Cambridge Audio CRX200 Owner's Manual - page 16
16
DTS-HD speaker re-map
When playing back a DTS-HD track the CXR can electronically reposition
your speakers to match the setup used in the original recording studio. This
is done automatically in most cases, but for 7.1 setups you will need to
choose either option 1 or 5 – whichever most closely resembles your actual
speaker layout.
*VUÄN\YH[PVU¶JOHUULS!3*93-,3Z9Z3ZY9ZY
Center
Right (30°)
Left (30°)
Left Surround (110°)
Left Surround Rear
(150°)
Right Surround Rear
(150°)
Right Surround
(110°)
LFE
*VUÄN\YH[PVU¶JOHUULS!3*93-,3ZZ9ZZ3ZY9ZY
Center
Right (30°)
Left (30°)
Left Surround Side
(90°)
Left Surround Rear
(150°)
Right Surround Rear
(150°)
Right Surround
Side (90°)
LFE
Trigger outputs
;OLV\[W\[ZHYL=MVY6ɈHUK=MVY6UH[\W[VT(;OLJVUULJ[PVUZ
HYLTTTVUVTPUPQHJRZ^P[O[OL[PWHZ[OLV\[W\[YPUNHZNYV\UK
The options are:
4HU\HS :LSLJ[! ;YPNNLY V\[W\[ PZ [VNNSLK 6U6Ɉ I` [OL TH[JOPUN ;YPNNLY
button on the remote control.
-VSSV^:[HUKI`!;OL[YPNNLYV\[W\[^PSSMVSSV^[OL6U6ɈZ[H[\ZVM[OL\UP[
:V\YJLZ!¶;OL[YPNNLYV\[W\[PZSPURLK[VHZWLJPÄJZV\YJL
SW version
All 4 software version numbers need to be stated when contacting Cambridge
Audio customer support.
Update via USB
The CXR software can be updated from the front panel USB socket, which
would normally only be required by a service department or where a network
is not available. Normally user updates will be via a network connection.
Save current settings
Saves settings to internal memory. If the current settings have not been
saved, it is advisable to save the current settings before a software update
is performed.
Load saved settings
Loads the stored settings.
Factory reset
After a factory reset any saved settings can be restored if desired.
Network software update
The CXR can be updated via the StreamMagic module connected to the
internet. Updates of the StreamMagic module itself can only be started from
the Cambridge Connect app or the Web administration interface.
Note: A full update can take over 45 minutes to complete.
Web administration interface
This interface allows the user to:
- Customise the name displayed in the Players list in the Cambridge Connect
app and in the Spotify Connect device list.
- Setup the wireless network connection.
Wired connection *VUULJ[ [OL *?9 [V H ^PYLK UL[^VYR HUK ÄUK [OL 07 HKKYLZZ PU [OL *?9 :L[\W4LU\ CXR Setup Menu Speaker Setup Input Setup Zone 2 Settings Network Setup General Settings HDMI Output Setup Advanced Setup Connection Information Network Selection IP Adress Subnet Mask Gateway DNS1 Ethernet 192.168.0.127 0.0.0.0 0.0.0.0 0.0.0.0 Next Page Use a web browser on the same network to connect to the CXR IP address, eg http://192.168.0.127/ Wireless connection Plug in the supplied wireless antenna to the USB socket on the rear of the CXR. Go to your computer/tablet and click on the Wi-Fi/network logo and select CXR. Use a web browser on your device to connect to http://10.10.10.10/ HDMI output setup cont.