Crcode-202 mechanical lock instruction and programming manual before installing: 1. Please read the instructions carefully to prevent missing important steps. *note: improper installations may result in damage to the lock which will void the factory warranty. 2. Please keep this instruction manual f...
Table of contents introduction parts checklist before installation door handing installation procedure mark and drill door change door handing cut spindle according to door thickness alignment post location crcode-202 exploded view latch and spindle installation adapter instructions outside lock ins...
Parts pcs remarks 1 outside lock 1 2 inside lock 1 3 2 3 / 4 edfnvhw¿uhodwfkerow 1 70mm 2 3 / 4 ” backset 4 spindle 1 5 spindle adapter 1 6 8-32 x 3 / 8 ” screws 4 backplate f ixing bolts 7 10-32 x 1 3 / 16 ” screws 4 iurqwsodwh¿[lqjerowvirugrruwklfnqhvv 35mm - 44mm (1 3 / 8 ” - 1 3 / 4 ”) 10-32 x 1...
Checklist before installation: door handing drill the holes use the right parts install adjust reset code installation procedures change the lever handle and latch direction accordingly *the example in this manual is a right hand door right hand left hand right hand reverse left hand reverse 1. Door...
Mark and drill door 1. Attach template onto door and verify backset and latchbolt center, before marking and drilling holes on the door. 2. Drill holes on the door. *drilling a hole from both sides is recommended to avoid splintering wood doors. 2.1 drill 2 1 / 8 ” diameter thru holes. 2.2 cut notch...
Make sure this is set horizontally to change handing outside lock (lever shipped right handed) 1. Insert key and turn 90° clockwise. 2. Insert lever catch on the bottom of the lever. 3. Pull lever off. 4. Fit lever to the desired opposite left hand of the door. 5. Turn key 90° clockwise and push lev...
Cut spindle according to door thickness 1. Spindle supplied with breakable srlqwviruvshfl¿fgrruwklfnqhvv requirements. 2. Break off one or two points from the spindle, according to the door thickness measurement. Alignment post location a d c b 1. As tubular latchbolts only have one bolt hole, faste...
Exploded view of crcode-202 latch and spindle installation ,qvhuwwkh¿uhfxslqwrwkhkroh,iqrwxvlqjd¿uh cup, skip this step) 2. Insert the latch into the side hole. 3. Fix the latch with two 8-32x34” wood screws. 4. Fit the spindle into the latch according to the handing of the door (refer to “adapter i...
&khfnwkdwwkhodwfklvfruuhfwo\¿wwhgdvvkrzqrq right image. Outside lock installation 1. Place outside lock on door. 2. Align hub onto the spindle and 4 screw posts through prep doors. 3. Align the mounting plate of the inside lock and fasten with 4 screws. 8 6605 flotilla st., commerce, ca 90040 tel (3...
Inside lock installation install strike plate check & adjust 1. Place inside lock onto the door. 3. Fasten with 4 screws. 2. Push lever onto the hub until it clicks. 1. Align strike plate with rabbet. 2. Fasten strike plate with 2 screws. 1. Enter factory set code and make sure that the latchbolt re...
10 6605 flotilla st., commerce, ca 90040 tel (323) 888-6601 fax (323) 888-6699 www.Cal-royal.Com to change access code 1. Press current access code. 2. Turn lever 70° and hold. 3. Press the y button. 5hohdvhwkhohyhu¿uvwdqgwkhqwkh (y button will stay pressed until code is changed) 5. Push the code ch...
11 6605 flotilla st., commerce, ca 90040 tel (323) 888-6601 fax (323) 888-6699 www.Cal-royal.Com to change access code 8. Press “c” and the new access code. 9. Turn the lever. The y button will pop back up once the code is changed. *before pressing the access code, make sure to press ³&´exwwrq&ohdu¿...
12 6605 flotilla st., commerce, ca 90040 tel (323) 888-6601 fax (323) 888-6699 www.Cal-royal.Com.
6605 flotilla st., commerce, ca 90040 tel. (323) 888-6601 fax. (323) 888-6699 website: www.Cal-royal.Com email: sales@cal-royal.Com.
