1. DL manuals
  2. Connect Tech
  3. Adapter
  4. Xtreme/104 Opto
  5. User Manual

Connect Tech Xtreme/104 Opto User Manual

Other manuals for Xtreme/104 Opto: User Manual
Manual is about: Serial Communications Adapter

Summary of Xtreme/104 Opto

  • Page 1

    Xtreme/104 opto pc/104 serial communications adapter user manual connect tech inc 42 arrow road guelph, ontario n1k 1s6 tel: 519-836-1291 toll: 800-426-8979 (north america only) fax: 519-836-4878 email: sales@connecttech.Com support@connecttech.Com url: www.Connecttech.Com ctim-00007, revision 0.05,...

  • Page 2

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 2 limited lifetime warranty connect tech inc. Provides a lifetime warranty for all connect tech inc. Products. Should this.

  • Page 3

    Xtreme/104 opto user’s manual, connect tech inc. 3 revision 0.05 certification xtreme/104 opto the xtreme/104 opto product family is to be included into a device ultimately subject to fcc, doc/ic, and ce certification. The customer is responsible for bringing the completed device into compliance pri...

  • Page 4

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 4 table of contents limited lifetime warranty ..............................................................................................................................2 copyright notice .................................................

  • Page 5

    Xtreme/104 opto user’s manual, connect tech inc. 5 revision 0.05 list of figures figure 1: xtreme/104 opto, 2 port model...................................................................................................... 8 figure 2: xtreme/104 opto, 4 port model.......................................

  • Page 6

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 6 customer support overview if you experience difficulties after reading the manual and/or using the product, contact the connect tech reseller from which you purchased the product. In most cases the reseller can help you with product in...

  • Page 7

    Xtreme/104 opto user’s manual, connect tech inc. 7 revision 0.05 introduction xtreme/104 opto adapters are high performance multi-port serial adapters for pc/104 stacks that enable you to connect up to four serial devices per board. Each port is optically isolated from each other and from the board ...

  • Page 8

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 8 xtreme/104 opto components figure 1: xtreme/104 opto, 2 port model figure 2: xtreme/104 opto, 4 port model rs-232 enable/ tx & rx control/ tx & rx terminators/ jumper blocks jb4, jb5 pin 10 pin 1 pin 10 pin 1 jb4 jb5 jb2 p5 p4 ports 1 ...

  • Page 9

    Xtreme/104 opto user’s manual, connect tech inc. 9 revision 0.05 hardware installation installing the xtreme/104 opto into your system before you begin, take a minute to ensure that your package includes the required components that should have shipped with your xtreme/104 opto. • one xtreme/104 opt...

  • Page 10

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 10 custom port addresses you can generate other port addresses by making changes to the cplds found on the xtreme/104 opto adapter. If you require specific port addresses not listed in table 1 please contact a connect tech customer servi...

  • Page 11

    Xtreme/104 opto user’s manual, connect tech inc. 11 revision 0.05 mode 1 (one irq): 1. Ensure there are no jumpers across positions e and d on the jb3 jumper block. 2. All ports interrupt on one irq by setting jumpers on the a or c rows and the middle rows of jumper blocks jb1 or jb2. Mode 2 (two ir...

  • Page 12

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 12 figure 4: interrupt (irq) selection jumper setting examples example: mode 3 – two irqs (xtreme/104 opto, 4 port model only) in the following example, ports 1 and 2 are set to interrupt on irq 7 and ports 3 and 4 interrupt on irq 10. J...

  • Page 13

    Xtreme/104 opto user’s manual, connect tech inc. 13 revision 0.05 baud rate selection the xtreme/104 opto is capable of baud rates up to 460.8 kbps (4x oscillator) or 115.2 kbps (1x oscillator) depending on whether a shorting block is installed across position g on the jb3 jumper block. Please refer...

  • Page 14

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 14 software installation xtreme/104 opto adapters are standard multi-port serial adapters that utilize 16c2850 uarts. In many cases, users have software that will interface directly to the xtreme/104 opto adapters. Many operating systems...

  • Page 15

    Xtreme/104 opto user’s manual, connect tech inc. 15 revision 0.05 specifications operating environment storage temperature: -65 ° c to 150° c operating temperature: 0 ° c to 70° c (standard version) -40 ° c to 85° c (extended temperature version) humidity: 0 to 90% relative humidity, non-condensing ...

  • Page 16

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 16 connectors/pinouts table 3: p4/p5/p6/p7 - 10 pin port header pinouts pin no. Rs-232 direction direction direction 1 nc nc rxd (+) input 2 nc nc cts (-) input 3 rxd input rxd (-) input 4 rts output rts (+) output 5 txd output txd (+) o...

  • Page 17

    Xtreme/104 opto user’s manual, connect tech inc. 17 revision 0.05 table 4: db-9 cable connector pinouts pin no. Rs-232 signal direction rs-422/485 signal direction 1 nc nc rxd (+) input 2 rxd input rxd (-) input 3 txd output txd (+) output 4 nc nc txd (-) output 5 isolated gnd signal gnd isolated gn...

  • Page 18

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 18 rs-232/rs-422/485 interfaces electrical interface selection the xtreme/104 opto adapter provides jumper selectable rs-232 and rs-422/485 electrical interfaces on each port. Jumper blocks jb4, jb5, jb6 and jb7 set the electrical interf...

  • Page 19

    Xtreme/104 opto user’s manual, connect tech inc. 19 revision 0.05 full duplex mode if you wish to run the individual rs-422/485 ports in full duplex mode, do not install jumpers across positions a and c of jumper blocks jb4, jb5, jb6 and jb7. In this mode, transmit and receive are active all the tim...

  • Page 20

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 20 figure 8: half duplex mode jumper setting example in the following example, ports 1 and 2 are set for half duplex mode. Ports 3 and 4 are rs-232 and therefore should not be set for half duplex. Jb4 jb5 jb6 jb7 j1 jumper is on j1 j2 ju...

  • Page 21

    Xtreme/104 opto user’s manual, connect tech inc. 21 revision 0.05 line termination use jumper blocks jb4, jb5, jb6 and jb7 to terminate and bias txd ±, rxd ±, rts ±, and cts ± on the individual rs-422/485 ports through jumper selectable 150 ohm fixed resistors. Please note that revisions a and b of...

  • Page 22

    Xtreme/104 opto user’s manual, connect tech inc. Revision 0.05 22 figure 11: line bias and termination jumper setting example in this example, port 1 is set for half duplex rs-422/485, terminated and biased on cts ± and rxd ±. Port 2 is set for full duplex rs-422/48, bias/termination on rts ±, txd ±...

  • Page 23

    Xtreme/104 opto user’s manual, connect tech inc. 23 revision 0.05 rs-422/485 cable wiring examples figure 12: rs-422/485 wiring diagram (4 wire) rts + rts - cts + cts - txd + txd - rxd + rxd - rxd + txd + rxd - txd - rts - cts - rts + cts + sr sr xtreme/104 opto adapter rs-485/422 peripheral 3 4 2 5...