1. DL manuals
  2. Can-Am
  3. Offroad Vehicle
  4. DS250
  5. Operator's Manual

Can-Am DS250 Operator's Manual

Summary of DS250

  • Page 1

    2 1 9 0 0 0 7 3 5.

  • Page 2: Warning

    Warning your vehicle can be hazardous to operate. A collision or rollover can occur quickly if you fail to take proper precautions, even during routine maneuvers such as turning and driving on hills or over obstacles. For your safety, understand and follow all the warnings contained in this operator...

  • Page 3: Foreword

    Foreword congratulations on your purchase of a new can-am™ atv. It is backed by the brp warranty and a network of autho- rized can-am dealers ready to provide the parts, service or accessories you may require. Your dealer is committed to your sat- isfaction. He has taken training to per- form the in...

  • Page 4: Warning

    Foreword the descriptions and/or specifications in this guide may occur. Brp reserves the right at any time to discontinue or change specifications, designs, fea- tures, models or equipment without incurring any obligation upon itself. This operator's guide and the safety dvd should remain with the ...

  • Page 5: Table Of Contents

    Table of contents foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 know before you go . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 6

    Table of contents controls/instruments/equipment (cont’d) 6) multifunction switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 7) indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 7

    Table of contents maintenance procedures (cont’d) fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 8

    Table of contents 6 _______________.

  • Page 9: Safety

    Safety information ________ safety information ________ 7.

  • Page 10: General Precautions

    General precautions avoid carbon monoxide poisoning all engine exhaust contains carbon monoxide, a deadly gas. Breathing car- bon monoxide can cause headaches, dizziness, drowsiness, nausea, confu- sion and eventually death. Carbon monoxide is a colorless, odor- less, tasteless gas that may be prese...

  • Page 11: Special Safety Messages

    Special safety messages this vehicle is not a toy and can be hazardous to operate. – this vehicle handles differently from other vehicles including motorcycles and cars. A collision or rollover can occur quickly if you fail to take proper precau- tions, even during routine maneuvers such as turning ...

  • Page 12

    Special safety messages – always follow proper procedures for climbing hills as described further in this operator's guide. Check the terrain carefully before you start up any hill. Never climb hills with excessively slippery or loose surfaces. Shift your weight forward. Never open the throttle sudd...

  • Page 13

    Special safety messages – never modify this vehicle through improper installation or use of accessories. Use only brp's approved accessories. Never install passenger a seat. – any load carried on the vehicle will affect the stability and control of the vehi- cle. Never exceed the stated load limits ...

  • Page 14: Operation Warnings

    Operation warnings the following warning and their format have been requested by the united states consumer product safety commission and are required to be in the operator's guide for all atvs. Note: the following illustrations are general representations only. Your model may differ. Warning v00a0a...

  • Page 15: Warning

    Operation warnings warning v00a01q potential hazard failure to follow the age recommendations for this vehicle. What can happen a lack of respect for this age recommendation can lead to severe injury or death of the child. Even though a child may be within the age group for which this vehicle is rec...

  • Page 16: Warning

    Operation warnings warning v00a02q potential hazard carrying a passenger on this vehicle. What can happen greatly reduces your ability to balance and control this vehicle. Could cause an accident, resulting in harm to you and/or your passenger. How to avoid the hazard never carry a passenger. Even w...

  • Page 17: Warning

    Operation warnings warning v00a03q potential hazard operating this vehicle on paved surfaces. What can happen the tires are designed for off-road use only, not for use on pavement. Paved surfaces may seriously affect handling and control of this vehicle, and may cause the vehicle to go out of contro...

  • Page 18: Warning

    Operation warnings warning v00a04q potential hazard operating this vehicle on public streets, roads or highways. What can happen you can collide with another vehicle. How to avoid the hazard never operate this vehicle on any public street, road or highway, even a dirt or gravel one. In many states o...

  • Page 19: Warning

    Operation warnings warning v00a06q potential hazard riding this vehicle without wearing an approved helmet, eye protection and protective clothing. What can happen the following items concern all atv's operator: – riding without an approved helmet increases the chances of a severe head injury or dea...

  • Page 20: Warning

    Operation warnings warning v00a07q potential hazard riding this vehicle after consuming alcohol or drugs. What can happen could seriously affect your judgment. Could cause you to react more slowly. Could affect your balance and perception. Could result in an accident or death. How to avoid the hazar...

  • Page 21: Warning

    Operation warnings warning v00a08q potential hazard operating this vehicle at excessive speeds. What can happen increases your chances of losing control of the vehicle, which can result in an accident. How to avoid the hazard always travel at a speed which is proper for the terrain, visibility and o...

  • Page 22: Warning

    Operation warnings warning v00a09q potential hazard attempting wheelies, jumps and other stunts. What can happen increases the chance of an accident, including an overturn. How to avoid the hazard never attempt stunts, such as wheelies or jumps. Do not try to show off. Warning potential hazard failu...

  • Page 23: Warning

    Operation warnings warning potential hazard riding on frozen waterways. What can happen severe injury or death can result if the vehicle and/or operator break through the ice. How to avoid the hazard never ride this vehicle on a frozen surface before you are sure the ice is thick enough and sound en...

  • Page 24: Warning

    Operation warnings warning v00a0cq potential hazard failure to use extra care when operating this vehicle on unfamiliar terrain. What can happen you can come upon hidden rocks, bumps, or holes, without enough time to react. Could result in the vehicle overturning or loss of control. How to avoid the...

  • Page 25: Warning

    Operation warnings warning v00a0dq potential hazard failure to use extra care when operating on excessively rough, slippery or loose terrain. What can happen could cause loss of traction or vehicle control, which could result in an acci- dent, including an overturn. How to avoid the hazard do not op...

  • Page 26: Warning

    Operation warnings warning v00a0eq potential hazard turning improperly. What can happen vehicle could go out of control, causing a collision or overturn. How to avoid the hazard always follow proper procedures for turning as described further in this op- erator's guide. Practice turning at low speed...

  • Page 27: Warning

    Operation warnings warning v00aqq potential hazard operating on excessively steep hills. What can happen the vehicle can overturn more easily on extremely steep hills than on level surfaces or small hills. How to avoid the hazard never operate this vehicle on hills too steep for the vehicle or for y...

  • Page 28: Warning

    Operation warnings warning v00a0fq potential hazard climbing hills improperly. What can happen could cause loss of control or cause vehicle to overturn. How to avoid the hazard always follow proper procedures for climbing hills as described further in this operator's guide. Always check the terrain ...

  • Page 29: Warning

    Operation warnings warning v00a0gq potential hazard going down a hill improperly. What can happen could cause loss of control or cause vehicle to overturn. How to avoid the hazard always follow proper procedures for going down hills as described further in this operator's guide. Note: a special tech...

  • Page 30: Warning

    Operation warnings warning v00a0hq potential hazard improperly crossing hills or turning on hills. What can happen could cause loss of control or cause vehicle to overturn. How to avoid the hazard never attempt to turn the vehicle around on any hill until you have mastered the turning technique as d...

  • Page 31: Warning

    Operation warnings warning v00a0iq potential hazard stalling, rolling backwards or improperly dismounting while climbing a hill. What can happen could result in vehicle overturning. How to avoid the hazard use proper gear and maintain steady speed when climbing a hill. If you lose all forward speed:...

  • Page 32: Warning

    Operation warnings warning v00a0jq potential hazard improperly operating over obstacles. What can happen could cause loss of control or a collision. Could cause the vehicle to overturn. How to avoid the hazard before operating in a new area, check for obstacles. Never attempt to ride over large obst...

  • Page 33: Warning

    Operation warnings warning v00a0kq potential hazard skidding or sliding improperly. What can happen you may lose control of this vehicle. You may also regain traction unexpectedly, which may cause the vehicle to overturn. How to avoid the hazard learn to safely control skidding or sliding by practic...

  • Page 34: Warning

    Operation warnings warning v00a0lq potential hazard operating this vehicle through deep or fast flowing water. What can happen tires may float, causing loss of traction and loss of control, which could lead to an accident. How to avoid the hazard never operate this vehicle in fast flowing water or i...

  • Page 35: Warning

    Operation warnings warning v00a0mq potential hazard improperly operating in reverse. What can happen you could hit an obstacle or person behind the vehicle, resulting in serious injury. How to avoid the hazard when you select reverse gear, make sure there are no obstacles or people behind the vehicl...

  • Page 36: Warning

    Operation warnings warning v00a0oq potential hazard operating this vehicle with improper tires, or with improper or uneven tire pressure. What can happen use of improper tires on this vehicle, or operation of this vehicle with improper or uneven tire pressure, may cause loss of control, tire blow ou...

  • Page 37: Warning

    Operation warnings warning v00a0nq potential hazard operating this vehicle with improper modifications. What can happen improper installation of accessories or modification of this vehicle may cause changes in handling which in some situations could lead to an acci- dent. How to avoid the hazard nev...

  • Page 38: Warning

    Operation warnings warning v00a0pq potential hazard overloading this vehicle, carrying or towing cargo improperly. What can happen could cause changes in vehicle handling which could lead to an accident. How to avoid the hazard never exceed the stated load capacity for this vehicle including operato...

  • Page 39: Warning

    Operation warnings warning v03m01q potential hazard transporting flammable or dangerous material can lead to explosions. What can happen this can cause serious injury or death. How to avoid the hazard never transport flammable or dangerous material. ________ safety information ________ 37.

  • Page 40: Riding The Vehicle

    Riding the vehicle while reading this operator’s guide, remember that: warning indicates a potential hazard that, if not avoided, could result in serious injury or death. To fully appreciate the pleasures and excitement of riding this vehicle, there are some basic rules and tips that you must follow...

  • Page 41: Pre-Ride Inspection

    Riding the vehicle pre-ride inspection warning perform a pre-ride inspection before each ride to detect any potential prob- lem that could occur during operation. The pre-ride inspection can help you monitor component wear and deterioration before they become a problem. Correct any problems that you...

  • Page 42

    Riding the vehicle items to be inspected inspection to perform ✔ if you transport a cargo, respect the load capacity. Ensure cargo is properly secured to the racks cargo if you are pulling a trailer or an other equipment: – check hitch and trailer ball condition – respect the tongue capacity and tow...

  • Page 43: Clothing

    Riding the vehicle what to do after the engine is started items to be inspected inspection to perform ✔ indicator lamps ensure engine oil/temperature indicator lamp is off (shut engine off if light remains on) transmission lever check operation of transmission lever (f, n and r) brakes drive forward...

  • Page 44: Carrying A Passenger

    Riding the vehicle boots long, sturdy pants gloves long sleeves rigid chin guard eye protection chest protector v00a0rn approved helmet carrying a passenger this vehicle is designed specifically to carry an operator only. Even with a long seat, this vehicle is not designed nor intended to carry pass...

  • Page 45: Working With Your Vehicle

    Riding the vehicle safely reduce speed according to terrain conditions when carrying cargo or pulling a trailer. Allow greater distance for braking. Always secure cargo as low as possi- ble on the rack(s) to reduce the effect of a higher center of gravity. Maximum load total load allowed 150 kg (330...

  • Page 46: Environment

    Riding the vehicle before you ride, tell someone where you are planning to travel and your expected time of return. Depending on the length of your ride, carry additional tools or emergency equip- ment. Find out where you can get additional gasoline and oil. Be prepared for the possible conditions y...

  • Page 47: Off-Road Operation

    Riding the vehicle off-road operation the very nature of off-road operation is dangerous. Any terrain, which has not been specially prepared to carry vehicles, presents an inherent danger where angularity, terrain substance and exact steepness are unpredictable. The terrain itself presents a continu...

  • Page 48: Warning

    Riding the vehicle it is also wise to know the terrain condition on the other side of the hill or bank. All too often there exists a sharp drop-off that is impossible to negotiate or descend. Downhill driving this vehicle can climb slopes that are steeper than it can safely descend. There- fore, it ...

  • Page 49: Riding Techniques

    Riding the vehicle as you drive your atv over a loose snow covered surface, snow dust will be picked up in the wake turbulence of the moving vehicle and transported to contact and accumulate or melt on some exposed components including rotating parts like brake discs. Water, snow or ice may affect t...

  • Page 50

    Riding the vehicle at all times. Do not direct your toes outwards nor extend your feet out to assist in turning as they can be hit or get snagged by passing obstacles, or may come into contact with the wheels. V00a0ul even though there is an adequate suspensions system on this vehicle there are “was...

  • Page 51

    Riding the vehicle v00a0vl water will affect the braking ability of your vehicle. Make sure you dry the brakes by applying them several times after the vehicle leaves the water. Mud or marsh lands may be encountered near water. Be prepared for sudden “holes” or changes in depth. Similarly so, be wat...

  • Page 52

    Riding the vehicle when riding in sand dunes it is advisable to equip the vehicle with an antenna type safety flag. This will help make your location more visible to others over the next sand dune. Proceed carefully should you see another safety flag ahead. Since the antenna type safety flag can sna...

  • Page 53

    Riding the vehicle uphill keep your body weight forward towards the top of the hill. Keep your feet on the footpegs and shift into low gear then accelerate and when necessary, change gear quickly as you climb. Do not over-speed since this may cause the front of the vehi- cle to lift from the ground ...

  • Page 54: Warning

    Riding the vehicle v00a0yl side hilling this is one of the most risky types of riding since it may drastically change the bal- ance of the vehicle. It should be avoided wherever possible. However, if it is nec- essary to do so, it is important that you always keep your body weight on the up- side of...

  • Page 55: Hang Tag

    Important on product labels hang tag this vehicle comes with hang tags and labels containing important safety informa- tion. Any person who rides this vehicle should read and understand this information be- fore riding. This atv is for recreational use or utility use g general use model • with a pas...

  • Page 56: Vehicle Safety Labels

    Important on product labels vehicle safety labels read and understand all the safety la- bels on your vehicle. The safety labels on your vehicle should be considered permanent parts of the vehicle. If missing or damaged, they can be replaced free of charge. See an authorized can-am dealer. Note: the...

  • Page 57

    Important on product labels vmo2010-001-401_c right rear fender label never use under the influence of drugs or alcohol. Vmo2009-003-004_en label 1 v01m02z label 2 v01m07z label 3 vmo2006-007-002_aen label 4 ________ safety information ________ 55.

  • Page 58

    Important on product labels v06m0ey label 5 vmo2010-004-002_en label 6 vmo2010-010-100_a label 7 ce vÉhicule est un vÉhicule tout terrain qui n’est pas destinÉ a Être utilisÉ sur les voies publiques. This vehicle is an all terrain vehicle and is not intended for use on public roads. 704901438 vmo201...

  • Page 59: Compliance Labels

    Important on product labels compliance labels these labels indicate vehicle's compli- ance. V00m03y location: right front lower tube of the frame vmo2010-001-302_a location: underneath rear fender vmo2010-004-001_en location: front fender technical information label vmo2006-014-002_aen drive chain a...

  • Page 60: This Page Is

    Important on product labels this page is intentionally blank 58 _______ safety information ________.

  • Page 61: Vehicle

    Vehicle information _______________ 59.

  • Page 62

    Controls/instruments/equipment note: some controls/instruments/equipment are optional. 10 13 3 7 4 2 5 11 9 8 12 6 7 1 5 vmo2009-002-003_c 60 ______________.

  • Page 63: 1) Throttle Lever

    Controls/instruments/equipment note: this section provides basic information on the functions of the var- ious controls, instruments and equip- ment available on your vehicle. Illus- trations used in this operator's guide may not be exact representations, your model may differ. For more details of h...

  • Page 64: 4) Parking Brake

    Controls/instruments/equipment when pulled in, the rear brake is ap- plied. When released, it should auto- matically return to its original position. Braking effect is proportional to the force applied on the lever. Vmo2011-001-004_a typical 1. Brake lever 2. To apply brake 4) parking brake the park...

  • Page 65: Warning

    Controls/instruments/equipment vmo2006-014-024_b transmission lever pattern 1. Forward (f) 2. Neutral (n) 3. Reverse (r) to change the transmission lever po- sition, completely stop vehicle, apply brakes, then move lever to the desired position. Do not force lever. Note: any shifting attempt at high...

  • Page 66: Warning

    Controls/instruments/equipment vmo2011-001-005_a typical — headlights switch functions 1. Headlights switch 2. Low beam and taillight 3. High beam and taillight 4. Off position emergency engine stop switch this switch can be used to stop the en- gine and as an emergency control. Note: while the engi...

  • Page 67: 7) Indicator Lamps

    Controls/instruments/equipment vmo2011-001-005_b typical 1. Override button choke lever this device features a variable position lever used to ease starting a cold en- gine. The off position is used when the en- gine is warm. V06f0py choke lever in the off position the full choke position is used wh...

  • Page 68: 8) Ignition Switch

    Controls/instruments/equipment engine temperature (red) this light comes on every time the ignition switch is turned on, and remains on for approximately 1 second. When this indicator light is on during engine operation, it indicates the engine is overheating. If the engine overheats, refer to engin...

  • Page 69: 10) Brake Pedal

    Controls/instruments/equipment vmo2006-014-013_a 1. Align the pointer toward the desired position 2. Res. (reserve) 3. Off 4. On off stops fuel supply to carburetor. Notice turn valve to off position when vehicle is not being operated or when transporting. On allows fuel to flow to carburetor. This ...

  • Page 70: 12) Seat Latch

    Controls/instruments/equipment 12) seat latch located underneath the rear fender, it allows the removal of the seat to gain access to the service compartment. Vmo2006-014-016_a seat removal unlock seat using latch lever. Gently lift rear of seat while pulling rear- ward to release. Vmo2006-014-017_a...

  • Page 71: Warning

    Controls/instruments/equipment an auxiliary supply is available to con- nect additional accessories. Two wires are hidden in the wiring harness at the rear of vehicle. See an authorized can-am dealer for details. While reading this operator’s guide, remember that: warning indicates a potential hazar...

  • Page 72: Fuel

    Fuel recommended fuel use unleaded gasoline available from most service stations, or oxygenated fuel containing a maximum of 10% ethanol or methanol. The gasoline used must have the following recom- mended minimum octane rating. Minimum octane rating inside north america 87 (r + m)/2 outside north a...

  • Page 73: Warning

    Fuel 5. Pour fuel slowly to allow time for the air in the tank time to escape and prevent fuel flow back. Be care- ful not to spill fuel. 6. Stop fuelling when the fuel reaches the bottom of filler neck. Do not overfill. 7. Fully tighten fuel tank cap clock- wise. Vmo2006-014-012_a 1. Fuel tank cap ...

  • Page 74: Break-In Period

    Break-in period operating during break-in a break-in period of 10 operating hours is required before running the vehicle at sustained full throttle. After the break-in period, the vehicle should be inspected by an authorized can-am dealer. Refer to mainte- nance information . Brakes warning new brak...

  • Page 75: Operating Instructions

    Operating instructions starting the engine conditions required for engine starting 1. Transmission lever must be set to neutral. 2. Emergency engine stop switch set to run position. 3. Key in ignition switch and turned to the on position. 4. Engine start button pressed in. Initial cold starting inse...

  • Page 76: Shifting The Transmission

    Operating instructions off position. Start the engine with- out activating the throttle lever. After a few seconds, set the choke lever to off position. Shifting the transmission let engine idle to warm up. Apply brakes and set the transmission selector lever to ”f” (forward), or "r" (reverse). Rele...

  • Page 77: Tune Your Ride

    Tune your ride suspension adjustment warning adjust both front springs to the same length. Uneven adjustment can cause poor handling and loss of stability and/or control, and in- crease the risk of an accident. Spring preload may vary from rider to rider depending upon their weight. Preload can be c...

  • Page 78: Vehicle Transportation

    Vehicle transportation when transporting this vehicle, secure it to a trailer or in pickup box using suit- able tie-downs. The use of ordinary ropes is not recommended. Warning do not tow this vehicle behind a car or other vehicle. Use a trailer. Never tip this vehicle on end when transporting it . ...

  • Page 79: Maintenance

    Maintenance _______________ 77.

  • Page 80: Break-In Inspection

    Break-in inspection brp suggests that after the first 10 hours or 200 km (125 mi) of operation, whichever comes first, your vehicle be inspected by an authorized can-am dealer. The break-in inspection is very important and must not be neglected. Note: the break-in inspection is at the expense of the...

  • Page 81

    Break-in inspection replace adjust tighten lubricate clean break-in inspection chart inspect fuel system fuel filter x fuel lines, connections, and fuel tank pressure test x throttle lever and cable x x carburetor x choke x electrical system spark plug x x ignition timing x battery x wiring harnesse...

  • Page 82: Maintenance Schedule

    Maintenance schedule maintenance is very important for keeping your vehicle in safe operating condition. Proper maintenance is the owner's responsibility. The vehicle should be serviced as specified in the maintenance schedule. The maintenance schedule does not exempt the pre-ride inspection. Warnin...

  • Page 83

    Maintenance schedule maintenance schedule 25 h or 500 km (300 mi) 50 h or 1 000 km (600 mi) 100 h or 1 year or 2 000 km (1,200 mi) 200 h or 2 years or 4 000 km (2,500 mi) a: adjust c: clean i: inspect l: lubricate r: replace to be performed by part/task legend cvt transmission drive belt i dealer dr...

  • Page 84

    Maintenance schedule maintenance schedule 25 h or 500 km (300 mi) 50 h or 1 000 km (600 mi) 100 h or 1 year or 2 000 km (1,200 mi) 200 h or 2 years or 4 000 km (2,500 mi) a: adjust c: clean i: inspect l: lubricate r: replace to be performed by part/task legend steering handlebar fasteners i dealer s...

  • Page 85: Maintenance Procedures

    Maintenance procedures this section includes instructions for basic maintenance procedures. If you have the necessary mechanical skills and the required tools, you can per- form these procedures. If not, see your authorized can-am dealer. Other important items in the mainte- nance schedule that are ...

  • Page 86

    Maintenance procedures vmo2006-014-046_a 1. Clamp 2. Retaining screw air filter cleaning 1. Spray the foam filter element inside and out with air filter cleaner (p/n 219 700 341). 219700341 air filter cleaner (p/n 219 700 341) vbs2009-012-015_a typical - spray foam element inside and out 2. Let stan...

  • Page 87: Air Filter Housing

    Maintenance procedures 219700340 air filter oil (p/n 219 700 340) vbs2009-012-014 typical - oil foam filter element notice engine performance degradation or severe damage can occur if the air filter is not properly maintained and/or if it is not well oiled. Air filter installation properly reinstall...

  • Page 88: Engine Oil

    Maintenance procedures engine oil recommended engine oil for the summer season, use xps synthetic blend oil (summer grade) (p/n 293 600 121). For the winter season, use xps synthetic oil (winter grade) (p/n 293 600 112). Note: the xps oil is specially formu- lated and tested for the severe require- ...

  • Page 89

    Maintenance procedures vmo2006-014-019_a rh side of engine with vehicle on a level surface and en- gine cold, not running, check the oil level as follows: 1. Unscrew dipstick then remove it and wipe clean. 2. Reinstall dipstick (do not screw it in). 3. Remove and check oil level. It should be near o...

  • Page 90: Oil Strainer

    Maintenance procedures refill engine with the specified quan- tity of the recommended engine oil. Refer to technical specifica- tions for capacity. Note: engine oil quantity is also writ- ten on the dipstick. Start engine and let idle for a few min- utes. Ensure oil strainer and drain plug are not l...

  • Page 91: Engine Coolant

    Maintenance procedures if available, use a garden hose to rinse the radiating fins. Caution never clean radiator with your hands when it is hot. Let the radiator cool down before clean- ing. Notice be careful not to damage the radiating fins when cleaning. Do not use any object/tool that could damag...

  • Page 92: Warning

    Maintenance procedures vmo2006-014-015_a step 1: pull front tab from grommets step 2: lift cover to remove add coolant up to max. Mark if re- quired. Use a funnel to avoid spillage. Do not overfill. Properly reinstall and tighten filler cap. Reinstall front fender access cover. If the coolant is add...

  • Page 93

    Maintenance procedures unscrew the cooling system drain plug located on the right side of engine and drain the coolant into a suitable con- tainer. Vmo2006-014-040_a 1. Cooling system drain plug disconnect the by-pass hose from the top of the thermostat housing. Vmo2006-014-041_a 1. By-pass hose dra...

  • Page 94: Spark Arrester

    Maintenance procedures install radiator cap. Inspect all connec- tions for leaks and check coolant level in the reservoir. Install access cover. Spark arrester spark arrester cleaning the muffler must be periodically purged of accumulated carbon. Warning never perform this operation im- mediately af...

  • Page 95: Drive Belt

    Maintenance procedures while holding one half of the valve, turn the other half counterclockwise to open it. Vmo2006-014-073_a 1. Filters pour air filter cleaner (p/n 219 700 341) or an equivalent into a bucket. Put filters in to soak. While the filters soak, clean inside the air injection valve. Ri...

  • Page 96: Throttle Cable

    Maintenance procedures gearbox oil change place the vehicle on a level surface. Remove the drive chain protector. Vmo2006-014-038_a 1. Drive chain protector clean fill and drain plug areas. Remove gearbox fill plug. Place a drain pan under the gearbox drain plug area then remove the drain plug. Vmo2...

  • Page 97: Warning

    Maintenance procedures warning always use a silicone-based lu- bricant. Using another lubricant (such as a water-based lubricant) could cause the throttle lever/ cable to stick or become stiff. Open the throttle lever housing. Vmo2006-014-051_a 1. Remove screws slide the rubber protector to expose t...

  • Page 98: Spark Plug

    Maintenance procedures note: if correct adjustment is unattainable, see an authorized can-am dealer. The normal throttle free-play is 1 mm to 3 mm (.039 in to .118 in). Note: measure throttle free play at the tip of throttle lever. To adjust cable, slide rubber protector back to expose throttle cabl...

  • Page 99: Battery

    Maintenance procedures torque spark plugs to 11 n•m ± 1.1 n•m (97 lbf•in ± 10 lbf•in). Battery to access the battery, remove the seat. Battery maintenance caution never charge a bat- tery while installed in vehicle. These vehicles are equipped with a vrla battery (valve regulated lead acid). It is a...

  • Page 100: Lights

    Maintenance procedures a15e0ky 1 2 1. Fuse 2. Check if melted note: the fuse rating and the circuit it protects is illustrated on the fuse holder cover. Lights headlights headlight bulb replacement notice never touch the glass portion of a halogen bulb with bare fingers, it shortens its operating li...

  • Page 101: Drive Chain And Sprockets

    Maintenance procedures vmo2008-018-037 typical instal new bulb, do not touch the glass portion of the new bulb with bare fin- gers. Check light operation after bulb re- placement. Properly reinstall removed parts in the reverse order of their removal. Beam aiming adjustment to adjust the headlight b...

  • Page 102

    Maintenance procedures caution ensure the engine is off and the parking brake is en- gaged before checking, adjusting or lubricating the drive chain. Notice never operate this vehi- cle with the drive chain too loose or too tight as severe damage to the drive components can occur. Drive chain and sp...

  • Page 103: Tires And Wheels

    Maintenance procedures vmo2006-014-059_a 1. Caliper support bolt insert adjuster lock through sprocket hub and into chain tensioner. Vmr2006-084-004_a 1. Drive chain 2. Adjuster lock 3. Sprocket hub 4. Chain tensioner adjust chain deflection by slowly mov- ing the vehicle forward or backward. The de...

  • Page 104: Wheel Bearing

    Maintenance procedures although the tires are specifically de- signed for off-road use, a flat may still occur. Therefore, it is recommended to carry a tire pump and a repair kit. Tire and wheel condition check tire for damage and wear. Re- place if necessary. Do not rotate tires. The front and rear...

  • Page 105: Suspension

    Maintenance procedures suspension suspension lubrication swing arm lubricate swing arm pivots. Use synthetic suspension grease (p/n 293 550 033) or an equivalent. Vmo2006-014-061_a lh side of vehicle 1. Cvt duct 2. Grease fitting suspension inspection shock absorbers inspect shock absorbers for oil ...

  • Page 106: Warning

    Maintenance procedures vmr2006-085-004 typical — lh rear brake fluid reservoir rear brake fluid reservoir with vehicle on a level surface, brake fluid should be between min. And max. Level marks. Vmo2006-014-032 underneath rh rear fender brake fluid replacement warning brake fluid replacement should...

  • Page 107: Vehicle Care

    Vehicle care post-operation care when the vehicle is used in a salt wa- ter environment, rinsing the vehicle with fresh water is necessary to pre- serve the vehicle and its components. Lubrication of metal parts is highly rec- ommended. Use xps lube (p/n 293 600 016) or an equivalent. This must be p...

  • Page 108: Warning

    Storage and preseason preparation warning have an authorized can-am dealer inspect the fuel system integrity as specified in maintenance schedule . When a vehicle is not in use for a period of four months, proper storage is a ne- cessity. See an authorized can-am dealer for proper procedures. When u...

  • Page 109: Technical

    Technical information ______________ 107.

  • Page 110: Vehicle Identification

    Vehicle identification the main components of your vehicle (engine and frame) are identified using different serial numbers. It may sometimes become necessary to locate these numbers for warranty purposes or to trace your vehicle in the event of loss. These numbers are also required by the authorize...

  • Page 111

    Vehicle identification engine identification number location vmo2006-014-005_a ______________ 109.

  • Page 112

    Ddd2009-001 the ec-declaration of conformity does not appear in this version of the operator's guide. Please refer to the printed version that was delivered with your vehicle. En.

  • Page 113: Specifications

    Specifications vehicle model ds 250 engine type 4-stroke. Single overhead camshaft engine, liquid cooled number of cylinders single cylinder number of valves 4 valves with mechanical lifters (adjustable) displacement 249.4 cm³ (15.2 in³) bore 71 mm (2.8 in) stroke 63 mm (2.5 in) starting system elec...

  • Page 114

    Specifications vehicle model ds 250 electrical system magneto generator type 338 w @ 5000 rpm ignition type cdi (capacitor discharge ignition) ignition timing not adjustable make ngk type cr8e gap 0.8 mm (.031 in) spark plug quantity 1 type wet type battery battery volt 12 volts, 10 a•h (ampere hour...

  • Page 115

    Specifications vehicle model ds 250 tires front pressure rear maximum: 34 kpa (5 psi) minimum: 26 kpa (3.8 psi) front 22 x 7–10 size rear 20 x 11–9 wheels front at 10 x 5.5 size rear at 9 x 8 wheel nut torque 50 n•m ± 5 n•m (37 lbf•ft ± 4 lbf•ft) brakes front hydraulic, 2 discs rear hydraulic, 1 dis...

  • Page 116

    Specifications vehicle model ds 250 fluids engine oil for the summer season, use xps synthetic blend oil (summer grade) (p/n 293 600 121) . For the winter season, use xps synthetic oil (winter grade) (p/n 293 600 112) . Refer to oil viscosity chart gearbox oil xps chaincase oil (p/n 415 129 500) or ...

  • Page 117: Troubleshooting

    Troubleshooting ______________ 115.

  • Page 118: Troubleshooting Guidelines

    Troubleshooting guidelines engine does not crank 1. Ignition switch is in the off position. – place switch to the on position. 2. Emergency engine stop switch. – make sure the emergency engine stop switch is in the run position. 3. Transmission is not set to neutral. – set transmission either in neu...

  • Page 119

    Troubleshooting guidelines engine turns over but fails to start (cont’d) 4. Spark plug/ignition (no spark). – check main fuse condition. – remove spark plug from engine and reconnect it to the spark plug cap. – ensure the ignition switch is set to on and the emergency engine stop switch is set to th...

  • Page 120

    Troubleshooting guidelines engine overheats (cont’d) 2. Dirty radiator fins. – clean radiator fins, check radiator in maintenance information. Engine backfire 1. Exhaust system leakage. – contact an authorized can-am dealer. 2. Engine is running too hot. – see engine lacks acceleration or power. 3. ...

  • Page 121

    Troubleshooting guidelines vehicle cannot reach full speed (cont’d) 2. Parking brake. – ensure brake lever lock is completely disengaged. 3. Air filter/housing clogged or dirty. – check air filter and clean if necessary. – check deposits in air filter housing drain. – check the position of the air i...

  • Page 122

    Troubleshooting guidelines 120 ______________.

  • Page 123: Warranty

    Warranty ______________ 121.

  • Page 124: Can-Am

    Brp limited warranty usa and canada: 2011 can-am tm atv 1) scope of the limited warranty bombardier recreational products inc. (“brp”)* warrants its 2011 can-am atv sold by authorized can-am atv dealers (as hereinafter defined) in the fifty united states and canada from defects in material or workma...

  • Page 125

    – damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by brp or resulting from repairs done by a person that is not an authorized servicing can-am atv dealer; – damage caused by abuse, abnormal use, neglect or o...

  • Page 126: 7) What Brp Will Do

    – the 2011 can-am atv must be purchased in the country in which the purchaser resides; – routine maintenance outlined in the operator’s guide must be timely per- formed in order to maintain warranty coverage. Brp reserves the right to make warranty coverage contingent upon proof of proper maintenanc...

  • Page 127: 8) Supplier Warranties

    8) supplier warranties a gps receiver may be supplied by brp as standard equipment on certain 2011 can-am atv's. The gps receiver is covered by the limited warranty issued by the gps receiver’s manufacturer and is not covered by this limited warranty. Please contact the following distributors if in ...

  • Page 128: 10) Consumer Assistance

    10) consumer assistance in the event of a controversy or a dispute in connection with this limited warranty, brp suggests that you try to resolve the issue at the dealership level. We recom- mend discussing the issue with the authorized dealer's service manager or owner. If the issue has not yet bee...

  • Page 129: Can-Am

    Brp international limited warranty: 2011 can-am tm atv 1) scope of the limited warranty bombardier recreational products inc. (“brp”)* warrants its 2011 can-am atv sold by can-am atv distributors or dealers authorized by brp to distribute can-am atvs ("can-am atv distributor/dealer") outside of the ...

  • Page 130

    – damage caused by failure to provide proper maintenance and/or storage, as de- scribed in the operator's guide; – damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by brp or resulting from repairs done by a p...

  • Page 131: 7) What Brp Will Do

    Brp will not honor this limited warranty to any private use owner or commercial use owner if the preceding conditions have not been met. Such limitations are necessary in order to allow brp to preserve both the safety of its products, and also that of its consumers and the general public. 6) what to...

  • Page 132: 9) Consumer Assistance

    9) consumer assistance 1. In the event of a controversy or a dispute in connection with this limited warranty, brp suggests that you try to resolve the issue at the can-am atv dealer level. We recommend discussing the issue with the service manager or owner. You will find your can-am atv distributor...

  • Page 133: Atv

    Brp limited warranty for the european economic area: 2011 can-am tm atv 1) scope of the limited warranty bombardier recreational product inc. (“brp”)* warrants its new and unused model-year 2011 can-am atvs sold by can-am atv distributors or dealers au- thorized by brp to distribute can-am atvs ("ca...

  • Page 134

    – damage caused by failure to provide proper maintenance and/or storage, as de- scribed in the operator's guide; – damage resulting from removal of parts, improper repairs, service, mainte- nance, modifications or use of parts not manufactured or approved by brp or resulting from repairs done by a p...

  • Page 135: 7) What Brp Will Do

    – the product must have undergone proper registration by an authorized can-am atv distributor/dealer; – the 2011 can-am atv must be purchased in the eea; and – routine maintenance outlined in the operator’s guide must be timely per- formed in order to maintain warranty coverage. Brp reserves the rig...

  • Page 136: 8) Transfer

    8) transfer if the ownership of a product is transferred during the warranty coverage period, this limited warranty shall also be transferred and be valid for the remaining cover- age period provided brp or an authorized can-am atv distributor/dealer receives a proof that the former owner agreed to ...

  • Page 137

    For all other countries, please contact your local can-am atv distributor/dealer (visit our website at www.Brp.Com for contact information), or contact our north america office at: bombardier recreational products inc. Customer assistance center 75 j.-a. Bombardier street sherbrooke qc j1l 1w3 tel.:...

  • Page 138: France Only

    Additional terms and conditions for france only the following terms and conditions are applicable to products sold in france only: the seller shall deliver goods that are complying with the contract and shall be re- sponsible for defects existing upon delivery. The seller shall also be responsible f...

  • Page 139: Customer

    Customer information ______________ 137.

  • Page 140: Privacy Information

    Privacy information brp wishes to inform you that your coordinates will be used for safety and war- ranty related purposes. Furthermore, brp and its affiliates may use its customer list to distribute marketing and promotional information about brp and related products. To exercise your right to cons...

  • Page 141

    Change of address/ownership if your address has changed or if you are the new owner of the atv, be sure to no- tify brp by either: – mailing one of the change of address cards on the following pages – north america only: calling at 715 848-4957 (usa) or 819 566-3366 (canada) – notifying an authorize...

  • Page 142: This Page Is

    Change of address/ownership this page is intentionally blank 140 ______________.

  • Page 143

    Change of address/ownership ______________ 141.

  • Page 144

    Change of address/ownership 142 ______________.

  • Page 145

    Change of address/ownership ______________ 143.

  • Page 146

    Change of address/ownership 144 ______________.

  • Page 147

    Atv model no. Vehicle identification number (v.I.N.) engine identification number (e.I.N.) owner: purchase date year month day warranty expiry date year month day to be completed by the dealer at the time of the sale. Dealer imprint area name no. Street apt citystate/province zip/postal code v00a2il...

  • Page 148

    2 1 9 0 0 0 7 3 5.