BuildTrack Smoke Detector Quick Installation Manual
Quick Installation Guide
B-003-004, Platform Level, 1st Floor
Tower #10, ITC, Belapur Station Complex
CBD Belapur, Navi Mumbai - 400614, Ph.+91-22-61340350
Support: support@buildtrack.in|Sales: sales@buildtrack.in
www.buildtrack.in
Once the smoke detector has been installed, user can test the
working of the device in the following manner.
1.
Press the test button. The LED should flash every 1s
and the detector should produce a loud beep.
2. The detector can also be tested by blowing some
smoke in front of the detector to check if it is working
properly. Once it detects the smoke, the LED will flash
and the detector will beep which will stop after the
smoke disperses.
Operation Instructions
Take care of the following measures while using the sensor.
• Do not install it on moist ceiling or wall.
• Test it monthly
• Clean the sensor by soft brush once in six months to
ensure the efficient working of the product
• When the voltage of battery is low or the chamber is
dirty, the detector will beep every 40s. Change the
battery at this condition.
Troubleshooting & Safety Instructions
Photoelectric smoke detector works through the detection of smoke particles that reflects infrared light. Infrared
diodes placed in the special chamber detects this infrared light. When smoke enters the special chamber, the
density of infrared light increases and after it attains a certain density, the detector produces the alarm signal.
The detector can be upgraded to work wirelessly to generate sms or internet based alerts by connecting it to a
transmitter and BuildTrack controller.
BuildTrack
TM
is a registered trademark of Surmount Energy Solutions Pvt. Ltd.
© Copyright 2013: Surmount Energy Solutions Pvt. Ltd: All rights reserved
Key Features of the Product
Enhancement
Technical Specifications
Table 1: Technical Specifications
Description
Input Voltage
Static Current
Alarm Current
9V Battery
≤20μA
Operating Humidity
Operating Temperature
≤95%RH
(Non coagulating)
-100c to +500c
Alarm Mode
Sound &Flash Alarm
Unobstructed Effective
Transmitting Range
100 meter
Alarm Sound Level
≥85dB /m
Transmitting Frequency 315MHz or 433MHz
≤15mA
Coding Mode
2262/1527
Detecting Area
80 square meter
(installation height of
6m-12m)
60 square meter
(installation height less
than 6m)
Smoke Sensitivity
2.06%/FT (UL)
Dimension
Φ107*35mm
Specification
BuildTrack™ Smoke Detectors (also known as smoke alarms or smoke sensors) detect smoke in any space
where they are installed. These work independently by emitting a loud beep when any smoke is detected by it.
This is a solution that is intended primarily for kitchens, bedrooms and living rooms of hotels, residential
apartments, and hospitals, warehouse and laboratory locations, power rooms of buildings, control rooms and
store rooms etc.,
Model: BT-SDSA
Inside the box
1. Smoke Detector
2. Battery
3. Mounting Plate
4. Screws
Thank you for choosing this BuildTrack™ Product
Device Layout
Figure 1 : Device Layout
Figure 3 : Smoke Detector Connected to the Mounting Plate
Figure 2 : Connecting The Battery
Smoke Detector (Front)
Smoke Detector (Back)
Interlocking knobs fit here
Mounting Plate
Battery
Interlocking knobs
to attach sensor
to sensor plate
Holes for
inserting screws
Step 1:
Identify the placement location of the detector. For best results the smoke detector is usually placed
on the center of the ceiling.
Step 2:
Insert the battery into the battery holder and connect it to the battery connectors as shown in
figure 2.
Step 3:
Fix the mounting plate to the celling wall by fixing the screws through the holes available on the plate
as shown in
Figure1
. Tighten the screws using a screw driver.
Step 4:
Attach the smoke detector to the Mounting Plate using the interlocking knobs as shown in
Figure 3
.
Installation Instructions
Smoke Detector
Battery
Battery Connectors
Test button