CAME BXE 241 Manual - page 22
22
ITALIANO
- Tenendo premuto
il tasto "CH1" e
dopo l'accensione
del led di segnala-
zione, inviare un
comando con il
tasto del trasmetti-
tore: un breve
lampeggio del led
segnalerà l'avvenu-
ta memorizzazione
(vedi fig.1).
Eseguire la stessa
procedura con il
tasto "CH2" asso-
ciandolo con un'al-
tro tasto del tra-
smettitore (fig.2).
CH1 = Canale per
comandi diretti ad
una funzione della
centralina del
motoriduttore
(comando "solo
apre" / "apre-
chiude-inversione"
oppure "apre-stop-
chiude-stop", a
seconda della
selezione effetuata
sui dip-switch 7,8,9
e 10).
CH2 = Canale per
comandi diretti ad
un dispositivo
accessorio collega-
to su B1-B2.
N.B.: Se in seguito
si vuol cambiare
codice, basta
ripetere la sequenza
descritta.
DEUTSCH
- Die Taste "CH1"
gedrückt halten und
nach Aufleuchten der
Anzeige-Leuchtdiode
über den Sender-
Taster einen
Steuerimpuls
ausführen: ein kurzes
Blinken der Led zeigt
die erfolgte
Speicherung an
(Abb.1).
Gehen Sie ebenso
mit Taste "CH2" vor
und ordnen sie ihr
eine andere Taste
des Senders zu
(Abb.2)
CH1 = Kanal für die
Direktsteuerung einer
Funktion des
Getriebemotor-
Schaltkastens
(Steuerung "nur
Öffnen" / "Öffnen-
Schließen-
Sicherheitsrücklauf"
bzw. "Öffnen-Stp-
Schließen-Stop", je
nach über Dip-Switch
7,8,9 und 10
ausgeführter Wahl).
CH2 = Kanal für
Direktsteuerung
eines über B1-B2
angeschlossenen
Zubehörs.
HINWEIS: bei
eventuell
erwünschter Sender
codeänderung ist der
beschriebene
Vorgang zu
wiederholen.
ESPANOL
- Manteniendo
pulsada la tecla
"CH1" y después
del encendido del
LED de señal con la
tecla del
transmisor: una
breve luz
parpadeante del
LED señalará que la
memorización ha
sido efectuada
(fig.1).
Efectuar el mismo
procedimiento con
la tecla "CH2"
asociándola a otra
tecla del transmisor
(fig.2).
CH1 = Canal para
mando directo a
una función de la
central del
motorreductor
(mando "solo abre"
/ "abre-cierra-
inversión" o "abre-
stop-cierra-stop",
según la selección
efectuada en los
dip-switch 7,8,9 y
10).
CH2 = Canal para
un mando directo a
un dispositivo
accesorio
conectado en B1-
B2.
NOTA: Si posterior-
mente se quisiera
cambiar el código
de los propios
transmisores, sólo
hay que repetir la
secuencia descrita.
ENGLISH
-While holding down
key "CH1", press the
control key on the
transmitter after the
signal LED lights up.
When the key is
pressed, the LED will
flash briefly to signal
that the command
has been stored
(figure 1).
Perform the same
procedure with the
"CH2" key,
associating it with
another transmitter
key (figure 2).
CH1 = Channel for
direct control of one
function performed by
the control unit on the
gear motor ("open
only" / "open-close-
reverse" or "open-
stop-close-stop",
depending on the
position of dip
switches 7,8,9 and
10).
CH2 = Channel for
direct control of an
accessory connected
across B1-B2.
N.B. If you wish to
change the code on
your transmitters in
the future, simply
repeat the procedure
described above.
FRANÇAIS
- En maintenant
appuyée la touche
"CH1" et aprés que
le led de
signalisation s'est
allumé, envoyer une
commande avec la
touche de
l'émetteur: un bref
clignotement du led
signalera que la
mémorisation a été
exécutée. (fig.1).
Suivre la même
procédure avec la
touche "CH2" en
l'associant avec une
autre touche du
emetteur (fig.2).
CH1 = Canal pour
obtenir la
commande directe
d'une fonction du
boîtier du
motoréducteur (
commande
"uniquement ouver-
ture" / "ouverture-
fermeture-
inversion" ou
"ouverte-stop-
ferme-stop" en
fonction de la
sélection effectuée
sur les dip-switchs
7,8,9 et 10).
CH2 = Canal pour
obtenir la
commande directe
d'un dispositif
accessoire branché
sur B1-B2.
N.B.: Si,
successivement, on
veut changer le
code des émetteur,
il suffit de répéter la
séquence décrite ci-
dessus.
MEMORIZZAZIONE CODICE -
CODE STORAGE - MEMORISATION DU CODE
SPEICHERN VOM CODE - MEMORIZACIÓN CÓDIGO
C