- DL manuals
- Camon
- Grinder
- C500
- Operating Instructions Manual
Camon C500 Operating Instructions Manual
Summary of C500
Page 1
C500 stump grinder operating instructions before commissioning the machine, read operating instructions and observe warning and safety instructions..
Page 2: Contents
No liability will be accepted for any damage caused to persons or property through failure to observe the operating and safety instructions. Camon-c500/11.11 contents safety overview ................................................................................................. Page 1 throttle cab...
Page 3: Contents
No liability will be accepted for any damage caused to persons or property through failure to observe the operating and safety instructions. Camon-c500/11.11 contents safety overview ................................................................................................. Page 1 throttle cab...
Page 4: Assembly Instructions
Camon c500 stump grinder camon c500 stump grinder camon-c500/11.11/2 camon-c500/11.11/3 1. Remove the machine from its crate. 2. Remove the handlebar securing pin - part no 11159 (diag no 1, item no 1) . 3. Fit the handlebar with the securing pin and fit split pins part no 960200 (diag no 1, item no...
Page 5: Assembly Instructions
Camon c500 stump grinder camon c500 stump grinder camon-c500/11.11/2 camon-c500/11.11/3 1. Remove the machine from its crate. 2. Remove the handlebar securing pin - part no 11159 (diag no 1, item no 1) . 3. Fit the handlebar with the securing pin and fit split pins part no 960200 (diag no 1, item no...
Page 6: Handbrake Assembly
Camon c500 stump grinder camon c500 stump grinder camon-c500/11.11/4 camon-c500/11.11/5 handbrake assembly 1. Loosen pivot fastener that holds the brake lever to the side plates. 2. Rotate the top side plate to either side so that it is out of the way for the following assembly. 3. Install clamp ont...
Page 7: Handbrake Assembly
Camon c500 stump grinder camon c500 stump grinder camon-c500/11.11/4 camon-c500/11.11/5 handbrake assembly 1. Loosen pivot fastener that holds the brake lever to the side plates. 2. Rotate the top side plate to either side so that it is out of the way for the following assembly. 3. Install clamp ont...
Page 8: Warning
Camon c500 stump grinder camon c500 stump grinder camon-c500/11.11/6 warning ! Transporting the machine the c500 is designed to be transported via a van or small trailer. The machine is equipped with grab bars that are to be used for both lifting the machine, and strapping it down. This machine weig...
Page 9: Warning
Camon c500 stump grinder camon c500 stump grinder camon-c500/11.11/6 warning ! Transporting the machine the c500 is designed to be transported via a van or small trailer. The machine is equipped with grab bars that are to be used for both lifting the machine, and strapping it down. This machine weig...
Page 10: Warning
Camon-c500/11.11/8 camon-c500/11.11/9 camon c500 stump grinder camon c500 stump grinder warning ! Procedure for cutting a stump never leave controls when cutting wheel is rotating! 1. Prepare machine at stump ! Place machine into position with cutting wheel near top edge of stump. Notice before oper...
Page 11: Warning
Camon-c500/11.11/8 camon-c500/11.11/9 camon c500 stump grinder camon c500 stump grinder warning ! Procedure for cutting a stump never leave controls when cutting wheel is rotating! 1. Prepare machine at stump ! Place machine into position with cutting wheel near top edge of stump. Notice before oper...
Page 12: Machine Stopping
Machine stopping 1. When stopping the machine after normal operation, lower engine speed to “slow”, and release operator presence control. A rotating cutting wheel is very dangerous! Stand at controls and ensure that cutting wheel comes to a complete stop before doing anything else. 2. Set park brak...
Page 13: Machine Stopping
Machine stopping 1. When stopping the machine after normal operation, lower engine speed to “slow”, and release operator presence control. A rotating cutting wheel is very dangerous! Stand at controls and ensure that cutting wheel comes to a complete stop before doing anything else. 2. Set park brak...
Page 14: Before Starting The Engine
Camon-c500/11.11/12 camon-c500/11.11/13 camon c500 stump grinder camon c500 stump grinder safety safety before starting the engine 1. Review all of the safety decals that are placed on the machine for your safety and convenience. See parts section for aid in locating all decals on the machine. 2. Ma...
Page 15: Before Starting The Engine
Camon-c500/11.11/12 camon-c500/11.11/13 camon c500 stump grinder camon c500 stump grinder safety safety before starting the engine 1. Review all of the safety decals that are placed on the machine for your safety and convenience. See parts section for aid in locating all decals on the machine. 2. Ma...
Page 16: Brake Adjustment Check
Camon-c500/11.11/14 camon-c500/11.11/15 camon c500 stump grinder camon c500 stump grinder maintenance maintenance for coarse adjustment, loosen lock nuts on hub at lower end of cable. Adjust lock nuts as necessary and re-tighten. 1 1 for fine adjustment, turn brake lever knob clockwise, one revoluti...
Page 17: Brake Adjustment Check
Camon-c500/11.11/14 camon-c500/11.11/15 camon c500 stump grinder camon c500 stump grinder maintenance maintenance for coarse adjustment, loosen lock nuts on hub at lower end of cable. Adjust lock nuts as necessary and re-tighten. 1 1 for fine adjustment, turn brake lever knob clockwise, one revoluti...
Page 18: Sharpening Of Teeth
Maintenance maintenance camon-c500/11.11/16 camon-c500/11.11/17 camon c500 stump grinder camon c500 stump grinder sharpening of teeth do not allow any tooth to wear too much before sharpening. Discard any tooth that has lost more than 3mm of original bite. The teeth must be removed from the cutting ...
Page 19: Sharpening Of Teeth
Maintenance maintenance camon-c500/11.11/16 camon-c500/11.11/17 camon c500 stump grinder camon c500 stump grinder sharpening of teeth do not allow any tooth to wear too much before sharpening. Discard any tooth that has lost more than 3mm of original bite. The teeth must be removed from the cutting ...
Page 20: V-Belt Tension
V-belt tension check drive belts are properly tensioned when 5kg of pressure at the centre of the span produces 4mm deflection. To adjust tension, loosen the engine mounting bolts, loosen the lock nut on the tensioning screw on the front of the frame. Turn the tensioning screw clockwise to increase ...
Page 21: V-Belt Tension
V-belt tension check drive belts are properly tensioned when 5kg of pressure at the centre of the span produces 4mm deflection. To adjust tension, loosen the engine mounting bolts, loosen the lock nut on the tensioning screw on the front of the frame. Turn the tensioning screw clockwise to increase ...
Page 22: Maintenance Overview
Operation 10 hrs or each use 1 st month or 20 hrs 1 st 50 hrs every 3 months or 50 hrs 1 st 100 hrs every 6 months or 100 hrs every year or 300 hrs check engine oil level 10w/40 x x x x x x x fuel tank fill x x x x x x x remove grease and oil build-up x x x x x x x cutter wheel – sharpen or change t...
Page 23: Maintenance Overview
Operation 10 hrs or each use 1 st month or 20 hrs 1 st 50 hrs every 3 months or 50 hrs 1 st 100 hrs every 6 months or 100 hrs every year or 300 hrs check engine oil level 10w/40 x x x x x x x fuel tank fill x x x x x x x remove grease and oil build-up x x x x x x x cutter wheel – sharpen or change t...
Page 24
Tracmaster ltd, sovereign centre, victoria road, burgess hill rh15 9lr t: +44 (0) 1444 247689 f: +44 (0) 1444 871612 w: www.Tracmaster.Co.Uk e: info@tracmaster.Co.Uk © tracmaster ltd 2011. Specifications are subject to change without prior notice..