Bullerjan O series Operating Manual - page 3
Version: 10/ 2014 - We reserve the right to make changes
2.
Firing / User manual
2.1 Firewood feed and permissible fuels
As a fuel, you should only use air-dried, natural hard wood (e. g. beechwood) in the form of logs with residual moisture of less
than 15 %.
The use of larger quantities of combustible wood does not increase the heating capacity to a major degree. Instead, the excess
engergy escapes to the chimney. In addition, this results in high hazardous emissions and in extreme cases can damage the
Bullerjan
stove O and/or individual parts.
Never use treated or plastic-coated wood, chip boards, saw dust, card board, paper, coal, coke or similar items!
Permissible fuels (max. kg/h)
Bullerjan - Type
Unit
00
01
02
Nominal heat capacity
kW
7,7
10,4
16,0
Fuel quantity
Kg/h
2,7
3,7
5,2
Fuele type
2 logs dry hard wood
Alongside
each other
Alongside
each other
Alongside
each other
Length of wood logs
25 cm
33 cm
50 cm
Adjustment primary air valvet below the door
10 mm, 42°
open
11 mm, 45°
open
16 mm, 47°
open
Adjustment secondary air above the door
½ open
1/3 open
1/3 open
Adjustment tertiary air valvet
100 % open
50 % open
50 % open
2.2
Operating Bullerjan
stoves model O
Bullerjan
hot air stoves O may only be operated with thermal safety covers
2
and with closed fire room dor. When igniting and for
the operation with nominal heat capacity please open the adjustments for primary, secondary and tertiary air as mentionned in the
schedule
under 2.1.
2.3
Combustion air adjustment
For the combustion air supply Bullerjan
®
stoves O are equipped with adjustable primary, secondary (glass washing) and tertiary
air supplies.
The glas cleaning system (secondary air supply) on top of the combustion camber door guides the secondary air along the front
glass downwards to the flame. This way, the soiling of the glass can be successful delayed. However, soiling can not be avoided
fully when burning solid fuels which naturally create soot and therefore soiling does not constitute a defect.
2.4
Heating-up procedure
Open the adjusters for the combustion air supply as mentionned in the schedule unter 2.1. Then open the fire room door and insert
the logs until just before the back wall of the stove. The logs should be placed alongside each other. Place small ignition wood or
wood chips or an ignition aid onto the logs. Ignite the igniton aid and close the stove door.
Important:
Do not use any combustible liquids like aclohol or gasoline when igniting.
Caution: HOT:
During operation, the external surfaces of the stove are very hot. No contact should be made with the stove except at the handles.
Bullerjan
stoves are coated with high-quality, heat-resitant paint which only reaches ist completely solid stage the first time the
stove is used. There will be smoke formation and odour when initially heating the stoves. Therefore, when initially heating, open
the doors and windows. Please check the viewing glass installation before initial heating. The screws for the glass holder on the
front side of the fire room door may only be or become so firmly connected that the glas can still move. The sealing cord must be
clamped by the glass all around.
2.5
Cleaning and maintenance
The parts of the Bullerjan
®
stoves O which carry flue gas and the connection pieces must be cleaned in the event of soiling, at
least once during and after the heating period. This can be done with an ash vaccuum..
Bullerjan
stoves O are working with an ash grate and an ash box. The ash grate should be cleaned of combustion residues. This
can be done with a clean out. The ash box must be emptied regularly in cold condition. To remove the ash box, please lift the ash
grate. Please do not put glowing material in the trash.
The company Bullerjan GmbH requests your understanding that our warranty claim to the Bullerjan
stoves becomes invalid if you
put too much strain on your stove by using non-permissible fuels oder by loading with fuel quantities which are excessively large.
2
Not necessary, if Bullerjan
hot air stoves O are enrased or strucurally covered. The encasing of the stoves may only be performed by
specialised licensed companies in the in-built stove and installation business.