S series this saw can be operated safely only when the operating instructions have been completely read and strictly adhered to. It is recommended operation manual ta-070 wet tile saw for your safety.
To receive practical instruction before using the saw for the first time. Always inspect cable and plug before using the saw. The outlet must be grounded. Ground fault circuit interrupter (gfci) protection should be provided on the circuit(s) or outlet(s) to be used for this saw. Have damage repaire...
Z keep work area well lit. Z avoid body contact with earthed or grounded surfaces (e.G. Pipes, radiators, ranges, refrigerators). Z do not let persons, especially children, not involved in the work touch the tool or the extension cord and keep them away from the work area. Z when not in use, tools s...
For your safety z to avoid the possibility of the appliance plug or receptacle getting wet, position tile saw to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. The user should arrange a trip loop in the cord connecting the saw to a receptacle. The d...
Innovation put to work here at d cut products, inc. We are always looking to come out with new innovative products. Check out our website for updates at www.Dcutproducts.Com or contact us at sales@dcutproducts.Com for your (90 day) warranty to be effective on all electrical motor and parts such as t...
6 fig.1 fig. 2 fig. 3 0-90°attachment----1p press mechanism------2p operation manual--- 1p warranty card------- --1p steel stand open folded stand in a flat area. Contents in the box: wench-------------- - - ----1p installation press down wheel brakes as shown. Set the saw onto the 4pins of the stan...
Fig.4 open the table remove all tools, debris etc. From the saw table. Lock the side plate in position and lift the table allowing the rod from the concave recesses molded into the tray. This enables the saw table to remain in the open when storing the saw always turn the stand 90 degree to keep it ...
Fig.1 0 图 8 fig. 9 cutting: insert a piece of tile under the guide rails and keep a flat and straight side against the gauge. Use the clap to hold the tile. Stand along the saw/table comfortably and start the saw and push the saw towards the tile. Fill the water tray with approx.5 gallons (23liters)...
Clean drain the water by pulling the chain attached to the plug on the bottom of the water tray. Use the provided scraper to clean and remove the cutting debris and slurry and pour a bucket of clean water throughout the water reservoir tray. Fig.1 3 fig.1 2 0-90 °attachment (1) unlock the screw on t...
Warning: if it is not needed please don’t adjustment the twos screws. Setting accuracy （1） adjustment the two screws as shown in fig.16 the verticality of the gauge and the blade can be regulated if it is needed. Fig.1 6 fig.1 7 warning: if it is not needed, please don’t adjustment the twos screws. ...
11.
Parts description q’t parts description q’t 1 water tray 1 35 inner hex screw m5 ×25 1 2 inner hex screwm6 ×20 2 36 flat washer 5mm 2 3 hex nut m6 2 37 inner hex screw m5 ×40 1 4 laser head assembly 1 38 belt cover 1 5 cross screw m4 ×10 2 39 inner hex screw m6 ×20 2 6 flat washer 4mm 2 40 big flat ...
B. Make sure working piece is flush against the gauge. 2. Motor doesn’t work a. Check power source connection. B. Check power cords for damage. 3. Table vibration during cutting process a. Check blade installation. B. Check blade-wearing status. 4. Losing cutting speed a. Stop work and allow the mot...
Environmental protection waste electrical products should not be disposed of with household waste. Please recycle where facilities exit. Check with your local authority or retailer for recycling advice. D cut products, inc. 1041n. Lombard road lombard, il 60148 usa tel: 630-916-9100 fax: 630-916-910...
