Bullard Eclipse User Manual - Www.Bullard.Com
www.bullard.com
Eclipse
®
Thermal Imager
User Manual
NoTE
If the battery is inserted without first retracting the battery release switch,
the battery will not fully seat. If this occurs, remove the battery and follow
reload using the instructions above. The battery latch mechanism prevents
accidental battery release upon impact.
Charging and
Maintaining Batteries
If you purchased an Eclipse Powerhouse
with your Eclipse Thermal Imager, see the
enclosed Eclipse Powerhouse manual for
charging instructions. If you purchase a
PowerUp Charger/Conditioner/Analyzer
with your Eclipse Thermal Imager, see the
enclosed PowerUp manual for charging
instructions. If you purchased an Eclipse
Thermal Imager only, you received a
charging base.
To charge a battery in the charger included with your Eclipse, place it in the
charging base (Figure 6). A steady red light will indicate that the battery is
charging, while a steady green light will indicate a full charge. The system will
detect the full charge and will not overcharge the battery. A completely drained
battery takes up to three hours to fully recharge.
As with all batteries, your Bullard rechargeable battery will experience a slow
drain of its charge during storage. The amount of drain varies widely based on
storage conditions. To ensure adequate battery life, charge each of your batteries
every two weeks or, for best performance, keep your Eclipse and spare battery
charged in your vehicle in the Eclipse Powerhouse truck mount charger accessory
(part number: ECLPOWERHOUSE). If you are using a Powerhouse charger, follow
the instructions contained in the accompanying manual.
NoTE
Ensure that the charging base is receiving power from a source via either
the AC or DC power adapters. If you do not see the red LED illuminate when
you place a battery into the charger, the battery is not charging.
NoTE
New, fully charged NiMH batteries will provide a run time of more than three
hours. To extend the potential lifespan of your batteries, fully drain and
recharge each battery monthly. For best operational results, develop a clear
formalized plan for maintaining, charging, and replacing your batteries.
Retractable Strap
The Eclipse Thermal Imager fits easily into a turnout gear pocket for convenient
storage while crawling or working. Additionally, Bullard offers a retractable strap
that can be used with the Eclipse, so that it is always at the ready. The strap (part
number: ECLRETRACT), purchased separately, can be mounted to a D-ring on your
turnout gear coat and connected to the D-ring on the Eclipse.
Care Instructions
The Bullard Eclipse Thermal Imager requires little maintenance. For best results,
after each use:
• Clean the outside of the unit with mild soap or detergent.
• Wipe the lens with a soft cloth.
• Clean the display with a soft cloth.
• Check screw tightness on cover display.
• Store your thermal imager in the optional truck mount or in the delivery case
provided.
• All thermal imagers should be maintained using a proper program.
Cleaning the Lens
The Bullard Eclipse lens is recessed in an impact resistant bezel. The lens can be
cleaned with a soft cloth and soapy water as required.
Replacing the Video Display Cover Window
The display cover (Figure 7) has a scratch-resistant hard coating to minimize
marring. However, if heavy scratching or gouging does occur, the cover window
can be replaced. To do this, remove the
four Phillips head screws along the sides
of the window. Remove the plastic display
cover window and replace with a new
one (part number:ECLWINDOW). Do not
over-tighten.
Do not allow the metal contacts on the battery to come in contact with a
conductive surface, such as a metal table or another battery. While the Eclipse
is equipped with protective circuitry to prevent product damage, contact with
conductive surfaces can complete the battery circuit and cause the battery to
overheat or melt. Failure to observe this warning may result in permanent
battery damage, property damage and/or serious injury.
WARNING
The Eclipse Thermal Imager is extremely sensitive to intense, radiant heat
sources. Never point the Eclipse at the sun or any other source of extreme
radiant heat, as this could severely damage the thermal imager.
WARNING
Figure 7
Do not use solvents or paint thinners to clean your Bullard Eclipse Thermal
Imager, as they could permanently mar the surface or degrade the protective
properties of the casing.
Do not intentionally submerge the unit underwater or subject the unit to high-pressure
water. Follow care instructions described above.
Failure to observe these instructions may result in product damage.
Any damage caused by improper care is not covered under warranty.
CAUTIoN
Figure 6