1. DL manuals
  2. Bulldog Security
  3. Remote Starter
  4. DELUXE 12
  5. Installation And Owner's Manual

Bulldog Security DELUXE 12 Installation And Owner's Manual

Other manuals for DELUXE 12: Installation And Owner's Manual

Summary of DELUXE 12

  • Page 1

    Contents remote starter models deluxe 12 and deluxe 22 installation guide • owner’s guide technical assistance all tech personnel are expertly qualified to answer any technical questions. Technicians are available monday through friday from 9:00 a.M. Until 8:00 p.M. And saturday 10:00 a.M. Until 4:0...

  • Page 2

    System features system components technical assistance should you need help. First check our website at www.Bulldogsecurity.Com/wires.Htm or call our toll-free tech support hotline monday through friday 9am-8pm and saturday 10am-4pm est at 800-878-8007. You must give the following information: •name...

  • Page 3

    Before you begin making wiring connections 1. Strip back two inches of insulation on the wire from the keyless entry. 2. Strip back one inch of insulation on the wire you need to connect to. One inch of bare wire two inches of bare wire 2 precautions this system is designed for vehicles with power d...

  • Page 4

    4. Insert the wire from the unit through the hole as shown. 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together. Use this me...

  • Page 5

    Accessory wire(s) that power the heater/blower motor (+12v in run or on positions) this wire is also in the main ignition switch harness usually located in the steering column. Make all connections as close to the ignition switch harness as possible. Most vehicles will have (1) accessory wire; howev...

  • Page 6

    5 note: remove any paint below the spade connector. Factory bolt spade connector black ground wire brake input the brake wire is located on the switch near and above the brake pedal. The correct wire will show +12v only when the brake is pressed. Connect the blue with black stripe from the 18-pin ha...

  • Page 7

    6 mechanical neutral safety switch (rear wheel drive only) when installing a bulldog remote starter on gm vehicles or dodge dakotas built prior to 1996, you must: use the diagram below to create a circuit that will prevent the remote starter from starting the vehicle unless the key is removed from t...

  • Page 8

    7 connecting the 18-pin harness & 4-relay harness antenna placement control module antenna wire antenna tube factory anti-theft systems for general motors cars only system 1: passkey i and ii system (1985 and up). This system has a resistor pill in the key. Measure resistance of the pill using a tes...

  • Page 9

    Testing door locks testing: door locks there are three basic types: “type a” door lock test (most gms and some chryslers) probe both of your door lock wires going to the door lock switch usally located in the driver’s kick panel. Attach the clip end of your test light to a good chassis ground. Using...

  • Page 10

    9 “type c” reverse polarity (5-pin harness) note: you will need to cut factory wiring to make an end to end connection, see “making connections” on page 2-4. Power door lock motor lock unlock green/black unlock green/white unlock red/black blue/black lock blue/white lock keyless module +12v constant...

  • Page 11

    10 operator programming instructions programming door lock pulse length 3.5 (from .7 to 3.5 seconds) press and hold the brake, then press and hold button #3 (trunk) until the parking lights flash three (3) times. Release button #3 (trunk). Press and release button #1 (start), the parking lights will...

  • Page 12

    How to use your remote transmitter starting the vehicle with the remote transmitter press and release button #1 (start). The parking lights will flash once, confirming the car starter received the signal. The car will then start and the parking lights will turn on and remain on while the vehicle is ...