Cameo PIXBAR 600 PRO IP65 User manual - page 17
17
Dimmer curves
linear
The light intensity increases linearly with the DMX value.
square / exponential
Adjustment of the light intensity is finer in the lower DMX value range and coarser in the upper DMX value range.
I. square / logarithmic
The light intensity can be adjusted coarsely in the lower DMX value range, and finely in the upper DMX value range.
S-Curve
The adjustment of the light intensity is finer in the lower and upper DMX value ranges and coarser in the middle
DMX value range.
Light intensity
Light intensity
Light intensity
Light intensity
DMX value
linear
square / exponential
I. square / exponential
S-curve
DMX value
DMX value
DMX value
SHOW / ILLUMINA MODE
Select the Show mode to operate the spotlight as an effect spot (e.g. Pixel Control programs) at maximum brightness. An automatic reduction of the
brightness only occurs when the temperature limit is reached.
If the Illumina mode is activated, the spotlight is operated with permanently reduced brightness, in order to ensure a continuous lighting with
constant brightness.
Press the MODE button repeatedly until “Show Mode” or “Illumina Mode” appears on the display. Press the ENTER button and then use the UP and
DOWN buttons to select the desired mode. Confirm the input with ENTER.
DIMMER RESPON (Dimmer response)
The menu item DIMMER RESPONSE offers two possibilities of how the spotlight responds to the DMX value changes.
DIMMER RESPON01: The light reacts abruptly to changes in the DMX value.
DIMMER RESPON02: The light behaves in a manner similar to that of a halogen lamp with gentle changes in brightness.
Press the MODE button repeatedly until “DIMMER RESPON” appears on the display. Press ENTER and then select the desired setting using the UP
and DOWN buttons. Confirm the input with ENTER.
WHITE BALANCE (WHITEBAL)
To achieve a custom white balance, the overall brightness of the colours in the RGBWA and UV operating modes can be adjusted (factory setting =
value 255 for all LEDs) Press the MODE button repeatedly until “WHITEBAL” appears on the display. Press ENTER to now adjust the value for RED
(R: xxx) between 050 to 255 using the UP and DOWN buttons, then press ENTER once more for GREEN (G: xxx), etc.. In this way, the value for each
colour can be adjusted separately. Confirm the input with ENTER.
DMX STARTING ADDRESS AND DMX MODE
Press the MODE button repeatedly until “DMX MODE” appears in the upper line of the display. Press ENTER to place the cursor on the current DMX
address on the bottom line of the display and to make adjustments as desired. Now use the UP and DOWN buttons to select the desired DMX start
address between 001 and 512. Confirm with ENTER. Using the UP and DOWN buttons, one of the 7 different DMX modes can now be selected.
Confirm the input with ENTER. You will find tables with the channels of the different DMX modes on the following pages of this manual.
SLAVE MODE
Press the MODE button repeatedly until “SLAVE MODE” appears on the display. Connect the slave and the master unit (same model) using a DMX
cable and activate one of the standalone modes on the master unit (internal programs, Auto). Now the slave unit follows the master unit.
LOCK FUNCTION
To protect the projector against accidental and unauthorised operation, there is a possibility to lock the controls. Press the UP and DOWN buttons
simultaneously for 5 seconds. The display now shows LOCKED and it is no longer possible to change the settings of the projector using the control
keys. To unlock, press the UP and DOWN buttons simultaneously for 5 seconds. Now the display will change to the previously displayed information.
AUTOLOCK
In addition to the ability to protect the projector manually against accidental or unauthorised operation, this function can also be carried out auto-
matically. Press the MODE button repeatedly until “AUTOLOCK” appears in the upper line of the display. Press ENTER and select “ON” or “OFF” as
required, using the UP and DOWN buttons. Confirm with ENTER.
Select “AUTOLOCK ON” and the controls of the projector are locked automatically after approx. 60 seconds and the lighting of the display goes out.
To unlock, press the UP and DOWN buttons simultaneously for 5 seconds. Now the display will change to the previously displayed information.