Owner’s manual for the ground driven spreader c-dit300 c-dax ltd po box 1010, 145 harts road tiritea, palmerston north ph:06 354 6060 fax:06 355 3199 e-mail: sales@c-dax.Co.Nz www.C-dax.Co.Nz.
2 safety precautions cdit300 an important message for owners & operators of c-dax attachments/accessories be warned of the dangers of loading your atv or other vehicle in excess of its carrying capacity. It is important to understand that any loads or attachments whether fastened to or placed on a v...
3 safety precautions before attempting to install or operate the equipment, read and understand the manual thoroughly. Failure to comply with this instruction constitutes improper use and will invalidate the warranty. Throughout this manual there are highlighted text boxes containing warnings, cauti...
4 c-dax cdit300 owner’s manual (pt.No.2400-5600 issue 18, october 2015) table of contents 2 safety precautions 4 table of contents 5 introduction description specifications order information 6 warranty liability 7 operation 8 calibration magnesium oxide 9 operating the spreader adjusting the spread ...
5 introduction c-dax thanks you for your purchase of an advanced spreader from c-dax ltd. C-dax ltd is committed to providing you, the farmer, with quality applicating systems. Description the c-dax c-dit300 is a ground-driven spreader designed for application of pelleted fertilisers. It can also be...
6 warranty 1 warranty and liability use of the equipment 1.1 you must satisfy yourself as to the suitability of the equipment for your intended use(s) of the equipment. Your relationship with the retailer 1.2 where you consider you have a warranty claim (or any other claim) in relation to the equipm...
7 (e) for any loss of profit or revenue, or for any special, indirect, incidental or consequential damage, loss or injury of any kind suffered by you. 1.8 where c-dax elects to repair or replace the equipment it will use reasonable endeavours to do so as soon as practicable but will not be liable fo...
8 calibration 1. Ensure the control handle is fully back (clutch disengaged, shutter closed). 2. To calibrate your spreader, place a measured amount of product (10 kg) in the hopper. 3. Set the shutter stop lever to the position (1-9) indicated in the calibration guides below. Hole position 9 (shutt...
9 operating the spreader when the spreader has been correctly calibrated, the hopper may be filled to the required level and spreading commenced. To reduce agitator damage to product and to ensure that product is not forced past the agitator shaft when towing the spreader to the area to be treated, ...
10 maintenance the following maintenance actions are mandatory for reliable use of the spreader. Before use check the tyre pressures and charge with air as required. The correct pressure is 12 psi. (80 kpa) disengage the clutch by ensuring the control lever is fully back then turn the spinner by han...
11 parts diagram.
12 parts list item no. Qty part no description 1 1 1036-8240 agitator-spreader-cdit300/400-in-ex300/400-ss 2 1 1110-2310 ball-end-internal thread-m10-zinc plated 3 1 1140-1200 bearing-ball-pillow block-drive axle-spreaders 4 1 1140-4000 bearing-housing-pillow block-drive axle-spreaders 5 1 1280-1600...
13 45 1 3500-5600 frame-spreader-cdit300gt-gl 46 1 3800-1000 gearbox-ferroni-rv10-ratio 1 to 2.78 47 1 3865-3800 grip-handle-7/8"-pvc-black-plastic 48 1 3990-3900 guide-handle-cdit300/400gt-zp 49 1 4050-1500 handle-cdit300/400gt-zp 50 1 4050-4250 handle-indicator-cdit400gt-zp 51 1 5050-1600 linkage-...
