1. DL manuals
  2. D-Link
  3. Switch
  4. DES-3010FA
  5. Cli Manual

D-Link DES-3010FA Cli Manual - Section 12. Management Acl

Other manuals for DES-3010FA: Web User Manual, Cli Manual
Manual is about: Layer 2 Switch, 8 Port 10/100 802.3af PoE Managed Switch Plus (1)Gigabit Copper and (1)SFP Interface

Summary of DES-3010FA

  • Page 2: Table of Contents

    D-link des-3010fa/ga/pa cli reference guide page 1 table of contents section 1. Using the cli..................................................................................................... 10 1.1 cli command modes....................................................................................

  • Page 3

    Table of contents page 2 show ports security ............................................................................................................... 45 section 4. Clock.................................................................................................................. 47 clock ...

  • Page 4

    D-link des-3010fa/ga/pa cli reference guide page 3 show interfaces configuration ............................................................................................... 86 show interfaces status ....................................................................................................

  • Page 5

    Table of contents page 4 clear host ............................................................................................................................ 126 clear host dhcp.................................................................................................................... 127...

  • Page 6

    D-link des-3010fa/ga/pa cli reference guide page 5 section 15. Port monitor commands.................................................................................. 158 port monitor........................................................................................................................

  • Page 7

    Table of contents page 6 power inline usage-threshold .............................................................................................. 195 power inline traps enable .................................................................................................... 196 show power inlin...

  • Page 8

    D-link des-3010fa/ga/pa cli reference guide page 7 spanning-tree max-age ....................................................................................................... 243 spanning-tree priority ...................................................................................................

  • Page 9

    Table of contents page 8 disable................................................................................................................................. 284 login ...................................................................................................................................

  • Page 10

    D-link des-3010fa/ga/pa cli reference guide page 9 crypto certificate generate................................................................................................... 323 crypto certificate import................................................................................................

  • Page 11: Section 1. Using The Cli

    Using the cli cli command modes page 10 section 1. Using the cli this chapter describes how to start using the cli and describes implemented command editing features to assist in using the cli. 1.1 cli command modes 1.1.1 introduction to assist in configuring the device, the command line interface (...

  • Page 12

    D-link des-3010fa/ga/pa cli reference guide page 11 the global configuration mode manages the device configuration on a global level. The interface configuration mode configures specific interfaces in the device. 1.1.2 user exec mode after logging into the device, the user is automatically in user e...

  • Page 13

    Using the cli cli command modes page 12 1.1.4 global configuration mode global configuration mode commands apply to features that affect the system as a whole, rather than just a spe- cific interface. The configure privileged exec mode command is used to enter the global configuration mode. To enter...

  • Page 14: 1.2

    D-link des-3010fa/ga/pa cli reference guide page 13 • mac access-list —configures conditions required to allow traffic based on mac addresses. The mac access-list global configuration mode command is used to enter the mac access-list configuration mode.. 1.2 starting the cli the device can be manage...

  • Page 15: 1.3

    Using the cli editing features page 14 1.3 editing features 1.3.1 entering commands a cli command is a series of keywords and arguments. Keywords identify a command, and arguments specify configuration parameters. For example, in the command show interfaces status ethernet 8, show, interfaces and st...

  • Page 16

    D-link des-3010fa/ga/pa cli reference guide page 15 1.3.1.2 negating the effect of commands for many configuration commands, the prefix keyword no can be entered to cancel the effect of a command or reset the configuration to the default value. This guide describes the negation effect for all applic...

  • Page 17

    Screen display indicates system messages and prompts appearing on the console. All when a parameter is required to define a range of ports or parameters and all is an option, the default for the command is all when no parameters are defined. For exam- ple, the command interface range port-channel ha...

  • Page 18: Section 2. Aaa Commands

    D-link des-3010fa/ga/pa cli reference guide page 17 section 2. Aaa commands aaa authentication login the aaa authentication login global configuration mode command defines login authentication. To return to the default configuration, use the no form of this command. Syntax aaa authentication login {...

  • Page 19

    Aaa commands page 18 user guidelines the default and optional list names created with the aaa authentication login command are used with the login authentication command. Create a list by entering the aaa authentication login list-name method command for a particular protocol, where list-name is any...

  • Page 20: Aaa Authentication Enable

    D-link des-3010fa/ga/pa cli reference guide page 19 aaa authentication enable the aaa authentication enable global configuration mode command defines authentication method lists for accessing higher privilege levels. To return to the default configuration, use the no form of this command. Syntax aaa...

  • Page 21

    Aaa commands page 20 example the following example sets the enable password for authentication when accessing higher privilege levels. Console(config)# aaa authentication enable default enable.

  • Page 22: Login Authentication

    D-link des-3010fa/ga/pa cli reference guide page 21 login authentication the login authentication line configuration mode command specifies the login authentication method list for a remote telnet or console. To return to the default configuration specified by the aaa authentication login com- mand,...

  • Page 23: Enable Authentication

    Aaa commands page 22 enable authentication the enable authentication line configuration mode command specifies the authentication method list when accessing a higher privilege level from a remote telnet or console. To return to the default configuration specified by the aaa authentication enable com...

  • Page 24: Ip Http Authentication

    D-link des-3010fa/ga/pa cli reference guide page 23 ip http authentication the ip http authentication global configuration mode command specifies authentication methods for http server users. To return to the default configuration, use the no form of this command. Syntax ip http authentication metho...

  • Page 25: Ip Https Authentication

    Aaa commands page 24 ip https authentication the ip https authentication global configuration mode command specifies authentication methods for https server users. To return to the default configuration, use the no form of this command. Syntax ip https authentication method1 [method2...] no ip https...

  • Page 26: Show Authentication Methods

    D-link des-3010fa/ga/pa cli reference guide page 25 show authentication methods the show authentication methods privileged exec mode command displays information about the authentica- tion methods. Syntax show authentication methods default configuration this command has no default configuration. Co...

  • Page 27: Password

    Aaa commands page 26 password the password line configuration mode command specifies a password on a line. To remove the password, use the no form of this command. Syntax password password [encrypted] no password parameters • password — password for this level (range: 1-159 characters). • encrypted ...

  • Page 28: Enable Password

    D-link des-3010fa/ga/pa cli reference guide page 27 enable password the enable password global configuration mode command sets a local password to control access to user and privilege levels. To remove the password requirement, use the no form of this command. Syntax enable password [level level] pa...

  • Page 29: Username

    Aaa commands page 28 username the username global configuration mode command creates a user account in the local database. To remove a user name, use the no form of this command. Syntax username name [password password] [level level] [encrypted] no username name parameters • name — the name of the u...

  • Page 30: Bridge Address

    D-link des-3010fa/ga/pa cli reference guide page 29 section 3. Address table commands bridge address the bridge address interface configuration (vlan) mode command adds a mac-layer station source address to the bridge table. To delete the mac address, use the no form of this command. Syntax bridge a...

  • Page 31: Bridge Multicast Filtering

    Address table commands page 30 bridge multicast filtering the bridge multicast filtering global configuration mode command enables filtering multicast addresses. To dis- able filtering multicast addresses, use the no form of this command. Syntax bridge multicast filtering no bridge multicast filteri...

  • Page 32: Bridge Multicast Address

    D-link des-3010fa/ga/pa cli reference guide page 31 bridge multicast address the bridge multicast address interface configuration (vlan) mode command registers a mac-layer multicast address in the bridge table and statically adds ports to the group. To unregister the mac address, use the no form of ...

  • Page 33

    Address table commands page 32 bridge multicast forbidden address the bridge multicast forbidden address interface configuration (vlan) mode command forbids adding a spe- cific multicast address to specific ports. Use the no form of this command to return to the default configuration. Syntax bridge ...

  • Page 34: Bridge Multicast Forward-All

    D-link des-3010fa/ga/pa cli reference guide page 33 bridge multicast forward-all the bridge multicast forward-all interface configuration (vlan) mode command enables forwarding all multi- cast packets on a port. To restore the default configuration, use the no form of thiscommand. Syntax bridge mult...

  • Page 35

    Address table commands page 34 bridge multicast forbidden forward-all the bridge multicast forbidden forward-all interface configuration (vlan) mode command forbids a port to be a forward-all-multicast port. To restore the default configuration, use the no form of thiscommand. Syntax bridge multicas...

  • Page 36: Bridge Aging-Time

    D-link des-3010fa/ga/pa cli reference guide page 35 bridge aging-time the bridge aging-time global configuration mode command sets the address table aging time. To restore the default configuration, use the no form of this command. Syntax bridge aging-time seconds no bridge aging-time parameters • s...

  • Page 37: Clear Bridge

    Address table commands page 36 clear bridge the clear bridge privileged exec mode command removes any learned entries from the forwarding database. Syntax clear bridge default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user...

  • Page 38: Port Security

    D-link des-3010fa/ga/pa cli reference guide page 37 port security the port security interface configuration mode command locks the port, thereby, blocking unknown traffic and preventing the port from learning new addresses. To return to the default configuration, use the no form of this command. Syn...

  • Page 39

    Address table commands page 38 port security routed secure-address the port security routed secure-address interface configuration (ethernet, port-channel) mode command adds a mac-layer secure address to a routed port. Use the no form of this command to delete a mac address. Syntax port security rou...

  • Page 45

    Address table commands page 44 show bridge multicast filtering the show bridge multicast filtering user exec mode command displays the multicast filtering configuration. Syntax show bridge multicast filtering vlan-id parameters • vlan-id — vlan id value. Default configuration this command has no def...

  • Page 47

    Address table commands page 46 the following tables describes the fields shown above. Ch7 disabled ch8 disabled field description port port number status locked/unlocked action action on violation trap indicates if traps are sent in case of a violation frequency minimum time between consecutive trap...

  • Page 48: Section 4. Clock

    D-link des-3010fa/ga/pa cli reference guide page 47 section 4. Clock clock set the clock set privileged exec mode command manually sets the system clock. Syntax clock set hh:mm:ss day month year or clock set hh:mm:ss month day year parameters • hh:mm:ss — current time in hours (military format), min...

  • Page 49: Clock Source

    Clock page 48 clock source the clock source global configuration mode command configures an external time source for the system clock. Use no form of this command to disable external time source. Syntax clock source {sntp} no clock source parameters • sntp — sntp servers default configuration no ext...

  • Page 50: Clock Timezone

    D-link des-3010fa/ga/pa cli reference guide page 49 clock timezone the clock timezone global configuration mode command sets the time zone for display purposes. To set the time to the coordinated universal time (utc), use the no form of this command. Syntax clock timezone hours-offset minutes minute...

  • Page 51: Clock Summer-Time

    Clock page 50 clock summer-time the clock summer-time global configuration mode command configures the system to automatically switch to summer time (daylight saving time). To configure the software not to automatically switch to summer time, use the no form of this command. Syntax clock summer-time...

  • Page 52

    D-link des-3010fa/ga/pa cli reference guide page 51 user guidelines in both the date and recurring forms of the command, the first part of the command specifies when summer time begins, and the second part specifies when it ends. All times are relative to the local time zone. The start time is relat...

  • Page 53: Sntp Authentication-Key

    Clock page 52 sntp authentication-key the sntp authentication-key global configuration mode command defines an authentication key for simple net- work time protocol (sntp). To remove the authentication key for sntp, use the no form of this command. Syntax sntp authentication-key number md5 value no ...

  • Page 54: Sntp Authenticate

    D-link des-3010fa/ga/pa cli reference guide page 53 sntp authenticate the sntp authenticate global configuration mode command grants authentication for received simple network time protocol (sntp) traffic from servers. To disable the feature, use the no form of this command. Syntax sntp authenticate...

  • Page 55: Sntp Trusted-Key

    Clock page 54 sntp trusted-key the sntp trusted-key global configuration mode command authenticates the identity of a system to which sim- ple network time protocol (sntp) will synchronize. To disable authentication of the identity of the system, use the no form of this command. Syntax sntp trusted-...

  • Page 56: Sntp Client Poll Timer

    D-link des-3010fa/ga/pa cli reference guide page 55 sntp client poll timer the sntp client poll timer global configuration mode command sets the polling time for the simple network time protocol (sntp) client. To return to default configuration, use the no form of this command. Syntax sntp client po...

  • Page 57: Sntp Broadcast Client Enable

    Clock page 56 sntp broadcast client enable the sntp broadcast client enable global configuration mode command enables simple network time protocol (sntp) broadcast clients. To disable sntp broadcast clients, use the no form of this command. Syntax sntp broadcast client enable no sntp broadcast clien...

  • Page 58: Sntp Anycast Client Enable

    D-link des-3010fa/ga/pa cli reference guide page 57 sntp anycast client enable the sntp anycast client enable global configuration mode command enables sntp anycast client. To disable the sntp anycast client, use the no form of this command. Syntax sntp anycast client enable no sntp anycast client e...

  • Page 59

    Clock page 58 sntp client enable (interface) the sntp client enable interface configuration (ethernet, port-channel, vlan) mode command enables the sim- ple network time protocol (sntp) client on an interface. This applies to both receive broadcast and anycast updates. To disable the sntp client, us...

  • Page 60: Sntp Unicast Client Enable

    D-link des-3010fa/ga/pa cli reference guide page 59 sntp unicast client enable the sntp unicast client enable global configuration mode command enables the device to use the simple net- work time protocol (sntp) to request and accept sntp traffic from servers. To disable requesting and accepting snt...

  • Page 61: Sntp Unicast Client Poll

    Clock page 60 sntp unicast client poll the sntp unicast client poll global configuration mode command enables polling for the simple network time protocol (sntp) predefined unicast servers. To disable the polling for sntp client, use the no form of this com- mand. Syntax sntp unicast client poll no ...

  • Page 62: Sntp Server

    D-link des-3010fa/ga/pa cli reference guide page 61 sntp server the sntp server global configuration mode command configures the device to use the simple network time protocol (sntp) to request and accept sntp traffic from a specified server. To remove a server from the list of sntp servers, use the...

  • Page 63: Show Clock

    Clock page 62 show clock the show clock user exec mode command displays the time and date from the system clock. Syntax show clock [detail] parameters • detail — shows timezone and summertime configuration. Default configuration this command has no default configuration. Command mode user exec mode ...

  • Page 64: Show Sntp Configuration

    D-link des-3010fa/ga/pa cli reference guide page 63 show sntp configuration the show sntp configuration privileged exec mode command shows the configuration of the simple network time protocol (sntp). Syntax show sntp configuration default configuration this command has no default configuration. Com...

  • Page 65: Show Sntp Status

    Clock page 64 show sntp status the show sntp status privileged exec mode command shows the status of the simple network time protocol (sntp). Syntax show sntp status default configuration this command has no default configuration. Command mode privilegedexec mode user guidelines there are no user gu...

  • Page 66: Copy

    D-link des-3010fa/ga/pa cli reference guide page 65 section 5. Configuration and image files copy the copy privileged exec mode command copies files from a source to a destination. Syntax copy source-url destination-url parameters • source-url — the source file location url or reserved keyword of th...

  • Page 67

    Configuration and image files page 66 some invalid combinations of source and destination exist. Specifically, you cannot copy if one of the following conditions exist: the source file and destination file are the same file. Xmodem: is the destination file. The source file can be copied to image, bo...

  • Page 68

    D-link des-3010fa/ga/pa cli reference guide page 67 example the following example copies system image file1 from the tftp server 172.16.101.101 to a non-active image file. Console# copy tftp://172.16.101.101/file1 image accessing file 'file1' on 172.16.101.101... Loading file1 from 172.16.101.101: !...

  • Page 69: Delete

    Configuration and image files page 68 delete the delete privileged exec mode command deletes a file from a flash memory device. Syntax delete url parameters • url — a reserved keyword of the file to be deleted. (range: 1-160 characters) the following table displays the reserved keyword: default conf...

  • Page 70: Delete Startup-Config

    D-link des-3010fa/ga/pa cli reference guide page 69 delete startup-config the delete startup-config privileged exec mode command deletes the startup-config file. Syntax delete startup-config default configuration this command has no default configuration. Command mode privilegedexec mode user guidel...

  • Page 71: Show Running-Config

    Configuration and image files page 70 show running-config the show running-config privileged exec mode command displays the contents of the currently running config- uration file. Syntax show running-config default configuration this command has no default configuration. Command mode privileged exec...

  • Page 72: Show Startup-Config

    D-link des-3010fa/ga/pa cli reference guide page 71 show startup-config the show startup-config privileged exec mode command displays the contents of the startup configuration file. Syntax show startup-config default configuration this command has no default configuration. Command mode privileged ex...

  • Page 73: Interface Ethernet

    Ethernet configuration commands page 72 section 6. Ethernet configuration commands interface ethernet the interface ethernet global configuration mode command enters the interface configuration mode to configure an ethernet type interface. Syntax interface ethernet interface parameters • interface —...

  • Page 75: Shutdown

    Ethernet configuration commands page 74 shutdown the shutdown interface configuration (ethernet, port-channel) mode command disables an interface. To restart a disabled interface, use the no form of this command. Syntax shutdown no shutdown default configuration the interface is enabled. Command mod...

  • Page 76: Description

    D-link des-3010fa/ga/pa cli reference guide page 75 description the description interface configuration (ethernet, port-channel) mode command adds a description to an inter- face. To remove the description, use the no form of this command. Syntax description string no description parameters • string...

  • Page 78: Duplex

    D-link des-3010fa/ga/pa cli reference guide page 77 duplex the duplex interface configuration (ethernet) mode command configures the full/half duplex operation of a given ethernet interface when not using auto-negotiation. To restore the default configuration, use the no form of this command. Syntax...

  • Page 79: Negotiation

    Ethernet configuration commands page 78 negotiation the negotiation interface configuration (ethernet, port-channel) mode command enables auto-negotiation oper- ation for the speed and duplex parameters of a given interface. To disable auto-negotiation, use the no form of this command. Syntax negoti...

  • Page 82: Back-Pressure

    D-link des-3010fa/ga/pa cli reference guide page 81 back-pressure the back-pressure interface configuration (ethernet, port-channel) mode command enables back pressure on a given interface. To disable back pressure, use the no form of this command. Syntax back-pressure no back-pressure default confi...

  • Page 84: Set Interface Active

    D-link des-3010fa/ga/pa cli reference guide page 83 set interface active the set interface active privilegedexec mode command reactivates an interface that was shutdown. Syntax set interface active {ethernet interface port-channel-number} parameters • interface — valid ethernet port. (full syntax: p...

  • Page 86

    D-link des-3010fa/ga/pa cli reference guide page 85 ch3 enabled ch4 enabled ch5 enabled ch6 enabled.

  • Page 89

    Ethernet configuration commands page 88 ch1 not present ch2 not present ch3 not present ch4 not present ch5 not present ch6 not present.

  • Page 91

    Ethernet configuration commands page 90 ch2 ch3 ch4 ch5 ch6.

  • Page 93

    Ethernet configuration commands page 92 the following example displays counters for ethernet port 1. Port outoctets outucastpkts outmcastpkts outbcastpkts --- --------- ------------ ------------ ------------ 1 0 0 0 0 2 62887 0 623 96 3 24200 252 5 4 4 0 0 0 0 5 0 0 0 0 6 0 0 0 0 7 0 0 0 0 8 0 0 0 0...

  • Page 94

    D-link des-3010fa/ga/pa cli reference guide page 93 the following table describes the fields shown in the display: port outoctets outucastpkts outmcastpkts outbcastpkts ------ ----------- -------------- ------------ ------------ 1 9188 0 0 0 fcs errors: 0 single collision frames: 0 late collisions: ...

  • Page 95

    Ethernet configuration commands page 94 port storm-control include-multicast the port storm-control include-multicast interface configuration (ethernet) mode command counts multicast packets in broadcast storm control. To disable counting multicast packets, use the no form of this command. Syntax po...

  • Page 96

    D-link des-3010fa/ga/pa cli reference guide page 95 port storm-control broadcast enable the port storm-control broadcast enable interface configuration (ethernet) mode command enables broadcast storm control. To disable broadcast storm control, use the no form of this command. Syntax port storm-cont...

  • Page 97

    Ethernet configuration commands page 96 port storm-control broadcast rate the port storm-control broadcast rate interface configuration (ethernet) mode command configures the maxi- mum broadcast rate. To return to the default configuration, use the no form of this command. Syntax port storm-control ...

  • Page 98: Show Ports Storm-Control

    D-link des-3010fa/ga/pa cli reference guide page 97 show ports storm-control the show ports storm-control user or privileged exec mode command displays the storm control configura- tion. Syntax show ports storm-control [interface] parameters • interface — a valid ethernet port. (full syntax: port) d...

  • Page 99: Section 7. Gvrp Commands

    Gvrp commands page 98 section 7. Gvrp commands gvrp enable (global) garp vlan registration protocol (gvrp) is an industry-standard protocol designed to propagate vlan informa- tion from device to device. With gvrp, a single device is manually configured with all desired vlans for the net- work, and ...

  • Page 100: Gvrp Enable (Interface)

    Ethernet configuration commands page 76 speed the speed interface configuration (ethernet, port-channel) mode command configures the speed of a given ethernet interface when not using auto-negotiation. To restore the default configuration, use the no form of this command. Syntax speed {10

  • Page 102: Gvrp Vlan-Creation-Forbid

    D-link des-3010fa/ga/pa cli reference guide page 101 gvrp vlan-creation-forbid the gvrp vlan-creation-forbid interface configuration (ethernet, port-channel) mode command disables dynamic vlan creation or modification. To enable dynamic vlan creation or modification, use the no form of this command....

  • Page 103: Gvrp Registration-Forbid

    Gvrp commands page 102 gvrp registration-forbid the gvrp registration-forbid interface configuration (ethernet, port-channel) mode command deregisters all dynamic vlans on a port and prevents vlan creation or registration on the port. To allow dynamic registration of vlans on a port, use the no form...

  • Page 105: Show Gvrp Configuration

    Gvrp commands page 104 show gvrp configuration the show gvrp configuration user orprivileged exec mode command displays gvrp configuration informa- tion, including timer values, whether gvrp and dynamic vlan creation is enabled, and which ports are running gvrp. Syntax show gvrp configuration [ether...

  • Page 108: Ip Igmp Snooping (Global)

    D-link des-3010fa/ga/pa cli reference guide page 107 section 8. Igmp snooping commands ip igmp snooping (global) the ip igmp snooping global configuration mode command enables internet group management protocol (igmp) snooping. To disable igmp snooping, use the no form of this command. Syntax ip igm...

  • Page 109: Ip Igmp Snooping (Interface)

    Igmp snooping commands page 108 ip igmp snooping (interface) the ip igmp snooping interface configuration (vlan) mode command enables internet group management protocol (igmp) snooping on a specific vlan. To disable igmp snooping on a vlan interface, use the no form of this command. Syntax ip igmp s...

  • Page 110

    D-link des-3010fa/ga/pa cli reference guide page 109 ip igmp snooping host-time-out the ip igmp snooping host-time-out interface configuration (vlan) mode command configures the host-time- out. If an igmp report for a multicast group was not received for a host-time-out period from a specific port, ...

  • Page 111

    Igmp snooping commands page 110 ip igmp snooping mrouter-time-out the ip igmp snooping mrouter-time-out interface configuration (vlan) mode command configures the mrouter-time-out. The ip igmp snooping mrouter-time-out interface configuration (vlan) mode command is used for setting the aging-out tim...

  • Page 112

    D-link des-3010fa/ga/pa cli reference guide page 111 ip igmp snooping leave-time-out the ip igmp snooping leave-time-out interface configuration (vlan) mode command configures the leave- time-out. If an igmp report for a multicast group was not received for a leave-time-out period after an igmp leav...

  • Page 113

    Igmp snooping commands page 112 show ip igmp snooping mrouter the show ip igmp snooping mrouter user orprivileged exec mode command displays information on dynam- ically learned multicast router interfaces. Syntax show ip igmp snooping mrouter [interface vlan-id] parameters • vlan-id — vlan number. ...

  • Page 114

    D-link des-3010fa/ga/pa cli reference guide page 113 show ip igmp snooping interface the show ip igmp snooping interface user orprivileged exec mode command displays igmp snooping con- figuration. Syntax show ip igmp snooping interface vlan-id parameters • vlan-id — vlan number. Default configuratio...

  • Page 115: Show Ip Igmp Snooping Groups

    Igmp snooping commands page 114 show ip igmp snooping groups the show ip igmp snooping groups user exec mode command displays multicast groups learned by igmp snooping. Syntax show ip igmp snooping groups [vlan vlan-id][address ip-multicast-address] parameters • vlan-id — vlan number. • ip-multicast...

  • Page 117: Ip Address Dhcp

    Ip addressing commands page 116 ip address dhcp the ip address dhcp interface configuration (ethernet, vlan, port-channel) mode command acquires an ip address for an ethernet interface from the dynamic host configuration protocol (dhcp) server. To deconfigure an acquired ip address, use the no form ...

  • Page 118: Ip Default-Gateway

    D-link des-3010fa/ga/pa cli reference guide page 117 ip default-gateway the ip default-gateway global configuration mode command defines a default gateway (router). To return to the default configuration, use the no form of this command. Syntax ip default-gateway ip-address no ip default-gateway par...

  • Page 121: Arp Timeout

    Ip addressing commands page 120 arp timeout the arp timeout global configuration mode command configures how long an entry remains in the arp cache. To return to the default configuration, use the no form of this command. Syntax arp timeout seconds no arp timeout parameters • seconds — time (in seco...

  • Page 122: Clear Arp-Cache

    D-link des-3010fa/ga/pa cli reference guide page 121 clear arp-cache the clear arp-cache privileged exec mode command deletes all dynamic entries from the arp cache. Syntax clear arp-cache default configuration this command has no default configuration. Command mode privileged exec mode user guideli...

  • Page 123: Show Arp

    Ip addressing commands page 122 show arp the show arp privileged exec mode command displays entries in the arp table. Syntax show arp default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidelines for this command. Exam...

  • Page 124: Ip Domain-Name

    D-link des-3010fa/ga/pa cli reference guide page 123 ip domain-name the ip domain-name global configuration mode command defines a default domain name used by the software to complete unqualified host names (names without a dotted-decimal domain name). To remove the default domain name, use the no f...

  • Page 125: Ip Name-Server

    Ip addressing commands page 124 ip name-server the ip name-server global configuration mode command defines the available name servers. To remove a name server, use the no form of this command. Syntax ip name-server server-address [server-address2 … server-address8] no ip name-server [server-address...

  • Page 126: Ip Host

    D-link des-3010fa/ga/pa cli reference guide page 125 ip host the ip host global configuration mode command defines static host name-to-address mapping in the host cache. Toremove the name-to-address mapping, use the no form of this command. Syntax ip host name address no ip host name parameters • na...

  • Page 129: Show Hosts

    Ip addressing commands page 128 show hosts the show hosts privileged exec mode command displays the default domain name, a list of name server hosts, the static and the cached list of host names and addresses. Syntax show hosts [name] parameters • name — specifies the host name. (range: 1-158 charac...

  • Page 130: Section 10. Lacp Commands

    D-link des-3010fa/ga/pa cli reference guide page 129 section 10. Lacp commands lacp system-priority the lacp system-priority global configuration mode command configures the system priority. To return to the default configuration, use the no form of this command. Syntax lacp system-priority value no...

  • Page 131: Lacp Port-Priority

    Lacp commands page 130 lacp port-priority the lacp port-priority interface configuration (ethernet) mode command configures physical port priority. To return to the default configuration, use the no form of this command. Syntax lacp port-priority value no lacp port-priority parameters • value — spec...

  • Page 134

    D-link des-3010fa/ga/pa cli reference guide page 133 distributing: false expired: false partner system priority: 0 system mac addr: 00:00:00:00:00:00 port admin key: 0 port oper key: 0 port oper number: 0 port admin priority: 0 port oper priority: 0 port oper timeout: long lacp activity: passive agg...

  • Page 135: Show Lacp Port-Channel

    Lacp commands page 134 show lacp port-channel the show lacp port-channel privileged exec mode command displays lacp information for a port-channel. Syntax show lacp port-channel [port_channel_number] parameters • port_channel_number — validport-channel number. Default configuration this command has ...

  • Page 137: Speed

    Line commands page 136 speed the speed line configuration mode command sets the line baud rate. To return to the default configuration, use the no form of the command. Syntax speed bps no speed parameters • bps—baud rate in bits per second (bps). Possible values are 2400, 4800, 9600, 19200, and 3840...

  • Page 138: Exec-Timeout

    D-link des-3010fa/ga/pa cli reference guide page 137 exec-timeout the exec-timeout line configuration mode command sets the interval that the system waits until user input is detected. To return to the default configuration, use the no form of this command. Syntax exec-timeout minutes [seconds] no e...

  • Page 139: History

    Line commands page 138 history the history line configuration mode command enables the command history function. To disable the command history function, use the no form of this command. Syntax history no history default configuration the command history function is enabled. Command mode line config...

  • Page 140: History Size

    D-link des-3010fa/ga/pa cli reference guide page 139 history size the history size line configuration mode command configures the command history buffer size for a particular line. To reset the command history buffer size to the default configuration, use the no form of this command. Syntax history ...

  • Page 141: Terminal History

    Line commands page 140 terminal history the terminal history user or priviliged exec command enables the command history function for the current ter- minal session. To disable the command history function, use the no form of this command. Syntax terminal history no terminal history default configur...

  • Page 142: Terminal History Size

    D-link des-3010fa/ga/pa cli reference guide page 141 terminal history size the terminal history size user or priviliged exec command configures the command history buffer size for the current terminal session. To reset the command history buffer size to the default setting, use the no form of this c...

  • Page 144: Section 12. Management Acl

    D-link des-3010fa/ga/pa cli reference guide page 143 section 12. Management acl management access-list the management access-list globalconfiguration mode command configures a management access list and enters the management access-list configuration command mode. To delete an access list, use the n...

  • Page 145

    Management acl page 144 the following example creates a management access list called mlist, configures all interfaces to be management interfaces except ethernet interfaces 1 and 6 and makes the new access list the active list. Console(config)# management access-list mlist console(config-macl)# den...

  • Page 148: Management Access-Class

    D-link des-3010fa/ga/pa cli reference guide page 147 management access-class the management access-class global configuration mode command restricts management connections by defining the active management access list. To disable this restriction, use the no form of this command. Syntax management a...

  • Page 149: Show Management Access-List

    Management acl page 148 show management access-list the show management access-list privileged exec mode command displays management access-lists. Syntax show management access-list [name] parameters • name — specifies the name of a management access list. (range: 1 - 32 characters) default configur...

  • Page 150: Show Management Access-Class

    D-link des-3010fa/ga/pa cli reference guide page 149 show management access-class the show management access-class privileged exec mode command displays the active management access list. Syntax show management access-class default configuration this command has no default configuration. Command mod...

  • Page 151: Test Copper-Port Tdr

    Phy diagnostics commands page 150 section 13. Phy diagnostics commands test copper-port tdr the test copper-port tdr privileged exec mode command uses time domain reflectometry (tdr) technology to diagnose the quality and characteristics of a copper cable attached to a port. Syntax test copper-port ...

  • Page 152: Show Copper-Ports Tdr

    D-link des-3010fa/ga/pa cli reference guide page 151 show copper-ports tdr the show copper-ports tdr user or privileged exec mode command displays information on the last time a domain reflectometry (tdr) test was performed on the copper ports. Syntax show copper-ports tdr [interface] parameters • i...

  • Page 153

    Phy diagnostics commands page 152 show copper-ports cable-length the show copper-ports cable-length user or privileged exec mode command displays the estimated copper cable length attached to a port. Syntax show copper-ports cable-length [interface] parameters • interface — a valid ethernet port. (f...

  • Page 154

    D-link des-3010fa/ga/pa cli reference guide page 153 show fiber-ports optical-transceiver the show fiber-ports optical-transceiver privileged exec command displays the optical transceiver diagnos- tics. Syntax show fiber-ports optical-transceiver [interface] [detailed] parameters • interface — a val...

  • Page 155: Interface Port-Channel

    Port trunking commands page 154 section 14. Port trunking commands interface port-channel the interface port-channel global configuration mode command enters the interface configuration mode to con- figure a specific port-channel. Syntax interface port-channel port-channel-number parameters • port-c...

  • Page 158: Show Interfaces Port-Channel

    D-link des-3010fa/ga/pa cli reference guide page 157 show interfaces port-channel the show interfaces port-channel privileged exec mode command displays port-channel information. Syntax show interfaces port-channel [port-channel-number] parameters • port-channel-number — valid port-channel number. D...

  • Page 160: Port Monitor Vlan-Tagging

    D-link des-3010fa/ga/pa cli reference guide page 159 port monitor vlan-tagging the port monitor interface configuration (ethernet) mode command transmits tagged ingress mirrored packets. To transmit untagged ingress mirrored packets, use the no form of this command. Syntax port monitor vlan-tagging ...

  • Page 161: Show Ports Monitor

    Port monitor commands page 160 show ports monitor the show ports monitor user or privileged execmode command displays the port monitoring status. Syntax show ports monitor default configuration this command has no default configuration. Command mode user or privileged exec mode user guidelines there...

  • Page 163

    System management page 162 examples the following example displays pinging results: console> ping 10.1.1.1 pinging 10.1.1.1 with 64 bytes of data: 64 bytes from 10.1.1.1: icmp_seq=0. Time=11 ms 64 bytes from 10.1.1.1: icmp_seq=1. Time=8 ms 64 bytes from 10.1.1.1: icmp_seq=2. Time=8 ms 64 bytes from ...

  • Page 165

    System management page 164 examples the following example discovers the routes that packets will actually take when traveling to their destination. The following table describes significant fields shown above. The following table describes characters that may appear in the traceroute command output....

  • Page 166: Reload

    D-link des-3010fa/ga/pa cli reference guide page 165 reload the reload privileged exec mode command reloads the operating system. Syntax reload default configuration this command has no default configuration. Command mode privileged exec mode user guidelines caution should be exercised when resettin...

  • Page 167: Hostname

    System management page 166 hostname the hostname global configuration mode command specifies or modifies the device host name. To remove the existing host name, use the no form of the command. Syntax hostname name no hostname parameters • name — the host name. Of the device. (range: 1-158 characters...

  • Page 168: Show Users

    D-link des-3010fa/ga/pa cli reference guide page 167 show users the show users user or privileged exec mode command displays information about the active users. Syntax show users default configuration this command has no default configuration. Command mode user or privileged exec mode user guideline...

  • Page 169: Show System

    System management page 168 show system the show system user or privileged exec mode command displays system information. Syntax show system default configuration this command has no default configuration. Command mode user or privileged exec mode user guidelines there are no user guidelines for this...

  • Page 170: Show Version

    D-link des-3010fa/ga/pa cli reference guide page 169 show version the show version user or privileged exec mode command displays system version information. Syntax show version default configuration this command has no default configuration. Command mode user or privileged exec mode user guidelines ...

  • Page 171: Show System Id

    System management page 170 show system id the show system id user or privileged exec mode command displays system id information. Syntax show system id default configuration this command has no default configuration. Command mode user or privileged exec mode user guidelines there are no user guideli...

  • Page 172: Section 17. Qos Commands

    D-link des-3010fa/ga/pa cli reference guide page 171 section 17. Qos commands qos the qos global configuration mode command enables quality of service (qos) on the device. To disable qos on the device, use the no form of this command. Syntax qos no qos default configuration qos is disabled on the de...

  • Page 173: Show Qos

    Qos commands page 172 show qos the show qos user or privileged exec mode command displays quality of service (qos) for the device. Syntax show qos default configuration this command has no default configuration. Command mode user or privileged exec mode user guidelines there are no user guidelines f...

  • Page 174

    D-link des-3010fa/ga/pa cli reference guide page 173 priority-queue out num-of-queues the priority-queue out num-of-queues global configuration mode command configures the number of expedite queues. To return to the default configuration, use the no form of this command. Syntax priority-queue out nu...

  • Page 175

    Qos commands page 174 rate-limit interface configuration the rate-limit interface configuration command limits the rate of the incoming traffic. The no form of this com- mand is used to disable rate limit. Syntax rate-limit rate no rate-limit parameters • kbps maximum of kilobits per second of ingre...

  • Page 177

    Qos commands page 176 switch> show qos interface 7 rate-limit port rate-limit [kbps] 7 100 3 2 4 3 5 3 6 4 7 4.

  • Page 178: Traffic-Shape

    D-link des-3010fa/ga/pa cli reference guide page 177 traffic-shape the traffic-shape interface configuration (ethernet, port-channel) mode command activates the traffic shaper on egress ports or egress queues. Use the no form of this command to disable the shaper. Syntax traffic-shape { committed-ra...

  • Page 179: Wrr-Queue Cos-Map

    Qos commands page 178 wrr-queue cos-map the wrr-queue cos-map global configuration mode command maps class of service (cos) values to a specific egress queue. To return to the default configuration, use the no form of this command. Syntax wrr-queue cos-map queue-id cos1...Cos8 no wrr-queue cos-map p...

  • Page 180: Qos Map Dscp-Queue

    D-link des-3010fa/ga/pa cli reference guide page 179 qos map dscp-queue the qos map dscp-queue global configuration mode command modifies the dscp to cos map. To return to the default map, use the no form of this command. Syntax qos map dscp-queue dscp-list to queue-id no qos map dscp-queue [dscp-li...

  • Page 182: Qos Trust (Interface)

    D-link des-3010fa/ga/pa cli reference guide page 181 qos trust (interface) the qos trust interface configuration (ethernet, port-channel) mode command enables each port trust state while the system is in the basic qos mode. To disable the trust state on each port, use the no form of this command. Sy...

  • Page 183: Qos Cos

    Qos commands page 182 qos cos the qos cos interface configuration (ethernet, port-channel) mode command defines the default cos value of a port. To return to the default configuration, use the no form of this command. Syntax qos cos default-cos no qos cos parameters • default-cos — specifies the def...

  • Page 184: Show Qos Map

    D-link des-3010fa/ga/pa cli reference guide page 183 show qos map the show qos map user or privileged exec mode command displays all qos maps. Syntax show qos map [dscp-queue] parameters • dscp-queue — indicates the dscp to queue map. Default configuration this command has no default configuration. ...

  • Page 186

    D-link des-3010fa/ga/pa cli reference guide page 185 example the following example specifies a radius server host with ip address 192.168.10.1, authentication request port number 20 and a 20-second timeout period. Console(config)# radius-server host 192.168.10.1 auth-port 20 timeout 20

  • Page 187: Radius-Server Key

    Radius commands page 186 radius-server key the radius-server key global configuration mode command sets the authentication and encryption key for all radius communications between the device and the radius daemon. To return to the default configuration, use the no form of this command. Syntax radius...

  • Page 188: Radius-Server Retransmit

    D-link des-3010fa/ga/pa cli reference guide page 187 radius-server retransmit the radius-server retransmit global configuration mode command specifies the number of times the software searches the list of radius server hosts. To reset the default configuration, use the no form of this command. Synta...

  • Page 189: Radius-Server Source-Ip

    Radius commands page 188 radius-server source-ip the radius-server source-ip global configuration mode command specifies the source ip address used for communication with radius servers. To return to the default configuration, use the no form of this command. Syntax radius-server source-ip source no...

  • Page 190: Radius-Server Timeout

    D-link des-3010fa/ga/pa cli reference guide page 189 radius-server timeout the radius-server timeout global configuration mode command sets the interval during which the device waits for a server host to reply. To return to the default configuration, use the no form of this command. Syntax radius-se...

  • Page 191: Radius-Server Deadtime

    Radius commands page 190 radius-server deadtime the radius-server deadtime global configuration mode command improves radius response time when serv- ers are unavailable. The command is used to cause the unavailable servers to be skipped. To return to the default configuration, use the no form of th...

  • Page 192: Show Radius-Servers

    D-link des-3010fa/ga/pa cli reference guide page 191 show radius-servers the show radius-servers user or privileged exec mode command displays the radius server settings. Syntax show radius-servers default configuration this command has no default configuration. Command mode user or privileged exec ...

  • Page 193

    Radius commands page 192.

  • Page 195: Power Inline Powered-Device

    Power over ethernet page 194 power inline powered-device the power inline powered-device interface configuration command adds a description of the powered device type. Use the no form of this command to remove the description. Syntax power inline powered-device pd-type no power inline powered-device...

  • Page 196: Power Inline Usage-Threshold

    D-link des-3010fa/ga/pa cli reference guide page 195 power inline usage-threshold the power inline usage-threshold global configuration command configures the threshold for initiating inline power usage alarms. Use the no form of this command to return to default. Syntax power inline usage-threshold...

  • Page 197: Power Inline Traps Enable

    Power over ethernet page 196 power inline traps enable the power inline traps enable global configuration command enable inline power traps. Use the no form of this command to disable traps. Syntax power inline traps enable no power inline traps enable parameters this command has no arguments or key...

  • Page 198: Show Power Inline

    D-link des-3010fa/ga/pa cli reference guide page 197 show power inline the show power inline exec command displays information about the inline power. The mode is privileged exec mode. Syntax show power inline [interface] parameters • interface — valid ethernet port. Default configuration command mo...

  • Page 199

    Power over ethernet page 198 the following table describes the fields shown in the display: denied counter absent counter invalid signature counter: 0 field description power the inline power sourcing equipment operational status. Nominal power the inline power sourcing equipment nominal power in wa...

  • Page 201

    Rmon commands page 200 the following table describes significant fields shown above: field description dropped octets the total number of octets of data (including those in bad packets) received on the net- work (excluding framing bits but including fcs octets). Packets the total number of packets (...

  • Page 202: Rmon Collection History

    D-link des-3010fa/ga/pa cli reference guide page 201 rmon collection history the rmon collection history interface configuration (ethernet, port-channel) mode command enables a remote monitoring (rmon) mib history statistics group on an interface. To remove a specified rmon history statistics group,...

  • Page 205

    Rmon commands page 204 the following table describes significant fields shown above: maximum table size: 500 (800 after reset) time crc align undersize oversize fragments jabbers ---------- --------- --------- -------- --------- ------- jan 18 2002 21:57:00 1 1 0 49 0 jan 18 2002 21:57:30 1 1 0 27 0...

  • Page 206

    D-link des-3010fa/ga/pa cli reference guide page 205 fragments the total number of packets received during this sampling interval that were less than 64 octets in length (excluding framing bits but including fcs octets) had either a bad frame check sequence (fcs) with an integral number of octets (f...

  • Page 207: Rmon Alarm

    Rmon commands page 206 rmon alarm the rmon alarm global configuration mode command configures alarm conditions. To remove an alarm, use the no form of this command. Syntax rmon alarm index variable interval rthreshold fthreshold revent fevent [type type] [startup direction] [owner name] no rmon alar...

  • Page 208

    D-link des-3010fa/ga/pa cli reference guide page 207 example the following example configures the following alarm conditions: • alarm index — 1000 • sample interval — 360000 seconds • rising threshold — 1000000 • falling threshold — 1000000 • rising threshold event index — 10 • falling threshold eve...

  • Page 209: Show Rmon Alarm

    Rmon commands page 208 show rmon alarm the show rmon alarm user or privileged exec mode command displays alarm configuration. Syntax show rmon alarm number parameters • number — specifies the alarm index. (range: 1 - 65535) default configuration this command has no default configuration. Command mod...

  • Page 210

    D-link des-3010fa/ga/pa cli reference guide page 209 interval the interval in seconds over which the data is sampled and compared with the rising and falling thresholds. Sample type the method of sampling the variable and calculating the value compared against the thresholds. If the value is absolut...

  • Page 211: Rmon Event

    Rmon commands page 210 rmon event the rmon event global configuration mode command configures an event. To remove an event, use the no form of this command. Syntax rmon event index type [community text][description text] [owner name] no rmon event index parameters • index — specifies the event index...

  • Page 212: Show Rmon Events

    D-link des-3010fa/ga/pa cli reference guide page 211 show rmon events the show rmon events user exec mode command displays the rmon event table. Syntax show rmon events default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guid...

  • Page 213: Show Rmon Log

    Rmon commands page 212 show rmon log the show rmon log user exec mode command displays the rmon log table. Syntax show rmon log [event] parameters • event — specifies the event index. (range: 0 - 65535) default configuration this command has no default configuration. Command mode user exec mode user...

  • Page 214

    D-link des-3010fa/ga/pa cli reference guide page 213 the following table describes the significant fields shown in the display: field description event an index that uniquely identifies the event. Description a comment describing this event. Time the time this entry was created..

  • Page 216: Section 21. Snmp Commands

    D-link des-3010fa/ga/pa cli reference guide page 215 section 21. Snmp commands snmp-server community the snmp-server community global configuration mode command configures the community access string to permit access to the snmp protocol. To remove the specified community string, use the no form of ...

  • Page 217

    Snmp commands page 216 examples the following example defines community access string public to permit administrative access to snmp protocol at an administrative station with ip address 192.168.1.20. Console(config)# snmp-server community public su 192.168.1.20

  • Page 218: Snmp-Server View

    D-link des-3010fa/ga/pa cli reference guide page 217 snmp-server view the snmp-server view global configuration mode command creates or updates a simple network management protocol (snmp) server view entry. To remove a specified snmp server view entry, use the no form of this com- mand. Syntax snmp-...

  • Page 219: Snmp-Server Group

    Snmp commands page 218 snmp-server group the snmp-server group global configuration mode command configures a new simple management protocol (snmp) group or a table that maps snmp users to snmp views. To remove a specified snmp group, use the no form of this command. Syntax snmp-server group groupna...

  • Page 220: Snmp-Server User

    D-link des-3010fa/ga/pa cli reference guide page 219 snmp-server user the snmp-server user global configuration mode command configures a new snmp version 3 user. To remove a user, use the no form of this command. Syntax snmp-server user username groupname [remote engineid-string] [ auth-md5 passwor...

  • Page 221

    Snmp commands page 220 examples the following example configures an snmpv3 user john in group user-group. Console(config)# snmp-server user john user-group.

  • Page 222: Snmp-Server Engineid Local

    D-link des-3010fa/ga/pa cli reference guide page 221 snmp-server engineid local the snmp-server engineid local global configuration mode command specifies the simple network manage- ment protocol (snmp) engineid on the local device. To remove the configured engine id, use the no form of this command...

  • Page 223

    Snmp commands page 222 examples the following example enables snmpv3 on the device and sets the local engine id of the device to the default value. Console(config) # snmp-server engineid local default.

  • Page 224: Snmp-Server Enable Traps

    D-link des-3010fa/ga/pa cli reference guide page 223 snmp-server enable traps the snmp-server enable traps global configuration mode command enables the device to send snmp traps. To disable snmp traps, use the no form of the command. Syntax snmp-server enable traps no snmp-server enable traps defau...

  • Page 225: Snmp-Server Filter

    Snmp commands page 224 snmp-server filter the snmp-server filter global configuration mode command creates or updates a simple network management protocol (snmp) server filter entry. To remove the specified snmp server filter entry, use the no form of this com- mand. Syntax snmp-server filter filter...

  • Page 226: Snmp-Server Host

    D-link des-3010fa/ga/pa cli reference guide page 225 snmp-server host the snmp-server host global configuration mode command specifies the recipient of simple network manage- ment protocol version 1 or version 2 notifications. To remove the specified host, use the no form of this command. Syntax snm...

  • Page 228

    D-link des-3010fa/ga/pa cli reference guide page 227 snmp-server trap authentication the snmp-server trap authentication global configuration mode command enables the device to send snmp traps when authentication fails. To disable snmp failed authentication traps, use the no form of this command. Sy...

  • Page 229: Snmp-Server Contact

    Snmp commands page 228 snmp-server contact the snmp-server contact global configuration mode command configures the system contact (syscontact) string. To remove system contact information, use the no form of the command. Syntax snmp-server contact text no snmp-server contact parameters • text — spe...

  • Page 230: Snmp-Server Location

    D-link des-3010fa/ga/pa cli reference guide page 229 snmp-server location the snmp-server location global configuration mode command configures the system location string. To remove the location string, use the no form of this command. Syntax snmp-server location text no snmp-server location paramet...

  • Page 231: Snmp-Server Set

    Snmp commands page 230 snmp-server set the snmp-server set global configuration mode command defines the snmp mib value. Syntax snmp-server set variable-name name1 value1 [ name2 value2 …] parameters • variable-name — mib variable name. (range 1-160 characters). • name value — list of name and value...

  • Page 232: Show Snmp

    D-link des-3010fa/ga/pa cli reference guide page 231 show snmp the show snmp privileged exec mode command displays the snmp status. Syntax show snmp default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidelines for thi...

  • Page 233

    Snmp commands page 232 the following table describes significant fields shown above. Version 3 notifications target address type username security level udp port filter name to sec retries -------------- ----- --------- ------- ---- ------ --- ------- 192.122.173.42 inform bob priv 162 15 3 system c...

  • Page 234: Show Snmp Engineid

    D-link des-3010fa/ga/pa cli reference guide page 233 show snmp engineid the show snmp engineid privileged exec mode command displays the id of the local simple network man- agement protocol (snmp) engine. Syntax show snmp engineid default configuration this command has no default configuration. Comm...

  • Page 235: Show Snmp Views

    Snmp commands page 234 show snmp views the show snmp views privileged exec mode command displays the configuration of views. Syntax show snmp views [viewname] parameters • viewname — specifies the name of the view. (range: 1-30) default configuration this command has no default configuration. Comman...

  • Page 236: Show Snmp Groups

    D-link des-3010fa/ga/pa cli reference guide page 235 show snmp groups the show snmp groups privileged exec mode command displays the configuration of groups. Syntax show snmp groups [groupname] parameters • groupname—specifies the name of the group. (range: 1-30) default configuration this command h...

  • Page 237

    Snmp commands page 236 write name of the view that enables entering data and managing the contents of the agent. Notify name of the view that enables specifying an inform or a trap..

  • Page 238: Show Snmp Filters

    D-link des-3010fa/ga/pa cli reference guide page 237 show snmp filters the show snmp filters privileged exec mode command displays the configuration of filters. Syntax show snmp filters [filtername] parameters • filtername—specifies the name of the filter. (range: 1-30) default configuration this co...

  • Page 239: Show Snmp Users

    Snmp commands page 238 show snmp users the show snmp users privileged exec mode command displays the configuration of users. Syntax show snmp users [username] parameters • username—specifies the name of the user. (range: 1-30) default configuration this command has no default configuration. Command ...

  • Page 240: Spanning-Tree

    D-link des-3010fa/ga/pa cli reference guide page 239 section 22. Spanning-tree commands spanning-tree the spanning-tree global configuration mode command enables spanning-tree functionality. To disable span- ning-tree functionality, use the no form of this command. Syntax spanning-tree no spanning-t...

  • Page 242: Spanning-Tree Forward-Time

    D-link des-3010fa/ga/pa cli reference guide page 241 spanning-tree forward-time the spanning-tree forward-time global configuration mode command configures the spanning-tree bridge for- ward time, which is the amount of time a port remains in the listening and learning states before entering the for...

  • Page 243: Spanning-Tree Hello-Time

    Spanning-tree commands page 242 spanning-tree hello-time the spanning-tree hello-time global configuration mode command configures the spanning tree bridge hello time, which is how often the device broadcasts hello messages to other devices.To return to the default configura- tion, use the no form o...

  • Page 244: Spanning-Tree Max-Age

    D-link des-3010fa/ga/pa cli reference guide page 243 spanning-tree max-age the spanning-tree max-age global configuration mode command configures the spanning tree bridge maximum age. To return to the default configuration, use the no form of this command. Syntax spanning-tree max-age seconds no spa...

  • Page 245: Spanning-Tree Priority

    Spanning-tree commands page 244 spanning-tree priority the spanning-tree priority global configuration mode command configures the spanning tree priority of the device. The priority value is used to determine which bridge is elected as the root bridge. To return to the default configuration, use the...

  • Page 246: Spanning-Tree Disable

    D-link des-3010fa/ga/pa cli reference guide page 245 spanning-tree disable the spanning-tree disable interface configuration mode command disables spanning tree on a specific port. To enable spanning tree on a port, use the no form of this command. Syntax spanning-tree disable no spanning-tree disab...

  • Page 247: Spanning-Tree Cost

    Spanning-tree commands page 246 spanning-tree cost the spanning-tree cost interface configuration mode command configures the spanning tree path cost for a port. To return to the default configuration, use the no form of this command. Syntax spanning-tree cost cost no spanning-tree cost parameters •...

  • Page 248: Spanning-Tree Port-Priority

    D-link des-3010fa/ga/pa cli reference guide page 247 spanning-tree port-priority the spanning-tree port-priority interface configuration mode command configures port priority. To return to the default configuration, use the no form of this command. Syntax spanning-tree port-priority priority no span...

  • Page 249: Spanning-Tree Portfast

    Spanning-tree commands page 248 spanning-tree portfast the spanning-tree portfast interface configuration mode command enables portfast mode. In portfast mode, the interface is immediately put into the forwarding state upon linkup without waiting for the standard forward time delay. To disable portf...

  • Page 250: Spanning-Tree Link-Type

    D-link des-3010fa/ga/pa cli reference guide page 249 spanning-tree link-type the spanning-tree link-type interface configuration mode command overrides the default link-type setting deter- mined by the duplex mode of the port and enables rapid spanning tree protocol (rstp) transitions to the for- wa...

  • Page 252: Spanning-Tree Bpdu

    D-link des-3010fa/ga/pa cli reference guide page 251 spanning-tree bpdu the spanning-tree bpdu global configuration mode command defines bpdu handling when the spanning tree is disabled globally or on a single interface. To return to the default configuration, use the no form of this command. Syntax...

  • Page 253

    Spanning-tree commands page 252 clear spanning-tree detected-protocols the clear spanning-tree detected-protocols privileged exec mode command restarts the protocol migration process (forces renegotiation with neighboring devices) on all interfaces or on a specified interface. Syntax clear spanning-...

  • Page 254: Spanning-Tree Guard Root

    D-link des-3010fa/ga/pa cli reference guide page 253 spanning-tree guard root the spanning-tree guard root interface configuration command enables root guard on all spanning tree instances on that interface. Root guard restricts the interface to be the root port for the switch. To disable root guard...

  • Page 255: Spanning-Tree Mst Priority

    Spanning-tree commands page 254 spanning-tree mst priority the spanning-tree mst priority global configuration mode command configures the device priority for the spec- ified spanning-tree instance. To return to the default configuration, use the no form of this command. Syntax spanning-tree mst ins...

  • Page 256: Spanning-Tree Mst Max-Hops

    D-link des-3010fa/ga/pa cli reference guide page 255 spanning-tree mst max-hops the spanning-tree mst priority global configuration mode command configures the number of hops in an mst region before the bdpu is discarded and the port information is aged out. To return to the default configuration, u...

  • Page 257

    Spanning-tree commands page 256 spanning-tree mst port-priority the spanning-tree mst port-priority interface configuration mode command configures port priority for the specified mst instance. To return to the default configuration, use the no form of this command. Syntax spanning-tree mst instance...

  • Page 258: Spanning-Tree Mst Cost

    D-link des-3010fa/ga/pa cli reference guide page 257 spanning-tree mst cost the spanning-tree mst cost interface configuration mode command configures the path cost for multiple span- ning tree (mst) calculations. If a loop occurs, the spanning tree considers path cost when selecting an interface to...

  • Page 259

    Spanning-tree commands page 258 spanning-tree mst configuration the spanning-tree mst configuration global configuration mode command enables configuring an mst region by entering the multiple spanning tree (mst) mode. Syntax spanning-tree mst configuration default configuration this command has no ...

  • Page 261: Name (Mst)

    Spanning-tree commands page 260 name (mst) the name mst configuration mode command defines the configuration name. To return to the default setting, use the no form of this command. Syntax name string parameters • string—mst configuration name. Case-sensitive (range: 1-32 characters). Default config...

  • Page 262: Revision (Mst)

    D-link des-3010fa/ga/pa cli reference guide page 261 revision (mst) the revision mst configuration command defines the configuration revision number. To return to the default con- figuration, use the no form of this command. Syntax revision value no revision parameters • value—configuration revision...

  • Page 264: Exit (Mst)

    D-link des-3010fa/ga/pa cli reference guide page 263 exit (mst) the exit mst configuration mode command exits the mst configuration mode and applies all configuration changes. Syntax exit default configuration this command has no default configuration. Command mode mst configuration mode user guidel...

  • Page 265: Abort (Mst)

    Spanning-tree commands page 264 abort (mst) the abort mst configuration mode command exits the mst configuration mode without applying the configura- tion changes. Syntax abort default configuration this command has no default configuration. Command mode mst configuration mode user guidelines there ...

  • Page 267

    Spanning-tree commands page 266 console# show spanning-tree spanning tree disabled (bpdu flooding) mode stp default port cost method: short root id priority 32768 address 00:19:28:37:46:00 this switch is the root hello time 2 sec max age 20 sec forward delay 15 sec number of topology changes 0 last ...

  • Page 268: Section 23. Syslog Commands

    D-link des-3010fa/ga/pa cli reference guide page 267 section 23. Syslog commands logging on the logging on global configuration mode command controls error message logging. This command sends debug or error messages to a logging process, which logs messages to designated locations asynchronously to ...

  • Page 270: Logging Console

    D-link des-3010fa/ga/pa cli reference guide page 269 logging console the logging console global configuration mode command limits messages logged to the console based on severity. To disable logging to the console, use the no form of this command. Syntax logging console level no logging console para...

  • Page 271: Logging Buffered

    Syslog commands page 270 logging buffered the logging buffered global configuration mode command limits syslog messages displayed from an internal buffer based on severity. To cancel using the buffer, use the no form of this command. Syntax logging buffered level no logging buffered parameters • lev...

  • Page 272: Logging Buffered Size

    D-link des-3010fa/ga/pa cli reference guide page 271 logging buffered size the logging buffered size global configuration mode command changes the number of syslog messages stored in the internal buffer. To return to the default configuration, use the no form of this command. Syntax logging buffered...

  • Page 273: Clear Logging

    Syslog commands page 272 clear logging the clear logging privileged exec mode command clears messages from the internal logging buffer. Syntax clear logging default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidelines...

  • Page 274: Logging File

    D-link des-3010fa/ga/pa cli reference guide page 273 logging file the logging file global configuration mode command limits syslog messages sent to the logging file based on severity. To cancel using the buffer, use the no form of this command. Syntax logging file level no logging file parameters • ...

  • Page 275: Clear Logging File

    Syslog commands page 274 clear logging file the clear logging file privileged exec mode command clears messages from the logging file. Syntax clear logging file default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no user guidel...

  • Page 276: Aaa Logging

    D-link des-3010fa/ga/pa cli reference guide page 275 aaa logging the aaa logging global configuration mode command enables logging aaa login events. To disable logging aaa login events, use the no form of this command. Syntax aaa logging login no aaa logging login parameters • login — indicates logg...

  • Page 277: File-System Logging

    Syslog commands page 276 file-system logging the file-system logging global configuration mode command enables logging file system events. To disable log- ging file system events, use the no form of this command. Syntax file-system logging copy no file-system logging copy parameters • copy — indicat...

  • Page 278: Management Logging

    D-link des-3010fa/ga/pa cli reference guide page 277 management logging the management logging global configuration command enables logging management access list (acl) events. To disable logging management access list events, use the no form of this command. Syntax management logging deny no manage...

  • Page 279: Show Logging

    Syslog commands page 278 show logging the show logging privileged exec mode command displays the state of logging and the syslog messages stored in the internal buffer. Syntax show logging default configuration this command has no default configuration. Command mode privileged exec mode user guideli...

  • Page 280

    D-link des-3010fa/ga/pa cli reference guide page 279 11-aug-2004 15:41:43: %link-3-updown: interface ethernet2, changed state to up 11-aug-2004 15:41:43: %link-3-updown: interface ethernet, changed state to up 11-aug-2004 15:41:43: %sys-5-config_i: configured from memory by console 11-aug-2004 15:41...

  • Page 281: Show Logging File

    Syslog commands page 280 show logging file the show logging file privileged exec mode command displays the state of logging and the syslog messages stored in the logging file. Syntax show logging file default configuration this command has no default configuration. Command mode privileged exec mode ...

  • Page 282

    D-link des-3010fa/ga/pa cli reference guide page 281 11-aug-2004 15:41:43: %link-3-updown: interface ethernet2, changed state to up 11-aug-2004 15:41:43: %link-3-updown: interface ethernet3, changed state to up 11-aug-2004 15:41:43: %sys-5-config_i: configured from memory by console 11-aug-2004 15:4...

  • Page 283: Show Syslog-Servers

    Syslog commands page 282 show syslog-servers the show syslog-servers privileged exec mode command displays the settings of the syslog servers. Syntax show syslog-servers default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no us...

  • Page 284: Section 24. User Interface

    D-link des-3010fa/ga/pa cli reference guide page 283 section 24. User interface enable the enable user exec mode command enters the privileged exec mode. Syntax enable [privilege-level] parameters • privilege-level — privilege level to enter the system. (range: 1 - 15) default configuration the defa...

  • Page 285: Disable

    User interface page 284 disable the disable privileged exec mode command returns to the user exec mode. Syntax disable [privilege-level] parameters • privilege-level — privilege level to enter the system. (range: 1 - 15) default configuration the default privilege level is 1. Command mode privileged...

  • Page 286: Login

    D-link des-3010fa/ga/pa cli reference guide page 285 login the login user exec mode command changes a login username. Syntax login default configuration this command has no default configuration. Command mode user exec mode user guidelines there are no user guidelines for this command. Example the f...

  • Page 287: Configure

    User interface page 286 configure the configure privileged exec mode command enters the global configuration mode. Syntax configure default configuration this command has no default configuration. Command mode privilegedexec mode user guidelines there are no user guidelines for this command. Example...

  • Page 288: Exit (Configuration)

    D-link des-3010fa/ga/pa cli reference guide page 287 exit (configuration) the exit command exits any configuration mode to the next highest mode in the cli mode hierarchy. Syntax exit default configuration this command has no default configuration. Command mode all configuration modes user guideline...

  • Page 289: Exit

    User interface page 288 exit the exit privileged/user exec mode command closes an active terminal session by logging off the device. Syntax exit default configuration this command has no default configuration. Command mode privileged and user exec modes user guidelines there are no user guidelines f...

  • Page 290: End

    D-link des-3010fa/ga/pa cli reference guide page 289 end the end command ends the current configuration session and returns to the privileged exec mode. Syntax end default configuration this command has no default configuration. Command mode all configuration modes. User guidelines there are no user...

  • Page 291: Help

    User interface page 290 help the help command displays a brief description of the help system. Syntax help default configuration this command has no default configuration. Command mode all command modes user guidelines there are no user guidelines for this command. Example the following example desc...

  • Page 292: Terminal Data-Dump

    D-link des-3010fa/ga/pa cli reference guide page 291 terminal data-dump the terminal data-dump user or privileged exec mode command enables dumping all the output of a show command without prompting. To disable dumping, use the no form of this command. Syntax terminal data-dump no terminal data-dump...

  • Page 293: Show History

    User interface page 292 show history the show history user or privileged exec mode command lists the commands entered in the current session. Syntax show history default configuration this command has no default configuration. Command mode user or privileged exec mode user guidelines user guidelines...

  • Page 294: Show Privilege

    D-link des-3010fa/ga/pa cli reference guide page 293 show privilege the show privilege privileged/user exec mode command displays the current privilege level. Syntax show privilege default configuration this command has no default configuration. Command mode privileged and user exec modes user guide...

  • Page 295: Section 25. Vlan Commands

    Vlan commands page 294 section 25. Vlan commands vlan database the vlan database global configuration mode command enters the vlan configuration mode. Syntax vlan database default configuration this command has no default configuration. Command mode global configuration mode user guidelines there ar...

  • Page 296: Vlan

    D-link des-3010fa/ga/pa cli reference guide page 295 vlan use the vlan vlan database mode command to create a vlan. To delete a vlan, use the no form of this com- mand. Syntax vlan vlan-range no vlan vlan-range parameters • vlan-range — specifies a list of vlan ids to be added. Separate nonconsecuti...

  • Page 297: Interface Vlan

    Vlan commands page 296 interface vlan the interface vlan global configuration mode command enters the interface configuration (vlan) mode. Syntax interface vlan vlan-id parameters • vlan-id — specifies an existing vlan id. Default configuration this command has no default configuration. Command mode...

  • Page 299: Name

    Vlan commands page 298 name the name interface configuration mode command adds a name to a vlan. To remove the vlan name, use the no form of this command. Syntax name string no name parameters • string — unique name to be associated with this vlan. (range: 1-32 characters) default configuration no n...

  • Page 300: Private-Vlan Primary

    D-link des-3010fa/ga/pa cli reference guide page 299 private-vlan primary the private-vlan primary interface configuration (vlan) mode command configures the primary pvlan. To return to the default configuration, use the no form of this command. Syntax private-vlan primary no private-vlan primary de...

  • Page 301: Private-Vlan Isolated

    Vlan commands page 300 private-vlan isolated the private-vlan isolated interface configuration (vlan) mode command configures the isolated vlan of the pvlan. To return to the default configuration, use the no form of this command. Syntax private-vlan isolated vlan-id no private-vlan isolated paramet...

  • Page 304: Switchport Access Vlan

    D-link des-3010fa/ga/pa cli reference guide page 303 switchport access vlan the switchport access vlan interface configuration mode command configures the vlan id when the interface is in access mode. To return to the default configuration, use the no form of this command. Syntax switchport access v...

  • Page 305: Switchport Private-Vlan

    Vlan commands page 304 switchport private-vlan the switchport private-vlan interface configuration command configures private-vlan port vlans. To return to the default configuration, use the no form of this command. Syntax switchport private-vlan promiscuous pvlan no switchport private-vlan promiscu...

  • Page 306: Show Vlan Private-Vlan

    D-link des-3010fa/ga/pa cli reference guide page 305 show vlan private-vlan the show vlan private-vlan privileged exec mode command displays information about private vlans. Syntax show vlan private-vlan [primary vlan-id] parameters • vlan-id— specifies the id of the primary vlan. Default configurat...

  • Page 308: Switchport Trunk Native Vlan

    D-link des-3010fa/ga/pa cli reference guide page 307 switchport trunk native vlan the switchport trunk native vlan interface configuration mode command defines the native vlan when the interface is in trunk mode. To return to the default configuration, use the no form of this command. Syntax switchp...

  • Page 310: Switchport General Pvid

    D-link des-3010fa/ga/pa cli reference guide page 309 switchport general pvid the switchport general pvid interface configuration mode command configures the pvid when the interface is in general mode. To return to the default configuration, use the no form of this command. Syntax switchport general ...

  • Page 311

    Vlan commands page 310 switchport general ingress-filtering disable the switchport general ingress-filtering disable interface configuration mode command disables port ingress filtering. To return to the default configuration, use the no form of this command. Syntax switchport general ingress-filter...

  • Page 312

    D-link des-3010fa/ga/pa cli reference guide page 311 switchport general acceptable-frame-type tagged-only the switchport general acceptable-frame-type tagged-only interface configuration mode command discards untagged frames at ingress. To return to the default configuration, use the no form of this...

  • Page 314: Ip Internal-Usage-Vlan

    D-link des-3010fa/ga/pa cli reference guide page 313 ip internal-usage-vlan the ip internal-usage-vlan interface configuration mode command reserves a vlan as the internal usage vlan of an interface. To return to the default configuration, use the no form of this command. Syntax ip internal-usage-vl...

  • Page 316: Show Vlan Internal Usage

    D-link des-3010fa/ga/pa cli reference guide page 315 show vlan internal usage the show vlan internal usage privileged exec mode command displays a list of vlans used internally by the device. Syntax show vlan internal usage default configuration this command has no default configuration. Command mod...

  • Page 318

    D-link des-3010fa/ga/pa cli reference guide page 317.

  • Page 319: Section 26. Web Server

    Web server page 318 section 26. Web server ip http server the ip http server global configuration mode command enables configuring the device from a browser. To dis- able this function, use the no form of this command. Syntax ip http server no ip http server default configuration http server is enab...

  • Page 320: Ip Https Server

    D-link des-3010fa/ga/pa cli reference guide page 319 ip https server the ip https server global configuration mode command enables configuring the device from a browser. To dis- able this function, use the no form of this command. Syntax ip https server no ip https server default configuration https...

  • Page 321: Ip Http Exec-Timeout

    Web server page 320 ip http exec-timeout the ip http exec-timeout global configuration command sets the interval in which the system waits for the user input in http sessions before automatic logoff, use the ip http exec-timeout global configuration command. To return to default, use the no form of ...

  • Page 322: Ip Https Certificate

    D-link des-3010fa/ga/pa cli reference guide page 321 ip https certificate the ip https certificate global configuration mode command enables configuring the active certificate for https. To disable this function, use the no form of this command. Syntax ip https certificate number no ip https certifi...

  • Page 323: Show Ip Https

    Web server page 322 show ip https the show ip https global configuration mode command displays the configuration of the https server. Syntax show ip https default configuration this command has no default setting. Command mode privileged exec user guidelines there are no user guidelines for this com...

  • Page 324: Crypto Certificate Generate

    D-link des-3010fa/ga/pa cli reference guide page 323 crypto certificate generate the crypto certificate generate global configuration mode command generates self signed certificate for https . Syntax crypto certificate number generate [key-generate [length]] [passphrase string] [cn common- name] [ou...

  • Page 325: Crypto Certificate Import

    Web server page 324 crypto certificate import the crypto certificate import global configuration mode command enables to import a certificate signed by cer- tification authority for https. Syntax crypto certificate number import parameters number - specifies the certificate number. (range: 1-2) defa...

  • Page 326

    D-link des-3010fa/ga/pa cli reference guide page 325 example the following example enables configuring the device from a browser. Console(config)# crypto certificate 1 import -----begin certificate----- dhmugum9vdcbdzxj0awzpzxiwxdanbgkqhkig9w0baqefaanladbiakeap4hs nnh/xqsga2ffkrbwu2xixb7n8vpstm1xyj1...

  • Page 327

    Web server page 326 show crypto certificate mycertificate the show crypto certificate mycertificate global configuration mode command enables to view ssl certifi- cates of the device. Syntax show crypto certificate mycertificate [number] parameters • number - specifies the certificate number. (range...

  • Page 328: Ip Http Port

    D-link des-3010fa/ga/pa cli reference guide page 327 ip http port syntax ip http port port-number no ip http port parameters • port-number — port number for use by the http server. (range: 1 - 65535) default configuration the default port number is 80. Command mode global configuration mode example ...

  • Page 329: Ip Https Port

    Web server page 328 ip https port the ip https port global configuration mode command specifies the tcp port to be used by the web browser interface. To return to the default configuration, use the no form of this command. Syntax ip https port port-number no ip https port parameters • port-number — ...

  • Page 330: Show Ip Http

    D-link des-3010fa/ga/pa cli reference guide page 329 show ip http the show ip http privileged exec mode command displays the http server configuration. Syntax show ip http default configuration this command has no default configuration. Command mode privileged exec mode user guidelines there are no ...

  • Page 331: Section 27. 802.1X Commands

    802.1x commands page 330 section 27. 802.1x commands aaa authentication dot1x the aaa authentication dot1x global configuration mode command specifies one or more authentication, autho- rization, and accounting (aaa) methods for use on interfaces running ieee 802.1x. To return to the default config-...

  • Page 332: Dot1X System-Auth-Control

    D-link des-3010fa/ga/pa cli reference guide page 331 dot1x system-auth-control the dot1x system-auth-control global configuration mode command enables 802.1x globally. To return to the default configuration, use the no form of this command. Syntax dot1x system-auth-control no dot1x system-auth-contr...

  • Page 334: Dot1X Re-Authentication

    D-link des-3010fa/ga/pa cli reference guide page 333 dot1x re-authentication the dot1x re-authentication interface configuration mode command enables periodic re-authentication of the client. To return to the default configuration, use the no form of this command. Syntax dot1x re-authentication no d...

  • Page 335: Dot1X Timeout Re-Authperiod

    802.1x commands page 334 dot1x timeout re-authperiod the dot1x timeout re-authperiod interface configuration mode command sets the number of seconds between re-authentication attempts. To return to the default configuration, use the no form of this command. Syntax dot1x timeout re-authperiod seconds...

  • Page 336: Dot1X Re-Authenticate

    D-link des-3010fa/ga/pa cli reference guide page 335 dot1x re-authenticate the dot1x re-authenticate privileged exec mode command manually initiates a re-authentication of all 802.1x- enabled ports or the specified 802.1x-enabled port. Syntax dot1x re-authenticate [ethernet interface] parameters • i...

  • Page 337: Dot1X Timeout Quiet-Period

    802.1x commands page 336 dot1x timeout quiet-period the dot1x timeout quiet-period interface configuration mode command sets the number of seconds that the device remains in the quiet state following a failed authentication exchange (for example, the client provided an invalid password). To return t...

  • Page 338: Dot1X Timeout Tx-Period

    D-link des-3010fa/ga/pa cli reference guide page 337 dot1x timeout tx-period the dot1x timeout tx-period interface configuration mode command sets the number of seconds that the device waits for a response to an extensible authentication protocol (eap)-request/identity frame from the client before r...

  • Page 339: Dot1X Max-Req

    802.1x commands page 338 dot1x max-req the dot1x max-req interface configuration mode command sets the maximum number of times that the device sends an extensible authentication protocol (eap)-request/identity frame (assuming that no response is received) to the client, before restarting the authent...

  • Page 340: Dot1X Timeout Supp-Timeout

    D-link des-3010fa/ga/pa cli reference guide page 339 dot1x timeout supp-timeout the dot1x timeout supp-timeout interface configuration mode command sets the time for the retransmission of an extensible authentication protocol (eap)-request frame to the client. To return to the default configuration,...

  • Page 341: Dot1X Timeout Server-Timeout

    802.1x commands page 340 dot1x timeout server-timeout the dot1x timeout server-timeout interface configuration mode command sets the time that the device waits for a response from the authentication server. To return to the default configuration, use the no form of this command. Syntax dot1x timeout...

  • Page 342: Show Dot1X

    D-link des-3010fa/ga/pa cli reference guide page 341 show dot1x the show dot1x privileged or user exec mode command displays the 802.1x status of the device or specified interface. Syntax show dot1x [ethernet interface] parameters • interface — valid ethernet port. (full syntax: port) default config...

  • Page 343

    802.1x commands page 342 the following table describes significant fields shown above: port admin mode oper mode reauth control reauth period username ---- ---------- --------- ------- ------ -------- 3 auto unauthorized ena 3600 clark quiet period: 60 seconds tx period:30 seconds max req: 2 supplic...

  • Page 344

    D-link des-3010fa/ga/pa cli reference guide page 343 max req the maximum number of times that the device sends an extensible authentica- tion protocol (eap)-request frame (assuming that no response is received) to the client before restarting the authentication process. Supplicant timeout time in se...

  • Page 345: Show Dot1X Users

    802.1x commands page 344 show dot1x users the show dot1x users privileged or user exec mode command displays active 802.1x authenticated users for the device. Syntax show dot1x users [username username] parameters • username — supplicantusername (range: 1-160 characters) default configuration this c...

  • Page 346

    D-link des-3010fa/ga/pa cli reference guide page 345 the following table describes significant fields shown above: field description port the port number. Username the username representing the identity of the supplicant. Session time the period of time the supplicant is connected to the system. Aut...

  • Page 347: Show Dot1X Statistics

    802.1x commands page 346 show dot1x statistics the show dot1x statistics privileged or user exec mode command displays 802.1x statistics for the specified interface. Syntax show dot1x statistics ethernet interface parameters • interface — valid ethernet port. (full syntax: port) default configuratio...

  • Page 348

    D-link des-3010fa/ga/pa cli reference guide page 347 the following table describes the significant fields shown in the display: field description eapolframesrx the number of valid eapol frames of any type that have been received by this authenticator. Eapolframestx the number of eapol frames of any ...

  • Page 349: Advanced Features

    802.1x commands page 348 advanced features dot1x auth-not-req the dot1x auth-not-req interface configuration (vlan) mode command enables unauthorized devices access to the vlan. To disable access to the vlan, use the no form of this command. Syntax dot1x auth-not-req no dot1x auth-not-req default co...

  • Page 350: Dot1X Multiple-Hosts

    D-link des-3010fa/ga/pa cli reference guide page 349 dot1x multiple-hosts the dot1x multiple-hosts interface configuration mode command enables multiple hosts (clients) on an 802.1x- authorized port, where the authorization state of the port is set to auto. To return to the default configuration, us...

  • Page 351: Dot1X Single-Host-Violation

    802.1x commands page 350 dot1x single-host-violation the dot1x single-host-violation interface configuration mode command configures the action to be taken, when a station whose mac address is not the supplicant mac address, attempts to access the interface. Use the no form of this command to return...

  • Page 352: Dot1X Guest-Vlan

    D-link des-3010fa/ga/pa cli reference guide page 351 dot1x guest-vlan the dot1x guest-vlan interface configuration (vlan) mode command defines a guest vlan. To return to the default configuration, use the no form of this command. Syntax dot1x guest-vlan no dot1x guest-vlan default configuration no v...

  • Page 353: Dot1X Guest-Vlan Enable

    802.1x commands page 352 dot1x guest-vlan enable the dot1x vlans guest-vlan enable interface configuration mode command enables unauthorized users on the interface access to the guest vlan. To disable access, use the no form of this command syntax dot1x guest-vlan enable no dot1x guest-vlan enable d...

  • Page 354: Show Dot1X Advanced

    D-link des-3010fa/ga/pa cli reference guide page 353 show dot1x advanced the show dot1x advanced privileged exec mode command displays 802.1x advanced features for the device or specified interface. Syntax show dot1x advanced [ethernet interface] parameters • interface — valid ethernet port. (full s...

  • Page 355

    802.1x commands page 354 trap frequency: 100 status: single-host locked violations since last trap: 9.

  • Page 356: Troubleshooting

    D-link des-3010fa/ga/pa cli reference guide page 355 troubleshooting this section describes problems that may arise when installing the device and how to resolve these issues. This section includes the following topics: • problem management — provides information about problem management with des-30...

  • Page 357

    Page 356 problems possible cause solution cannot connect to manage- ment using rs-232 serial connection be sure the terminal emulator program is set to vt-100 compatible, 9600 baud rate, no parity, 8 data bits and one stop bit use the included cable, or be sure that the pin-out complies with a stand...

  • Page 358

    D-link des-3010fa/ga/pa cli reference guide page 357 no connection and the port led is off incorrect ethernet cable, e.G., crossed rather than straight cable, or vice versa, split pair (incorrect twisting of pairs) fiber optical cable connec- tion is reversed bad cable wrong cable type check pinout ...

  • Page 359

    Page 358 add and edit pages do not open. A pop-up blocker is enabled. Disable pop-up blockers. Lost password the password recovery procedure enables the user to set the password back to the default setting. The password recovery procedure is invoked from the startup menu: 1. Reboot the system either...

  • Page 360

    D-link des-3010fa/ga/pa cli reference guide page 359 international offices u.S.A 17595 mt. Herrmann street fountain valley, ca. 92708 tel: 714-885-6000 fax 866-743-4905 url: www.Dlink.Com canada 2180 winston park drive oakville, ontario, l6h 5w1 canada tel: 1-905-8295033 fax: 1-905-8295223 url: www....

  • Page 361

    International offices page 360