1. DL manuals
  2. D-Link
  3. Switch
  4. DES-3010FA
  5. Cli Manual

D-Link DES-3010FA Cli Manual - Sntp Trusted-Key

Other manuals for DES-3010FA: Web User Manual, Cli Manual
Manual is about: Layer 2 Switch, 8 Port 10/100 802.3af PoE Managed Switch Plus (1)Gigabit Copper and (1)SFP Interface

Summary of DES-3010FA

  • Page 2: Table of Contents

    D-link des-3010fa/ga cli reference guide page 1 table of contents section 1. Using the cli..................................................................................................... 10 1.1 cli command modes.......................................................................................

  • Page 3

    Table of contents page 2 show ports security ............................................................................................................... 45 section 4. Clock.................................................................................................................. 47 clock ...

  • Page 4

    D-link des-3010fa/ga cli reference guide page 3 show interfaces configuration ............................................................................................... 86 show interfaces status .......................................................................................................

  • Page 5

    Table of contents page 4 clear host ............................................................................................................................ 125 clear host dhcp.................................................................................................................... 126...

  • Page 6

    D-link des-3010fa/ga cli reference guide page 5 section 15. Port monitor commands.................................................................................. 157 port monitor...........................................................................................................................

  • Page 7

    Table of contents page 6 section 19. Snmp commands........................................................................................... 197 snmp-server community...................................................................................................... 197 snmp-server view ............

  • Page 8

    D-link des-3010fa/ga cli reference guide page 7 name (mst).......................................................................................................................... 242 revision (mst) .......................................................................................................

  • Page 9

    Table of contents page 8 terminal data-dump ............................................................................................................. 283 show history ........................................................................................................................ 284 show...

  • Page 10

    D-link des-3010fa/ga cli reference guide page 9 dot1x timeout re-authperiod ................................................................................................ 321 dot1x re-authenticate ........................................................................................................

  • Page 11: Section 1. Using The Cli

    Using the cli cli command modes page 10 section 1. Using the cli this chapter describes how to start using the cli and describes implemented command editing features to assist in using the cli. 1.1 cli command modes 1.1.1 introduction to assist in configuring the device, the command line interface (...

  • Page 12

    D-link des-3010fa/ga cli reference guide page 11 the global configuration mode manages the device configuration on a global level. The interface configuration mode configures specific interfaces in the device. 1.1.2 user exec mode after logging into the device, the user is automatically in user exec...

  • Page 13

    Using the cli cli command modes page 12 1.1.4 global configuration mode global configuration mode commands apply to features that affect the system as a whole, rather than just a spe- cific interface. The configure privileged exec mode command is used to enter the global configuration mode. To enter...

  • Page 14: 1.2

    D-link des-3010fa/ga cli reference guide page 13 • mac access-list —configures conditions required to allow traffic based on mac addresses. The mac access-list global configuration mode command is used to enter the mac access-list configuration mode.. 1.2 starting the cli the device can be managed o...

  • Page 15: 1.3

    Using the cli editing features page 14 1.3 editing features 1.3.1 entering commands a cli command is a series of keywords and arguments. Keywords identify a command, and arguments specify configuration parameters. For example, in the command show interfaces status ethernet 8, show, interfaces and st...

  • Page 16

    D-link des-3010fa/ga cli reference guide page 15 1.3.1.2 negating the effect of commands for many configuration commands, the prefix keyword no can be entered to cancel the effect of a command or reset the configuration to the default value. This guide describes the negation effect for all applicabl...

  • Page 17

    Screen display indicates system messages and prompts appearing on the console. All when a parameter is required to define a range of ports or parameters and all is an option, the default for the command is all when no parameters are defined. For exam- ple, the command interface range port-channel ha...

  • Page 18: Section 2. Aaa Commands

    D-link des-3010fa/ga cli reference guide page 17 section 2. Aaa commands aaa authentication login the aaa authentication login global configuration mode command defines login authentication. To return to the default configuration, use the no form of this command. Syntax aaa authentication login {def...

  • Page 19

    Aaa commands page 18 user guidelines the default and optional list names created with the aaa authentication login command are used with the login authentication command. Create a list by entering the aaa authentication login list-name method command for a particular protocol, where list-name is any...

  • Page 20: Aaa Authentication Enable

    D-link des-3010fa/ga cli reference guide page 19 aaa authentication enable the aaa authentication enable global configuration mode command defines authentication method lists for accessing higher privilege levels. To return to the default configuration, use the no form of this command. Syntax aaa au...

  • Page 21

    Aaa commands page 20 example the following example sets the enable password for authentication when accessing higher privilege levels. Console(config)# aaa authentication enable default enable.

  • Page 22: Login Authentication

    D-link des-3010fa/ga cli reference guide page 21 login authentication the login authentication line configuration mode command specifies the login authentication method list for a remote telnet or console. To return to the default configuration specified by the aaa authentication login com- mand, us...

  • Page 23: Enable Authentication

    Aaa commands page 22 enable authentication the enable authentication line configuration mode command specifies the authentication method list when accessing a higher privilege level from a remote telnet or console. To return to the default configuration specified by the aaa authentication enable com...

  • Page 24: Ip Http Authentication

    D-link des-3010fa/ga cli reference guide page 23 ip http authentication the ip http authentication global configuration mode command specifies authentication methods for http server users. To return to the default configuration, use the no form of this command. Syntax ip http authentication method1 ...

  • Page 25: Ip Https Authentication

    Aaa commands page 24 ip https authentication the ip https authentication global configuration mode command specifies authentication methods for https server users. To return to the default configuration, use the no form of this command. Syntax ip https authentication method1 [method2...] no ip https...

  • Page 26: Show Authentication Methods

    D-link des-3010fa/ga cli reference guide page 25 show authentication methods the show authentication methods privileged exec mode command displays information about the authentica- tion methods. Syntax show authentication methods default configuration this command has no default configuration. Comma...

  • Page 27: Password

    Aaa commands page 26 password the password line configuration mode command specifies a password on a line. To remove the password, use the no form of this command. Syntax password password [encrypted] no password parameters • password — password for this level (range: 1-159 characters). • encrypted ...

  • Page 28: Enable Password

    D-link des-3010fa/ga cli reference guide page 27 enable password the enable password global configuration mode command sets a local password to control access to user and privilege levels. To remove the password requirement, use the no form of this command. Syntax enable password [level level] passw...

  • Page 29: Username

    Aaa commands page 28 username the username global configuration mode command creates a user account in the local database. To remove a user name, use the no form of this command. Syntax username name [password password] [level level] [encrypted] no username name parameters • name — the name of the u...

  • Page 30: Bridge Address

    D-link des-3010fa/ga cli reference guide page 29 section 3. Address table commands bridge address the bridge address interface configuration (vlan) mode command adds a mac-layer station source address to the bridge table. To delete the mac address, use the no form of this command. Syntax bridge addr...

  • Page 31: Bridge Multicast Filtering

    Address table commands page 30 bridge multicast filtering the bridge multicast filtering global configuration mode command enables filtering multicast addresses. To dis- able filtering multicast addresses, use the no form of this command. Syntax bridge multicast filtering no bridge multicast filteri...

  • Page 32: Bridge Multicast Address

    D-link des-3010fa/ga cli reference guide page 31 bridge multicast address the bridge multicast address interface configuration (vlan) mode command registers a mac-layer multicast address in the bridge table and statically adds ports to the group. To unregister the mac address, use the no form of thi...

  • Page 33

    Address table commands page 32 bridge multicast forbidden address the bridge multicast forbidden address interface configuration (vlan) mode command forbids adding a spe- cific multicast address to specific ports. Use the no form of this command to return to the default configuration. Syntax bridge ...

  • Page 34: Bridge Multicast Forward-All

    D-link des-3010fa/ga cli reference guide page 33 bridge multicast forward-all the bridge multicast forward-all interface configuration (vlan) mode command enables forwarding all multi- cast packets on a port. To restore the default configuration, use the no form of thiscommand. Syntax bridge multica...

  • Page 35

    Address table commands page 34 bridge multicast forbidden forward-all the bridge multicast forbidden forward-all interface configuration (vlan) mode command forbids a port to be a forward-all-multicast port. To restore the default configuration, use the no form of thiscommand. Syntax bridge multicas...

  • Page 36: Bridge Aging-Time

    D-link des-3010fa/ga cli reference guide page 35 bridge aging-time the bridge aging-time global configuration mode command sets the address table aging time. To restore the default configuration, use the no form of this command. Syntax bridge aging-time seconds no bridge aging-time parameters • seco...

  • Page 37: Clear Bridge

    Address table commands page 36 clear bridge the clear bridge privileged exec mode command removes any learned entries from the forwarding database. Syntax clear bridge default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user...

  • Page 38: Port Security

    D-link des-3010fa/ga cli reference guide page 37 port security the port security interface configuration mode command locks the port, thereby, blocking unknown traffic and preventing the port from learning new addresses. To return to the default configuration, use the no form of this command. Syntax...

  • Page 39

    Address table commands page 38 port security routed secure-address the port security routed secure-address interface configuration (ethernet, port-channel) mode command adds a mac-layer secure address to a routed port. Use the no form of this command to delete a mac address. Syntax port security rou...

  • Page 45

    Address table commands page 44 show bridge multicast filtering the show bridge multicast filtering user exec mode command displays the multicast filtering configuration. Syntax show bridge multicast filtering vlan-id parameters • vlan-id — vlan id value. Default configuration this command has no def...

  • Page 47

    Address table commands page 46 the following tables describes the fields shown above. Ch7 disabled ch8 disabled f i e l d d e s c r i p t i o n port port number status locked/unlocked action action on violation trap indicates if traps are sent in case of a violation frequency minimum time between co...

  • Page 48: Section 4. Clock

    D-link des-3010fa/ga cli reference guide page 47 section 4. Clock clock set the clock set privileged exec mode command manually sets the system clock. Syntax clock set hh:mm:ss day month year or clock set hh:mm:ss month day year parameters • hh:mm:ss — current time in hours (military format), minute...

  • Page 49: Clock Source

    Clock page 48 clock source the clock source global configuration mode command configures an external time source for the system clock. Use no form of this command to disable external time source. Syntax clock source {sntp} no clock source parameters • sntp — sntp servers default configuration no ext...

  • Page 50: Clock Timezone

    D-link des-3010fa/ga cli reference guide page 49 clock timezone the clock timezone global configuration mode command sets the time zone for display purposes. To set the time to the coordinated universal time (utc), use the no form of this command. Syntax clock timezone hours-offset no clock timezone...

  • Page 51: Clock Summer-Time

    Clock page 50 clock summer-time the clock summer-time global configuration mode command configures the system to automatically switch to summer time (daylight saving time). To configure the software not to automatically switch to summer time, use the no form of this command. Syntax clock summer-time...

  • Page 52

    D-link des-3010fa/ga cli reference guide page 51 user guidelines in both the date and recurring forms of the command, the first part of the command specifies when summer time begins, and the second part specifies when it ends. All times are relative to the local time zone. The start time is relative...

  • Page 53: Sntp Authentication-Key

    Clock page 52 sntp authentication-key the sntp authentication-key global configuration mode command defines an authentication key for simple net- work time protocol (sntp). To remove the authentication key for sntp, use the no form of this command. Syntax sntp authentication-key number md5 value no ...

  • Page 54: Sntp Authenticate

    D-link des-3010fa/ga cli reference guide page 53 sntp authenticate the sntp authenticate global configuration mode command grants authentication for received simple network time protocol (sntp) traffic from servers. To disable the feature, use the no form of this command. Syntax sntp authenticate no...

  • Page 55: Sntp Trusted-Key

    Clock page 54 sntp trusted-key the sntp trusted-key global configuration mode command authenticates the identity of a system to which sim- ple network time protocol (sntp) will synchronize. To disable authentication of the identity of the system, use the no form of this command. Syntax sntp trusted-...

  • Page 56: Sntp Client Poll Timer

    D-link des-3010fa/ga cli reference guide page 55 sntp client poll timer the sntp client poll timer global configuration mode command sets the polling time for the simple network time protocol (sntp) client. To return to default configuration, use the no form of this command. Syntax sntp client poll ...

  • Page 57: Sntp Broadcast Client Enable

    Clock page 56 sntp broadcast client enable the sntp broadcast client enable global configuration mode command enables simple network time protocol (sntp) broadcast clients. To disable sntp broadcast clients, use the no form of this command. Syntax sntp broadcast client enable no sntp broadcast clien...

  • Page 58: Sntp Anycast Client Enable

    D-link des-3010fa/ga cli reference guide page 57 sntp anycast client enable the sntp anycast client enable global configuration mode command enables sntp anycast client. To disable the sntp anycast client, use the no form of this command. Syntax sntp anycast client enable no sntp anycast client enab...

  • Page 59

    Clock page 58 sntp client enable (interface) the sntp client enable interface configuration (ethernet, port-channel, vlan) mode command enables the sim- ple network time protocol (sntp) client on an interface. This applies to both receive broadcast and anycast updates. To disable the sntp client, us...

  • Page 60: Sntp Unicast Client Enable

    D-link des-3010fa/ga cli reference guide page 59 sntp unicast client enable the sntp unicast client enable global configuration mode command enables the device to use the simple net- work time protocol (sntp) to request and accept sntp traffic from servers. To disable requesting and accepting sntp t...

  • Page 61: Sntp Unicast Client Poll

    Clock page 60 sntp unicast client poll the sntp unicast client poll global configuration mode command enables polling for the simple network time protocol (sntp) predefined unicast servers. To disable the polling for sntp client, use the no form of this com- mand. Syntax sntp unicast client poll no ...

  • Page 62: Sntp Server

    D-link des-3010fa/ga cli reference guide page 61 sntp server the sntp server global configuration mode command configures the device to use the simple network time protocol (sntp) to request and accept sntp traffic from a specified server. To remove a server from the list of sntp servers, use the no...

  • Page 63: Show Clock

    Clock page 62 show clock the show clock user exec mode command displays the time and date from the system clock. Syntax show clock [detail] parameters • detail — shows timezone and summertime configuration. Default configuration this command has no default configuration. Command mode user exec mode ...

  • Page 64: Show Sntp Configuration

    D-link des-3010fa/ga cli reference guide page 63 show sntp configuration the show sntp configuration privileged exec mode command shows the configuration of the simple network time protocol (sntp). Syntax show sntp configuration default configuration this command has no default configuration. Comman...

  • Page 65: Show Sntp Status

    Clock page 64 show sntp status the show sntp status privileged exec mode command shows the status of the simple network time protocol (sntp). Syntax show sntp status default configuration this command has no default configuration. Command mode privilegedexec mode user guidelines there are no user gu...

  • Page 66: Copy

    D-link des-3010fa/ga cli reference guide page 65 section 5. Configuration and image files copy the copy privileged exec mode command copies files from a source to a destination. Syntax copy source-url destination-url parameters • source-url — the source file location url or reserved keyword of the s...

  • Page 67

    Configuration and image files page 66 some invalid combinations of source and destination exist. Specifically, you cannot copy if one of the following conditions exist: the source file and destination file are the same file. Xmodem: is the destination file. The source file can be copied to image, bo...

  • Page 68

    D-link des-3010fa/ga cli reference guide page 67 example the following example copies system image file1 from the tftp server 172.16.101.101 to a non-active image file. Console# copy tftp://172.16.101.101/file1 image accessing file 'file1' on 172.16.101.101... Loading file1 from 172.16.101.101: !!!!...

  • Page 69: Delete

    Configuration and image files page 68 delete the delete privileged exec mode command deletes a file from a flash memory device. Syntax delete url parameters • url — a reserved keyword of the file to be deleted. (range: 1-160 characters) the following table displays the reserved keyword: default conf...

  • Page 70: Delete Startup-Config

    D-link des-3010fa/ga cli reference guide page 69 delete startup-config the delete startup-config privileged exec mode command deletes the startup-config file. Syntax delete startup-config default configuration this command has no default configuration. Command mode privilegedexec mode user guideline...

  • Page 71: Show Running-Config

    Configuration and image files page 70 show running-config the show running-config privileged exec mode command displays the contents of the currently running config- uration file. Syntax show running-config default configuration this command has no default configuration. Command mode privileged exec...

  • Page 72: Show Startup-Config

    D-link des-3010fa/ga cli reference guide page 71 show startup-config the show startup-config privileged exec mode command displays the contents of the startup configuration file. Syntax show startup-config default configuration this command has no default configuration. Command mode privileged exec ...

  • Page 73: Interface Ethernet

    Ethernet configuration commands page 72 section 6. Ethernet configuration commands interface ethernet the interface ethernet global configuration mode command enters the interface configuration mode to configure an ethernet type interface. Syntax interface ethernet interface parameters • interface —...

  • Page 75: Shutdown

    Ethernet configuration commands page 74 shutdown the shutdown interface configuration (ethernet, port-channel) mode command disables an interface. To restart a disabled interface, use the no form of this command. Syntax shutdown no shutdown default configuration the interface is enabled. Command mod...

  • Page 76: Description

    D-link des-3010fa/ga cli reference guide page 75 description the description interface configuration (ethernet, port-channel) mode command adds a description to an inter- face. To remove the description, use the no form of this command. Syntax description string no description parameters • string — ...

  • Page 78: Duplex

    D-link des-3010fa/ga cli reference guide page 77 duplex the duplex interface configuration (ethernet) mode command configures the full/half duplex operation of a given ethernet interface when not using auto-negotiation. To restore the default configuration, use the no form of this command. Syntax du...

  • Page 79: Negotiation

    Ethernet configuration commands page 78 negotiation the negotiation interface configuration (ethernet, port-channel) mode command enables auto-negotiation oper- ation for the speed and duplex parameters of a given interface. To disable auto-negotiation, use the no form of this command. Syntax negoti...

  • Page 82: Back-Pressure

    D-link des-3010fa/ga cli reference guide page 81 back-pressure the back-pressure interface configuration (ethernet, port-channel) mode command enables back pressure on a given interface. To disable back pressure, use the no form of this command. Syntax back-pressure no back-pressure default configur...

  • Page 86

    D-link des-3010fa/ga cli reference guide page 85 ch3 enabled ch4 enabled ch5 enabled ch6 enabled.

  • Page 89

    Ethernet configuration commands page 88 ch1 not present ch2 not present ch3 not present ch4 not present ch5 not present ch6 not present.

  • Page 92

    D-link des-3010fa/ga cli reference guide page 91 the following example displays counters for ethernet port 1. The following table describes the fields shown in the display: 3 0 0 0 0 4 0 0 0 0 5 0 0 0 0 6 0 0 0 0 7 23739 0 0 0 console# show interfaces counters ethernet 1 port inoctets inucastpkts in...

  • Page 93

    Ethernet configuration commands page 92 single collision frames counted frames that are involved in a single collision, and are subsequently transmitted successfully. Late collisions number of times that a collision is detected later than one slottime into the transmission of a packet. Oversize pack...

  • Page 94

    D-link des-3010fa/ga cli reference guide page 93 port storm-control include-multicast the port storm-control include-multicast interface configuration (ethernet) mode command counts multicast packets in broadcast storm control. To disable counting multicast packets, use the no form of this command. ...

  • Page 95

    Ethernet configuration commands page 94 port storm-control broadcast enable the port storm-control broadcast enable interface configuration (ethernet) mode command enables broadcast storm control. To disable broadcast storm control, use the no form of this command. Syntax port storm-control broadcas...

  • Page 96

    D-link des-3010fa/ga cli reference guide page 95 port storm-control broadcast rate the port storm-control broadcast rate interface configuration (ethernet) mode command configures the maxi- mum broadcast rate. To return to the default configuration, use the no form of this command. Syntax port storm...

  • Page 97: Show Ports Storm-Control

    Ethernet configuration commands page 96 show ports storm-control the show ports storm-control privileged exec mode command displays the storm control configuration. Syntax show ports storm-control [interface] parameters • interface — a valid ethernet port. (full syntax: port) default configuration t...

  • Page 98: Section 7. Gvrp Commands

    D-link des-3010fa/ga cli reference guide page 97 section 7. Gvrp commands gvrp enable (global) garp vlan registration protocol (gvrp) is an industry-standard protocol designed to propagate vlan informa- tion from device to device. With gvrp, a single device is manually configured with all desired vl...

  • Page 99: Gvrp Enable (Interface)

    Gvrp commands page 98 gvrp enable (interface) the gvrp enable interface configuration (ethernet, port-channel) mode command enables gvrp on an interface. To disable gvrp on an interface, use the no form of this command. Syntax gvrp enable no gvrp enable default configuration gvrp is disabled on all ...

  • Page 100: Garp Timer

    Ethernet configuration commands page 76 speed the speed interface configuration (ethernet, port-channel) mode command configures the speed of a given ethernet interface when not using auto-negotiation. To restore the default configuration, use the no form of this command. Syntax speed {10

  • Page 101: Gvrp Vlan-Creation-Forbid

    Gvrp commands page 100 gvrp vlan-creation-forbid the gvrp vlan-creation-forbid interface configuration (ethernet, port-channel) mode command disables dynamic vlan creation or modification. To enable dynamic vlan creation or modification, use the no form of this command. Syntax gvrp vlan-creation-for...

  • Page 102: Gvrp Registration-Forbid

    D-link des-3010fa/ga cli reference guide page 101 gvrp registration-forbid the gvrp registration-forbid interface configuration (ethernet, port-channel) mode command deregisters all dynamic vlans on a port and prevents vlan creation or registration on the port. To allow dynamic registration of vlans...

  • Page 104: Show Gvrp Configuration

    D-link des-3010fa/ga cli reference guide page 103 show gvrp configuration the show gvrp configuration user exec mode command displays gvrp configuration information, including timer values, whether gvrp and dynamic vlan creation is enabled, and which ports are running gvrp. Syntax show gvrp configur...

  • Page 107: Ip Igmp Snooping (Global)

    Igmp snooping commands page 106 section 8. Igmp snooping commands ip igmp snooping (global) the ip igmp snooping global configuration mode command enables internet group management protocol (igmp) snooping. To disable igmp snooping, use the no form of this command. Syntax ip igmp snooping no ip igmp...

  • Page 108: Ip Igmp Snooping (Interface)

    D-link des-3010fa/ga cli reference guide page 107 ip igmp snooping (interface) the ip igmp snooping interface configuration (vlan) mode command enables internet group management protocol (igmp) snooping on a specific vlan. To disable igmp snooping on a vlan interface, use the no form of this command...

  • Page 109

    Igmp snooping commands page 108 ip igmp snooping host-time-out the ip igmp snooping host-time-out interface configuration (vlan) mode command configures the host-time- out. If an igmp report for a multicast group was not received for a host-time-out period from a specific port, this port is deleted ...

  • Page 110

    D-link des-3010fa/ga cli reference guide page 109 ip igmp snooping mrouter-time-out the ip igmp snooping mrouter-time-out interface configuration (vlan) mode command configures the mrouter-time-out. The ip igmp snooping mrouter-time-out interface configuration (vlan) mode command is used for setting...

  • Page 111

    Igmp snooping commands page 110 ip igmp snooping leave-time-out the ip igmp snooping leave-time-out interface configuration (vlan) mode command configures the leave- time-out. If an igmp report for a multicast group was not received for a leave-time-out period after an igmp leave was received from a...

  • Page 112

    D-link des-3010fa/ga cli reference guide page 111 show ip igmp snooping mrouter the show ip igmp snooping mrouter user exec mode command displays information on dynamically learned multicast router interfaces. Syntax show ip igmp snooping mrouter [interface vlan-id] parameters • vlan-id — vlan numbe...

  • Page 113

    Igmp snooping commands page 112 show ip igmp snooping interface the show ip igmp snooping interface user exec mode command displays igmp snooping configuration. Syntax show ip igmp snooping interface vlan-id parameters • vlan-id — vlan number. Default configuration this command has no default config...

  • Page 114: Show Ip Igmp Snooping Groups

    D-link des-3010fa/ga cli reference guide page 113 show ip igmp snooping groups the show ip igmp snooping groups user exec mode command displays multicast groups learned by igmp snooping. Syntax show ip igmp snooping groups [vlan vlan-id][address ip-multicast-address] parameters • vlan-id — vlan numb...

  • Page 116: Ip Address Dhcp

    D-link des-3010fa/ga cli reference guide page 115 ip address dhcp the ip address dhcp interface configuration (ethernet, vlan, port-channel) mode command acquires an ip address for an ethernet interface from the dynamic host configuration protocol (dhcp) server. To deconfigure an acquired ip address...

  • Page 117: Ip Default-Gateway

    Ip addressing commands page 116 ip default-gateway the ip default-gateway global configuration mode command defines a default gateway (router). To return to the default configuration, use the no form of this command. Syntax ip default-gateway ip-address no ip default-gateway parameters • ip-address ...

  • Page 120: Arp Timeout

    D-link des-3010fa/ga cli reference guide page 119 arp timeout the arp timeout global configuration mode command configures how long an entry remains in the arp cache. To return to the default configuration, use the no form of this command. Syntax arp timeout seconds no arp timeout parameters • secon...

  • Page 121: Clear Arp-Cache

    Ip addressing commands page 120 clear arp-cache the clear arp-cache privileged exec mode command deletes all dynamic entries from the arp cache. Syntax clear arp-cache default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user...

  • Page 122: Show Arp

    D-link des-3010fa/ga cli reference guide page 121 show arp the show arp privileged exec mode command displays entries in the arp table. Syntax show arp default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidelines for ...

  • Page 123: Ip Domain-Name

    Ip addressing commands page 122 ip domain-name the ip domain-name global configuration mode command defines a default domain name used by the software to complete unqualified host names (names without a dotted-decimal domain name). To remove the default domain name, use the no form of this command. ...

  • Page 124: Ip Name-Server

    D-link des-3010fa/ga cli reference guide page 123 ip name-server the ip name-server global configuration mode command defines the available name servers. To remove a name server, use the no form of this command. Syntax ip name-server server-address [server-address2 … server-address8] no ip name-serv...

  • Page 125: Ip Host

    Ip addressing commands page 124 ip host the ip host global configuration mode command defines static host name-to-address mapping in the host cache. Toremove the name-to-address mapping, use the no form of this command. Syntax ip host name address no ip host name parameters • name — name of the host...

  • Page 128: Show Hosts

    D-link des-3010fa/ga cli reference guide page 127 show hosts the show hosts privileged exec mode command displays the default domain name, a list of name server hosts, the static and the cached list of host names and addresses. Syntax show hosts [name] parameters • name — specifies the host name. (r...

  • Page 129: Section 10. Lacp Commands

    Lacp commands page 128 section 10. Lacp commands lacp system-priority the lacp system-priority global configuration mode command configures the system priority. To return to the default configuration, use the no form of this command. Syntax lacp system-priority value no lacp system-priority paramete...

  • Page 130: Lacp Port-Priority

    D-link des-3010fa/ga cli reference guide page 129 lacp port-priority the lacp port-priority interface configuration (ethernet) mode command configures physical port priority. To return to the default configuration, use the no form of this command. Syntax lacp port-priority value no lacp port-priorit...

  • Page 133

    Lacp commands page 132 distributing: false expired: false partner system priority: 0 system mac addr: 00:00:00:00:00:00 port admin key: 0 port oper key: 0 port oper number: 0 port admin priority: 0 port oper priority: 0 port oper timeout: long lacp activity: passive aggregation: aggregatable synchro...

  • Page 134: Show Lacp Port-Channel

    D-link des-3010fa/ga cli reference guide page 133 show lacp port-channel the show lacp port-channel privileged exec mode command displays lacp information for a port-channel. Syntax show lacp port-channel [port_channel_number] parameters • port_channel_number — validport-channel number. Default conf...

  • Page 136: Speed

    D-link des-3010fa/ga cli reference guide page 135 speed the speed line configuration mode command sets the line baud rate. To return to the default configuration, use the no form of the command. Syntax speed bps no speed parameters • bps—baud rate in bits per second (bps). Possible values are 2400, ...

  • Page 137: Exec-Timeout

    Line commands page 136 exec-timeout the exec-timeout line configuration mode command sets the interval that the system waits until user input is detected. To return to the default configuration, use the no form of this command. Syntax exec-timeout minutes [seconds] no exec-timeout parameters • minut...

  • Page 138: History

    D-link des-3010fa/ga cli reference guide page 137 history the history line configuration mode command enables the command history function. To disable the command history function, use the no form of this command. Syntax history no history default configuration the command history function is enable...

  • Page 139: History Size

    Line commands page 138 history size the history size line configuration mode command configures the command history buffer size for a particular line. To reset the command history buffer size to the default configuration, use the no form of this command. Syntax history size number-of-commands no his...

  • Page 140: Terminal History

    D-link des-3010fa/ga cli reference guide page 139 terminal history the terminal history user exec command enables the command history function for the current terminal ses- sion. To disable the command history function, use the no form of this command. Syntax terminal history no terminal history def...

  • Page 141: Terminal History Size

    Line commands page 140 terminal history size the terminal history size user exec command configures the command history buffer size for the current termi- nal session. To reset the command history buffer size to the default setting, use the no form of this command.. Syntax terminal history size numb...

  • Page 143: Section 12. Management Acl

    Management acl page 142 section 12. Management acl management access-list the management access-list globalconfiguration mode command configures a management access list and enters the management access-list configuration command mode. To delete an access list, use the no form of this command. Synta...

  • Page 144

    D-link des-3010fa/ga cli reference guide page 143 the following example creates a management access list called mlist, configures all interfaces to be management interfaces except ethernet interfaces 1 and 6 and makes the new access list the active list. Console(config)# management access-list mlist...

  • Page 148: Show Management Access-List

    D-link des-3010fa/ga cli reference guide page 147 show management access-list the show management access-list privileged exec mode command displays management access-lists. Syntax show management access-list [name] parameters • name — specifies the name of a management access list. (range: 1 - 32 ch...

  • Page 149: Show Management Access-Class

    Management acl page 148 show management access-class the show management access-class privileged exec mode command displays the active management access list. Syntax show management access-class default configuration this command has no default configuration. Command mode privileged exec mode user g...

  • Page 150: Test Copper-Port Tdr

    D-link des-3010fa/ga cli reference guide page 149 section 13. Phy diagnostics commands test copper-port tdr the test copper-port tdr privileged exec mode command uses time domain reflectometry (tdr) technology to diagnose the quality and characteristics of a copper cable attached to a port. Syntax t...

  • Page 151: Show Copper-Ports Tdr

    Phy diagnostics commands page 150 show copper-ports tdr the show copper-ports tdr user exec mode command displays information on the last time domain reflecto- metry (tdr) test performed on copper ports. Syntax show copper-ports tdr [interface] parameters • interface — a valid ethernet port. (full s...

  • Page 152

    D-link des-3010fa/ga cli reference guide page 151 show copper-ports cable-length the show copper-ports cable-length user exec mode command displays the estimated copper cable length attached to a port. Syntax show copper-ports cable-length [interface] parameters • interface — a valid ethernet port. ...

  • Page 153

    Phy diagnostics commands page 152 show fiber-ports optical-transceiver the show fiber-ports optical-transceiver privileged exec command displays the optical transceiver diagnos- tics. Syntax show fiber-ports optical-transceiver [interface] [detailed] parameters • interface — a valid ethernet port. (...

  • Page 154: Interface Port-Channel

    D-link des-3010fa/ga cli reference guide page 153 section 14. Port channel commands interface port-channel the interface port-channel global configuration mode command enters the interface configuration mode to con- figure a specific port-channel. Syntax interface port-channel port-channel-number pa...

  • Page 157: Show Interfaces Port-Channel

    Port channel commands page 156 show interfaces port-channel the show interfaces port-channel privileged exec mode command displays port-channel information. Syntax show interfaces port-channel [port-channel-number] parameters • port-channel-number — valid port-channel number. Default configuration t...

  • Page 159: Port Monitor Vlan-Tagging

    Port monitor commands page 158 port monitor vlan-tagging the port monitor interface configuration (ethernet) mode command transmits tagged ingress mirrored packets. To transmit untagged ingress mirrored packets, use the no form of this command. Syntax port monitor vlan-tagging no port monitor vlan-t...

  • Page 160: Show Ports Monitor

    D-link des-3010fa/ga cli reference guide page 159 show ports monitor the show ports monitor user execmode command displays the port monitoring status. Syntax show ports monitor default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no u...

  • Page 161: Section 16. Qos Commands

    Qos commands page 160 section 16. Qos commands qos the qos global configuration mode command enables quality of service (qos) on the device. To disable qos on the device, use the no form of this command. Syntax qos no qos default configuration qos is disabled on the device. Command mode global confi...

  • Page 162: Show Qos

    D-link des-3010fa/ga cli reference guide page 161 show qos the show qos user exec mode command displays quality of service (qos) for the device. Syntax show qos default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guidelines f...

  • Page 163

    Qos commands page 162 priority-queue out num-of-queues the priority-queue out num-of-queues global configuration mode command configures the number of expedite queues. To return to the default configuration, use the no form of this command. Syntax priority-queue out num-of-queues number-of-queues no...

  • Page 164

    D-link des-3010fa/ga cli reference guide page 163 rate-limit interface configuration the rate-limit interface configuration command limits the rate of the incoming traffic. The no form of this com- mand is used to disable rate limit. Syntax rate-limit rate no rate-limit parameters • kbps maximum of ...

  • Page 166

    D-link des-3010fa/ga cli reference guide page 165 switch> show qos interface 7 rate-limit port rate-limit [kbps] ----- ------------------ 7 100 3 2 4 3 5 3 6 4 7 4.

  • Page 167: Traffic-Shape

    Qos commands page 166 traffic-shape set shaper on egress port/queue. Use no form in order to disable the shaper. Traffic-shape { committed-rate } [queue-id] no traffic-shape [queue-id] syntax committed-rate –the average traffic rate (cir) in bits per second(bps). Queue-id – [optional] assign shaper ...

  • Page 168: Wrr-Queue Cos-Map

    D-link des-3010fa/ga cli reference guide page 167 wrr-queue cos-map the wrr-queue cos-map global configuration mode command maps class of service (cos) values to a specific egress queue. To return to the default configuration, use the no form of this command. Syntax wrr-queue cos-map queue-id cos1.....

  • Page 169: Qos Map Dscp-Queue

    Qos commands page 168 qos map dscp-queue the qos map dscp-queue global configuration mode command modifies the dscp to cos map. To return to the default map, use the no form of this command. Syntax qos map dscp-queue dscp-list to queue-id no qos map dscp-queue [dscp-list] parameters • dscp-list — sp...

  • Page 171: Qos Trust (Interface)

    Qos commands page 170 qos trust (interface) the qos trust interface configuration (ethernet, port-channel) mode command enables each port trust state while the system is in the basic qos mode. To disable the trust state on each port, use the no form of this command. Syntax qos trust no qos trust def...

  • Page 172: Qos Cos

    D-link des-3010fa/ga cli reference guide page 171 qos cos the qos cos interface configuration (ethernet, port-channel) mode command defines the default cos value of a port. To return to the default configuration, use the no form of this command. Syntax qos cos default-cos no qos cos parameters • def...

  • Page 173: Show Qos Map

    Qos commands page 172 show qos map the show qos map user exec mode command displays all qos maps. Syntax show qos map [dscp-queue] parameters • dscp-queue — indicates the dscp to queue map. Default configuration this command has no default configuration. Command mode user exec mode user guidelines t...

  • Page 175

    Radius commands page 174 example the following example specifies a radius server host with ip address 192.168.10.1, authentication request port number 20 and a 20-second timeout period. Console(config)# radius-server host 192.168.10.1 auth-port 20 timeout 20

  • Page 176: Radius-Server Key

    D-link des-3010fa/ga cli reference guide page 175 radius-server key the radius-server key global configuration mode command sets the authentication and encryption key for all radius communications between the device and the radius daemon. To return to the default configuration, use the no form of th...

  • Page 177: Radius-Server Retransmit

    Radius commands page 176 radius-server retransmit the radius-server retransmit global configuration mode command specifies the number of times the software searches the list of radius server hosts. To reset the default configuration, use the no form of this command. Syntax radius-server retransmit r...

  • Page 178: Radius-Server Source-Ip

    D-link des-3010fa/ga cli reference guide page 177 radius-server source-ip the radius-server source-ip global configuration mode command specifies the source ip address used for communication with radius servers. To return to the default configuration, use the no form of this command. Syntax radius-s...

  • Page 179: Radius-Server Timeout

    Radius commands page 178 radius-server timeout the radius-server timeout global configuration mode command sets the interval during which the device waits for a server host to reply. To return to the default configuration, use the no form of this command. Syntax radius-server timeout timeout no radi...

  • Page 180: Radius-Server Deadtime

    D-link des-3010fa/ga cli reference guide page 179 radius-server deadtime the radius-server deadtime global configuration mode command improves radius response time when serv- ers are unavailable. The command is used to cause the unavailable servers to be skipped. To return to the default configurati...

  • Page 181: Show Radius-Servers

    Radius commands page 180 show radius-servers the show radius-servers privileged exec mode command displays the radius server settings. Syntax show radius-servers default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guide...

  • Page 183

    Rmon commands page 182 the following table describes significant fields shown above: f i e l d d e s c r i p t i o n octets the total number of octets of data (including those in bad packets) received on the net- work (excluding framing bits but including fcs octets). Packets the total number of pac...

  • Page 184: Rmon Collection History

    D-link des-3010fa/ga cli reference guide page 183 rmon collection history the rmon collection history interface configuration (ethernet, port-channel) mode command enables a remote monitoring (rmon) mib history statistics group on an interface. To remove a specified rmon history statistics group, us...

  • Page 187

    Rmon commands page 186 the following table describes significant fields shown above: maximum table size: 500 (800 after reset) time crc align undersize oversize fragments jabbers ---------- --------- --------- -------- --------- ------- jan 18 2002 21:57:00 1 1 0 49 0 jan 18 2002 21:57:30 1 1 0 27 0...

  • Page 188

    D-link des-3010fa/ga cli reference guide page 187 fragments the total number of packets received during this sampling interval that were less than 64 octets in length (excluding framing bits but including fcs octets) had either a bad frame check sequence (fcs) with an integral number of octets (fcs ...

  • Page 189: Rmon Alarm

    Rmon commands page 188 rmon alarm the rmon alarm global configuration mode command configures alarm conditions. To remove an alarm, use the no form of this command. Syntax rmon alarm index variable interval rthreshold fthreshold revent fevent [type type] [startup direction] [owner name] no rmon alar...

  • Page 190

    D-link des-3010fa/ga cli reference guide page 189 example the following example configures the following alarm conditions: • alarm index — 1000 • sample interval — 360000 seconds • rising threshold — 1000000 • falling threshold — 1000000 • rising threshold event index — 10 • falling threshold event ...

  • Page 191: Show Rmon Alarm

    Rmon commands page 190 show rmon alarm the show rmon alarm user exec mode command displays alarm configuration. Syntax show rmon alarm number parameters • number — specifies the alarm index. (range: 1 - 65535) default configuration this command has no default configuration. Command mode user exec mo...

  • Page 192

    D-link des-3010fa/ga cli reference guide page 191 interval the interval in seconds over which the data is sampled and compared with the rising and falling thresholds. Sample type the method of sampling the variable and calculating the value compared against the thresholds. If the value is absolute, ...

  • Page 193: Rmon Event

    Rmon commands page 192 rmon event the rmon event global configuration mode command configures an event. To remove an event, use the no form of this command. Syntax rmon event index type [community text][description text] [owner name] no rmon event index parameters • index — specifies the event index...

  • Page 194: Show Rmon Events

    D-link des-3010fa/ga cli reference guide page 193 show rmon events the show rmon events user exec mode command displays the rmon event table. Syntax show rmon events default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guideli...

  • Page 195: Show Rmon Log

    Rmon commands page 194 show rmon log the show rmon log user exec mode command displays the rmon log table. Syntax show rmon log [event] parameters • event — specifies the event index. (range: 0 - 65535) default configuration this command has no default configuration. Command mode user exec mode user...

  • Page 196

    D-link des-3010fa/ga cli reference guide page 195 the following table describes the significant fields shown in the display: f i e l d d e s c r i p t i o n event an index that uniquely identifies the event. Description a comment describing this event. Time the time this entry was created..

  • Page 198: Section 19. Snmp Commands

    D-link des-3010fa/ga cli reference guide page 197 section 19. Snmp commands snmp-server community the snmp-server community global configuration mode command configures the community access string to permit access to the snmp protocol. To remove the specified community string, use the no form of thi...

  • Page 199

    Snmp commands page 198 examples the following example defines community access string public to permit administrative access to snmp protocol at an administrative station with ip address 192.168.1.20. Console(config)# snmp-server community public su 192.168.1.20

  • Page 200: Snmp-Server View

    D-link des-3010fa/ga cli reference guide page 199 snmp-server view the snmp-server view global configuration mode command creates or updates a simple network management protocol (snmp) server view entry. To remove a specified snmp server view entry, use the no form of this com- mand. Syntax snmp-ser...

  • Page 201: Snmp-Server Group

    Snmp commands page 200 snmp-server group the snmp-server group global configuration mode command configures a new simple management protocol (snmp) group or a table that maps snmp users to snmp views. To remove a specified snmp group, use the no form of this command. Syntax snmp-server group groupna...

  • Page 203

    Snmp commands page 202 examples the following example configures an snmpv3 user john in group user-group. Console(config)# snmp-server user john user-group.

  • Page 204: Snmp-Server Engineid Local

    D-link des-3010fa/ga cli reference guide page 203 snmp-server engineid local the snmp-server engineid local global configuration mode command specifies the simple network manage- ment protocol (snmp) engineid on the local device. To remove the configured engine id, use the no form of this command. S...

  • Page 205

    Snmp commands page 204 examples the following example enables snmpv3 on the device and sets the local engine id of the device to the default value. Console(config) # snmp-server engineid local default.

  • Page 206: Snmp-Server Enable Traps

    D-link des-3010fa/ga cli reference guide page 205 snmp-server enable traps the snmp-server enable traps global configuration mode command enables the device to send snmp traps. To disable snmp traps, use the no form of the command. Syntax snmp-server enable traps no snmp-server enable traps default ...

  • Page 207: Snmp-Server Filter

    Snmp commands page 206 snmp-server filter the snmp-server filter global configuration mode command creates or updates a simple network management protocol (snmp) server filter entry. To remove the specified snmp server filter entry, use the no form of this com- mand. Syntax snmp-server filter filter...

  • Page 208: Snmp-Server Host

    D-link des-3010fa/ga cli reference guide page 207 snmp-server host the snmp-server host global configuration mode command specifies the recipient of simple network manage- ment protocol version 1 or version 2 notifications. To remove the specified host, use the no form of this command. Syntax snmp-s...

  • Page 210

    D-link des-3010fa/ga cli reference guide page 209 snmp-server trap authentication the snmp-server trap authentication global configuration mode command enables the device to send snmp traps when authentication fails. To disable snmp failed authentication traps, use the no form of this command. Synta...

  • Page 211: Snmp-Server Contact

    Snmp commands page 210 snmp-server contact the snmp-server contact global configuration mode command configures the system contact (syscontact) string. To remove system contact information, use the no form of the command. Syntax snmp-server contact text no snmp-server contact parameters • text — spe...

  • Page 212: Snmp-Server Location

    D-link des-3010fa/ga cli reference guide page 211 snmp-server location the snmp-server location global configuration mode command configures the system location string. To remove the location string, use the no form of this command. Syntax snmp-server location text no snmp-server location parameters...

  • Page 213: Snmp-Server Set

    Snmp commands page 212 snmp-server set the snmp-server set global configuration mode command defines the snmp mib value. Syntax snmp-server set variable-name name1 value1 [ name2 value2 …] parameters • variable-name — mib variable name. • name value — list of name and value pairs. In the case of sca...

  • Page 214: Show Snmp

    D-link des-3010fa/ga cli reference guide page 213 show snmp the show snmp privileged exec mode command displays the snmp status. Syntax show snmp default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidelines for this c...

  • Page 215

    Snmp commands page 214 the following table describes significant fields shown above. Version 3 notifications target address type username security level udp port filter name to sec retries -------------- ----- --------- ------- ---- ------ --- ------- 192.122.173.42 inform bob priv 162 15 3 system c...

  • Page 216: Show Snmp Engineid

    D-link des-3010fa/ga cli reference guide page 215 show snmp engineid the show snmp engineid privileged exec mode command displays the id of the local simple network man- agement protocol (snmp) engine. Syntax show snmp engineid default configuration this command has no default configuration. Command...

  • Page 217: Show Snmp Views

    Snmp commands page 216 show snmp views the show snmp views privileged exec mode command displays the configuration of views. Syntax show snmp views [viewname] parameters • viewname — specifies the name of the view. (range: 1-30) default configuration this command has no default configuration. Comman...

  • Page 218: Show Snmp Groups

    D-link des-3010fa/ga cli reference guide page 217 show snmp groups the show snmp groups privileged exec mode command displays the configuration of groups. Syntax show snmp groups [groupname] parameters • groupname—specifies the name of the group. (range: 1-30) default configuration this command has ...

  • Page 219

    Snmp commands page 218 write name of the view that enables entering data and managing the contents of the agent. Notify name of the view that enables specifying an inform or a trap..

  • Page 220: Show Snmp Filters

    D-link des-3010fa/ga cli reference guide page 219 show snmp filters the show snmp filters privileged exec mode command displays the configuration of filters. Syntax show snmp filters [filtername] parameters • filtername—specifies the name of the filter. (range: 1-30) default configuration this comma...

  • Page 221: Show Snmp Users

    Snmp commands page 220 show snmp users the show snmp users privileged exec mode command displays the configuration of users. Syntax show snmp users [username] parameters • username—specifies the name of the user. (range: 1-30) default configuration this command has no default configuration. Command ...

  • Page 222: Spanning-Tree

    D-link des-3010fa/ga cli reference guide page 221 section 20. Spanning-tree commands spanning-tree the spanning-tree global configuration mode command enables spanning-tree functionality. To disable span- ning-tree functionality, use the no form of this command. Syntax spanning-tree no spanning-tree...

  • Page 224: Spanning-Tree Forward-Time

    D-link des-3010fa/ga cli reference guide page 223 spanning-tree forward-time the spanning-tree forward-time global configuration mode command configures the spanning-tree bridge for- ward time, which is the amount of time a port remains in the listening and learning states before entering the for- w...

  • Page 225: Spanning-Tree Hello-Time

    Spanning-tree commands page 224 spanning-tree hello-time the spanning-tree hello-time global configuration mode command configures the spanning tree bridge hello time, which is how often the device broadcasts hello messages to other devices.To return to the default configura- tion, use the no form o...

  • Page 226: Spanning-Tree Max-Age

    D-link des-3010fa/ga cli reference guide page 225 spanning-tree max-age the spanning-tree max-age global configuration mode command configures the spanning tree bridge maximum age. To return to the default configuration, use the no form of this command. Syntax spanning-tree max-age seconds no spanni...

  • Page 227: Spanning-Tree Priority

    Spanning-tree commands page 226 spanning-tree priority the spanning-tree priority global configuration mode command configures the spanning tree priority of the device. The priority value is used to determine which bridge is elected as the root bridge. To return to the default configuration, use the...

  • Page 228: Spanning-Tree Disable

    D-link des-3010fa/ga cli reference guide page 227 spanning-tree disable the spanning-tree disable interface configuration mode command disables spanning tree on a specific port. To enable spanning tree on a port, use the no form of this command. Syntax spanning-tree disable no spanning-tree disable ...

  • Page 229: Spanning-Tree Cost

    Spanning-tree commands page 228 spanning-tree cost the spanning-tree cost interface configuration mode command configures the spanning tree path cost for a port. To return to the default configuration, use the no form of this command. Syntax spanning-tree cost cost no spanning-tree cost parameters •...

  • Page 230: Spanning-Tree Port-Priority

    D-link des-3010fa/ga cli reference guide page 229 spanning-tree port-priority the spanning-tree port-priority interface configuration mode command configures port priority. To return to the default configuration, use the no form of this command. Syntax spanning-tree port-priority priority no spannin...

  • Page 231: Spanning-Tree Portfast

    Spanning-tree commands page 230 spanning-tree portfast the spanning-tree portfast interface configuration mode command enables portfast mode. In portfast mode, the interface is immediately put into the forwarding state upon linkup without waiting for the standard forward time delay. To disable portf...

  • Page 232: Spanning-Tree Link-Type

    D-link des-3010fa/ga cli reference guide page 231 spanning-tree link-type the spanning-tree link-type interface configuration mode command overrides the default link-type setting deter- mined by the duplex mode of the port and enables rapid spanning tree protocol (rstp) transitions to the for- wardi...

  • Page 234: Spanning-Tree Bpdu

    D-link des-3010fa/ga cli reference guide page 233 spanning-tree bpdu the spanning-tree bpdu global configuration mode command defines bpdu handling when the spanning tree is disabled globally or on a single interface. To return to the default configuration, use the no form of this command. Syntax sp...

  • Page 235

    Spanning-tree commands page 234 clear spanning-tree detected-protocols the clear spanning-tree detected-protocols privileged exec mode command restarts the protocol migration process (forces renegotiation with neighboring devices) on all interfaces or on a specified interface. Syntax clear spanning-...

  • Page 236: Spanning-Tree Guard Root

    D-link des-3010fa/ga cli reference guide page 235 spanning-tree guard root the spanning-tree guard root interface configuration command enables root guard on all spanning tree instances on that interface. Root guard restricts the interface to be the root port for the switch. To disable root guard on...

  • Page 237: Spanning-Tree Mst Priority

    Spanning-tree commands page 236 spanning-tree mst priority the spanning-tree mst priority global configuration mode command configures the device priority for the spec- ified spanning-tree instance. To return to the default configuration, use the no form of this command. Syntax spanning-tree mst ins...

  • Page 238: Spanning-Tree Mst Max-Hops

    D-link des-3010fa/ga cli reference guide page 237 spanning-tree mst max-hops the spanning-tree mst priority global configuration mode command configures the number of hops in an mst region before the bdpu is discarded and the port information is aged out. To return to the default configuration, use ...

  • Page 239

    Spanning-tree commands page 238 spanning-tree mst port-priority the spanning-tree mst port-priority interface configuration mode command configures port priority for the specified mst instance. To return to the default configuration, use the no form of this command. Syntax spanning-tree mst instance...

  • Page 240: Spanning-Tree Mst Cost

    D-link des-3010fa/ga cli reference guide page 239 spanning-tree mst cost the spanning-tree mst cost interface configuration mode command configures the path cost for multiple span- ning tree (mst) calculations. If a loop occurs, the spanning tree considers path cost when selecting an interface to pu...

  • Page 241

    Spanning-tree commands page 240 spanning-tree mst configuration the spanning-tree mst configuration global configuration mode command enables configuring an mst region by entering the multiple spanning tree (mst) mode. Syntax spanning-tree mst configuration default configuration this command has no ...

  • Page 243: Name (Mst)

    Spanning-tree commands page 242 name (mst) the name mst configuration mode command defines the configuration name. To return to the default setting, use the no form of this command. Syntax name string parameters • string—mst configuration name. Case-sensitive (range: 1-32 characters). Default config...

  • Page 244: Revision (Mst)

    D-link des-3010fa/ga cli reference guide page 243 revision (mst) the revision mst configuration command defines the configuration revision number. To return to the default con- figuration, use the no form of this command. Syntax revision value no revision parameters • value—configuration revision nu...

  • Page 246: Exit (Mst)

    D-link des-3010fa/ga cli reference guide page 245 exit (mst) the exit mst configuration mode command exits the mst configuration mode and applies all configuration changes. Syntax exit default configuration this command has no default configuration. Command mode mst configuration mode user guideline...

  • Page 247: Abort (Mst)

    Spanning-tree commands page 246 abort (mst) the abort mst configuration mode command exits the mst configuration mode without applying the configura- tion changes. Syntax abort default configuration this command has no default configuration. Command mode mst configuration mode user guidelines there ...

  • Page 249

    Spanning-tree commands page 248 console# show spanning-tree spanning tree disabled (bpdu flooding) mode stp default port cost method: short root id priority 32768 address 00:19:28:37:46:00 this switch is the root hello time 2 sec max age 20 sec forward delay 15 sec number of topology changes 0 last ...

  • Page 250: Section 21. Syslog Commands

    D-link des-3010fa/ga cli reference guide page 249 section 21. Syslog commands logging on the logging on global configuration mode command controls error message logging. This command sends debug or error messages to a logging process, which logs messages to designated locations asynchronously to the...

  • Page 252: Logging Console

    D-link des-3010fa/ga cli reference guide page 251 logging console the logging console global configuration mode command limits messages logged to the console based on severity. To disable logging to the console, use the no form of this command. Syntax logging console level no logging console paramet...

  • Page 253: Logging Buffered

    Syslog commands page 252 logging buffered the logging buffered global configuration mode command limits syslog messages displayed from an internal buffer based on severity. To cancel using the buffer, use the no form of this command. Syntax logging buffered level no logging buffered parameters • lev...

  • Page 254: Logging Buffered Size

    D-link des-3010fa/ga cli reference guide page 253 logging buffered size the logging buffered size global configuration mode command changes the number of syslog messages stored in the internal buffer. To return to the default configuration, use the no form of this command. Syntax logging buffered si...

  • Page 255: Clear Logging

    Syslog commands page 254 clear logging the clear logging privileged exec mode command clears messages from the internal logging buffer. Syntax clear logging default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidelines...

  • Page 256: Logging File

    D-link des-3010fa/ga cli reference guide page 255 logging file the logging file global configuration mode command limits syslog messages sent to the logging file based on severity. To cancel using the buffer, use the no form of this command. Syntax logging file level no logging file parameters • lev...

  • Page 257: Clear Logging File

    Syslog commands page 256 clear logging file the clear logging file privileged exec mode command clears messages from the logging file. Syntax clear logging file default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidel...

  • Page 258: Aaa Logging

    D-link des-3010fa/ga cli reference guide page 257 aaa logging the aaa logging global configuration mode command enables logging aaa login events. To disable logging aaa login events, use the no form of this command. Syntax aaa logging login no aaa logging login parameters • login — indicates logging...

  • Page 259: File-System Logging

    Syslog commands page 258 file-system logging the file-system logging global configuration mode command enables logging file system events. To disable log- ging file system events, use the no form of this command. Syntax file-system logging copy no file-system logging copy file-system logging delete-...

  • Page 260: Management Logging

    D-link des-3010fa/ga cli reference guide page 259 management logging the management logging global configuration command enables logging management access list (acl) events. To disable logging management access list events, use the no form of this command. Syntax management logging deny no managemen...

  • Page 261: Show Logging

    Syslog commands page 260 show logging the show logging privileged exec mode command displays the state of logging and the syslog messages stored in the internal buffer. Syntax show logging default configuration this command has no default configuration. Command mode privileged exec mode user guideli...

  • Page 262

    D-link des-3010fa/ga cli reference guide page 261 11-aug-2004 15:41:43: %link-3-updown: interface ethernet2, changed state to up 11-aug-2004 15:41:43: %link-3-updown: interface ethernet, changed state to up 11-aug-2004 15:41:43: %sys-5-config_i: configured from memory by console 11-aug-2004 15:41:39...

  • Page 263: Show Logging File

    Syslog commands page 262 show logging file the show logging file privileged exec mode command displays the state of logging and the syslog messages stored in the logging file. Syntax show logging file default configuration this command has no default configuration. Command mode privileged exec mode ...

  • Page 264

    D-link des-3010fa/ga cli reference guide page 263 11-aug-2004 15:41:43: %link-3-updown: interface ethernet2, changed state to up 11-aug-2004 15:41:43: %link-3-updown: interface ethernet3, changed state to up 11-aug-2004 15:41:43: %sys-5-config_i: configured from memory by console 11-aug-2004 15:41:3...

  • Page 265: Show Syslog-Servers

    Syslog commands page 264 show syslog-servers the show syslog-servers privileged exec mode command displays the settings of the syslog servers. Syntax show syslog-servers default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no us...

  • Page 267

    System management page 266 examples the following example displays pinging results: console> ping 10.1.1.1 pinging 10.1.1.1 with 64 bytes of data: 64 bytes from 10.1.1.1: icmp_seq=0. Time=11 ms 64 bytes from 10.1.1.1: icmp_seq=1. Time=8 ms 64 bytes from 10.1.1.1: icmp_seq=2. Time=8 ms 64 bytes from ...

  • Page 269

    System management page 268 examples the following example discovers the routes that packets will actually take when traveling to their destination. The following table describes significant fields shown above. The following table describes characters that may appear in the traceroute command output....

  • Page 270: Reload

    D-link des-3010fa/ga cli reference guide page 269 reload the reload privileged exec mode command reloads the operating system. Syntax reload default configuration this command has no default configuration. Command mode privileged exec mode user guidelines caution should be exercised when resetting t...

  • Page 271: Hostname

    System management page 270 hostname the hostname global configuration mode command specifies or modifies the device host name. To remove the existing host name, use the no form of the command. Syntax hostname name no hostname parameters • name — the host name. Of the device. (range: 1-158 characters...

  • Page 272: Show Users

    D-link des-3010fa/ga cli reference guide page 271 show users the show users user exec mode command displays information about the active users. Syntax show users default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guidelines ...

  • Page 273: Show System

    System management page 272 show system the show system user exec mode command displays system information. Syntax show system default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guidelines for this command. Example the follow...

  • Page 274: Show Version

    D-link des-3010fa/ga cli reference guide page 273 show version the show version user exec mode command displays system version information. Syntax show version default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guidelines fo...

  • Page 275: Show System Id

    System management page 274 show system id the show system id user exec mode command displays system id information. Syntax show system id default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guidelines for this command. Exampl...

  • Page 276: Section 23. User Interface

    D-link des-3010fa/ga cli reference guide page 275 section 23. User interface enable the enable user exec mode command enters the privileged exec mode. Syntax enable [privilege-level] parameters • privilege-level — privilege level to enter the system. (range: 1 - 15) default configuration the default...

  • Page 277: Disable

    User interface page 276 disable the disable privileged exec mode command returns to the user exec mode. Syntax disable [privilege-level] parameters • privilege-level — privilege level to enter the system. (range: 1 - 15) default configuration the default privilege level is 1. Command mode privileged...

  • Page 278: Login

    D-link des-3010fa/ga cli reference guide page 277 login the login user exec mode command changes a login username. Syntax login default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guidelines for this command. Example the foll...

  • Page 279: Configure

    User interface page 278 configure the configure privileged exec mode command enters the global configuration mode. Syntax configure default configuration this command has no default configuration. Command mode privilegedexec mode user guidelines there are no user guidelines for this command. Example...

  • Page 280: Exit (Configuration)

    D-link des-3010fa/ga cli reference guide page 279 exit (configuration) the exit command exits any configuration mode to the next highest mode in the cli mode hierarchy. Syntax exit default configuration this command has no default configuration. Command mode all configuration modes user guidelines t...

  • Page 281: Exit

    User interface page 280 exit the exit privileged/user exec mode command closes an active terminal session by logging off the device. Syntax exit default configuration this command has no default configuration. Command mode privileged and user exec modes user guidelines there are no user guidelines f...

  • Page 282: End

    D-link des-3010fa/ga cli reference guide page 281 end the end command ends the current configuration session and returns to the privileged exec mode. Syntax end default configuration this command has no default configuration. Command mode all configuration modes. User guidelines there are no user gu...

  • Page 283: Help

    User interface page 282 help the help command displays a brief description of the help system. Syntax help default configuration this command has no default configuration. Command mode all command modes user guidelines there are no user guidelines for this command. Example the following example desc...

  • Page 284: Terminal Data-Dump

    D-link des-3010fa/ga cli reference guide page 283 terminal data-dump the terminal data-dump user exec mode command enables dumping all the output of a show command with- out prompting. To disable dumping, use the no form of this command. Syntax terminal data-dump no terminal data-dump default config...

  • Page 285: Show History

    User interface page 284 show history the show history user exec mode command lists the commands entered in the current session. Syntax show history default configuration this command has no default configuration. Command mode user exec mode user guidelines the buffer includes executed and unexecuted...

  • Page 286: Show Privilege

    D-link des-3010fa/ga cli reference guide page 285 show privilege the show privilege privileged/user exec mode command displays the current privilege level. Syntax show privilege default configuration this command has no default configuration. Command mode privileged and user exec modes user guidelin...

  • Page 287: Section 24. Vlan Commands

    Vlan commands page 286 section 24. Vlan commands vlan database the vlan database global configuration mode command enters the vlan configuration mode. Syntax vlan database default configuration this command has no default configuration. Command mode global configuration mode user guidelines there ar...

  • Page 288: Vlan

    D-link des-3010fa/ga cli reference guide page 287 vlan use the vlan vlan configuration mode command to create a vlan. To delete a vlan, use the no form of this command. Syntax vlan vlan-range no vlan vlan-range parameters • vlan-range — specifies a list of vlan ids to be added. Separate nonconsecuti...

  • Page 289: Interface Vlan

    Vlan commands page 288 interface vlan the interface vlan global configuration mode command enters the interface configuration (vlan) mode. Syntax interface vlan vlan-id parameters • vlan-id — specifies an existing vlan id. Default configuration this command has no default configuration. Command mode...

  • Page 291: Name

    Vlan commands page 290 name the name interface configuration mode command adds a name to a vlan. To remove the vlan name, use the no form of this command. Syntax name string no name parameters • string — unique name to be associated with this vlan. (range: 1-32 characters) default configuration no n...

  • Page 292: Private-Vlan Primary

    D-link des-3010fa/ga cli reference guide page 291 private-vlan primary the private-vlan primary interface configuration mode command configures the primary pvlan. To return to the default configuration, use the no form of this command. Syntax private-vlan primary no private-vlan primary default conf...

  • Page 293: Private-Vlan Isolated

    Vlan commands page 292 private-vlan isolated the private-vlan isolated interface configuration mode command configures the isolated vlan of the pvlan. To return to the default configuration, use the no form of this command. Syntax private-vlan isolated vlan-id no private-vlan isolated • vlan-id — sp...

  • Page 296: Switchport Access Vlan

    D-link des-3010fa/ga cli reference guide page 295 switchport access vlan the switchport access vlan interface configuration mode command configures the vlan id when the interface is in access mode. To return to the default configuration, use the no form of this command. Syntax switchport access vlan...

  • Page 297: Switchport Private-Vlan

    Vlan commands page 296 switchport private-vlan the switchport private-vlan interface configuration command configures private-vlan port vlans. To return to the default configuration, use the no form of this command. Syntax switchport private-vlan promiscuous pvlan no switchport private-vlan promiscu...

  • Page 298: Show Vlan Private-Vlan

    D-link des-3010fa/ga cli reference guide page 297 show vlan private-vlan the show vlan private-vlan privileged exec mode command displays information about private vlans. Syntax show vlan private-vlan [primary vlan-id] • vlan-id— specifies the id of the primary vlan. Default configuration this comma...

  • Page 300: Switchport Trunk Native Vlan

    D-link des-3010fa/ga cli reference guide page 299 switchport trunk native vlan the switchport trunk native vlan interface configuration mode command defines the native vlan when the interface is in trunk mode. To return to the default configuration, use the no form of this command. Syntax switchport...

  • Page 302: Switchport General Pvid

    D-link des-3010fa/ga cli reference guide page 301 switchport general pvid the switchport general pvid interface configuration mode command configures the pvid when the interface is in general mode. To return to the default configuration, use the no form of this command. Syntax switchport general pvi...

  • Page 303

    Vlan commands page 302 switchport general ingress-filtering disable the switchport general ingress-filtering disable interface configuration mode command disables port ingress filtering. To return to the default configuration, use the no form of this command. Syntax switchport general ingress-filter...

  • Page 304

    D-link des-3010fa/ga cli reference guide page 303 switchport general acceptable-frame-type tagged-only the switchport general acceptable-frame-type tagged-only interface configuration mode command discards untagged frames at ingress. To return to the default configuration, use the no form of this co...

  • Page 306: Switchport Protected

    D-link des-3010fa/ga cli reference guide page 305 switchport protected the switchport protected interface configuration mode command overrides the fdb decision and sends all unicast, multicast and broadcast traffic to an uplink port. To return to the default configuration, use the no form of the com...

  • Page 307: Ip Internal-Usage-Vlan

    Vlan commands page 306 ip internal-usage-vlan the ip internal-usage-vlan interface configuration mode command reserves a vlan as the internal usage vlan of an interface. To return to the default configuration, use the no form of this command. Syntax ip internal-usage-vlan vlan-id no ip internal-usag...

  • Page 309: Show Vlan Internal Usage

    Vlan commands page 308 show vlan internal usage the show vlan internal usage privileged exec mode command displays a list of vlans used internally by the device. Syntax show vlan internal usage default configuration this command has no default configuration. Command mode privileged exec mode user gu...

  • Page 311

    Vlan commands page 310 static configuration: pvid: 1 (default) ingress filtering: enabled acceptable frame type: all port 1 is statically configured to: vlan name egress rule ---- ------- ----------- 1 default untagged 11 vlan011 tagged 19 ipv6 vlan untagged 72 vlan0072 untagged forbidden vlans: vla...

  • Page 312

    D-link des-3010fa/ga cli reference guide page 311 port 2 is statically confgiured to: vlan name egress rule ---- ------------ ----------- 8 vlan0072 untagged 91 ip telephony tagged forbidden vlans: vlan name ---- ---- 73 out port 7 vlan membership mode: primary vlan: 2921 community vlan: 2922 consol...

  • Page 313: Section 25. Web Server

    Web server page 312 section 25. Web server ip http server the ip http server global configuration mode command enables configuring the device from a browser. To dis- able this function, use the no form of this command. Syntax ip http server no ip http server default configuration http server is enab...

  • Page 314: Ip Https Server

    D-link des-3010fa/ga cli reference guide page 313 ip https server the ip https server global configuration mode command enables configuring the device from a browser. To dis- able this function, use the no form of this command. Syntax ip https server no ip https server default configuration https se...

  • Page 315: Ip Http Port

    Web server page 314 ip http port the ip http port global configuration mode command specifies the tcp port to be used by the web browser interface. To return to the default configuration, use the no form of this command. Syntax ip http port port-number no ip http port parameters • port-number — port...

  • Page 316: Ip Https Port

    D-link des-3010fa/ga cli reference guide page 315 ip https port the ip https port global configuration mode command specifies the tcp port to be used by the web browser interface. To return to the default configuration, use the no form of this command. Syntax ip https port port-number no ip https po...

  • Page 317: Show Ip Http

    Web server page 316 show ip http the show ip http privileged exec mode command displays the http server configuration. Syntax show ip http default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidelines for this command....

  • Page 318: Section 26. 802.1X Commands

    D-link des-3010fa/ga cli reference guide page 317 section 26. 802.1x commands aaa authentication dot1x the aaa authentication dot1x global configuration mode command specifies one or more authentication, autho- rization, and accounting (aaa) methods for use on interfaces running ieee 802.1x. To retu...

  • Page 319: Dot1X System-Auth-Control

    802.1x commands page 318 dot1x system-auth-control the dot1x system-auth-control global configuration mode command enables 802.1x globally. To return to the default configuration, use the no form of this command. Syntax dot1x system-auth-control no dot1x system-auth-control default configuration 802...

  • Page 320: Dot1X Port-Control

    D-link des-3010fa/ga cli reference guide page 319 dot1x port-control the dot1x port-control interface configuration mode command enables manually controlling the authorization state of the port. To return to the default configuration, use the no form of this command. Syntax dot1x port-control {auto ...

  • Page 321: Dot1X Re-Authentication

    802.1x commands page 320 dot1x re-authentication the dot1x re-authentication interface configuration mode command enables periodic re-authentication of the client. To return to the default configuration, use the no form of this command. Syntax dot1x re-authentication no dot1x re-authentication defau...

  • Page 322: Dot1X Timeout Re-Authperiod

    D-link des-3010fa/ga cli reference guide page 321 dot1x timeout re-authperiod the dot1x timeout re-authperiod interface configuration mode command sets the number of seconds between re-authentication attempts. To return to the default configuration, use the no form of this command. Syntax dot1x time...

  • Page 323: Dot1X Re-Authenticate

    802.1x commands page 322 dot1x re-authenticate the dot1x re-authenticate privileged exec mode command manually initiates a re-authentication of all 802.1x- enabled ports or the specified 802.1x-enabled port. Syntax dot1x re-authenticate [ethernet interface] parameters • interface — valid ethernet po...

  • Page 324: Dot1X Timeout Quiet-Period

    D-link des-3010fa/ga cli reference guide page 323 dot1x timeout quiet-period the dot1x timeout quiet-period interface configuration mode command sets the number of seconds that the device remains in the quiet state following a failed authentication exchange (for example, the client provided an inval...

  • Page 325: Dot1X Timeout Tx-Period

    802.1x commands page 324 dot1x timeout tx-period the dot1x timeout tx-period interface configuration mode command sets the number of seconds that the device waits for a response to an extensible authentication protocol (eap)-request/identity frame from the client before resending the request. To ret...

  • Page 326: Dot1X Max-Req

    D-link des-3010fa/ga cli reference guide page 325 dot1x max-req the dot1x max-req interface configuration mode command sets the maximum number of times that the device sends an extensible authentication protocol (eap)-request/identity frame (assuming that no response is received) to the client, befo...

  • Page 327: Dot1X Timeout Supp-Timeout

    802.1x commands page 326 dot1x timeout supp-timeout the dot1x timeout supp-timeout interface configuration mode command sets the time for the retransmission of an extensible authentication protocol (eap)-request frame to the client. To return to the default configuration, use the no form of this com...

  • Page 328: Dot1X Timeout Server-Timeout

    D-link des-3010fa/ga cli reference guide page 327 dot1x timeout server-timeout the dot1x timeout server-timeout interface configuration mode command sets the time that the device waits for a response from the authentication server. To return to the default configuration, use the no form of this comm...

  • Page 329: Show Dot1X

    802.1x commands page 328 show dot1x the show dot1x privileged exec mode command displays the 802.1x status of the device or specified interface. Syntax show dot1x [ethernet interface] parameters • interface — valid ethernet port. (full syntax: port) default configuration this command has no default ...

  • Page 330

    D-link des-3010fa/ga cli reference guide page 329 the following table describes significant fields shown above: port admin mode oper mode reauth control reauth period username ---- ---------- --------- ------- ------ -------- 3 auto unauthorized ena 3600 clark quiet period: 60 seconds tx period:30 s...

  • Page 331

    802.1x commands page 330 max req the maximum number of times that the device sends an extensible authentica- tion protocol (eap)-request frame (assuming that no response is received) to the client before restarting the authentication process. Supplicant timeout time in seconds the switch waits for a...

  • Page 332: Show Dot1X Users

    D-link des-3010fa/ga cli reference guide page 331 show dot1x users the show dot1x users privileged exec mode command displays active 802.1x authenticated users for the device. Syntax show dot1x users [username username] parameters • username — supplicantusername (range: 1-160 characters) default con...

  • Page 333

    802.1x commands page 332 the following table describes significant fields shown above: field description port the port number. Username the username representing the identity of the supplicant. Session time the period of time the supplicant is connected to the system. Authentication method authentic...

  • Page 334: Show Dot1X Statistics

    D-link des-3010fa/ga cli reference guide page 333 show dot1x statistics the show dot1x statistics privileged exec mode command displays 802.1x statistics for the specified interface. Syntax show dot1x statistics ethernet interface parameters • interface — valid ethernet port. (full syntax: port) def...

  • Page 335

    802.1x commands page 334 the following table describes the significant fields shown in the display: field description eapolframesrx the number of valid eapol frames of any type that have been received by this authenticator. Eapolframestx the number of eapol frames of any type that have been transmit...

  • Page 336: Advanced Features

    D-link des-3010fa/ga cli reference guide page 335 advanced features dot1x auth-not-req the dot1x auth-not-req interface configuration mode command enables unauthorized devices access to the vlan. To disable access to the vlan, use the no form of this command. Syntax dot1x auth-not-req no dot1x auth-...

  • Page 337: Dot1X Multiple-Hosts

    802.1x commands page 336 dot1x multiple-hosts the dot1x multiple-hosts interface configuration mode command enables multiple hosts (clients) on an 802.1x- authorized port, where the authorization state of the port is set to auto. To return to the default configuration, use the no form of this comman...

  • Page 338: Dot1X Single-Host-Violation

    D-link des-3010fa/ga cli reference guide page 337 dot1x single-host-violation the dot1x single-host-violation interface configuration mode command configures the action to be taken, when a station whose mac address is not the supplicant mac address, attempts to access the interface. Use the no form ...

  • Page 339: Dot1X Guest-Vlan

    802.1x commands page 338 dot1x guest-vlan the dot1x guest-vlan interface configuration mode command defines a guest vlan. To return to the default configuration, use the no form of this command. Syntax dot1x guest-vlan no dot1x guest-vlan default configuration no vlan is defined as a guest vlan. Com...

  • Page 340: Dot1X Guest-Vlan Enable

    D-link des-3010fa/ga cli reference guide page 339 dot1x guest-vlan enable the dot1x vlans guest-vlan enable interface configuration mode command enables unauthorized users on the interface access to the guest vlan. To disable access, use the no form of this command syntax dot1x guest-vlan enable no ...

  • Page 341: Show Dot1X Advanced

    802.1x commands page 340 show dot1x advanced the show dot1x advanced privileged exec mode command displays 802.1x advanced features for the device or specified interface. Syntax show dot1x advanced [ethernet interface] parameters • interface — valid ethernet port. (full syntax: port) default configu...

  • Page 342

    D-link des-3010fa/ga cli reference guide page 341 trap frequency: 100 status: single-host locked violations since last trap: 9.

  • Page 343: Troubleshooting

    Copyright © 2005 confidential april 22, 2005 document classification: proprietary information page 342 troubleshooting this section describes problems that may arise when installing the and how to resolve these issue. This section includes the following topics: • problem management — provides inform...

  • Page 344

    D-link des-3010fa/ga cli reference guide confidential copyright © 2005 page 343 document classification: proprietary information april 22, 2005 p r o b l e m s p o s s i b l e c a u s e s o l u t i o n cannot connect to manage- ment using rs-232 serial connection be sure the terminal emulator progra...

  • Page 345

    Copyright © 2005 confidential april 22, 2005 document classification: proprietary information page 344 no connection and the port led is off incorrect ethernet cable, e.G., crossed rather than straight cable, or vice versa, split pair (incorrect twisting of pairs) fiber optical cable connec- tion is...

  • Page 346

    D-link des-3010fa/ga cli reference guide confidential copyright © 2005 page 345 document classification: proprietary information april 22, 2005 add and edit pages do not open. A pop-up blocker is enabled. Disable pop-up blockers. Lost password the password recovery procedure enables the user to set ...

  • Page 347: Product Registration

    Copyright © 2005 confidential april 22, 2005 document classification: proprietary information page 346 product registration d-link products can be registered online at http://support.Dlink.Com/register/ . Product registration is entirely voluntary and failure to complete or return this form will not...

  • Page 348

    D-link des-3010fa/ga user guide page 347 international offices u.S.A 17595 mt. Herrmann street fountain valley, ca. 92708 tel: 714-885-6000 fax 866-743-4905 url: www.Dlink.Com canada 2180 winston park drive oakville, ontario, l6h 5w1 canada tel: 1-905-8295033 fax: 1-905-8295223 url: www.Dlink.Ca eur...