1. DL manuals
  2. Bulldog Security
  3. Remote Starter
  4. DELUXE 12
  5. Installation And Owner's Manual

Bulldog Security DELUXE 12 Installation And Owner's Manual

Other manuals for DELUXE 12: Installation And Owner's Manual

Summary of DELUXE 12

  • Page 1

    Contents alarm and remote starter model deluxe 62 installation guide • owner’s guide technical assistance all tech personnel are expertly qualified to answer any technical questions. Technicians are available monday through friday from 9:00 a.M. Until 8:00 p.M. And saturday 10:00 a.M. Until 4:00 p.M...

  • Page 2

    System features system components 1 your system includes: 1-installation & operation guide 1-main control module 2-four button remote transmitter with slide protectors 1-(4) relay harness with relays 1-18-pin wire harness required tools 1-5 pin harness (door locks) 1-hood pin switch 1-extended range...

  • Page 3

    Technical assistance should you need help. First check our website at www.Bulldogsecurity.Com/wires.Htm or call our toll-free tech support hotline monday through friday 9am-8pm and saturday 10am-4pm est at 800-878-8007. You must give the following information: •name •telephone number with area code ...

  • Page 4

    Making wiring connections 4. Insert the wire from the unit through the hole as shown. 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie ...

  • Page 5

    4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 2. Twist upper wires together, twist lower w...

  • Page 6

    Accessory wire(s) that power the heater/blower motor (+12v in run or on positions) this wire is also in the main ignition switch harness usually located in the steering column. Make all connections as close to the ignition switch harness as possible. Most vehicles will have (1) accessory wire; howev...

  • Page 7

    6 hood pin switch this feature will keep the engine from starting or shut off the engine when the hood is opened. Locate a good chassis ground, if at all possible do not install the pin switch in the rain gutter. Drill a 5/16 hole, insert the pin switch into the hole and tighten. Check for the hood ...

  • Page 8

    7 trunk release output (optional part #775 required) locate the trunk release wire coming from the back of the trunk release switch. You must determine if your trunk release is a (+) positive or a (-) negative. (most trunk releases are (+) positive). Test for a (+) positive trunk release wire, clip ...

  • Page 9

    Connecting the 18-pin harness & 4-relay harness antenna placement control module antenna wire antenna tube 8 run the antenna wire up the windshield pillar on the driver’s side and across the top of the windshield tucking the antenna wire inside the headliner, behind the rearview mirror. Plug the red...

  • Page 10

    Factory anti-theft systems for general motors cars only system 1: passkey i and ii system (1985 and up). This system has a resistor pill in the key. Measure resistance of the pill using a test meter. A bypass module is available, part #vats-wr module. System 2: passlock i and ii system (1995 and up)...

  • Page 11

    How to use your remote transmitter 10 connecting door locks “type a” (+) positive (5-pin harness) note: connect the red with black stripe wire to +12v constant fused at 30 amps. Unlock lock green/black unlock green/white not used red/black blue/black lock blue/white not used keyless module +12v cons...

  • Page 12

    Installation programming instructions operator programming instructions 11 programming double crank time press and hold the brake, then press and hold button #3 (trunk) until the parking lights flash three (3) times. Release button #3. Press and release button #3, the parking lights will flash once....

  • Page 13

    Programming shock sensor on and off (see adjusting shock sensor) press and hold the brake, then press and hold button #4 (stop) until the parking lights flash four (4) times. Release button #4. Press and release button #2, the parking lights will flash once the shock sensor is now on. Press and rele...