- DL manuals
- Cabletron Systems
- Software
- CSMIM-T1
- Quick Start Manual
Cabletron Systems CSMIM-T1 Quick Start Manual
Summary of CSMIM-T1
Page 1
Title page csmim/micro-cs quick start for windows nt.
Page 3: Notice
Remote annex quick start for windows 1 notice cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. T...
Page 4: Exclusion Of Warranty
Remote annex quick start for windows 2 exclusion of warranty and disclaimer of liability 1. Exclusion of warranty. Except as may be specifically provided by cabletron in writing, cabletron makes no warranty, expressed or implied, concerning the program (including its documentation and media). Cablet...
Page 5: Preface
Remote annex quick start for windows 1 preface this guide is designed for quick installation of a remote annex in a windows nt network environment and configuration of the annex using quick2config annex. The instructions apply to all remote annex models including the remote annex 6300. The procedure...
Page 6
Preface 2 remote annex quick start for windows formats and usage throughout this document, the following terms may be used to refer to cabletron systems products or documentation. Table 1 summarizes the alternate terminology and the cabletron product, device, or document that it refers to. Table 1: ...
Page 7
Preface remote annex quick start for windows 3 related documents each remote annex hardware platform ships with the appropriate hardware guide. The remaining documentation is included with the software. [ ] in command dialogue, square brackets indicate default values. Pressing selects this value. Sq...
Page 8
Preface 4 remote annex quick start for windows getting help if you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact cabletron systems technical support: before calling cabletron systems technical support, have the ...
Page 9: Remote Annex Quick Start
Remote annex quick start for windows 1 remote annex quick start for windows nt before installing the software prerequisites to install remote annex server tools for windows nt, you need: ❑ microsoft windows nt server 3.51 or 4.0 configured to support the tcp/ip protocol ❑ administrative privileges o...
Page 10: Server Software
2 remote annex quick start for windows the grant to box displays the names of all groups currently allowed to log on locally. 3 edit the list using and . ❑ to add groups or individual users, click on and select individual or group names from the add users and groups window. ❑ to delete users or grou...
Page 11
Remote annex quick start for windows 3 ❑ the na and quick2config annex software can be loaded on windows nt workstations (3.51 or 4.0) and on windows 95 platforms. ❑ quick2config annex can be installed on windows for workgroups 3.11 and windows 3.1 systems. To install quick2config annex on a windows...
Page 12
4 remote annex quick start for windows the remote annex 2000 uses port 1 as its console port. The remote annex 539x uses the service port on the 5000 chassis as the console port. 3 set the terminal to 9600 bps, 8 bits, 1 stop bit, no parity and no flow control. 4 for the remote annex 2000 or remote ...
Page 13: Using Quick2Config Annex
Remote annex quick start for windows 5 select type of ip packet encapsulation (ieee802/ethernet) []:: type of ip packet encapsulation: monitor:: load broadcast y/n [y]:: all annexes 2 if you have purchased a lat key, enter the software key provided. Monitor:: lat enter lat key: []:: booting the remo...
Page 14: Using The Na Utility
6 remote annex quick start for windows 1 invoke na, configure the remote annex to accept and process snmp command sets, and exit na. % na command: annex 129.9.200.62 command: set annex allow_snmp_sets y command: boot command: quit 2 click on the quick2config icon to open the application. 3 choose fi...
Page 15
Remote annex quick start for windows 7 % na command: annex 192.9.200.62 command: port 6 command: set port speed 115200 command: set port control_lines modem_control command: set port input_flow_control start/stop command: set port output_flow_control start/stop command: set port type dial_in inbound...
Page 16: Configuring Security
8 remote annex quick start for windows dataproducts interface set the printer type using na and send data to the printer using aprint: % na command: annex 192.9.200.62 command: printer 2 command: set printer type dataproducts command: reset printer command: quit % aprint -a 192.9.200.62 -p2 [filenam...