Xa 10a/10a-d manual 1.2 en.
S y m b o l s o n t h e p r o d u c t p l e a s e r e f e r t o t h e i n f o r m a t i o n i n t h e m a n u a l . W a r n i n g ! D a n g e r o u s v o l t a g e ! General information 10a/10a-d manual version: 1.2 en, 02/2016, d2610.En .01 copyright © 2016 by d&b audiotechnik gmbh; all rights rese...
1. Safety precautions........................................................... 4 1.1. Information regarding the use of loudspeakers.................... 4 2. 10a/10a-d loudspeaker............................................... 5 2.1. Product description.................................................
1.1. Information regarding the use of loudspeakers potential risk of personal injury never stand in the immediate vicinity of loudspeakers driven at a high level. Professional loudspeaker systems are capable of causing a sound pressure level detrimental to human health. Seemingly non-critical sound ...
2.1. Product description the 10s, 10a and 10al and their "d versions" are a family of high performance 2-way loudspeakers employing a single 10” driver in a bass-reflex enclosure and different hf sections for a wide range of installed sound applications. All models are lightweight passive designs us...
2.2. Connections the cabinets are fitted with a pair of nl4 connectors and a two pole screw terminal block (st). All four pins of both nl4 connectors are wired in parallel. The cabinets use the pin assignments 1+/1–. Pins 2+/2– are designated to active subwoofers. Cabinets with the weather resistant...
Nl4 connection with cover plate the two nl4 connector sockets of the cabinet's connector panel are located in a recess to allow the use of the cover plate [1] together with nl4 cable connectors, as shown in the graphic opposite. Note: neutrik nl4fc type connectors must be used for this option. The c...
Hfa circuit in hfa mode (high frequency attenuation), the hf response of the system is rolled off. Hfa provides a natural, balanced frequency response when a unit is placed close to listeners in near field or delay use. High frequency attenuation begins gradually at 1 khz, dropping by approximately ...
2.4. Dispersion characteristics the following graphs show dispersion angle over frequency of a single cabinet plotted using lines of equal sound pressure (isobars) at –6 db and –12 db. Fig. 8: isobar diagram horizontal 10a vertical setup fig. 9: isobar diagram vertical fig. 10: isobar diagram horizo...
Fig. 12: isobar diagram horizontal 10a-d vertical setup fig. 13: isobar diagram vertical fig. 14: isobar diagram horizontal 10a-d horizontal setup, horn rotated fig. 15: isobar diagram vertical altering the hf horn dispersion the hf horn can be rotated through 90°. Tools required: philips screwdrive...
2.5. Technical specifications 10a/10a-d system data frequency response (–5 db standard) 60 hz - 18 khz frequency response (–5 db cut mode) 100 hz - 18 khz max. Sound pressure (1 m, free field) with 10d/d6 127 db with 30d/d20/d12 130 db with d80 130 db (splmax peak, pink noise test signal with crest ...
3.1. Eu conformity of loudspeakers (ce symbol) this declaration applies to: d&b 10a loudspeaker, z1555 d&b 10a-d loudspeaker, z1556 manufactured by d&b audiotechnik gmbh. All production versions of these types are included, provided they correspond to the original technical version and have not been...
D2610.En .01, 02/2016 © d&b audiotechnik gmbh www.Dbaudio.Com.