1. DL manuals
  2. CAB
  3. Water Filtration Systems
  4. MAESTRO 4S
  5. Operator's Manual

CAB MAESTRO 4S Operator's Manual

Other manuals for MAESTRO 4S: Service Manual
Manual is about: PCB Separator

Summary of MAESTRO 4S

  • Page 1

    Operator's manual maestro 4s pcb separator.

  • Page 2

    2 description type pcb separator maestro 4s edition: 10/2017 part no.: 9009613 copyright this documentation as well as translation hereof are property of cab produkttechnik gmbh & co. Kg. The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentions ...

  • Page 3

    3 table of contents 1 introduction ............................................................................................................................................ 4 1.1 instructions ............................................................................................................

  • Page 4

    4 1.1 instructions important information and instructions in this documentation are designated as follows: danger! Draws your attention to an exceptionally grave, impending danger to your health or life. ! Warning! Indicates a hazardous situation that could lead to injuries or material damage. ! Att...

  • Page 5

    5 • work going beyond this may only be performed by trained personnel or service technicians. • unauthorized interference with electronic modules or their software can cause malfunctions. • other unauthorized work on or modifications to the device can also endanger operational safety. • always have ...

  • Page 6

    6 2 technical data technical data 4s/450 4s/600 separation type component side: soldering side: circular blade linear blade operation motorized and optimized separation speedt 300/500 mm/sec. Switchable material fr4, aluminium height of components component side/soldering side up to 34 mm cutting le...

  • Page 7

    7 3 contents of delivery 5 6 4 2 1 3 1 maestro 4s/300 (600) 2 power cable 3 dial gauge assembly 4 food switch 5 hexagonal wrench din911 2mm 6 hexagonal wrench din911 5mm 7 documentation fig.2 contents of delivery gelb pantone 123c , grün ral 6018 , blau pantone 7461 , grau pantone 422c , beschriftun...

  • Page 8

    8 5 installation 5.1 electrical links ! Attention! The device and printing materials will be damaged by moisture and wetness.  set up the device only in dry locations protected from splash water. I notice! Clean the blade with a soft cloth before you start the machine at first time! 4 5 7 3 2 1 6 f...

  • Page 9

    9 6 switch on and programming i notice! You can separate pcb panel with multiple cuts very softly. It means, more cuts are gentle for material and elements on the pcb board. 6.1 switch on and synchronize the blade 1. Switch on the device by power switch (1). Led not ready is blinking. I notice! Are ...

  • Page 10

    10 6.3 recommendation for cutting - depend of notch thickness and number of cuts notch thickness i notice! The cutting is more gentle for the pcb's with a higher number of cuts. The deepness of the last cut must be so that the pcb's are easily to separate. The values are recommendation and it's poss...

  • Page 11

    11 6.4 changing the program switch between program 1 - 9  press button program and hold it over 3 seconds. The display of the selected program is blinking.  select the program by pressing the program button.  if the button program not used for 3 seconds, the program display will end the blinking ...

  • Page 12

    12 8 operation if the device switched of an d on it' will start in the last program before switched off. Switch on the device by the power-switch (1). Led not ready blinking. 1 fig.8 power switch 1. Press button home. 2. Press the foot-switch and hold it. - device will run to the start position or f...

  • Page 13

    13 9 maintenance 9.1 changing the upper blade in case of wasting, damage or material cahange it's necessary to change the upper blade. Risk of hand injury!  wear protective gloves while changing the blade. Danger! Risk of cutting damage by rotating blade! Disconnect device before you start service ...

  • Page 14

    14 9.2 adjustment of the upper blade stopper i notice! The lower stop of the upper blade adjustment is already adjusted by delivery.  after a long operation time, while working at strongly varying temperatures or else after replacing a blade, it is recommended to re-adjust the lower stop. 3 5 6 1 2...

  • Page 15

    15 9 maintenance 9.3 upper guide adjustment 2 2 3 1 4 a fig.12 upper guide adjustment 1. Using a pre-scored pcb, check the clearance „a“ between the upper guides (1,3) and the lower blade (4). The clearance should be set so that the edge of the upper guide is located correctly into the pre-scored gr...

  • Page 16

    16 9.5 changing the linear blade ! Warning! Risk of cutting injury in handling of the linear blade. Risk of hand injury!  wear protective gloves while changing the blade. X z y x z y 3 4 2 1 fig.14 changing the linear blade (front view - inclined) fig.15 changing the linear blade (bottom view - inc...

  • Page 17

    17 9.6 adjusting the linear blade ! Warning! Risk of cutting injury in handling of the linear blade. To ensure a constant cutting quality and to prevent damaging of the blades must adjust the linear blade so that the distance between upper blade and linear blade is constant of the full cutting lengt...

  • Page 18

    18 9.7 check the blade alignment i notice! When the machine is put into operation for the first time, or following a move of equipment or a change of blades, it is advantageous to re-check the alignment of the blades in relationship to one another. For this purpose a dial gauge assembly (part no. 89...

  • Page 19

    19  remove the existing roller blade shift the added fitted washer (cab part no.: 5903026.001) on the axle. Attach the roller blade fr4 (cab part no.: 8930509.001) like the descripion of the operator‘s manual..  check the offset. Setting of the lower stopper 2 3 1 fig.20 setting knob on the carria...

  • Page 20

    20 cab produkttechnik gmbh & co kg wilhelm-schickard-str. 14 d-76131 karlsruhe deutschland eu declaration of conformity we declare herewith that the following device as a result of design, construction and the version put in circulation complies with the relevant fundamental regulations of the eu ru...