level. 8. The table should now be level and square with the blade. If it is not repeat previous steps 2 thru 7. 9. Mount...
Page 23: Warning:
Bsm1402 masonry saw oi – b19042 owner ’s manual 22 extension cord chart electrical wiring diagram warning: to avoid permanent motor damage, you must use the correct extension cord. Never use more than one extension at a time. Follow the chart below for proper size. Wire gauge length of cord no. 12 2...
Page 24: Troubleshooting
Bsm1402 masonry saw oi – b19042 owner ’s manual 23 troubleshooting problem possible cause solution machine does not run w hen sw itched on pow er cord not properly fixed/ plugged in check that the machine is properly connected to the pow er supply pow er cord defective have the pow er cord checked, ...
Page 25
Bsm1402 masonry saw oi – b19042 owner ’s manual 24 drive motor no longer runs at rated speed (rpm) have the motor checked by a qualified electrician and have it replaced if necessary problem possible cause solution insufficient flow of cooling w ater or no cooling w ater at all the pump draw s air f...
Page 26
Bsm1402 masonry saw oi – b19042 owner ’s manual 25 shaft of motor causes w obbling have bearings of the motor or the motor replaced overheating ensure optimum flow of cooling w ater cracks in or near the diamond segment saw blade too hard use a softer blade fixed flange is w orn out replace the fixe...
Page 27
Bsm1402 masonry saw oi – b19042 owner ’s manual 26 check the receiving flange and have it replaced if necessary saw blade show s blooming colors saw blade overheating due to a lack of cooling w ater ensure an optimum flow of cooling w ater lateral friction w hen cutting the material feed is too high...
Page 28
Www.Bartellglobal.Com bartell morrison inc. 375 annagem boulevard mississauga, ontario, canada l5t 3a7 tel: 1-647-953-4100 fax: 1-647-953-4101 bartell morrison (usa) llc 200 commerce drive, unit a freehold, new jersey, usa 07728 tel: 1-848-225-8100 fax: 1-848-225-8101 innovatech 832 80th street sw e...