- DL manuals
- Batca
- Home Gym
- fusion 4
- Owner's Manual
Batca fusion 4 Owner's Manual
Summary of fusion 4
Page 1
Www.Batcafitness.Com fusion 4 functional trainer june 2014 revision 2 serial number here date of purchase owner’s manual functional trainer 1207 new hope road, raleigh, nc - 919.255.1233 - www.Batcafitness.Com.
Page 2
Batca fitness systems 2 fusion 4 functional trainer __________ page instructions 2 parts listing 3 hardware comparison 4-7 pre-assembly instructions 8 main frame assembly 9-12 cable routing 13-14 accessories holders and shrouds 15 __________ page cable tension and adjustments 16 weight stack decals ...
Page 3: Tools Required
Www.Batcafitness.Com 3 fusion 4 functional trainer frame components accessories item no. Part no. Description qty 22 bfm-51173 weight stack pull pin 2 23 bfc-10103 strap handle 2 item no. Part no. Description qty 1 bfm-11052 right side height adjustment 1 2 bfm-10400 swivel pulley holder 2 3 bfm-107...
Page 4
Batca fitness systems 4 fusion 4 functional trainer bolt length note: bolt length is measured from the underside of the head of the bolt..
Page 5
Www.Batcafitness.Com 5 fusion 4 functional trainer.
Page 6
Batca fitness systems 6 fusion 4 functional trainer.
Page 7
Www.Batcafitness.Com 7 fusion 4 functional trainer.
Page 8
Batca fitness systems 8 fusion 4 functional trainer pre-assembling instructions note: it is important to position the upper body and the lower body stations accordingly. Make sure they are approximately 5 foot 1 inch apart by measuring from the inside of the rear base on each machine. Also make sure...
Page 9
Www.Batcafitness.Com 9 fusion 4 functional trainer step 1: item # part # description qty 1 bfm-11051 right side height adjustment 1 2 bfm-10400 swivel pulley holder 1 3 bfm-10758 short base frame (right side) 1 4 bfm-52519 selector tube 1 5 bfm-10760 long base frame (left side) 1 6 bfm-10772 right s...
Page 10
Batca fitness systems 10 fusion 4 functional trainer figure 2 step 2: all flat washers and nylocks are 3/8” unless otherwise noted. Do not tighten hardware until next step. Item # part # description qty 7 bfm-51456 pulleyholder/support plate 2 8 bfm-10757 upper support brace (right) 1 9 bfm-10756 ex...
Page 11
Www.Batcafitness.Com 11 fusion 4 functional trainer figure 3 item # part # description qty 10 bfm-10751 front angle bracket 1 11 bfm-51457 rear angle bracket 1 29 bfh-50323 fhscs 3/8”-16 x 3” 2 30 bfh-51184 fhscs 3/8”-16 x 5 1/4 2 40 bfh-50146 3/8” flat washer 4 41 bfh-50157 3/8” nylock 4 step 3: ma...
Page 12
Batca fitness systems 12 fusion 4 functional trainer figure 4 step 4: item # part # description qty 12 bfm-10752 guide rod holder 1 13 bfm-10299 top plate 1 14 bfm-51493 guide rod 2 15 bfm-50256 weight stack plate 19 16 bfm-50529 rubber donut 2 22 bfm-51173 weight stack pull pin 1 31 bfp-51747 shcs ...
Page 13
Www.Batcafitness.Com 13 fusion 4 functional trainer step 5: figure 5 item # part # description qty 17 bfm-10425 free floater (male) 1 23 bfc-10103 strap handle 1 24 cab-13033 functinal trainer cable 1 27 bfp-52394 shcs 3/8”-16x 2-1/2” 3 32 bfh-50174 4 1/2” pulley 4 33 bfh-50173 3 1/2” pulley 2 34 bf...
Page 14
Batca fitness systems 14 fusion 4 functional trainer start here 269 11/16” cab-13033 step 5 continued: note: cables cab-13033 has a removable cable strap (bfh–50227) end to make cable routing easier. The cable strap ends can be found packaged with the hardware..
Page 15
Www.Batcafitness.Com 15 fusion 4 functional trainer figure 6 item # part # description qty 18 bfm-10762 short bar/ankle strap holder 1 19 bfm-51494 front shroud 1 20 bfm-51082 rear shroud 1 21 bfm-10763 rope/long bar holder 1 36 bfp-51752 shcs 3/8”-16 x 2 1/4” 1 38 bfp-52401 bhscs 3/8”-16 x 1/2” 4 3...
Page 16
Batca fitness systems 16 fusion 4 functional trainer adjust cables to proper tension from any of the locations shown below. Note: all cables with threaded adjustable ends must have at least 1/2” of the threads threaded in to its counterpart. It is very important that the 1/2” jam nut be wrench tight...
Page 17
Www.Batcafitness.Com 17 fusion 4 functional trainer clean guide rods with a lint-free cloth and apply a thin layer of silicon lubricant (part # bfh-50262) to each guide rod. This will ensure a glass smooth performance from your weight stack. Weight stack decals: guide rod lubrication: 200lb stack (s...
Page 18
Batca fitness systems 18 fusion 4 functional trainer step 25: important - check these components before using gym: final assembly and troubleshooting wrench tighten the set screws on all threaded collars using an allen wrench, so that the set screws tighten against the shaft. Refer to step 1. Thread...
Page 19
Www.Batcafitness.Com 19 fusion 4 functional trainer batca fitness systems strives to give you the very best in quality, performance and safety through carefully engineered designs and excellent workmanship. In order to maintain this high level of quality the preventative maintenance schedule below s...
Page 20
Batca fitness systems 20 fusion 4 functional trainer what is covered for residential use: batca fitness systems warrants all of its products against defects in manufac- turing, materials and workmanship under normal use and service for one year from date of purchase including paint, chrome, upholste...
Page 21
Www.Batcafitness.Com 21 fusion 4 functional trainer the fusion without leg press has a layout dimension of 12’-11” (width) x 6’-7” (length) x 7’-2” (height). There should be a minimum of 18”, preferably 24”, of working space around the entire unit. Layout diagram without leg press.
Page 22
Batca fitness systems 22 fusion 4 functional trainer the fusion with leg press has a layout dimension of 14’-4” (width) x 6’-7” (length) x 7’-2” (height). There should be a minimum of 18”, preferably 24”, of working space around the entire unit. Layout diagram with leg press.