- DL manuals
- Cabletron Systems
- Switch
- DLM6C-AA
- Overview And Setup Manual
Cabletron Systems DLM6C-AA Overview And Setup Manual
Summary of DLM6C-AA
Page 1
Digital multiswitch 700 dlm6c-aa overview and setup guide.
Page 3
Digital multiswitch 700 dlm6c-aa overview and setup guide part number: 9032610 september1998 this guide describes how to install and configure the digital multiswitch 700 dlm6c-aa chassis. Revision/update information: this is a new document..
Page 4
Cabletron systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult cabletron systems to determine whether any such changes have been made. The hardware, firmware, or software described i...
Page 5
Fcc notice — class a computing device: this equipment generates, uses, and may emit radio frequency energy. The equipment has been type tested and found to comply with the limits for a class a digital device pursuant to part 15 of fcc rules, which are designed to provide reasonable protection agains...
Page 6
Cabletron systems, inc. Program license agreement important: before utilizing this product, carefully read this license agreement. This document is an agreement between you, the end user, and cabletron systems, inc. (“cabletron”) that sets forth your rights and obligations with respect to the cablet...
Page 7
Declaration of conformity application of council directive(s): 89/336/eec 73/23/eec manufacturer’s name: cabletron systems, inc. Manufacturer’s address: 35 industrial way po box 5005 rochester, nh 03867 european representative name: mr. J. Solari european representative address: cabletron systems li...
Page 11: Contents
Dlm6c-aa overview and setup guide ix contents preface using this guide ............................................................................Xi structure of this guide...................................................................Xi document conventions .......................................
Page 12
Contents x dlm6c-aa overview and setup guide 3.3 powering up a dlm6c-aa with an ac power supply...............3-11 3.4 powering up a dlm6c-aa with a dc power supply.................3-11 3.4.1 connecting an ha205-md to 48/60 vdc source...........3-13 3.5 removing and reinstalling the fan tray ..........
Page 13: Preface
Dlm6c-aa overview and setup guide xi preface welcome to the digital multiswitch 700 dlm6c-aa overview and setup guide . This guide explains how to set up and configure the dlm6c-aa chassis. Using this guide read through this guide completely to familiarize yourself with its contents and to gain an u...
Page 14: Document Conventions
Xii dlm6c-aa overview and setup guide document conventions throughout this guide, the following symbols are used to call attention to important information. Using the digital multiswitch 700 manual set other manuals have been developed for the interface modules that can be installed in the dlm6c-aa ...
Page 15: Correspondence
Dlm6c-aa overview and setup guide xiii correspondence documentation comments if you have comments or suggestions about this manual, send them to digital network products: world wide web to locate product-specific information, refer to the digital network products home page on the world wide web at t...
Page 17: Safety
Dlm6c-aa overview and setup guide xv safety overview any warning or caution that appears in this manual is defined as follows: warning warns against an action that could result in equipment damage, personal injury, or death. Vorsicht warnt den benutzer vor aktionen, die das gerät beschädigen, person...
Page 18: Safety Requirements
Safety xvi dlm6c-aa overview and setup guide safety requirements the warnings or cautions that must be observed for the hardware described in this manual are listed below in english, german, french, and spanish. Warning only qualified personnel should install or service this unit. Vorsicht diese ein...
Page 19
Safety requirements dlm6c-aa overview and setup guide xvii vorsicht wenn der dlm6c-aa auf einem regal plaziert werden soll, muß das regal eine last von ca. 34 kilogramm (75 pfund) unterstützen können. Wenn der dlm6c-aa dagegen in einem einschubgehäuse installiert werden soll, muß der einschub die ei...
Page 20
Safety xviii dlm6c-aa overview and setup guide warning to reduce the risk of electric shock or energy hazards: ensure the branch circuit overcurrent protection is rated at a minimum of 25 a. Use the 10 awg solid copper conductors only. Ensure that a readily accessible disconnect device that is suita...
Page 21
Safety requirements dlm6c-aa overview and setup guide xix aviso para reducir el riesgo de descarga eléctrica o peligros relacionados con la energía: asegúrese de que la protección contra sobretensión del circuito de derivación sea como mínimo de 25 a. Use únicamente conductores de cobre sólido de ca...
Page 22
Safety xx dlm6c-aa overview and setup guide caution to prevent damaging the backplane connectors in the following step, take care that the module slides in straight and properly engages the backplane connectors. Achtung um die anschlüsse an der rückseite bei diesem schritt nicht zu beschädigen, stel...
Page 23
Safety requirements dlm6c-aa overview and setup guide xxi caution the dlm6c-aa and the host module or hub are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damage to this equipment. Achtung der...
Page 25: Chapter 1
Dlm6c-aa overview and setup guide 1-1 chapter 1 introduction 1.1 overview the digital dlm6c-aa chassis design provides five 2.4-inch slots that can contain a variety of interface modules. The chassis supports redundant power supplies, lanview diagnostic leds, and is 19-inch rack mountable. All chass...
Page 26: 1.2
Chapter 1: introduction 1-2 dlm6c-aa overview and setup guide 1.2 features redundant power supply modules the dlm6c-aa supports two power supply modules that reside in the slots labeled ps1 and ps2. The dlm6c-aa ac power supply module (ha205-aa) supports an ac input connector that allows the power s...
Page 27
Features dlm6c-aa overview and setup guide 1-3 refer to the module specific user’s guide for instructions on how to access power supply status information using local management. Auto-ranging power supplies the dlm6c-aa power supply modules automatically adjust to the input voltage and frequency. No...
Page 29: Chapter 2
Dlm6c-aa overview and setup guide 2-1 chapter 2 installation requirements and specifications this chapter describes the following: • site guidelines that must be met before installing a dlm6c-aa into a rack or cabinet • dlm6c-aa configuration guidelines • operating specifications for the dlm6c-aa en...
Page 30: 2.2
Chapter 2: installation requirements and specifications 2-2 dlm6c-aa overview and setup guide • the ha205-md dc power supply requires a 10 american wire gauge (awg) solid copper conducter with #6 ring terminals. 2.2 configuration guidelines the dlm6c-aa has 5 slots that accept interface modules. The...
Page 31: 2.3.1
Operating specifications dlm6c-aa overview and setup guide 2-3 2.3.1 physical specifications the physical specifications for the dlm6c-aa chassis, h3105-aa fan tray, and the ha205-md and ha205-aa power supply modules are as follows: dlm6c-aa chassis ha205-md power supply ha205-aa power supply h3105-...
Page 32: 2.3.2
Chapter 2: installation requirements and specifications 2-4 dlm6c-aa overview and setup guide 2.3.2 power supply requirements the power supply requirements for the dlm6c-aa power supply modules are as follows: ha205-md dc power supply ha205-aa ac power supply 2.4 leds the following sections describe...
Page 33
Operating specifications dlm6c-aa overview and setup guide 2-5 figure 2-1 power supply leds table 2-1 power supply led states and their definitions led name color status pwr (power) green all outputs and input of the power supply are within regulation. Red any output or input of the specific power s...
Page 34: 2.4.2
Chapter 2: installation requirements and specifications 2-6 dlm6c-aa overview and setup guide fan tray led lkg-10798-98f tm h3105-aa 2.4.2 fan tray led the following table describes the different states of the fan tray led and their definitions. Refer to figure 2-2 for the location of the fan tray l...
Page 35: Chapter 3
Dlm6c-aa overview and setup guide 3-1 chapter 3 dlm6c-aa setup this chapter contains instructions on setting up the digital dlm6c-aa chassis. A phillips screwdriver is needed to install the unit in a 19-inch equipment rack, to install the cable management bar, to secure the power supply module, and ...
Page 36: 3.2
Chapter 3: dlm6c-aa setup 3-2 dlm6c-aa overview and setup guide 6. Remove the console cable kit and set aside. This kit will be needed to set up the modules for the dlm6c-aa through local management. 3.2 setting up the dlm6c-aa the following sections describe the procedures that must be followed to ...
Page 37: 3.2.2
Setting up the dlm6c-aa dlm6c-aa overview and setup guide 3-3 3.2.2 installing the cable management bar to install the cable management bar, proceed as follows: 1. Remove the cable management bar from the shipping box. Ensure that there are four screws inside the bag with the cable management bar. 2...
Page 38: 3.2.3
Chapter 3: dlm6c-aa setup 3-4 dlm6c-aa overview and setup guide 3.2.3 rack mounting the dlm6c-aa the dlm6c-aa can be mounted in a standard 19-inch equipment rack. Two people may be required to lift the chassis into place. The chassis is secured with ten screws, five on each side. Using the screws pr...
Page 39: 3.2.4
Setting up the dlm6c-aa dlm6c-aa overview and setup guide 3-5 3.2.4 attaching the esd wrist strap the esd wrist strap must be attached before handling the dlm6c-aa power supplies, fan tray, or modules. In addition, observe all precautions when handling these modules to prevent damage from esd. Place...
Page 40: 3.2.5
Chapter 3: dlm6c-aa setup 3-6 dlm6c-aa overview and setup guide 3.2.5 installing a power supply module you must install at least one power supply in the dlm6c-aa chassis. One power supply provides sufficient power for most module configurations but a second power supply can be installed to provide a...
Page 41
Setting up the dlm6c-aa dlm6c-aa overview and setup guide 3-7 4. Slide the power supply module into the slot labeled ps1 as follows: a. Hold the module by placing one hand on the handle located on the module front panel and using the other hand to support the body of the module. B. With the led at t...
Page 42
Chapter 3: dlm6c-aa setup 3-8 dlm6c-aa overview and setup guide figure 3-4 installing the power supply module after installation of the power supply modules is completed, the dlm6c-aa is ready to be powered up; however, digital recommends that installation of all modules for the dlm6c-aa be complete...
Page 43: 3.2.6
Setting up the dlm6c-aa dlm6c-aa overview and setup guide 3-9 3.2.6 installing dlm6c-aa interface modules the dlm6c-aa interface modules can be installed in any of the 5 slots that are available. To install a module, proceed as follows: 1. Remove the blank panel covering the slot in which the interf...
Page 44
Chapter 3: dlm6c-aa setup 3-10 dlm6c-aa overview and setup guide figure 3-5 installing a module 1 2 3 4 5 ps1 ps2 plastic locking tab slot number lkg-10803-98f circuit card card guides metal back-panel plastic locking tab backplane connector multiswitch 700 tm tm dlm6c-aa tm ha205-aa tm ha205-aa h31...
Page 45: 3.3
Powering up a dlm6c-aa with an ac power supply dlm6c-aa overview and setup guide 3-11 3.3 powering up a dlm6c-aa with an ac power supply to power up a dlm6c-aa with the ha205-aa ac power supply module, proceed as follows: 1. Plug one end of the power cord (supplied with the power supply) into the ac...
Page 46
Chapter 3: dlm6c-aa setup 3-12 dlm6c-aa overview and setup guide figure 3-6 power supply dc on/off switch and dc input power strip only qualified personnel should perform these installation procedures. To reduce the risk of electric shock or energy hazards: • connect to a reliably grounded 48/60 vdc...
Page 47: 3.4.1
Powering up a dlm6c-aa with a dc power supply dlm6c-aa overview and setup guide 3-13 dc power supply requirement for each supply each dc power supply input requires either a 48 vdc or 60 vdc power source, rated at a minimum of 17 amps. Installation requirement each dc power supply input requires eit...
Page 48: 3.5
Chapter 3: dlm6c-aa setup 3-14 dlm6c-aa overview and setup guide 3. Repeat steps 1 and 2, if applicable, to connect a 48/60 vdc power source to a second ha205-md installed in the chassis. 4. Restore power to the 48/60 vdc power sources. 5. Press the on/off power switch of each power switch to on. If...
Page 49: 3.5.2
Removing and reinstalling the fan tray dlm6c-aa overview and setup guide 3-15 figure 3-8 removing the fan tray 3.5.2 reinstalling the fan tray to reinstall the fan tray, refer to figure 3-9 and proceed as follows: 1. Locate the esd wrist strap shipped with the dlm6c-aa. Attach the esd wrist strap to...
Page 50
Chapter 3: dlm6c-aa setup 3-16 dlm6c-aa overview and setup guide 3. Line up the rails on each side of the fan tray with the slot guides on the chassis. 4. Slide the fan tray forward until the faceplate of the tray is flush with the face of the dlm6c-aa. If there is any strong resistance, remove the ...
Page 51
Removing and reinstalling the fan tray dlm6c-aa overview and setup guide 3-17 figure 3-9 reinstalling the fan tray slot guides slotted screws (2) 1 2 3 4 5 ps1 ps2 lkg-10807-98f multiswitch 700 tm tm dlm6c-aa h3105-aa.
Page 54
9032610 printed in u.S.A..