Cannondale 2012 IQ300 Setup And Owners Manual - page 2
2012 IQ300 Computer
Setup and Owners Manual - 11/11
NOTE: This computer can record information for 2 bikes with different wheel sizes. This
allows you to use 1 computer for 2 bikes. Shortly after the wheel rotates, the computer
automatically knows which bike is being used then provides accurate information for
speed and mileage. A mounting kit for a 2nd bike is sold separately. The following steps
only need to be done once.
To start programming:
1. Press FUNCTION until “ODO” displays.
2. Press and hold SET for >3 seconds to begin programming.
3. Press SET to change to “kM/H” or “M/H”
To program the computer for bike #1:
4. Determine your Tire Size then find the corresponding L (mm) in the chart below.
5. Press SET to select bike 1 “ ”
6. Press FUNCTION to move the cursor to the first field.
7. Press SET to change the 1st digit of 4 numbers for the L (mm).
Repeat steps 6 and 7 until the proper L (mm) is entered.
If you will use this computer for 2 bikes, continue to step 8.
If you will use it for only 1 bike, continue to step 10.
To program the computer for bike #2:
8. Determine your Tire Size then find the corresponding L (mm) in the chart below.
9. Press FUNCTION to select bike 2 “ ”
Repeat steps 6 and 7 until the proper L (mm) is entered.
10. Press and hold FUNCTION for 3 seconds to exit programming.
SETTING THE CLOCK (CLK)
1. Press FUNCTION until the “CLK” function shows.
2. Press and hold SET for >3 seconds to begin programming.
3. Press SET to change to “12H” or “24H” hour mode.
4. Press the FUNCTION to move the cursor to the hour field
5. Press SET hour.
6. Repeat steps 4 and 5 to set Minutes and Seconds.
7. Press and hold the FUNCTION button for 3 seconds to exit programming.
GENERAL NOTES FOR PROGRAMMING ALL FUNCTIONS:
•
Press and hold SET for 3 seconds to begin programming a function.
•
Press the SET to change the value of a selected field. Press/hold SeT to change
value rapidly.
•
Press the FUNCTION button to move the cursor to the next field.
•
Press and hold the FUNCTION button for 3 seconds to exit programming.
SETTING THE WHEEL SIZE
L (mm)
Tire Size
L (mm)
Tire Size
L (mm)
24 X 1.75
1890
27 X 1-3/8
2169
24 X 2.00
1925
650 X 20C
1938
24 X 2.125
1965
650 X 23C
1944
26 X 7/8
1920
650 X 35A
2090
26 X 1(59)
1913
650 X 38A
2125
26 X 1(65)
1952
650 X 38b
2105
26 X 1.25
1953
700 X 18C
2070
Tire Size
L (mm)
26 X 1-1/8
1970
700 X 19C
2080
14 X 1.50
1020
26 X 1-3/8
2068
700 X 20C
2086
14 x 1.75
1055
26 X 1-1/2
2100
700 X 23C
2096
16 X 1.50
1185
26 X 1.40
2005
700 X 25C
2105
16 X 1.75
1195
26 X 1.50
2010
700 X 28C
2136
18 X 1.50
1340
26 X 1.75
2023
700 X 30C
2146
18 X 1.75
1350
26 X 1.95
2050
700 X 32C
2155
20 X 1.75
1515
26 X 2.00
2055
700C Tubular
2130
20 X 1-3/8
1615
26 X 2.10
2068
700 X 35C
2168
22 X 1-3/8
1770
26 X 2.125
2070
700 X 38C
2180
22 X 1-1/2
1785
26 X 2.35
2083
700 X 40C
2200
24 X 1
1753
26 X 3.00
2170
29 X 2.1
2288
24 X 3/4 Tubular
1785
27 X 1
2145
29 X 2.3
2326
24 x 1-1/8
1795
27 X 1-1/8
2155
24 X 1-1/4
1905
27 X 1-1/4
2161
To begin using the computer, simply press the FUNCTION button. Following installation,
the computer is activated automatically by a rotating wheel.
There are 2 power saving modes - 50% savings if no movement after 5 minutes, 100%
power savings after 30 minutes.
Press the SET button to exit the power saving modes prior to using the computer.
Press the FUNCTION button, to switch the computer through the following functions:
“CLK” – Clock feature, in 12/24 hr format
“TM” – Time ridden for 1 ride
“AVS” – Average speed for 1 ride
“MXS” – Maximum speed for 1 ride
“DST” - Distance ridden for 1 ride
“ODO” – Total miles ridden for all rides
“KCAL” – Calories burned (estimate) for 1 ride
“DAILY” -- DIstance ridden in the past 24 hours
“ODO 1” -- Total miles for all rides, bike 1 “ ”
“ODO 2” -- Total miles for all rides, bike 2 “ ”
To turn on the backlight, press and release the SET button. The backlight will stay
on for three (3) seconds.
“TM, AVS, MXS, DST, and kCAL “ are recorded automatically as soon as the wheel moves.
Recording stops if the wheel stops. To clear this information, press and hold the SET
button in the “TM” mode.
Main DiSpLay anD FuncTionS
CR
20
32
touch
SET Button
(back of unit)
**This button also,
activates the display
backlighting.
CURRENT SPEED
SPEED SCALE
MODE
FUNCTIONS DISPLAY
FUNCTION Button
SUB-DISPLAY
TEMPERATURE
MOTION SIGNAL
BIKE “I or BIKE “II”
SLEEP MODE