1. DL manuals
  2. Campbell
  3. Test Equipment
  4. RWIS STATIONS
  5. Instruction Manual

Campbell RWIS STATIONS Instruction Manual

Summary of RWIS STATIONS

  • Page 1

    Instruction manual rwis stations 3/05 c o p y r i g h t ( c ) 2 0 0 5 c a m p b e l l s c i e n t i f i c , i n c ..

  • Page 2: Warranty and Assistance

    Warranty and assistance the rwis stations are warranted by campbell scientific, inc. To be free from defects in materials and workmanship under normal use and service for twelve (12) months from date of shipment unless specified otherwise. Batteries have no warranty. Campbell scientific, inc.'s obli...

  • Page 3: Cs500 Table of Contents

    I cs500 table of contents pdf viewers note: these page numbers refer to the printed version of this document. Use the adobe acrobat® bookmarks tab for links to specific sections. 1. General ........................................................................1 2. Specifications .....................

  • Page 4

    This is a blank page..

  • Page 5: Rwis Stations

    1 rwis stations campbell scientific rwis stations are intended to automatically collect weather and road information. Standard met sensors are used with surface- specific sensors to measure additional site conditions. As with all campbell scientific stations, these are configurable by the customer t...

  • Page 6

    Rwis stations 2 theory of operation the nl110 provides communication for all system devices, converts logger measurements to ntcip compliant data, routes images from an installed camera to the logger, provides snmp communication, and stores text generated in the cr10x to text values required by ntci...

  • Page 7

    Rwis stations 3 loggermap diff channel se channel sensor/color function 12v/color ag/color g/color 1 1h humidity 2l air temp 2 3h open option(oo) 4l wind direction 3 5h solrad 6l solrad 4 7h sub surface 8l sub surface 5 9h sub surface 10l sub surface 6 11h rain y/n(oo)* 12l rainy/n(oo)* p1 wind spee...

  • Page 8

    Rwis stations 4 nl110 setup nl100/105: tlink config: [rs232] rs485 config: [disabled] cs i/o config: [pakbus] cs i/o sdcaddr/bps: [sdc7] cs i/o beacon interval (sec): [60] rs232 config: [ppp] rs232 bps: [38k] ethernet 10base-t: [enabled] 10base-t port ip address: [192.168.7.53] 10base-t port network...

  • Page 9

    Rwis stations 5 dial up setup.

  • Page 10

    Rwis stations 6.

  • Page 11

    Rwis stations 7 collecting the image as data when ftp cannot be used for image removal from the logger, cora_cmd can be. In this case the image is treated just like data in that it is downloaded during a task for routine data removal or by itself in a task. The following batch files are used. The fi...

  • Page 12

    Rwis stations 8.

  • Page 13

    Rwis stations 9.

  • Page 14

    Rwis stations 10 ftp image retrieval to ftp an image from a logger c:\documents and settings\donbrown.Csi-intranet>ftp 192.168.18.150 connected to 192.168.18.150. 220 ftp server ready. User (192.168.18.150:(none)): ntcip 331 password required. Password:ntcip 231 user name accepted. Ftp> get netcam.J...

  • Page 15

    Rwis stations 11 the image is sent to the default directory. Ayantra modem setup ayantra iml560 switch position 1 off 2 on 3 off 4 on 5 off 6 off 7 off 8 on 9 on 10 off 11 off 12 off the modem is set to 38.4kb to match the speed of the serial port on the nl110. Be aware that the power connector of t...

  • Page 16

    Rwis stations 12 blackbox modem setup blackbox md3200a setup for use with rwis stations follow the manual instructions for configuring the modem set the following at&f1 sets the default values ats0=1 answers after 1 ring ats46=136 disables compression at&d0=0 ignores dtr at&w writes the changes netc...

  • Page 17

    Rwis stations 13 troubleshooting there may be times that a partial image is seen. In this case an image was being transferred to the logger, and something interrupted it. Calling in during the image transfer can cause this to happen. Ideally a polled camera would solve this problem since we could as...

  • Page 18

    Rwis stations 14 if there is a time that the station is called but the authentication fails, the nl110 is hung and needs to be reset. This can done locally by using the nl110 configuration menu, or by programming a control port to power rest the modem on a regular interval. The control port is wired...

  • Page 19

    Rwis stations 15 converted to text with the p190 instruction, and text is created also with the p190. This is the set settings instruction, and when using this technique the 68 instruction is used to spell out the text. In both cases the form is variablename=value. There is a limit though to the amo...

  • Page 20

    Rwis stations 16 this is a blank page..

  • Page 21

    This is a blank page..

  • Page 22

    Campbell scientific companies campbell scientific, inc. (csi) 815 west 1800 north logan, utah 84321 united states www.Campbellsci.Com info@campbellsci.Com campbell scientific africa pty. Ltd. (csaf) po box 2450 somerset west 7129 south africa www.Csafrica.Co.Za sales@csafrica.Co.Za campbell scientif...