1. DL manuals
  2. Bulldog Security
  3. Remote Starter
  4. RS1200
  5. Installation And Owner's Manual

Bulldog Security RS1200 Installation And Owner's Manual

Other manuals for RS1200: Manual, Manual

Summary of RS1200

  • Page 1

    Contents remote starter models rs1200/rs1200e installation guide • owner’s guide technical assistance all tech personnel are expertly qualified to answer any technical questions. Technicians are available monday through friday from 9:00 a.M. Until 8:00 p.M. And saturday 10:00 a.M. Until 4:00 p.M. Ad...

  • Page 2

    System features system components technical assistance 1 required tools 2 four-button extended range remotely start your car to run the heater, air conditioning or defroster from an extended remote control distance. Keyless entry remotely locks and unlocks your power door locks. Trunk release/slidin...

  • Page 3

    Before you begin 2 precautions using your test probe congratulations, you have purchased one of the most advanced remote starter systems ever made. Your new remote starter is a technological breakthrough utilizing the most advanced, state-of-the-art technology and components. It is computer controll...

  • Page 4

    Making wiring connections 3 note: in most cases you should not cut your vehicle wire in two. 1. Strip back two inches of insulation on the wire from the remote starter. 2. Strip back one inch of insulation on the wire you need to connect to. 3. Separate the vehicle wire as shown. Make the separation...

  • Page 5

    4 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 2. Twist upper wires together, twist lower...

  • Page 6

    5 note: remove any paint below the spade connector. Factory bolt spade connector black ground wire 1. If your vehicle has only one (1) ignition wire, as most 1993 and older domestic and import vehicles do, connect the heavy gauge white wire to it. 2. If your vehicle has two (2) ignition wires, as mo...

  • Page 7

    6 neutral safety switch connecting the wiring harness parking lights (+12v only with parking lights on) turn the parking lights to the on position. (not your headlamps). Probe the wire(s) coming from your headlamp control switch. The correct wire will show +12v and the red light will glow bright onl...

  • Page 8

    7 antenna placement factory anti-theft systems optional connections control module antenna wire antenna tube antenna for best results, run the antenna (yellow wire with black tip from the back of the unit) as high up in the dash and as straight as possible. Do not place the antenna next to any metal...

  • Page 9

    8 on the switch and test the unlock wire. The correct wire will test (-) negative and the green light will glow bright. Release the unlock button and this wire should again glow both green and red (dimly). Your vehicle has a “type b” door locking system. Make sure to mark which wire is lock and unlo...

  • Page 10

    Operator programming instructions 9 trunk release and sliding van door release (+) locate the trunk release or sliding van door release wire coming from the back of the release switch. To determine if your release is tripped by a (+) positive or a (-) negative (most trunk release or van door release...

  • Page 11

    How to use your remote transmitter 10 tachless mode - on press and hold the brake pedal. Press and hold button #3 until the parking lights flash three (3) times, release, press and release button #4, the parking lights will flash once. Release the brake, the parking lights will flash three (3) times...

  • Page 12

    Starting the vehicle with the remote transmitter press and release button #1 (start). The parking lights will flash once, confirming the car starter received the signal. The car will then start and the parking lights will turn on and remain on while the vehicle is running. To shut off the engine bef...