Summary of CAT-1X
Page 2
2 / 20 content index 1-introduction: .............................................................................................................................................. 3 1.1- instruction of safety: .............................................................................................
Page 3: 1-Introduction:
3 / 20 1-introduction: cat-1x is a gsm/gprs/gps alarm tracking box for multi applications. This small unit is equipped with quad bands gsm/gprs module, hi-sensitivity gps receiver and 3d accelerometer. It’s also can be connected with optional wireless/wired accessories like pir senor, doppler moveme...
Page 4
4 / 20 - gsm: • antenna: external • modem: quectel m35 /quad bands:850/900/1800/1900mhz - radio frequency: • working frequency: 433mhz. • code: 1527/2240 study • working voltage: 12v ( 27a 12v dry battery) • control distance: 20-50m - environmental: • working temp.: -20℃ ~ +75℃ • humidity: 20-95% 1....
Page 5: 2-Knowlege Before Usage:
5 / 20 note: please kindly noted that optional accessories are not available in the standard package. But they are available for purchase separately from manufacturer. 2-knowlege before usage: 2.1- how it works? The cat-1x mainframe works as a host box with multi input/outputs. The mainframe will pr...
Page 6
6 / 20 • speed over limit: off • geo fence: off • data transmit mode: sms default when gprs parameter is not configured • siren: on • automatic immobilizer in armed status: disabled • automatic power supply switch from external to internal when external power low: enabled • external power low voltag...
Page 7
7 / 20 arm: buzzer sound once, or direction light flash once disarm: buzzer sound twice or direction light flash twice. Mute key: in siren sounding, press this button to stop the sounding. In panic, activate siren to sound. Or in parking lot, press this button for car finding. 2.4.2 transmitter and ...
Page 8
8 / 20 2.5.2 configure by pc tool “ configurator”: 1. Connect cat-1x with pc via usb cable: 2.Install cp2102 usb-serial driver:.
Page 9
9 / 20 3. Run cat-1x configurator.Exe and get into following interface: 2.6 i/o introduction and definition 1. Main i/o ports introduction:.
Page 10
10 / 20 2. I/o pin slot definition l1 18pin port pin slot definition: l1 molex 18pin connector wire description pin no. Wire color function/specification description power 9 red/white power positive pole, 9-60v dc 18 black/white ground digital output 6 purple/white over speed buzzer(=0v,effect) 8 ye...
Page 11: Functions and Operation:
11 / 20 functions and operation: 3.1 arm/disarm arm/disarm: arm: in armed status after arm operation, any illegal events happened in i/o ports or wireless sensor will trigger siren sound and sms alerts. Disarm: opposite to arm, user is free to do any operation but no alarm alert will be triggered. R...
Page 12
12 / 20 voltage external battery charge alert sms once sms once sms once yes daily travel mileage sms report sms once call-in direct for voice listen-in yes yes yes wireless sensor trigger alert(smoke, pir, gas, magnetic door sensor) sms once sms once sms once sms once 20seconds sound yes short-call...
Page 13
13 / 20 3.5 shock alert ,crash accident alert and crash accident data logger cat-1x box is with built-in 3d acceleration sensor (g sensor) on board. The device use this g sensor created three functions. 1. Shock alarm cat+-1x will detect all x,y,z acceleration always, any changes in all x,y,z axis w...
Page 14
14 / 20 any axils exceed the configured g value, it will trigger the accident alert 3. Crash accident data logger for before/after 15seconds in accident time cat-1x will record recent 3times accident g varies truth in memory. And allow user to load out via usb connection through the configurator pro...
Page 15
15 / 20 3.6 voice listen-in call center number d and sms center service no. G call cat-1x, the system will put through to voice listen-in mode directly. Cat-1x also provide other two methods to start voice listen-in operation: 1. By sms command with correct password to cat-1x box to get re-call back...
Page 16
16 / 20 *1234*where# *1234*find# *1234*gps# 2. Track by 7-24tracking portal (has to configure ip/port/apn and get tracking account name and password) 3.12.2 speed limit manage 1. Speed limit configuration by sending sms command *1234*spd080# configure as speed limit as 80km/h. 2.Speed over alert: af...
Page 17
17 / 20 factory. Only can be used after activate by sms command>>>). Speed over sms alert for a/b/c/g number with contents: “over speed alert;2011-12-08 12:32:13,v,60km/h,heading:60,lac:2638,cid:0ecf; http://maps.Google.Com/maps?Hl=en&q=22.537222,114.020948 “ and cat-1x will generate this alert to 7...
Page 18
18 / 20 by configurator program or sms commands, user can configure one call center voice service number d in cat-1x. After the short call button was pressed, the cat-1x will start to call this d number and connect to talk with call center support people. 3.14 remote door lock/unlock cat-1x get two ...
Page 19
19 / 20 defense area name alarm type code define sensor numbers supported h 1= fire alarm 2= gas leakage alarm 3= intrusion alarm 4= booth open alarm 5= glass broken alarm all areas supported 1/2/3/4/5 alarm type, and each type can program 5sensors maxium in one area. Example h1 can program 5 same s...
Page 20: 4. Problem Shooting
20 / 20 note: please configure cat-1x time zone to be your local time before you setup this. 3.20 ota firmware cat-1x supports firmware upgrading via gprs. To use this function, you have to enable gprs connection on the cat-1x command. Firmware upgrading sms command is: *password*upgrade:xxx.Xxx.Xxx...