Bircher Reglomat ProLoop Operating Instructions - page 4
Manufacturer:
Bircher Reglomat AG
Wiesengasse 20
CH-8222 Beringen
Switzerland
www.bircher-reglomat.com
info@bircher.com
Telefon +41 (0)52 687 1111
Telefax +41 (0)52 687 1112
4
Changeover to simulations mode
Press «Sim1»
button
Press «Sim2»
button
Press «Sim2»
button
Press «Sim2»
button
Notes
Changeover to simulation mode:
Press the Sim1 + Sim2 buttons
simultaneously for 2 seconds.
Mode
Sim1
2 seconds
+
Data
Sim2
2 seconds
1
Simulation mode:
Activation of the loop with time
function
Mode
Sim1
1
Data
Sim2
1
Data
Sim2
2
Data
Sim2
2
L0 -
Activation of loop 1 with time function output 1
L1 -
Activation of loop 1 with time function output 2
- Loop 1
- Loop 2
Activation of the loop without
time function
Mode
Sim1
1
Data
Sim2
1
Data
Sim2
2
Data
Sim2
2
0
0 -
Activation of loop without time function output 1
0
0 -
Activation of loop without time function output 2
- Loop 1
- Loop2
Alarm output activation
Mode
Sim1
Data
Sim2
A0
-Switch off alarm relay
A1
-
Switch on alarm relay
Inductance of loop 1
Mode
Sim1
1
Measurement of the inductance, value in
µH
Inductance of loop 2
Mode
Sim1
2
Measurement of the inductance, value in
µH
Exiting simulation mode
Mode
Sim1
2 seconds
1
2
Return to function mode
The activation of the loops can only be simulated if loops are connected to the appropriate terminal!
The displays apply similarly for loop 2
If an error occurs, operating mode «A» and error display «E» light up alternately and an error code such as E 012 is displayed. The LED changes to flashing
red, the 4 most recent errors are stored and can be interrogated.
Display
E001
E002
E011
E012
E101
E201
E301
E302
E311
E312
Error
Interruption
Loop 1
Interruption
Loop 2
Short circuit
Loop 1
Short circuit
Loop 2
Under-
voltage
EPROM
Error
Loop 1
too large
Loop 2
too large
Loop 1
too small
Loop 2
too small
Briefly pressing the «Data» button shows the last of 4 errors on the display. Another short press switches to the error before that,
and so on. When the button is pressed for the 5th time, the device switches back to automatic mode. If you press the «Data» button
for 2 seconds during the query, all error messages are deleted. The figure shows memory slot 1 in which error 001 Interruption loop
1 has been stored (example).
ProLoop
ProLoop 11
Supply voltage /
Power consumption
24 VAC –20 % to +10%, max. 2 VA
24 VDC –10 % to +20%, max. 1.5 W
94–240 VAC ± 10%, 50/60, max. 2.9 VA
24 VAC –20% to +10%, max. 1.8 VA
24 VDC –10% to +20%, max. 1.3 W
115 VAC –15% to +10%, max. 3.5 VA
230 VAC –15% to +10%, max. 3.7 VA
Power consumption
max. 2 VA
24V 1.2 VA
Loop inductance
max. 40–1000 µH,
ideally 80–300 µH
max. 40–1000 µH,
ideally 80–300 µH
Loop connection wiring
max. 200 m 1,5 mm
2
min. 20x/m
max. 200 m 1,5 mm
2
min. twisted 20x/m
Loop resistance
Output relay (loop)
240 VAC/2 A AC1
240 VAC/2 A AC1
Output relay (alarm)
60 VAC, 0.3 A, AC1
–
Dimensions
22.5 x 94 x 88 mm (W x H x D)
36 x 74 x 88 mm (W x H x D)
Housing mounting
Direct DIN rail mounting
Mounting rail installation via 11-pin base ES 12
Connection type
Plug-in terminals
Screw terminals base ES 12
Protection class
IP 30
IP 20
Approvals, safety
See declaration of conformity at www.bircher-reglomat.com
See declaration of conformity at www.bircher-reglomat.com
Operating temperature
–20°C to +60°C
–20°C to +60°C
Storage temperature
–40°C to +70°C
–40°C to +70°C
Air humidity
Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen declares that the
Product, type: ProLoop, ProLoop 11
Model: 24VDACDC, 115VAC, 230VAC, 1-loop devices, 2-loop devices
Intended purpose: Programmable loop detector for controlling gates and barriers as well as for regulating and counting cars in parking areas
if used in accordance with the intended purpose, complies with the basic requirements acc. to:
R&TTE Directive, Appendix III 1999/5/EC
26
36
77
F
06
/1
0
5
Simulation mode
6
Troubleshooting
7
Reset
8
Most important technical data
9
Declaration of conformity
10
Contact data
Mode
Sim1
2 seconds
Reset 1 (recalibration)
The loop(s) is/are recalibrated.
Mode
Sim1
8 seconds
Data
Sim2
Reset 2 (factory setting)
All values are reset to the factory settings (see Table 4.11a).
The loop(s) is/are recalibrated.