Canon 0583B002 - Pixma MP830 Office All-In-One Inkjet Printer Start Here
Start Here
Easy Setup Instructions
Unpack the machine
Please confi rm bundled thing by the illustration printed on the fl apped lid of the packing box.
QT5-0226-V01
Hardware setup and Print Head
alignment is complete.
If you are connecting the machine to a computer for
use, see the back side of this sheet for instructions on
installing the software.
For fax users
To send a fax, you need to set the
telephone line type setting properly on
the machine.
You have a dedicated telephone line for
fax use only:
→ FAX only
You receive mainly voice calls and
sometimes faxes, and you want to receive
faxes manually:
→ Manual RX
You want to receive voice messages on
your answering machine, and receive
faxes automatically:
→ Ans. machine connect.
You want to switch faxes and voice calls
automatically:
→ FAX/TEL auto switch
You have subscribed to a Distinctive Ring
Pattern Detection (DRPD) service with your
telephone company:
→ DRPD
For details about the receive mode
setting, refer to “Receiving Faxes” in the
User’s Guide.
If you are unsure of your telephone line
type, contact your telephone company.
Cassette Loading
You can load paper in both the Auto Sheet Feeder
and Cassette.
1
Pull out the Cassette from the bottom
of the machine.
Cassette
2
Load the stack of paper into the
Cassette with the print side face
down. Pinch the Paper Guide and
align it to the stack.
AB
Paper
Guide
1
Remove the shipping tape from the
machine.
IMPORTANT
Make sure to remove the protective fi lm from the
Feeder Cover.
2
Unlock the Scanner Lock Switch.
IMPORTANT
• Make sure to unlock it before turning the machine on.
• Before transporting the machine, always lock the Scan-
ning Unit (Printer Cover) by moving the Scanner Lock
Switch towards the lock mark.
3
Connect the telephone line and any
necessary external device.
Connect the telephone
line cord to the wall jack.
You can connect an external device
(telephone or answering machine) if necessary.
Connect external devices as follows:
External device jack
Telephone line jack
Telephone or answering machine
Built-in computer modem and telephone
Telephone
line
Telephone
line
Machine
Machine
Telephone or
answering machine
Telephone
Computer
LINE TEL
IMPORTANT
Be sure to use the bundled telephone line cable.
4
Plug the power cord into the back of
the machine and connect the other
end to a power outlet. Press [ON/OFF].
1
Prepare the machine
2
Install the Print Head
3
Install the ink tanks
4
Align the Print Head
5
Use [ ] or [ ] on the Operation
Panel to select the language for the
LCD, then press [OK].
(1) Press [ ] or [ ] to
select the language.
(2) Press [OK].
If the message tank.> appears, go to 6 . 6 Press the Open button to open the Paper Output Tray. Open up and set the Paper Output Tray extension by pressing down the hollow on its front side. Paper Output Tray Open Button 7 Open the Scanning Unit (Printer Cover) until it locks into place. The Print Head Holder moves to the center. Scanning Unit (Printer Cover) IMPORTANT Be careful not to touch the buttons on the Operation Panel. 8 Open the Inner Cover. Write down the serial number located inside the machine. You will need this to register your products. Inner Cover Serial Number Location 1 Remove the Print Head from its package. CAUTION There might be some transparent or light blue ink on the inside of the bag the print head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. 2 Remove the orange protective cap from the Print Head and discard it. Do not touch the Print Head nozzles and the electrical contacts. Print Head Nozzles Electrical Contacts Protective Cap 3 Firmly raise the Print Head Lock Lever until it stops. 4 Insert the Print Head. Do not touch! 5 Lower the Print Head Lock Lever carefully and press it down. IMPORTANT If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center. 1 Peel back the orange tab completely and remove the plastic wrapper from the ink tank. If the orange-colored protective fi lm is not removed completely, problems with printing may occur. 2 Twist off and discard the orange protective cap located on the bottom of the ink tank. Electrical Contacts ink port Protective Cap Do not press! IMPORTANT • Do not touch the electrical contacts. • Do not touch the ink port. 3 Insert the ink tank into the right-hand slot. 4 Press the mark on the ink tank until it clicks into place and then its lamp lights red. Refer to the color guide on the Print Head Lock Lever. Click 5 Close the Inner Cover and the Scanning Unit (Printer Cover). Click IMPORTANT For safety, always fi rmly grip the areas illustrated when closing the Scanning Unit (Printer Cover). 1 Open the Paper Support, then pull out the extension. Pinch the Paper Guide and slide it to the left. Paper Support Extension Paper Guide 2 Load a few sheets of letter- or A4-size paper into the Auto Sheet Feeder, align the paper with the right side of the Cover Guide, then slide the Paper Guide toward the left edge of the paper. Print Side Paper Guide Cover Guide 3 Ensure that the message requesting head alignment is displayed on the LCD, select and press [OK]. The pattern is printed. And Print Head is aligned automatically. OK • The pattern is printed in black and blue. • Print Head alignment will take several minutes to complete. Do not start another operation here. • When automatic Print Head alignment cannot be executed correctly, the message displayed on the LCD. Refer to “An Error Message is Displayed on the LCD” in the User’s Guide.