Summary of HANDI-LIFT 7
Page 1
Installation manual for handi-lift 7.
Page 2
Handi-lift 7 2010 page 1 version 1.0 table of contents 1 introduction 2 1.1 check the parts and drawing: 2 1.2 electrical installation: 2 2 forces on the building 3 3 install the rails 4 3.1 column installation: 4 3.2 upper and lower rail installation: 4 4 installing the lift unit 8 4.1 place the li...
Page 3
Handi-lift 7 2010 page 2 version 1.0 1introduction 1.1check the parts and drawing: before you start installing please read this installation manual. Check the received parts for transport damage. Next, study carefully the installation drawing that comes with the lift to ensure that all angels and di...
Page 4
Handi-lift 7 2010 page 3 version 1.0 wall mounted rail 1. The top (main) rail fixings are m10x160mm studs & 'rawl' r-kf2 kemfast resin into the wall. 2. The lower rail fixings must be made using no.12x75mm csk screws & rawlplugs. There are 250mm between the fixing bolts in the rail. The bending stre...
Page 5
Handi-lift 7 2010 page 4 version 1.0 3install the rails 3.1column installation: if the handi-lift is installed on columns you have to start with them. Place the columns after the measurements on the drawing they are usually numbered with the lowest number at the foot of the stairs. When installing t...
Page 6
Handi-lift 7 2010 page 5 version 1.0 fig. 2 mark measurement b mark measurement c from the first and last raise parallel with the staircase. Note! Measurement c is the upper edge of the inner profile. Make a line through mark a-a and d. And make a line through mark c-c. Fig. 1 fig. 2 place the upper...
Page 7
Handi-lift 7 2010 page 6 version 1.0 note! For wall installation we recommend that you use m10 glue bolts for the upper rail when mounted on a wall with the threaded rod minimum 90mm into the wall. And for the lower rail, we minimum recommend ø10 raw plugs with m8x70mm screws. For installation on co...
Page 8
Handi-lift 7 2010 page 7 version 1.0 fig. 10 install and tighten the support rail for the lower rail fig. 11 install the aluminium rail on the support rail using the m5x10mm countersunk screws. Fig. 12 after letting the glue set for a half-hour in 20 o c you can tighten the nuts on the glue bolts. O...
Page 9
Handi-lift 7 2010 page 8 version 1.0 4installing the lift unit 4.1place the lift unit on the rail: hand wind platform in it’s down position and remove the front cover from the lift unit. Install the loose carrying arms.
Page 10
Handi-lift 7 2010 page 9 version 1.0 fig. 13 please use tape to protect the rail. Optional: to make the lift easier to handle you can disassemble the platform, if necessary. We recommend you install the lift with the platform assembled. Before inserting the lift to the rail make sure that the upper ...
Page 11
Handi-lift 7 2010 page 10 version 1.0 fig. 16 fig. 17 fig. 18 plug the remote lead into the control board. Drive the lift to the lowest part of the rail and commence the programming operation. Dismount the carrying arms and install the barrier arms to the unit. And lightly lubricate the drive chain ...
Page 12
Handi-lift 7 2010 page 11 version 1.0 4.2connect the electrical: wire all required charging points to the upper rail section ensuring that all cables are free from any damage. Charging points are placed at all the lifts stops and wires are connected. Wire back to charging unit and electrical test op...
Page 13
Handi-lift 7 2010 page 12 version 1.0 description of installation location: ________________________________________________________________ rated load: ____________ kg stairlift serial no: ______________________ rated speed: ___________ m/s type and year of manufacturer: _________________________ m...
Page 14
Handi-lift 7 2010 page 13 version 1.0 h. Verify that the polarity of the mains supply connection is correct i. Test to verify the functional operation of the overspeed detection device and safety gear j. Verify that the mechanism for emergency/manual operates correctly k. The alarm device when activ...