Cadac Maestro 3B User Instructions - page 14
24
25
17. ASSEMBly PROCEDURE
Patio 4B Select / 98521S, Patio 3B Select / 98520S,
Figure 1
•
Place the BBQ unit, lying on its back, on a flat, level surface.
•
Align the spacer with the corresponding holes on the leg.
•
Fasten leg & spacer to BBQ body using M6x70mm screws supplied.
•
Do not tighten screws.
•
Repeat the above for the remaining legs.
Figure 2
•
Assemble the magnet to the top face of the bottom panel using the M3x12 screws and nuts supplied.
•
Fit the bottom panel to the frame by aligning the holes in the bottom panel with the holes on the legs, secure in position using
the M6x12mm screws supplied.
•
Assemble the remaining magnet to the bracket situated underneath the top panel.
•
Fit the top panel to the frame by aligning the holes in the top panel with the holes in the legs. Only fit the front 2 screws. leave
the back loose so that the top panel can swivel up and down.
Figure 3
•
Fit the small castor wheels to the frame aligning the threaded stud on the wheel with the hole underneath the leg. Screw the
wheel into the leg. Fasten securely.
•
Push the axle through the wheel and align with the corresponding hole on the leg. Fasten the wheel to the frame using the M10
nut supplied. Fasten securely.
•
Fit the hub cap by clipping it onto the wheel.
Figure 4
4.1 Turn the unit upright and place it on a flat surface.
Fit the back panel between the top and bottom panels by aligning the tags on the back panel with the cut-outs on the bottom
panel.
4.2 lift the back end of the top panel up and align the tags on the back panel with the cut-outs on the top panel.
4.3 lower the top panel onto the back panel and secure the top panel in place using the M6x12 screws supplied (see a, b & c
above).
4.4 Fit the cylinder bracket to the left side panel using the M6x12 screws and nuts supplied.
Fit the side panels by aligning the holes in the side panels with the holes in the top & bottom plate. Secure in position using
the M6x12 screws & nuts supplied.
Figure 5
5.1 Fit the door handles to the doors using the screw supplied.
5.2 Fit the M6 stud to the bottom of the door using the M6 nut & washer supplied.
5.3 Fit the top rotating axle to the door using the M3x12 screws and m3 nuts supplied.
5.4 Fit the door to the frame by first locating the 6mm stud in the corresponding hole in the bottom plate.
5.5 Align the top rotating axle with the corresponding hole in the top panel. Push in the rotating axle and slide the door into place.
The axle will clip into the corresponding hole on the top panel.
Figure 6
•
Fit side tray to the frame using the M6x12mm screws supplied.
•
Fasten all screws securely.
•
Repeat the process for both trays
Figure 7
•
Fit the drip tray by sliding it into the BBQ unit from the rear.
•
Fit the oil cup to the drip tray by sliding it into the bracket situated underneath the drip tray.
Figure 8
•
Place a flame tamer over each burner.
•
Fit the grill plate / griddle plate by placing it inside the BBQ body.
•
Fit the warming rack to the locators situated inside the BBQ body.
Figure 1
Figure 2
Figure 3
Figure 4.1
Figure
4.2
Figure
4.3
Figure
4.4
Figure 7
Figure 8
Figure 6
Figure 5.1
Figure 5.2
Figure 5.3
Figure 5.4
Figure 5.5
a
b
c
Figure 4 (cont.)