1. DL manuals
  2. D-Link
  3. Switch
  4. DES-3326S - Switch - Stackable
  5. Command Line Interface Reference Manual

D-Link DES-3326S - Switch - Stackable Command Line Interface Reference Manual - Fcc Warning

Other manuals for DES-3326S - Switch - Stackable: User Manual, Command Line Interface Reference Manual
Manual is about: Layer 3 Switch

Summary of DES-3326S - Switch - Stackable

  • Page 1

    I des-3326sr layer 3 switch command line interface reference manual (april 2003) des3326sr … 1 printed in taiwan recyclable.

  • Page 2: Wichtige Sicherheitshinweise

    Ii wichtige sicherheitshinweise 1. Bitte lesen sie sich diese hinweise sorgfä ltig durch. 2. Heben sie diese anleitung für den spä tern gebrauch auf. 3. Vor jedem reinigen ist das gerä t vom stromnetz zu trennen. Vervenden sie keine flüssig- oder aerosolreiniger. Am besten dient ein angefeuchtetes t...

  • Page 3: Warranties Exclusive

    Iii warranties exclusive if the d-link product does not operate as warranted above, the customer's sole remedy shall be, at d-link's option, repair or replacement. The foregoing warranties and remedies are exclusive and are in lieu of all other warranties, expressed or implied, either in fact or by ...

  • Page 4: Software:

    Iv warranty service may be obtained by contacting a d-link office within the applicable warranty period, and requesting a return material authorization (rma) number. If a registration card for the product in question has not been returned to d-link, then a proof of purchase (such as a copy of the da...

  • Page 5: Trademarks

    V d-link offices for registration and warranty service the product's registration card, provided at the back of this manual, must be sent to a d-link office. To obtain an rma number for warranty service as to a hardware product, or to obtain warranty service as to a software product, contact the d-l...

  • Page 6: Fcc Warning

    Vi fcc warning this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Th...

  • Page 7

    Vii table of contents introduction ................................ ................................ .............. 9 using the console cli................................ .............................. 13 command syntax ................................ ................................ .... 19 basic...

  • Page 8

    Viii routing table commands ................................ ....................... 215 route redistribution commands................................ .............220 igmp commands................................ ................................ ....233 igmp snooping commands..........................

  • Page 9: Ntroduction

    Des-3326sr layer 3 fast ethernet switch cli reference manual introduction 9 1 i ntroduction the switch can be managed through the switch’s serial port, telnet, or the web-based management agent. The command line interface (cli) can be used to configure and manage the switch via the serial port or te...

  • Page 10: Setting The Switch

    Des-3326sr layer 3 fast ethernet switch cli reference manual 10 introduction fig. 1- 1. Initial console screen. There is no initial username or password. Just press the enter key twice to display the cli input cursor − des-3326sr:4#. This is the command line where all commands are input. Setting the...

  • Page 11

    Des-3326sr layer 3 fast ethernet switch cli reference manual introduction 11 the switch’s mac address can also be found from the web management program on the switch information (basic settings) window on the configuration menu. The ip address for the switch must be set before it can be managed with...

  • Page 12

    Des-3326sr layer 3 fast ethernet switch cli reference manual 12 introduction fig. 1- 4. Assigning the switch an ip address in the above example, the switch was assigned an ip address of 10.52.19.7 with a subnet mask of 255.0.0.0. The system message success indicates that the command was executed suc...

  • Page 13: Sing The

    Des-3326sr layer 3 fast ethernet switch cli reference manual using the console cli 13 2 u sing the c onsole cli the des-3326sr supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer running a terminal em...

  • Page 14

    Des-3326sr layer 3 fast ethernet switch cli reference manual 14 using the console cli • vt-100/ansi compatible • 9,600 baud • 8 data bits • no parity • one stop bit • no flow control you can also access the same functions over a telnet interface. Once you have set an ip address for your switch, you ...

  • Page 15

    Des-3326sr layer 3 fast ethernet switch cli reference manual using the console cli 15 fig. 2- 2. The ? Command the dir command has the same function as the ? Command. When you enter a command without its required parameters, the cli will prompt you with a next possible completions: message. Fig. 2- ...

  • Page 16

    Des-3326sr layer 3 fast ethernet switch cli reference manual 16 using the console cli in addition, after typing any given command plus one space, you can see all of the next possible sub-commands, in sequential order, by repeatedly pressing the tab key. To re-enter the previous command at the comman...

  • Page 17

    Des-3326sr layer 3 fast ethernet switch cli reference manual using the console cli 17 fig. 2- 5. The next available commands prompt the top-level commands consist of commands like show or config. Most of these commands require one or more parameters to narrow the top-level command. This is equivalen...

  • Page 18

    Des-3326sr layer 3 fast ethernet switch cli reference manual 18 using the console cli in the above example, all of the possible next parameters for the show command are displayed. At the next command prompt, the up arrow was used to re-enter the show command, followed by the account parameter. The c...

  • Page 19: Ommand

    Des-3326sr layer 3 fast ethernet switch cli reference manual command syntax 19 3 c ommand s yntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available through the console inte...

  • Page 20

    Des-3326sr layer 3 fast ethernet switch cli reference manual 20 command syntax [square brackets] purpose encloses a required value or set of required arguments. One or more values or arguments can be specified. Syntax create account [admin/user] description in the above syntax example, you must spec...

  • Page 21

    Des-3326sr layer 3 fast ethernet switch cli reference manual command syntax 21 / slash command {braces} purpose encloses an optional value or set of optional arguments. Syntax config igmp [/all] {version /query_interval /max_response_time / robustness_variable /last_member_query_interval /state [ena...

  • Page 22

    Des-3326sr layer 3 fast ethernet switch cli reference manual 22 command syntax line editing key usage delete in certain formats, deletes highlighted characters and then shifts the remaining characters in the line to the left. Backspace deletes the character to the left of the cursor and shifts the r...

  • Page 23

    Des-3326sr layer 3 fast ethernet switch cli reference manual command syntax 23 line editing key usage p displays the previous page. Q stops the display of remaining pages when multiple pages are to be displayed. R refreshes the pages currently displaying. A displays the remaining pages without pausi...

  • Page 24: Asic

    Des-3326sr layer 3 fast ethernet switch cli reference manual 24 basic switch commands 4 b asic s witch c ommands the basic switch commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create account [admin/user] con...

  • Page 25

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 25 create account purpose used to create user accounts syntax create [admin/user] description the create account command is used to create user accounts that consist of a username of 1 to 15 characters and a password ...

  • Page 26

    Des-3326sr layer 3 fast ethernet switch cli reference manual 26 basic switch commands config account purpose used to configure user accounts syntax config account description the config account command configures a user account that has been created using the create account command. Parameters restr...

  • Page 27

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 27 show account purpose used to display user accounts syntax show account description displays all user accounts created on the switch. Up to 8 user accounts can exist on the switch at one time. Parameters none. Restr...

  • Page 28

    Des-3326sr layer 3 fast ethernet switch cli reference manual 28 basic switch commands delete account purpose used to delete an existing user account syntax delete account description the delete account command deletes a user account that has been created using the create account command. Parameters ...

  • Page 29

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 29 show session purpose used to display a list of currently logged-in users. Syntax show session description this command displays a list of all the users that are logged-in at the time the command is issued. Paramete...

  • Page 30

    Des-3326sr layer 3 fast ethernet switch cli reference manual 30 basic switch commands show switch purpose used to display information about the switch. Syntax show switch description this command displays information about the switch. Parameters none. Restrictions none. Example usage: to display the...

  • Page 31

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 31 spanning tree : disabled gvrp : disabled igmp snooping : disabled telnet : enabled (tcp 23) web : enabled (tcp 80) rmon : disabled des-3326sr:4#.

  • Page 32

    Des-3326sr layer 3 fast ethernet switch cli reference manual 32 basic switch commands show serial_port purpose used to display the current serial port settings. Syntax show serial_port description this command displays the current serial port settings. Parameters none. Restrictions none example usag...

  • Page 33

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 33 config serial_port purpose used to configure the serial port. Syntax config serial_port {baud_rate[9600/19200/38400/115200]/auto_ logout [never/2_minutes/5_minutes/10_minutes/ 15_minutes]} description this command ...

  • Page 34

    Des-3326sr layer 3 fast ethernet switch cli reference manual 34 basic switch commands example usage: to configure baud rate: des-3326sr:4#config serial_port baud_rate 9600 command: config serial_port baud_rate 9600 success. Des-3326sr:4#.

  • Page 35

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 35 enable clipaging purpose used to pause the scrolling of the console screen when the show command displays more than one page. Syntax enable clipaging description this command is used when issuing the show command w...

  • Page 36

    Des-3326sr layer 3 fast ethernet switch cli reference manual 36 basic switch commands disable clipaging purpose used to disable the pausing of the console screen scrolling at the end of each page when the show command would display more than one screen of information. Syntax disable clipaging descri...

  • Page 37

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 37 enable telnet purpose used to enable communication with and management of the switch using the telnet protocol. Syntax enable telnet description this command is used to enable the telnet protocol on the switch. The...

  • Page 38

    Des-3326sr layer 3 fast ethernet switch cli reference manual 38 basic switch commands disable telnet purpose used to disable the telnet protocol on the switch. Syntax disable telnet description this command is used to disable the telnet protocol on the switch. Parameters none. Restrictions only admi...

  • Page 39

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 39 enable web purpose used to enable the http-based management software on the switch. Syntax enable web description this command is used to enable the web- based management software on the switch. The user can specif...

  • Page 40

    Des-3326sr layer 3 fast ethernet switch cli reference manual 40 basic switch commands disable web purpose used to disable the http-based management software on the switch. Syntax disable web description this command disables the web-based management software on the switch. Parameters none. Restricti...

  • Page 41

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 41 save purpose used to save changes in the switch’s configuration to non-volatile ram. Syntax save description this command is used to enter the current switch configuration into non-volatile ram. The saved switch co...

  • Page 42

    Des-3326sr layer 3 fast ethernet switch cli reference manual 42 basic switch commands reboot purpose used to restart the switch. Syntax reboot description this command is used to restart the switch. Parameters none. Restrictions none. Example usage: to restart the switch: des-3326sr:4#reboot command...

  • Page 43

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 43 reset purpose used to reset the switch to the factory default settings. Syntax reset {config/system} description this command is used to restore the switch’s configuration to the default settings assigned from the ...

  • Page 44

    Des-3326sr layer 3 fast ethernet switch cli reference manual 44 basic switch commands des-3326sr:4#reset config command: reset config success. Des-3326sr:4# login purpose used to log in a user to the switch’s console. Syntax login description this command is used to initiate the login procedure. The...

  • Page 45

    Des-3326sr layer 3 fast ethernet switch cli reference manual basic switch commands 45 logout purpose used to log out a user from the switch’s console. Syntax logout description this command terminates the current user’s session on the switch’s console. Parameters none. Restrictions none. Example usa...

  • Page 46: Witch

    Des-3326sr layer 3 fast ethernet switch cli reference manual 46 switch port commands 5 s witch p ort c ommands the switch port commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config ports speed [auto/10_half/1...

  • Page 47

    Des-3326sr layer 3 fast ethernet switch cli reference manual switch port commands 47 config ports purpose used to configure the switch’s ethernet port settings. Syntax config ports [] {speed[auto/10_half/10_full/100_half/100_hal f/1000_full] learning [enabled/disabled] state [enabled/disabled]} desc...

  • Page 48

    Des-3326sr layer 3 fast ethernet switch cli reference manual 48 switch port commands config ports the mac address learning on the specified range of ports. State [enabled/disabled] − enables or disables the specified range of ports. Restrictions only administrator-level users can issue this command....

  • Page 49

    Des-3326sr layer 3 fast ethernet switch cli reference manual switch port commands 49 config port_security purpose used to configure port lock settings. Syntax config port_security /all admin_state [enabled/disaled] max_learning_addr lock_address_mode [deleteontimout/deleteonreset] description this c...

  • Page 50

    Des-3326sr layer 3 fast ethernet switch cli reference manual 50 switch port commands config port_security number of mac addresses dynamically listed in the fdb for the ports. Lock_address_mode[deleteontimout/deleteonre set] – delete fdb dynamic entries for the ports on timeout of the fdb (see forwar...

  • Page 51

    Des-3326sr layer 3 fast ethernet switch cli reference manual switch port commands 51 show ports purpose used to display the current configuration of a range of ports. Syntax show ports {} description this command is used to display the current configuration of a range of ports. Parameters − specifie...

  • Page 52

    Des-3326sr layer 3 fast ethernet switch cli reference manual 52 switch port commands 5 enabled auto link down enabl ed 6 enabled auto link down enabled 7 enabled auto link down enabled show port_security purpose used to display the current portr lock configuration. Syntax show port_security {} descr...

  • Page 53

    Des-3326sr layer 3 fast ethernet switch cli reference manual switch port commands 53 example usage: to display the port lock configuration: des-3326sr:4#show port_security command: show port_security port# admin state max. Learning addr. Lock address mode ---- ----------- ------------------- -------...

  • Page 54: Etwork

    Des-3326sr layer 3 fast ethernet switch cli reference manual 54 network management commands 6 n etwork m anagement c ommands the network management commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. The des-3326sr supports the simp...

  • Page 55

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 55 command parameters create snmp user v1/v2c/v3 encrypted auth [md5/sha] priv [none/des delete snmp user show snmp user show snmp groups create snmp view view_type [included/excluded] delete snmp view [all/oid]...

  • Page 56

    Des-3326sr layer 3 fast ethernet switch cli reference manual 56 network management commands notify_view delete snmp group create snmp host v1/v2c/v3 noauth_nopriv auth_nopriv auth_priv delete snmp host show snmp host enable rmon disable rmon ping times timeout traceroute port timeout probe config ma...

  • Page 57

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 57 create snmp user purpose used to create a new snmp user and adds the user to an snmp group that is also created by this command. Syntax create snmp user [v1/v2c/v3 {encrypted auth [md5/sha] priv [none/des ]}]...

  • Page 58

    Des-3326sr layer 3 fast ethernet switch cli reference manual 58 network management commands create snmp user v3 – specifies that the snmp version 3 will be used. Snmp v3 provides secure access to devices through a combination of authentication and encrypting packets over the network. Snmp v3 adds: •...

  • Page 59

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 59 create snmp user host sends to the agent. Restrictions only administrator-level users can issue this command. Example usage: to create an snmp user on the switch: des-3326sr:4#create snmp user dlink default v...

  • Page 60

    Des-3326sr layer 3 fast ethernet switch cli reference manual 60 network management commands delete snmp user purpose used to remove an snmp user from an snmp group and also to delete the associated snmp group. Syntax delete snmp user description the delete snmp user command removes an snmp user from...

  • Page 61

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 61 show snmp user purpose used to display information about each snmp username in the snmp group username table. Syntax show snmp user description the show snmp user command displays information about each snmp ...

  • Page 62

    Des-3326sr layer 3 fast ethernet switch cli reference manual 62 network management commands show snmp groups purpose used to display the group-names of snmp groups currently configured on the switch. The security model, level, and status of each group is also displayed. Syntax show snmp groups descr...

  • Page 63

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 63 group name : group4 readview name : readview writeview name : writeview notify view name : notifyview securiy model : snmpv3 securiy level : authnopriv group name : group5 readview name : readview writeview n...

  • Page 64

    Des-3326sr layer 3 fast ethernet switch cli reference manual 64 network management commands notify view name : restricted securiy model : snmpv3 securiy level : noauthnopriv group name : readgroup readview name : communityview writeview name : notify view name : communityview securiy model : snmpv1 ...

  • Page 65

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 65 des-3326sr:4# create snmp view purpose used to assign views to community strings to limit which mib objects and snmp manager can access. Syntax create snmp view view_type [included/excluded] description the c...

  • Page 66

    Des-3326sr layer 3 fast ethernet switch cli reference manual 66 network management commands example usage: to create and snmp view: des-3326sr:4#create snmp view dlinkview 1.3.6 view_type included command: create snmp view dlinkview 1.3.6 view_type included success. Des-3326sr:4#.

  • Page 67

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 67 delete snmp view purpose used to remove an snmp view entry previously created on the switch. Syntax delete snmp view [all/] description the delete snmp view command is used to remove an snmp view previously c...

  • Page 68

    Des-3326sr layer 3 fast ethernet switch cli reference manual 68 network management commands show snmp view purpose used to display an snmp view previously created on the switch. Syntax show snmp view {} description the show snmp view command displays an snmp view previously created on the switch. Pa...

  • Page 69

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 69 restricted 1.3.6.1.6.3.15.1.1 included communityview 1 included communityview 1.3.6.1.6.3 excluded communityview .3.6.1.6.3.1 included total entries: 11 des-3326sr:4#.

  • Page 70

    Des-3326sr layer 3 fast ethernet switch cli reference manual 70 network management commands create snmp community purpose used to create an snmp community string to define the relationship between the snmp manager and an agent. The community string acts like a password to permit access to the agent ...

  • Page 71

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 71 create snmp community remote snmp managers access to mib objects in the switch’s snmp agent. − an alphanumeric string of up to 32 characters that is used to identify the group of mib objects that a remote snm...

  • Page 72

    Des-3326sr layer 3 fast ethernet switch cli reference manual 72 network management commands delete snmp community purpose used to remove a specific snmp community string from the switch. Syntax delete snmp community description the delete snmp community command is used to remove a previously defined...

  • Page 73

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 73 show snmp community purpose used to display snmp community strings configured on the switch. Syntax show snmp community {} description the show snmp community command is used to display snmp community strings...

  • Page 74

    Des-3326sr layer 3 fast ethernet switch cli reference manual 74 network management commands config snmp engineid purpose used to configure a name for the snmp engine on the switch. Syntax config snmp engineid description the config snmp engineid command configures a name for the snmp engine on the s...

  • Page 75

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 75 show snmp engineid purpose used to display the identification of the snmp engine on the switch. Syntax show snmp engineid description the show snmp engineid command displays the identification of the snmp eng...

  • Page 76

    Des-3326sr layer 3 fast ethernet switch cli reference manual 76 network management commands create snmp group purpose used to create a new snmp group, or a table that maps snmp users to snmp views. Syntax create snmp group [v1/v2c/v3 [noauth_nopriv/auth_nopriv/auth_priv]] {read_view /notify_view /no...

  • Page 77

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 77 create snmp group be used. Snmp v3 provides secure access to devices through a combination of authentication and encrypting packets over the network. Snmp v3 adds: • message integrity − ensures that packets h...

  • Page 78

    Des-3326sr layer 3 fast ethernet switch cli reference manual 78 network management commands create snmp group string of up to 32 characters that is used to identify the group of mib objects that a remote snmp manager is allowed to access on the switch. Notify_view − specifies that the snmp group bei...

  • Page 79

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 79 delete snmp group purpose used to remove an snmp group from the switch. Syntax delete snmp group description the delete snmp group command is used to remove an snmp group from the switch. Parameters − an alph...

  • Page 80

    Des-3326sr layer 3 fast ethernet switch cli reference manual 80 network management commands create snmp host purpose used to create a recipient of snmp traps generated by the switch’s snmp agent. Syntax create snmp host [v1/v2c/v3 [noauth_nopriv/auth_nopriv/auth_priv] ] description the create snmp h...

  • Page 81

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 81 create snmp host • message integrity − ensures that packets have not been tampered with in transit. • authentication − determines that an snmp message is from a valid source. • encryption − scrambles the cont...

  • Page 82

    Des-3326sr layer 3 fast ethernet switch cli reference manual 82 network management commands example usage: to create an snmp host to receive snmp messages: des-3326sr:4#create snmp host 10.48.74.100 v3 auth_priv public command: create snmp host 10.48.74.100 v3 auth_priv public success. Des-3326sr:4#.

  • Page 83

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 83 delete snmp host purpose used to remove a recipient of snmp traps generated by the switch’s snmp agent. Syntax delete snmp host description the delete snmp host command deletes a recipient of snmp traps gener...

  • Page 84

    Des-3326sr layer 3 fast ethernet switch cli reference manual 84 network management commands show snmp host purpose used to display the recipient of snmp traps generated by the switch’s snmp agent. Syntax show snmp host {} description the show snmp host command is used to display the ip addresses and...

  • Page 85

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 85 enable rmon purpose used to enable rmon on the switch. Syntax enable rmon description this command is used, in conjunction with the disable rmon command below, to enable and disable remote monitoring (rmon) o...

  • Page 86

    Des-3326sr layer 3 fast ethernet switch cli reference manual 86 network management commands disable rmon purpose used to disable rmon on the switch. Syntax disable rmon description this command is used, in conjunction with the enable rmon command above, to enable and disable remote monitoring (rmon)...

  • Page 87

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 87 ping purpose used to test the connectivity between network devices. Syntax ping {times } {timeout } description this command sends internet control message protocol (icmp) echo messages to a remote ip address...

  • Page 88

    Des-3326sr layer 3 fast ethernet switch cli reference manual 88 network management commands example usage: to send icmp echo message to “10.48.74.121” for 4 times: des-3326sr:4#ping 10.48.74.121 times 4 command: ping 10.48.74.121 reply from 10.48.74.121, time reply from 10.48.74.121, time reply from...

  • Page 89

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 89 traceroute purpose used to determine the network path between two devices. Syntax traceroute {ttl } {port } {timeout } {probe } description this command allows you to trace a route between the switch and a gi...

  • Page 90

    Des-3326sr layer 3 fast ethernet switch cli reference manual 90 network management commands trace the routed path between the switch and 10.48.74.121. Des-3326sr:4#traceroute 10.48.74.121 probe 3 command: traceroute 10.48.74.121 probe 3 1 1 1 des-3326sr:4# config mac_notification purpose used to con...

  • Page 91

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 91 config mac_notification number, and the highest port number of the range (also separeted by a colon) are specified. The beginning and end of the port list range are seperated by a dash. For example, 1:3 would...

  • Page 92

    Des-3326sr layer 3 fast ethernet switch cli reference manual 92 network management commands enable mac_notification purpose used to enable mac address notification while preserving current configuration. Syntax enable mac_notification description this command is used to enable mac address notificati...

  • Page 93

    Des-3326sr layer 3 fast ethernet switch cli reference manual network management commands 93 show mac_notification purpose to display the current mac notification settings of a range of ports. Syntax show mac_notification {} description this command is used to display the max notification settings of...

  • Page 94

    Des-3326sr layer 3 fast ethernet switch cli reference manual 94 network management commands.

  • Page 95: Ownload

    Des-3326sr layer 3 fast ethernet switch cli reference manual download/upload commands 95 7 d ownload /u pload c ommands the download/upload commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters download firmware uni...

  • Page 96

    Des-3326sr layer 3 fast ethernet switch cli reference manual 96 download/upload commands download purpose used to download and install new firmware or a switch configuration file from a tftp server. Syntax download [ firmware {unit [all/]}/configuration {increment}] description this command is used ...

  • Page 97

    Des-3326sr layer 3 fast ethernet switch cli reference manual download/upload commands 97 download parameters will remain unchanged. Restrictions the tftp server must be on the same ip subnet as the switch. Only administrator- level users can issue this command. Example usage: des-3326sr:4#download c...

  • Page 98

    Des-3326sr layer 3 fast ethernet switch cli reference manual 98 download/upload commands upload purpose used to upload the current switch settings or the switch history log to a tftp server. Syntax upload [configuration/log] description this command is used to upload either the switch’s current sett...

  • Page 99

    Des-3326sr layer 3 fast ethernet switch cli reference manual download/upload commands 99 example usage: des-3326sr:4#upload configuration 10.48.74.121 c:\cfg\log.Txt command: upload configuration 10.48.74.121 c:\cfg\log.Txt connecting to server................... Done. Upload configuration.............

  • Page 100: Etwork

    Des-3326sr layer 3 fast ethernet switch cli reference manual 100 network monitoring commands 8 n etwork m onitoring c ommands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show packet ...

  • Page 101

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 101 command parameters local7 udp_port ipaddress state [enabled/disabled] config syslog host all severity informational warning all facility local0 local1 local2 local3 local4 local5 local6 local7 udp_port ipadd...

  • Page 102

    Des-3326sr layer 3 fast ethernet switch cli reference manual 102 network monitoring commands show packet ports purpose used to display statistics about the packets sent and received by the switch. Syntax show packet ports description this command is used to display statistics about packets sent and ...

  • Page 103

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 103 example usage: to display the packets analysis for port 7 of module 2: des-3326sr:4#show packet port 2:7 port number : 2:7 frame size frame counts frames/sec frame type total total/sec ------------ ---------...

  • Page 104

    Des-3326sr layer 3 fast ethernet switch cli reference manual 104 network monitoring commands show error ports purpose used to display the error statistics for a range of ports. Syntax show error ports description this command will display all of the packet error statistics collected and logged by th...

  • Page 105

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 105 example usage: to display the errors of the port 3 of module 1: des-3326sr:4#show errors port 1:3 rx frames tx frames --------------- ---------------- crc error 0 excessive deferral 0 undersize 0 crc error 0...

  • Page 106

    Des-3326sr layer 3 fast ethernet switch cli reference manual 106 network monitoring commands example usage: to display the port utilization statistics: des-3326sr:4#show utilization port tx/sec rx/sec util port tx/sec rx/sec util ---- ---------- ---------- ---- ---- ---------- ---------- ---- 1:1 0 ...

  • Page 107

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 107 clear counters purpose used to clear the switch’s statistics counters. Syntax clear counters {ports } description this command will clear the counters used by the switch to compile statistics. Parameters − s...

  • Page 108

    Des-3326sr layer 3 fast ethernet switch cli reference manual 108 network monitoring commands clear log purpose used to clear the switch’s history log. Syntax clear log description this command will clear the switch’s history log. Parameters none. Restrictions only administrator-level users can issue...

  • Page 109

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 109 show log purpose used to display the switch history log. Syntax show log {index } description this command will display the contents of the switch’s history log. Parameters index − the show log command will ...

  • Page 110

    Des-3326sr layer 3 fast ethernet switch cli reference manual 110 network monitoring commands enable syslog purpose used to enable the system log to be sent to a remote host. Syntax enable syslog description the enable syslog command enables the system log to be sent to a remote host. Parameters none...

  • Page 111

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 111 disable syslog purpose used to enable the system log to be sent to a remote host. Syntax disable syslog description the disable syslog command enables the system log to be sent to a remote host. Parameters n...

  • Page 112

    Des-3326sr layer 3 fast ethernet switch cli reference manual 112 network monitoring commands show syslog purpose used to display the syslog protocol status as enabled or disabled. Syntax show syslog description the show syslog command displays the syslog status as enabled or disabled. Parameters non...

  • Page 113

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 113 create syslog host purpose used to create a new syslog host. Syntax config syslog host [all/] {severity [informational/warning/all]/ facility[local0/local1/local2/local3/ local4/local5/local6/local7]/udp_por...

  • Page 114

    Des-3326sr layer 3 fast ethernet switch cli reference manual 114 network monitoring commands create syslog host 6 informational: informational messages 7 debug: debug-level messages informational − specifies that informational messages will be sent to the remote host. This corresponds to number 6 fr...

  • Page 115

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 115 create syslog host 8 uucp subsystem 9 clock daemon 10 security/authorization messages 11 ftp daemon 12 ntp subsystem 13 log audit 14 log alert 15 clock daemon 16 local use 0 (local0) 17 local use 1 (local1) ...

  • Page 116

    Des-3326sr layer 3 fast ethernet switch cli reference manual 116 network monitoring commands create syslog host local4 − specifies that local use 4 messages will be sent to the remote host. This corresponds to number 20 from the list above. Local5 − specifies that local use 5 messages will be sent t...

  • Page 117

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 117 to create syslog host: des-3326sr:4#create syslog host 1 severity all facility local0 command: create syslog host 1 severity all facility local0 success. Des-3326sr:4# config syslog host purpose used to conf...

  • Page 118

    Des-3326sr layer 3 fast ethernet switch cli reference manual 118 network monitoring commands config syslog host corresponding severity level is currently supported on the switch. Numerical severity code 0 emergency: system is unusable 1 alert: action must be taken immediately 2 critical: critical co...

  • Page 119

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 119 config syslog host that have been designated are shown in the following: bold font means the facility values the switch supports now. Numerical facility code 0 kernel messages 1 user-level messages 2 mail sy...

  • Page 120

    Des-3326sr layer 3 fast ethernet switch cli reference manual 120 network monitoring commands config syslog host local1 − specifies that local use 1 messages will be sent to the remote host. This corresponds to number 17 from the list above. Local2 − specifies that local use 2 messages will be sent t...

  • Page 121

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 121 config syslog host number that the syslog protocol will use to send messages to the remote host. Ipaddress − specifies the ip address of the remote host where syslog messages will be sent. State [enabled/dis...

  • Page 122

    Des-3326sr layer 3 fast ethernet switch cli reference manual 122 network monitoring commands delete syslog host purpose used to remove a syslog host, that has been previously configured, from the switch. Syntax delete syslog host [/all] description the delete syslog host command is used to remove a ...

  • Page 123

    Des-3326sr layer 3 fast ethernet switch cli reference manual network monitoring commands 123 show syslog host purpose used to display the syslog hosts currently configured on the switch. Syntax show syslog host {} description the show syslog host command is used to display the syslog hosts that are ...

  • Page 124: Panning

    Des-3326sr layer 3 fast ethernet switch cli reference manual 124 spanning tree commands 9 s panning t ree c ommands the switch supports 802.1d stp and 802.1w rapid stp. The spanning tree commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following ...

  • Page 125

    Des-3326sr layer 3 fast ethernet switch cli reference manual spanning tree commands 125 config stp purpose used to setup stp and rstp on the switch. Syntax config stp {maxage /hellotime /forwarddelay /priority /fbpdu [enabled/disabled]/ txholdcount / version[rstp/stp]} description this command is us...

  • Page 126

    Des-3326sr layer 3 fast ethernet switch cli reference manual 126 spanning tree commands config stp network devices when stp is disabled on the switch. The default is enabled. Txholdcount - the maximum number of hello packets transmitted per interval. Default value = 3. Version [rstp/stp] - select th...

  • Page 127

    Des-3326sr layer 3 fast ethernet switch cli reference manual spanning tree commands 127 config stp ports purpose used to setup stp on the port level. Syntax config stp ports {cost /priority / migrate [yes/no]/ edge [true/false]/ p2p [true/false]/ state [enabled/disabled] description this command is ...

  • Page 128

    Des-3326sr layer 3 fast ethernet switch cli reference manual 128 spanning tree commands config stp ports 4 − in numerical order. Migrate [yes/no] – yes will enable the port to migrate from 802.1d stp status to 802.1w rstp status. Rstp can coexist with standard stp, however the benefits of rstp are n...

  • Page 129

    Des-3326sr layer 3 fast ethernet switch cli reference manual spanning tree commands 129 example usage: to configure stp with path cost 19, priority 15, and state enabled for ports 1-5 of module 1. Des-3326sr:4#config stp_ports 1:1-1:5 cost 19 priority 15 state enabled command: config stp_ports 1-5 c...

  • Page 130

    Des-3326sr layer 3 fast ethernet switch cli reference manual 130 spanning tree commands example usage: to enable stp, globally, on the switch: des-3326sr:4#enable stp command: enable stp success. Des-3326sr:4#.

  • Page 131

    Des-3326sr layer 3 fast ethernet switch cli reference manual spanning tree commands 131 disable stp purpose used to globally disable stp on the switch. Syntax disable stp description this command allows the spanning tree protocol to be globally disabled on the switch. Parameters none. Restrictions o...

  • Page 132

    Des-3326sr layer 3 fast ethernet switch cli reference manual 132 spanning tree commands show stp purpose used to display the switch’s current stp configuration. Syntax show stp description this command displays the switch’s current stp configuration. Parameters none restrictions none. Example usage:...

  • Page 133

    Des-3326sr layer 3 fast ethernet switch cli reference manual spanning tree commands 133 des-3326sr:4#show stp command: show stp stp status : enabled max age : 20 hello time : 2 forward delay : 15 priority : 32768 stp version : rstp tx hold count : 3 forwarding bpdu : enabled designated root bridge: ...

  • Page 134

    Des-3326sr layer 3 fast ethernet switch cli reference manual 134 spanning tree commands des-3326sr:4# show stp ports purpose used to display the switch’s current per-port group stp configuration. Syntax show stp ports description this command displays the switch’s current per-port group stp configur...

  • Page 135

    Des-3326sr layer 3 fast ethernet switch cli reference manual spanning tree commands 135 show stp ports port 4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical order. Restrictions none example usage: to display stp state of port 1-9 of module 1: des-332...

  • Page 136: Orwarding

    Des-3326sr layer 3 fast ethernet switch cli reference manual 136 forwarding database commands 10 f orwarding d atabase c ommands the layer 2 forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ...

  • Page 137

    Des-3326sr layer 3 fast ethernet switch cli reference manual forwarding database commands 137 create fdb purpose used to create a static entry to the unicast mac address forwarding table (database) syntax create fdb [port ] description this command will make an entry into the switch’s unicast mac ad...

  • Page 138

    Des-3326sr layer 3 fast ethernet switch cli reference manual 138 forwarding database commands create multicast_fdb purpose used to create a static entry to the multicast mac address forwarding table (database) syntax create multicast_fdb description this command will make an entry into the switch’s ...

  • Page 139

    Des-3326sr layer 3 fast ethernet switch cli reference manual forwarding database commands 139 config multicast_fdb purpose used to configure the switch’s multicast mac address forwarding database. Syntax config multicast_fdb [add/delete] description this command configures the multicast mac address ...

  • Page 140

    Des-3326sr layer 3 fast ethernet switch cli reference manual 140 forwarding database commands example usage: to add multicast mac forwarding: des-3326sr:4#config multicast_fdb default 01-00-5e-00-00-00 add 1:1-1:5 command: config multicast_fdb default 01-00-5e-00-00-00 add 1:1- 1:5 success. Des-3326...

  • Page 141

    Des-3326sr layer 3 fast ethernet switch cli reference manual forwarding database commands 141 config macentry unicast aging_time purpose used to configure the switch’s mac address aging time. Syntax config macentry unicast aging_time description this command is used to set the age-out timer for the ...

  • Page 142

    Des-3326sr layer 3 fast ethernet switch cli reference manual 142 forwarding database commands delete fdb purpose used to delete an entry to the switch’s forwarding database. Syntax delete fdb description this command is used to delete a previous entry to the switch’s mac address forwarding database....

  • Page 143

    Des-3326sr layer 3 fast ethernet switch cli reference manual forwarding database commands 143 clear fdb purpose used to clear the switch’s forwarding database of all dynamically learned mac addresses. Syntax clear fdb [vlan /port /all] description clears dynamically learned entries to the switch’s f...

  • Page 144

    Des-3326sr layer 3 fast ethernet switch cli reference manual 144 forwarding database commands show multicast_fdb purpose used to display the contents of the switch’s multicast forwarding database. Syntax show mulitcast_fdb [vlan /mac_address description this command is used to display the current co...

  • Page 145

    Des-3326sr layer 3 fast ethernet switch cli reference manual forwarding database commands 145 show fdb purpose used to display the current unicast mac address forwarding database. Syntax show fdb {port /vlan /mac_address /static/aging_time} description this command will display the current contents ...

  • Page 146

    Des-3326sr layer 3 fast ethernet switch cli reference manual 146 forwarding database commands example usage: to display unicast mac address table: des-3326sr:4#show fdb command: show fdb unicast mac address ageing time = 300 vid vlan name mac address port type ---- ---------------- -----------------...

  • Page 147: Roadcast

    Des-3326sr layer 3 fast ethernet switch cli reference manual broadcast storm control commands 147 11 b roadcast s torm c ontrol c ommands the broadcast storm control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parame...

  • Page 148

    Des-3326sr layer 3 fast ethernet switch cli reference manual 148 broadcast storm control commands config traffic control purpose used to configure broadcast/multicast traffic control. Syntax config traffic control [/all] broadcast [enabled/disabled]/multicast [enabled/disabled]/dlf [enabled/disabled...

  • Page 149

    Des-3326sr layer 3 fast ethernet switch cli reference manual broadcast storm control commands 149 example usage: to configure traffic control: des-3326sr:4#config traffic control 1-3,1-2 broadcast enabled command: config traffic control 1-1,2-2 broadcast enabled success. Des-3326sr:4# show traffic c...

  • Page 150

    Des-3326sr layer 3 fast ethernet switch cli reference manual 150 broadcast storm control commands example usage: to display traffic control setting: des-3326sr:4#show traffic control command: show traffic control traffic control broadcast multicast destination group [ports] threshold storm storm loo...

  • Page 151: Qos C

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 151 12 qos c ommands the mac address priority commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config bandwidth_control rx_rate no_limit...

  • Page 152

    Des-3326sr layer 3 fast ethernet switch cli reference manual 152 qos commands config bandwidth_control purpose used to configure bandwidth control on a by-port basis. Syntax config bandwidth_control {re_rate [no_limit/ 1000>]/tx_rate [no_limit/ 1000>]} description the config bandwidth_control comman...

  • Page 153

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 153 config bandwidth_control − specifies the limit, in mbps, that the above ports will be allowed to receive packets. Tx_rate − specifies that one of the parameters below (no_limit or 1000>) will be applied to the rate at whic...

  • Page 154

    Des-3326sr layer 3 fast ethernet switch cli reference manual 154 qos commands show bandwidth_control purpose used to display the bandwidth control configuration on the switch. Syntax show bandwidth_control {} description the show bandwidth_control command displays the current bandwidth control confi...

  • Page 155

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 155 example usage: to create des-3326sr:4#show bandwidth_control 1-10 command: show bandwidth_control 1-10 bandwidth control table port rx rate (mbit/sec) tx_rate (mbit/sec) ---- ------------------------ ----------------------...

  • Page 156

    Des-3326sr layer 3 fast ethernet switch cli reference manual 156 qos commands config scheduling purpose used to configure traffic scheduling for each of the switch’s cos queues. Syntax config scheduling {max_packet /max_latency } description the switch contains four hardware priority queues per port...

  • Page 157

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 157 config scheduling specify the maximum amount of time that packets will be delayed before being transmitted. For a given priority queue, a value between 0 and 255 can be specified. This number is then multiplied by 16 milli...

  • Page 158

    Des-3326sr layer 3 fast ethernet switch cli reference manual 158 qos commands config scheduling before being allowed to transmit any packets that have accumulated in its transmit buffer. A value between 0 and 255 can be specified − with this value being multiplied by 16 ms to arrive at the total tim...

  • Page 159

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 159 show scheduling switch. The switch’s default max_latency = 0. At this value it will empty the four hardware queues in order, from the highest priority (queue 0) to the lowest priority (queue 3). Parameters none. Restrictio...

  • Page 160

    Des-3326sr layer 3 fast ethernet switch cli reference manual 160 qos commands config 802.1p user_priority purpose used to map the 802.1p user priority of an incoming packet to one of the four hadware queues available on the switch. Syntax config 802.1p user_priority description the config 802.1p use...

  • Page 161

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 161 config 802.1p user_priority − specifies which of the switch’s hardware priority queues the 802.1p priority value (specified above) will be mapped to. Restrictions only administrator-level users can issue this command. Exam...

  • Page 162

    Des-3326sr layer 3 fast ethernet switch cli reference manual 162 qos commands show 802.1p user_priority purpose used to display the current mapping between an incoming packet’s 802.1p priority value and one of the switch’s four hardware priority queues. Syntax show 802.1p user_priority description t...

  • Page 163

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 163 config 802.1p default_priority purpose used to specify how to map an incoming packet that has no 802.1p priority tag to one of the switch’s four hardware priority queues. Syntax config 802.1p default_priority [/all] descri...

  • Page 164

    Des-3326sr layer 3 fast ethernet switch cli reference manual 164 qos commands config 802.1p default_priority packet will be given before being forwarded to its destination. Restrictions only administrator-level users can issue this command. Example usage: to configure 802.1p default priority on the ...

  • Page 165

    Des-3326sr layer 3 fast ethernet switch cli reference manual qos commands 165 show 802.1 default_priority purpose used to display the currently configured 802.1p priority value that will be assigned to an incoming, untagged packet before being forwarded to its destination. Syntax show 802.1p default...

  • Page 166

    Des-3326sr layer 3 fast ethernet switch cli reference manual 166 qos commands example usage: to display the current 802.1p default priority configuration on the switch: des-3326sr:4# show 802.1p default_priority command: show 802.1p default_priority port priority ------- ----------- 1 0 2 0 3 0 4 0 ...

  • Page 167: Ort

    Des-3326sr layer 3 fast ethernet switch cli reference manual port mirroring commands 167 15 p ort m irroring c ommands the port mirroring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config mirror port [add...

  • Page 168

    Des-3326sr layer 3 fast ethernet switch cli reference manual 168 port mirroring commands config mirror port purpose used to configure a mirror port − source port pair on the switch. Syntax config mirror port add source ports [rx/tx/both] description this command allows a range of ports to have all o...

  • Page 169

    Des-3326sr layer 3 fast ethernet switch cli reference manual port mirroring commands 169 config mirror port tx − allows the mirroring of only packets sent (flowing out of) the port or ports in the port list. Both − mirrors all the packets received or sent by the port or ports in the port list. Restr...

  • Page 170

    Des-3326sr layer 3 fast ethernet switch cli reference manual 170 port mirroring commands config mirror delete purpose used to delete a port mirroring configuration/ syntax config mirror delete source [rx/tx/both] description this command is used to delete a previously entered port mirroring configur...

  • Page 171

    Des-3326sr layer 3 fast ethernet switch cli reference manual port mirroring commands 171 example usage: to delete the mirroring ports: des-3326sr:4#config mirror 1:5 delete source 1-5 both command: config mirror 1:5 delete source 1-5 both success. Des-3326sr:4# enable mirror purpose used to enable a...

  • Page 172

    Des-3326sr layer 3 fast ethernet switch cli reference manual 172 port mirroring commands disable mirror purpose used to disable a previously entered port mirroring configuration. Syntax disable mirror description this command, combined with the enable mirror command above, allows you to enter a port...

  • Page 173

    Des-3326sr layer 3 fast ethernet switch cli reference manual port mirroring commands 173 show mirror purpose used to show the current port mirroring configuration on the switch. Syntax show mirror description this command displays the current port mirroring configuration on the switch. Parameters no...

  • Page 174: Vlan C

    Des-3326sr layer 3 fast ethernet switch cli reference manual 174 vlan commands 14 vlan c ommands the vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create vlan tag advertisement delete vlan config vlan a...

  • Page 175

    Des-3326sr layer 3 fast ethernet switch cli reference manual vlan commands 175 create vlan purpose used to create a vlan on the switch. Syntax create vlan {tag /advertisement} description this command allows you to create a vlan on the switch. Parameters − the name of the vlan to be created. − the v...

  • Page 176

    Des-3326sr layer 3 fast ethernet switch cli reference manual 176 vlan commands delete vlan purpose used to delete a previously configured vlan on the switch. Syntax delete vlan description this command will delete a previously configured vlan on the switch. Parameters − the vlan name of the vlan you...

  • Page 177

    Des-3326sr layer 3 fast ethernet switch cli reference manual vlan commands 177 config vlan purpose used to add additional ports to a previously configured vlan. Syntax config vlan add [tagged/untagged/forbidden]/delete /advertisement [enabled/disabled]} description this command allows you to add por...

  • Page 178

    Des-3326sr layer 3 fast ethernet switch cli reference manual 178 vlan commands config vlan highest port number of the range (also separated by a colon) are specified. The beginning and end of the port list range are separated by a dash. For example, 1:3 would specify switch number 1, port 3. 2:4 spe...

  • Page 179

    Des-3326sr layer 3 fast ethernet switch cli reference manual vlan commands 179 config gvrp purpose used to configure gvrp on the switch. Syntax config gvrp [/all] {state [enabled/disabled]/ingress_checking [enabled/disabled]} description this command is used to configure the group vlan registration ...

  • Page 180

    Des-3326sr layer 3 fast ethernet switch cli reference manual 180 vlan commands example usage: to set the ingress checking status, the sending and receiving gvrp information and port vlan id(pvid): des-3326sr:4#config gvrp 1:1-1:5 state enabled ingress_checking enabled pvid 21 command: config gvrp 1:...

  • Page 181

    Des-3326sr layer 3 fast ethernet switch cli reference manual vlan commands 181 enable gvrp purpose used to enable gvrp on the switch. Syntax enable gvrp description this command, along with disable gvrp below, is used to enable and disable gvrp on the switch − without changing the gvrp configuration...

  • Page 182

    Des-3326sr layer 3 fast ethernet switch cli reference manual 182 vlan commands disable gvrp purpose used to disable gvrp on the switch. Syntax disable gvrp description this command, along with disable gvrp below, is used to enable and disable gvrp on the switch − without changing the gvrp configurat...

  • Page 183

    Des-3326sr layer 3 fast ethernet switch cli reference manual vlan commands 183 show vlan purpose used to display the current vlan configuration on the switch syntax show vlan {} description this command displays summary information about each vlan including the vlan id, vlan name, the tagging/untagg...

  • Page 184

    Des-3326sr layer 3 fast ethernet switch cli reference manual 184 vlan commands static ports : 1:26,2:26 untagged ports : forbidden ports : total entries : 2 des-3326sr:4# show gvrp purpose used to display the gvrp status for a port list on the switch. Syntax show gvrp {} description this command dis...

  • Page 185

    Des-3326sr layer 3 fast ethernet switch cli reference manual vlan commands 185 show gvrp restrictions none. Example usage: to display gvrp port status: des-3326sr:4#show gvrp command: show gvrp global gvrp : disabled port pvid gvrp ingress checking ---- -------- -------- -------------------- 1:1 21 ...

  • Page 186

    Des-3326sr layer 3 fast ethernet switch cli reference manual 186 vlan commands 1:22 1 disabled disabled 1:23 1 disabled disabled 1:24 1 disabled disabled 1:25 1 disabled disabled 1:26 0 enabled disabled 2:1 1 disabled disabled 2:2 1 disabled disabled 2:3 1 disabled disabled 2:4 1 disabled disabled 2...

  • Page 187: Ink

    Des-3326sr layer 3 fast ethernet switch cli reference manual link aggregation commands 187 17 l ink a ggregation c ommands the link aggregation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create link_aggre...

  • Page 188

    Des-3326sr layer 3 fast ethernet switch cli reference manual 188 link aggregation commands create link_aggregation group_id purpose used to create a link aggregation group on the switch. Syntax create link_aggregation group_id description this command will create a link aggregation group. Parameters...

  • Page 189

    Des-3326sr layer 3 fast ethernet switch cli reference manual link aggregation commands 189 delete link_aggregation group_id purpose used to delete a previously configured link aggregation group. Syntax delete link_aggregation group_id description this command is used to delete a previously configure...

  • Page 190

    Des-3326sr layer 3 fast ethernet switch cli reference manual 190 link aggregation commands config link_aggregation purpose used to configure a previously created link aggregation group. Syntax config link_aggregation group_id {master_port /ports / {state [enabled/disabled]} description this command ...

  • Page 191

    Des-3326sr layer 3 fast ethernet switch cli reference manual link aggregation commands 191 config link_aggregation port number, separated by commas. State [enabled/disabled] − allows you to enable or disable the specified link aggregation group. Restrictions only administrator-level users can issue ...

  • Page 192

    Des-3326sr layer 3 fast ethernet switch cli reference manual 192 link aggregation commands config link_aggregation algorithm purpose used to configure the link aggregation algorithm. Syntax config link_aggregation algorithm [mac_source/mac_destination/mac_source_de st/ ip_source/ip_destination/ip_so...

  • Page 193

    Des-3326sr layer 3 fast ethernet switch cli reference manual link aggregation commands 193 example usage: to configure link aggregation algorithm for mac-source-dest: des-3326sr:4#config link_aggregation algorithm mac_source_dest command: config link_aggregation algorithm mac_source_dest success. De...

  • Page 194

    Des-3326sr layer 3 fast ethernet switch cli reference manual 194 link aggregation commands show link_aggregation purpose used to display the current link aggregation configuration on the switch. Syntax show link_aggregation {group_id /algorithm} description this command will display the current link...

  • Page 195: Ip I

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip interface commands 195 18 ip i nterface c ommands the ip interface commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create ipif vlan state [enable...

  • Page 196

    Des-3326sr layer 3 fast ethernet switch cli reference manual 196 ip interface commands create ipif purpose used to create an ip interface on the switch. Syntax create ipif {state [enabled/disabled]} description this command will create an ip interface. Parameters − the name for the ip interface to b...

  • Page 197

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip interface commands 197 example usage: to create ip address 20.1.1.1 of ip interface ip2: des-3326sr:4#create ipif ip2 20.1.1.1/8 vlan2 state enabled command: create ipif ip2 20.1.1.1/8 vlan2 state enabled success. Des-3326sr:4#.

  • Page 198

    Des-3326sr layer 3 fast ethernet switch cli reference manual 198 ip interface commands config ipif purpose used to configure an ip interface on the switch. Syntax config ipif {vlan /ipaddress /state [enabled/disabled]} description this command is used to modify an existing ip interface on the switch...

  • Page 199

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip interface commands 199 example usage: to configure the ip interface ip2: des3326s:4#config ipif ip2 vlan vlan1 command: config ipif ip2 vlan vlan1 success. Des-3326sr:4#.

  • Page 200

    Des-3326sr layer 3 fast ethernet switch cli reference manual 200 ip interface commands delete ipif purpose used to delete a previously configured ip interface on the switch. Syntax delete ipif {/all} description this command will delete an ip interface from the switch. Parameters − the name of the i...

  • Page 201

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip interface commands 201 config ipif system purpose used to configure the system ip interface. Syntax config ipif system [{vlan /ipaddress /state [enabled/disabled]/bootp/dhcp}] description this command is used to configure the system ip ...

  • Page 202

    Des-3326sr layer 3 fast ethernet switch cli reference manual 202 ip interface commands example usage: to configure the ip interface system: des-3326sr:4#config ipif system ipaddress 10.48.74.122/8 command: config ipif system ipaddress 10.48.74.122/8 success. Des-3326sr:4#.

  • Page 203

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip interface commands 203 config ipif purpose used to configure an ip interface on the switch. Syntax config ipif {vlan /ipaddress /state [enabled/disabled]} description this command is used to configure an ip interface on the switch. Para...

  • Page 204

    Des-3326sr layer 3 fast ethernet switch cli reference manual 204 ip interface commands example usage: to configure the ip interface ip2: des-3326sr:4#config ipif ip2 vlan vlan1 command: config ipif ip2 vlan vlan1 success. Des-3326sr:4#.

  • Page 205

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip interface commands 205 enable ipif purpose used to enable an ip interface on the switch. Syntax enable ipif {/all} description this command, along with the disable ipif command below, allows you to enable or disable an ip interface on t...

  • Page 206

    Des-3326sr layer 3 fast ethernet switch cli reference manual 206 ip interface commands disable ipif purpose used to disable an ip interface on the switch. Syntax disable ipif {/all} description this command, along with the enable ipif command above, allows you to enable or disable an ip interface on...

  • Page 207

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip interface commands 207 show ipif purpose used to display the configuration of an ip interface on the switch. Syntax show ipif {} description this command will display the configuration of an ip interface on the switch. Parameters − the ...

  • Page 208: Ommands

    Des-3326sr layer 3 fast ethernet switch cli reference manual 208 arp commands 19 a rp c ommands the arp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create arpentry delete arpentry config arp_aging time cle...

  • Page 209

    Des-3326sr layer 3 fast ethernet switch cli reference manual arp commands 209 create arpentry purpose used to make a static entry into the arp table. Syntax create arpentry description this command is used to enter an ip address and the corresponding mac address into the switch’s arp table. Paramete...

  • Page 210

    Des-3326sr layer 3 fast ethernet switch cli reference manual 210 arp commands delete arpentry purpose used to delete a static entry into the arp table. Syntax delete arpentry {/all} description this command is used to delete a static arp entry, made using the create arpentry command above, by specif...

  • Page 211

    Des-3326sr layer 3 fast ethernet switch cli reference manual arp commands 211 config arp_aging purpose used to configure the age-out timer for arp table entries on the switch. Syntax config arp_aging time description this command sets the maximum amount of time, in seconds, that an arp entry can rem...

  • Page 212

    Des-3326sr layer 3 fast ethernet switch cli reference manual 212 arp commands show arpentry purpose used to display the arp table. Syntax show arpentry {ipif /ipaddress /static} description this command is used to display the current contents of the switch’s arp table. Parameters − the name of the i...

  • Page 213

    Des-3326sr layer 3 fast ethernet switch cli reference manual arp commands 213 system 10.1.1.169 00-50-ba-70-e4-4e dynamic system 10.1.1.254 00-01-30-fa-5f-00 dynamic system 10.9.68.1 00-a0-c9-a4-22-5b dynamic system 10.9.68.4 00-80-c8-2e-c7-45 dynamic system 10.10.27.51 00-80-c8-48-df-ab dynamic sys...

  • Page 214

    Des-3326sr layer 3 fast ethernet switch cli reference manual 214 arp commands clear arptable purpose used to remove all dynamic arp table entries. Syntax clear arptable description this command is used to remove dynamic arp table entries from the switch’s arp table. Static arp table entries are not ...

  • Page 215: Outing

    Des-3326sr layer 3 fast ethernet switch cli reference manual routing table commands 215 20 r outing t able c ommands the routing table commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create iproute default del...

  • Page 216

    Des-3326sr layer 3 fast ethernet switch cli reference manual 216 routing table commands create iproute purpose used to create an ip route entry to the switch’s ip routing table. Syntax create iproute [default/] {} description this command is used to create an ip route entry to the switch’s ip routin...

  • Page 217

    Des-3326sr layer 3 fast ethernet switch cli reference manual routing table commands 217 example usage: to add a static address 10.48.74.121 , mask 255.0.0.0 and gateway 10.1.1.254 to the routing table: des-3326sr:4#create iproute 10.48.74.121/255.0.0.0 10.1.1.254 1 command: create iproute 10.48.74.1...

  • Page 218

    Des-3326sr layer 3 fast ethernet switch cli reference manual 218 routing table commands example usage: to delete a static address 10.48.75.121, mask 255.0.0.0 from the routing table: des-3326sr:4#delete iproute 10.48.74.121/255.0.0.0 command: delete iproute 10.48.74.121/8 success. Des-3326sr:4# show...

  • Page 219

    Des-3326sr layer 3 fast ethernet switch cli reference manual routing table commands 219 example usage: to display the contents of the ip routing table: des-3326sr:4#show iproute command: show iproute ip address netmask gateway interface name hops protocol --------------- --------------- ------------...

  • Page 220: Oute

    Des-3326sr layer 3 fast ethernet switch cli reference manual 220 route redistribution commands 21 r oute r edistribution c ommands the switch port commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create route r...

  • Page 221

    Des-3326sr layer 3 fast ethernet switch cli reference manual route redistribution commands 221 create route redistribute dst ospf purpose used to add route redistribution settings for the exchange of rip routes to ospf routes on the switch. Syntax create route redistribute dst ospf src [static/rip/l...

  • Page 222

    Des-3326sr layer 3 fast ethernet switch cli reference manual 222 route redistribution commands create route redistribute dst ospf restrictions only administrator-level users can issue this command. Routing information source − rip. The static route table, and the local interface routing information....

  • Page 223

    Des-3326sr layer 3 fast ethernet switch cli reference manual route redistribution commands 223 example usage: to add route redistribution settings: des-3326sr:4#create route redistribute dst ospf src rip command: create route redistribute dst ospf src rip success. Des-3326sr:4# create route redistri...

  • Page 224

    Des-3326sr layer 3 fast ethernet switch cli reference manual 224 route redistribution commands create route redistribute dst rip the destination device. Metric − allows the entry of an ospf interface cost. This is analogous to a hop count in the rip routing protocol. Restrictions only administrator-...

  • Page 225

    Des-3326sr layer 3 fast ethernet switch cli reference manual route redistribution commands 225 entering the metric 0 specifies transparency. Example usage: to add route redistribution settings: des-3326sr:4#create route redistribute dst rip src ospf all metric 2 command: create route redistribute ds...

  • Page 226

    Des-3326sr layer 3 fast ethernet switch cli reference manual 226 route redistribution commands example usage: to delete route redistribution settings: des-3326sr:4#delete route redistribute dst rip src ospf command: delete route redistribute dst rip src ospf success. Des-3326sr:4# config route redis...

  • Page 227

    Des-3326sr layer 3 fast ethernet switch cli reference manual route redistribution commands 227 config route redistribute dst ospf redistributed. Parameters src − allows the selection of the protocol of the source device. Dst − allows the selection of the protocol of the destination device. Mettype −...

  • Page 228

    Des-3326sr layer 3 fast ethernet switch cli reference manual 228 route redistribution commands route source metric metric type rip 0 to 16777214 mettype 1 mettype 2 static 0 to 16777214 mettype 1 mettype 2 local 0 to 16777214 mettype 1 mettype 2 allowed metric type combinations are mettype 1 or mett...

  • Page 229

    Des-3326sr layer 3 fast ethernet switch cli reference manual route redistribution commands 229 config route redistribute dst rip purpose used to configure route redistribution from ospf to rip. Syntax config route redistribute dist rip src [local/static/ospf {all/internal/external/type_1/type_2}] {m...

  • Page 230

    Des-3326sr layer 3 fast ethernet switch cli reference manual 230 route redistribution commands routing information source − ospf and the static route table. Routing information will be redistributed to rip. The following table lists the allowed values for the routing metrics and the types (or forms)...

  • Page 231

    Des-3326sr layer 3 fast ethernet switch cli reference manual route redistribution commands 231 des-3326sr:4# show route redistribute purpose used to display the route redistribution on the switch. Syntax show route redistribute {dst [rip/ospf]/src [rip/static/local/ospf]} description displays the cu...

  • Page 232

    Des-3326sr layer 3 fast ethernet switch cli reference manual 232 route redistribution commands -------- ------------ -------- -------- static rip all 1 local ospf type-2 20 total entries : 2 des-3326sr:4#.

  • Page 233: Igmp C

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp commands 233 22 igmp c ommands the switch port commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config igmp all version query_interval max_respo...

  • Page 234

    Des-3326sr layer 3 fast ethernet switch cli reference manual 234 igmp commands config igmp purpose used to configure igmp on the switch. Syntax config igmp [/all] {version /query_interval /max_response_time / robustness_variable /last_member_query_interval /state [enabled/disabled]} description this...

  • Page 235

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp commands 235 config igmp restrictions only administrator-level users can issue this command. Example usage: to configure the igmp for the ip interface system. Des-3326sr:4#config igmp all version 1 state enabled command: config igmp a...

  • Page 236

    Des-3326sr layer 3 fast ethernet switch cli reference manual 236 igmp commands example usage: to display igmp configurations: des-3326sr:4#show igmp command: show igmp interface ip address ver- query maximum robust- last member state sion response ness query time value interval ------------ --------...

  • Page 237

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp commands 237 show igmp group purpose used to display the switch’s igmp group table. Syntax show igmp group {group } {ipif } description this command will display the igmp group configuration. Parameters group − the multicast group id....

  • Page 238

    Des-3326sr layer 3 fast ethernet switch cli reference manual 238 igmp commands 259 total entries: 5 des-3326sr:4#.

  • Page 239: Igmp S

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 239 23 igmp s nooping c ommands the switch port commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config igmp_snooping all host...

  • Page 240

    Des-3326sr layer 3 fast ethernet switch cli reference manual 240 igmp snooping commands command parameters dynamic each command is listed, in detail, in the following sections..

  • Page 241

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 241 config igmp_snooping purpose used to configure igmp snooping on the switch. Syntax config igmp_snooping [/all] {host_timeout /router_timeout /leave_timer /state [enabled/disabled]} description this command allows...

  • Page 242

    Des-3326sr layer 3 fast ethernet switch cli reference manual 242 igmp snooping commands config igmp_snooping restrictions only administrator-level users can issue this command. Example usage: to configure the igmp snooping: des-3326sr:4#config igmp_snooping default host_timeout 250 state enabled com...

  • Page 243

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 243 config igmp_snooping querier parameters − the name of the vlan for which igmp snooping querier is to be configured. Query_interval − specifies the amount of time in seconds between general query transmissions. Th...

  • Page 244

    Des-3326sr layer 3 fast ethernet switch cli reference manual 244 igmp snooping commands config igmp_snooping querier • last member query count— number of group-specific queries sent before the router assumes there are no local members of a group. The default number is the value of the robustness var...

  • Page 245

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 245 example usage: to configure the igmp snooping: des-3326sr:4#config igmp_snooping querier default query_interval 125 state enabled command: config igmp_snooping querier default query_interval 125 state enabled suc...

  • Page 246

    Des-3326sr layer 3 fast ethernet switch cli reference manual 246 igmp snooping commands config router_ports the highest port number in a group, separated by a dash. So, a port group including the switch ports 1, 2, and 3 would be entered as 1-3. Ports that are not contained within a group are specif...

  • Page 247

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 247 enable igmp_snooping purpose used to enable igmp snooping on the switch. Syntax enable igmp_snooping {forward_mcrouter_only} description this command allows you to enable igmp snooping on the switch. If forward_m...

  • Page 248

    Des-3326sr layer 3 fast ethernet switch cli reference manual 248 igmp snooping commands disable igmp_snooping purpose used to enable igmp snooping on the switch. Syntax disable igmp_snooping description this command disables igmp snooping on the switch. Igmp snooping can be disabled only if ip multi...

  • Page 249

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 249 show igmp_snooping purpose used to show the current status of igmp snooping on the switch. Syntax show igmp_snooping {vlan } description this command will display the current igmp snooping configuration on the sw...

  • Page 250

    Des-3326sr layer 3 fast ethernet switch cli reference manual 250 igmp snooping commands state : disabled vlan name : vlan2 query interval : 125 max response time : 10 robustness value : 2 last member query interval : 1 host timeout : 260 route timeout : 260 leave timer : 2 querier state : disabled q...

  • Page 251

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 251 show igmp_snooping group purpose used to display the current igmp snooping group configuration on the switch. Syntax show igmp_snooping group {vlan } description this command will display the current igmp snoopin...

  • Page 252

    Des-3326sr layer 3 fast ethernet switch cli reference manual 252 igmp snooping commands vlan name : default multicast group : 234.5.6.7 mac address : 01-00-5e-05-06-07 reports : 1 port member : 26 vlan name : default multicast group : 236.54.63.75 mac address : 01-00-5e-36-3f-4b reports : 1 port mem...

  • Page 253

    Des-3326sr layer 3 fast ethernet switch cli reference manual igmp snooping commands 253 show router_ports purpose used to display the currently configured router ports on the switch. Syntax show router_ports {vlan } {static/dynamic} description this command will display the router ports currently co...

  • Page 254

    Des-3326sr layer 3 fast ethernet switch cli reference manual 254 igmp snooping commands total entries: 2 des-3326sr:4#.

  • Page 255: Ootp

    Des-3326sr layer 3 fast ethernet switch cli reference manual bootp relay commands 255 24 b ootp r elay c ommands the bootp relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config bootp_relay hops time con...

  • Page 256

    Des-3326sr layer 3 fast ethernet switch cli reference manual 256 bootp relay commands config bootp_relay purpose used to configure the bootp relay feature of the switch. Syntax config bootp_relay {hops } {time } description this command is used to configure the bootp relay feature. Parameters hops −...

  • Page 257

    Des-3326sr layer 3 fast ethernet switch cli reference manual bootp relay commands 257 config bootp_relay add purpose used to add an ip destination address to the switch’s bootp relay table. Syntax config bootp_relay add ipif description this command adds an ip address as a destination to forward (re...

  • Page 258

    Des-3326sr layer 3 fast ethernet switch cli reference manual 258 bootp relay commands config bootp_relay delete purpose used to delete one or all ip destination addresses from the switch’s bootp relay table. Syntax config bootp_relay delete ipif description this command is used to delete one or all ...

  • Page 259

    Des-3326sr layer 3 fast ethernet switch cli reference manual bootp relay commands 259 enable bootp_relay purpose used to enable the bootp relay function on the switch. Syntax enable bootp_relay description this command, in combination with the disable bootp_relay command below, is used to enable and...

  • Page 260

    Des-3326sr layer 3 fast ethernet switch cli reference manual 260 bootp relay commands disable bootp_relay purpose used to disable the bootp relay function on the switch. Syntax disable bootp_relay description this command, in combination with the enable bootp_relay command above, is used to enable a...

  • Page 261

    Des-3326sr layer 3 fast ethernet switch cli reference manual bootp relay commands 261 show bootp_relay purpose used to display the current bootp relay configuration. Syntax show bootp_relay {ipif } description this command will display the current bootp relay configuration for the switch, or if an i...

  • Page 262: Dns R

    Des-3326sr layer 3 fast ethernet switch cli reference manual 262 dns relay commands 25 dns r elay c ommands the dns relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config dnsr primary secondary nameserve...

  • Page 263

    Des-3326sr layer 3 fast ethernet switch cli reference manual dns relay commands 263 config dnsr purpose used to configure the dns relay function. Syntax config dnsr [primary/secondary] nameserver description this command is used to configure the dns relay function on the switch. Parameters primary −...

  • Page 264

    Des-3326sr layer 3 fast ethernet switch cli reference manual 264 dns relay commands config dnsr [add/delete] static purpose used to add or delete a static entry into the switch’s dns resolution table. Syntax config dnsr [add/delete] static description this command allows you to add or delete entries...

  • Page 265

    Des-3326sr layer 3 fast ethernet switch cli reference manual dns relay commands 265 to delete an entry domain name dns1, ipaddress 10.43.21.12 from dns static table. Des-3326sr:4#config dnsr delete static dns1 10.43.21.12 command: config dnsr delete static dns1 10.43.21.12 success. Des-3326sr:4# ena...

  • Page 266

    Des-3326sr layer 3 fast ethernet switch cli reference manual 266 dns relay commands disable dnsr purpose used to disable dns relay on the switch. Syntax disable dnsr description this command is used, in combination with the enable dnsr command above, to enable and disable dns relay on the switch. Pa...

  • Page 267

    Des-3326sr layer 3 fast ethernet switch cli reference manual dns relay commands 267 enable dnsr cache purpose used to enable the dns relay cache. Syntax enable dnsr cache description this command is used, in combination with the disable dnsr cache command below, to enable and disable the dns relay c...

  • Page 268

    Des-3326sr layer 3 fast ethernet switch cli reference manual 268 dns relay commands disable dnsr cache purpose used to disable the dns relay cache. Syntax disable dnsr cache description this command is used, in combination with the enable dnsr cache command above, to enable and disable the dns relay...

  • Page 269

    Des-3326sr layer 3 fast ethernet switch cli reference manual dns relay commands 269 enable dnsr static purpose used to enable the dns relay static table. Syntax enable dnsr static description this command, in combination with the disable dnsr static command below, is used to enable or disable the dn...

  • Page 270

    Des-3326sr layer 3 fast ethernet switch cli reference manual 270 dns relay commands disable dnsr static purpose used to disable the dns relay static table. Syntax disable dnsr static description this command, in combination with the disable dnsr static command below, is used to enable or disable the...

  • Page 271

    Des-3326sr layer 3 fast ethernet switch cli reference manual dns relay commands 271 show dnsr purpose used to display the current dns relay static table. Syntax show dnsr {static} description this command is used to display the current dns relay static table. Parameters static − allows the display o...

  • Page 272

    Des-3326sr layer 3 fast ethernet switch cli reference manual 272 dns relay commands des-3326sr:4#show dnsr command: show dnsr dnsr status : disabled primary name server : 10.48.74.122 secondary name server : 20.48.74.123 dnsr cache status : enabled dnsr static table status : enabled dns relay static...

  • Page 273: Rip C

    Des-3326sr layer 3 fast ethernet switch cli reference manual rip commands 273 26 rip c ommands the rip commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config rip ipif all authentication [enabled /disabled] tx_...

  • Page 274

    Des-3326sr layer 3 fast ethernet switch cli reference manual 274 rip commands config rip rx_mode purpose used to configure rip on the switch. Syntax config rip [ipif /all] rx_mode [[disable/v1_only]/[v2_only/v1_and_v2] authentication [enabled/disabled] ] description this command is used to configure...

  • Page 275

    Des-3326sr layer 3 fast ethernet switch cli reference manual rip commands 275 config rip rx_mode restrictions only administrator-level users can issue this command. Example usage: to change the rip receive mode for the ip interface system. Des-3326sr:4#config rip ipif system rx_mode v1_only command:...

  • Page 276

    Des-3326sr layer 3 fast ethernet switch cli reference manual 276 rip commands config rip tx_mode purpose used to configure rip’s transmission mode. Syntax config rip [ipif /all]} tx_mode [disable/v1_only/v1_compatiable/v2_only] authentication [enabled/disabled] ] description this command is used to ...

  • Page 277

    Des-3326sr layer 3 fast ethernet switch cli reference manual rip commands 277 example usage: to change the rip transmission mode for the ip interface system. Des-3326sr:4#config rip ipif system tx_mode v1_only command: config rip ipif system tx_mode v1_only success. Des-3326sr:4#.

  • Page 278

    Des-3326sr layer 3 fast ethernet switch cli reference manual 278 rip commands enable rip purpose used to enable rip. Syntax enable rip description this command is used, along with the disable rip command below, to enable or disable rip on the switch. Parameters none. Restrictions only administrator-...

  • Page 279

    Des-3326sr layer 3 fast ethernet switch cli reference manual rip commands 279 disable rip purpose used to disable rip. Syntax disable rip description this command is used, along with the enable rip command below, to enable or disable rip on the switch. Parameters none. Restrictions only administrato...

  • Page 280

    Des-3326sr layer 3 fast ethernet switch cli reference manual 280 rip commands show rip purpose used to display the rip configuration and statistics for the switch. Syntax show rip {ipif } description this command will display the rip configuration and statistics for a given ip interface or for all i...

  • Page 281: Dvmrp C

    Des-3326sr layer 3 fast ethernet switch cli reference manual dvmrp commands 281 27 dvmrp c ommands the switch port commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config dvmrp ipif all metric probe neighbor_ti...

  • Page 282

    Des-3326sr layer 3 fast ethernet switch cli reference manual 282 dvmrp commands config dvmrp purpose used to configure dvmrp on the switch. Syntax config dvmrp [ipif /all] {metric /probe /neighbor_timeout /state [enabled/disabled] description this command is used to configure dvmrp on the switch. Pa...

  • Page 283

    Des-3326sr layer 3 fast ethernet switch cli reference manual dvmrp commands 283 config dvmrp this command. Example usage: to configure dvmrp configurations of ip interface system: des-3326sr:4#config dvmrp ipif system neighbor_timeout 30 metric 1 probe 5 command: config dvmrp ipif system neighbor_ti...

  • Page 284

    Des-3326sr layer 3 fast ethernet switch cli reference manual 284 dvmrp commands enable dvmrp purpose used to enable dvmrp. Syntax enable dvmrp description this command, in combination with the disable dvmrp below, to enable and disable dvmrp on the switch. Parameters none. Restrictions only administ...

  • Page 285

    Des-3326sr layer 3 fast ethernet switch cli reference manual dvmrp commands 285 disable dvmrp purpose used to disable dvmrp. Syntax disable dvmrp description this command, in combination with the enable dvmrp above, to enable and disable dvmrp on the switch. Parameters none. Restrictions only admini...

  • Page 286

    Des-3326sr layer 3 fast ethernet switch cli reference manual 286 dvmrp commands show dvmrp routing_table purpose used to display the current dvmrp routing table. Syntax show dvmrp routing table {ipaddress } description the command is used to display the current dvmrp routing table. Parameters − the ...

  • Page 287

    Des-3326sr layer 3 fast ethernet switch cli reference manual dvmrp commands 287 example usage: to display dvmrp routing table: des-3326sr:4#show dvmrp routing_table command: show dvmrp routing_table dvmrp routing table source address source mask next hop router hop learned interface expire ---------...

  • Page 288

    Des-3326sr layer 3 fast ethernet switch cli reference manual 288 dvmrp commands show dvmrp neighbor purpose used to display the dvmrp neighbor table. Syntax show dvmrp neighbor {ipif /ipaddress } description this command will display the current dvmrp neighbor table. Parameters − the name of the ip ...

  • Page 289

    Des-3326sr layer 3 fast ethernet switch cli reference manual dvmrp commands 289 show dvmrp nexthop purpose used to display the current dvmrp routing next hop table. Syntax show dvmrp nexthop {ipaddress /ipif } description this command will display the dvmrp routing next hop table. Parameters − the n...

  • Page 290

    Des-3326sr layer 3 fast ethernet switch cli reference manual 290 dvmrp commands example usage: to display dvmrp routing next hop table: des-3326sr:4#show dvmrp nexthop command: show dvmrp nexthop source ip address source mask interface name type ----------------- ---------------- --------------- ---...

  • Page 291

    Des-3326sr layer 3 fast ethernet switch cli reference manual dvmrp commands 291 show dvmrp purpose used to display the current dvmrp routing table. Syntax show dvmrp {} description the command will display the current dvmrp routing table. Parameters − the name of the ip interface for which you want ...

  • Page 292: Ip M

    Des-3326sr layer 3 fast ethernet switch cli reference manual 292 ip multicasting commands 28 ip m ulticasting c ommands the ip multicasting commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show ipmc cache group...

  • Page 293

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip multicasting commands 293 show ipmc cache purpose used to display the current ip multicast forwarding cache. Syntax show ipmc cache {group } {ipaddres } description this command will display the current ip multicast forwarding cache. Pa...

  • Page 294

    Des-3326sr layer 3 fast ethernet switch cli reference manual 294 ip multicasting commands usage example: to display the current ip multicast forwarding cache: des-3326sr:4#show ipmc cache command: show ipmc cache multicast group source ip addr. Source mask upstream expire prot. Neighbor time -------...

  • Page 295

    Des-3326sr layer 3 fast ethernet switch cli reference manual ip multicasting commands 295 show ipmc purpose used to display the ip multicast interface table. Syntax show ipmc {ipif /protocol [dvmrp/pim]} description this command will display the current ip multicast interface table. Parameters − the...

  • Page 296: Md5 C

    Des-3326sr layer 3 fast ethernet switch cli reference manual 296 md5 configuration commands 29 md5 c onfiguration c ommands the md5 configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config md5 key ...

  • Page 297

    Des-3326sr layer 3 fast ethernet switch cli reference manual md5 configuration commands 297 config md5 purpose used to enter configure an md5 key and password. Syntax config md5 description this command is used to configure an md5 key and password. Parameters − the md5 key id. − an md5 password of u...

  • Page 298

    Des-3326sr layer 3 fast ethernet switch cli reference manual 298 md5 configuration commands create md5 purpose used to create an md5 key table. Syntax create md5 key description this command is used to create an md5 key table. Parameters − the md5 key id. − an md5 password of up to 16 bytes. Restric...

  • Page 299

    Des-3326sr layer 3 fast ethernet switch cli reference manual md5 configuration commands 299 delete md5 purpose used to delete an md5 key table. Syntax delete md5 key description this command is used to delete an md5 key table. Parameters − the md5 key id. Restrictions only administrator-level users ...

  • Page 300

    Des-3326sr layer 3 fast ethernet switch cli reference manual 300 md5 configuration commands show md5 purpose used to display an md5 key table. Syntax show md5 {key } description this command will display the current md5 key table. Parameters − the md5 key id. Restrictions none. Usage example to disp...

  • Page 301: Ospf C

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 301 30 ospf c onfiguration c ommands the ospf configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config ospf ...

  • Page 302

    Des-3326sr layer 3 fast ethernet switch cli reference manual 302 ospf configuration commands command parameters config ospf host_route area metric show ospf host_route create ospf aggregation lsdb_type [summary] advertise [enabled/disabled] delete ospf aggregation lsdb_type [summary] config ospf agg...

  • Page 303

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 303 command parameters metric state [enabled/disabled] config ospf all area priority hello_interval dead_interval authentication [none/simple /md5 ] metric state [enabled/disabled] show ospf ipif show ospf all c...

  • Page 304

    Des-3326sr layer 3 fast ethernet switch cli reference manual 304 ospf configuration commands config ospf purpose used to configure the ospf router id. Syntax config ospf {router_id } description this command is used to configure the ospf router id. Parameters − the ospf router id. Restrictions only ...

  • Page 305

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 305 enable ospf purpose used to enable ospf on the switch. Syntax enable ospf description this command, in combination with the disable ospf command below, is used to enable and disable ospf on the switch. Param...

  • Page 306

    Des-3326sr layer 3 fast ethernet switch cli reference manual 306 ospf configuration commands disable ospf purpose used to disable ospf on the switch. Syntax disable ospf description this command, in combination with the enable ospf command above, is used to enable and disable ospf on the switch. Par...

  • Page 307

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 307 show ospf purpose used to display the current ospf state on the switch. Syntax show ospf description this command will display the current state of ospf on the switch, divided into the following categories: ...

  • Page 308

    Des-3326sr layer 3 fast ethernet switch cli reference manual 308 ospf configuration commands ospf interface settings interface ip address area id state link metric status ------------ ------------------ --------- -------- --------- --------- system 10.90.90.90/8 0.0.0.0 disabled link down 1 ip2 20.1...

  • Page 309

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 309 ospf area aggregation settings area id aggregated lsdb advertise network address type --------------- ------------------ -------- --------- total entries : 0 ospf host route settings host address metric area...

  • Page 310

    Des-3326sr layer 3 fast ethernet switch cli reference manual 310 ospf configuration commands create ospf area [enabled/disabled]/metric }] description this command is used to create an ospf area and configure its settings. Parameters − the ospf area id. Type − the ospf area mode of operation − stub ...

  • Page 311

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 311 delete ospf area purpose used to delete an ospf area. Syntax delete ospf area description this command is used to delete an ospf area. Parameters − − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx...

  • Page 312

    Des-3326sr layer 3 fast ethernet switch cli reference manual 312 ospf configuration commands config ospf area purpose used to configure an ospf area’s settings. Syntax config ospf area type [normal/stub {stub_summary [enabled/disabled]/metric }] description this command is used to configure an ospf ...

  • Page 313

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 313 show ospf area purpose used to display an ospf area’s configuration. Syntax show ospf area {} description this command will display the current ospf area configuration. Parameters − − a 32-bit number in the ...

  • Page 314

    Des-3326sr layer 3 fast ethernet switch cli reference manual 314 ospf configuration commands create ospf host_route purpose used to configure ospf host route settings. Syntax create ospf host_route {area /metric } description this command is used to configure the ospf host route settings. Parameters...

  • Page 315

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 315 delete ospf host_route purpose used to delete an ospf host route. Syntax delete ospf host_route description this command is used to delete an ospf host route. Parameters − the ip address of the ospf host. Re...

  • Page 316

    Des-3326sr layer 3 fast ethernet switch cli reference manual 316 ospf configuration commands config ospf host_route purpose used to configure ospf host route settings. Syntax config ospf host_route {area /metric } description this command is used to configure an ospf host route settings. Parameters ...

  • Page 317

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 317 show ospf host_route purpose used to display the current ospf host route table. Syntax show ospf host_route {} description this command will display the current ospf host route table. Parameters − the ip add...

  • Page 318

    Des-3326sr layer 3 fast ethernet switch cli reference manual 318 ospf configuration commands create ospf aggregation purpose used to configure ospf area aggregation settings. Syntax create ospf aggregation lsdb_type [summary] {advertise [enabled/disabled]} description this command is used to create ...

  • Page 319

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 319 usage example to create an ospf area aggregation: des-3326sr:4#create ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled command: create ospf aggregation 10.1.1.1 10.48.76.122/16 l...

  • Page 320

    Des-3326sr layer 3 fast ethernet switch cli reference manual 320 ospf configuration commands delete ospf aggregation purpose used to delete an ospf area aggregation configuration. Syntax delete ospf aggregation lsdb_type [summary] description this command is used to delete an ospf area aggregation c...

  • Page 321

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 321 command: delete ospf aggregation 10.1.1.1 10.48.76..122/16 lsdb_type summary success. Des-3326sr:4# config ospf aggregation purpose used to configure the ospf area aggregation settings. Syntax config ospf ag...

  • Page 322

    Des-3326sr layer 3 fast ethernet switch cli reference manual 322 ospf configuration commands config ospf aggregation this command. Usage example to configure the ospf area aggregation settings: des-3326sr:4#config ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled command:...

  • Page 323

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 323 show ospf aggregation purpose used to display the current ospf area aggregation settings. Syntax show ospf aggregation {} description this command will display the current ospf area aggregation settings. Par...

  • Page 324

    Des-3326sr layer 3 fast ethernet switch cli reference manual 324 ospf configuration commands show ospf lsdb purpose used to display the ospf link state database (lsdb). Syntax show ospf lsdb {area_id /advertise_router /type [rtrlink/netlink/summary/assummary/asextli nk]} description this command wil...

  • Page 325

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 325 usage example to display the link state database of ospf: des-3326sr:4#show ospf lsdb command: show ospf lsdb area lsdb advertising link state cost sequence id type router id id number ----------------------...

  • Page 326

    Des-3326sr layer 3 fast ethernet switch cli reference manual 326 ospf configuration commands show ospf neighbor purpose used to display the current ospf neighbor router table. Syntax show ospf neighbor {} description this command will display the current ospf neighbor router table. Parameters − the ...

  • Page 327

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 327 show ospf virtual neighbor purpose used to display the current ospf virtual neighbor router table. Syntax show ospf virtual_neighbor {} description this command will display the current ospf virtual neighbor...

  • Page 328

    Des-3326sr layer 3 fast ethernet switch cli reference manual 328 ospf configuration commands config ospf ipif purpose used to configure the ospf interface settings. Syntax config ospf ipif {area /priority /hello_interval /dead_interval /authentication [none/simple /md5 ]/metric /state [enabled/disab...

  • Page 329

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 329 config ospf ipif router before the selected area declares that router down. An interval between 5 and 65535 seconds can be specified. The dead interval must be evenly divisible by the hello interval. − a cas...

  • Page 330

    Des-3326sr layer 3 fast ethernet switch cli reference manual 330 ospf configuration commands config ospf all purpose used to configure all of the ospf interfaces on the switch at one time. Syntax config ospf all {area /priority /hello_interval /dead_interval /authentication [none/simple /md5 ]/metri...

  • Page 331

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 331 config ospf all 65535 seconds can be specified. The dead interval must be evenly divisible by the hello interval. − a case-sensitive password. − a previously configured md5 key id (1 to 255). Metric − this f...

  • Page 332

    Des-3326sr layer 3 fast ethernet switch cli reference manual 332 ospf configuration commands show ospf ipif purpose used to display the current ospf interface settings for the specified interface name. Syntax show ospf ipif {} description this command will display the current ospf interface settings...

  • Page 333

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 333 show ospf all purpose used to display the current ospf settings of all the ospf interfaces on the switch. Syntax show ospf all description this command will display the current ospf settings for all ospf int...

  • Page 334

    Des-3326sr layer 3 fast ethernet switch cli reference manual 334 ospf configuration commands network medium type: broadcast metric: 1 area id: 1.0.0.0 administrative state: enabled priority: 1 dr state: dr dr address: 123.234.12.34 backup dr address: none hello interval: 10 dead interval: 40 transmi...

  • Page 335

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 335 config ospf virtual_link purpose used to configure the ospf virtual interface settings. Syntax config ospf virtual_link {hello_interval /dead_interval /authentication [simple /md5 /none]} description this co...

  • Page 336

    Des-3326sr layer 3 fast ethernet switch cli reference manual 336 ospf configuration commands config ospf virtual_link the receipt of hello packets from a neighbor router before the selected area declares that router down. An interval between 5 and 65535 seconds can be specified. The dead interval mu...

  • Page 337

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 337 create ospf virtual_link purpose used to create an ospf virtual interface. Syntax create ospf virtual_link {hello_interval /authentication [none/simple /md5 ]} description this command is used to create an o...

  • Page 338

    Des-3326sr layer 3 fast ethernet switch cli reference manual 338 ospf configuration commands create ospf virtual_link parameters − a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the ospf area in the ospf domain. − the ospf router id for the remote area. This ...

  • Page 339

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 339 create ospf virtual_link this command. Usage example to create an ospf virtual interface: des-3326sr:4#create ospf virtual_link 10.1.12 20.1.1.1 hello_interval 10 command: create ospf virtual_link 10.1.12 20...

  • Page 340

    Des-3326sr layer 3 fast ethernet switch cli reference manual 340 ospf configuration commands delete ospf virtual_link − the ospf router id for the remote area. This is a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the remote area’s area border router. The ro...

  • Page 341

    Des-3326sr layer 3 fast ethernet switch cli reference manual ospf configuration commands 341 show ospf virtual_link ospf domain. − the ospf router id for the remote area. This is a 32-bit number in the form of an ip address (xxx.Xxx.Xxx.Xxx) that uniquely identifies the remote area’s area border rou...

  • Page 342: Ommand

    Des-3326sr layer 3 fast ethernet switch cli reference manual 342 command history list 31 c ommand h istory l ist the switch port commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ? Show command_history dir confi...

  • Page 343

    Des-3326sr layer 3 fast ethernet switch cli reference manual command history list 343 ? Purpose used to display all commands in the command line interface (cli). Syntax ? Description this command will display all of the commands available through the command line interface (cli). Parameters none. Re...

  • Page 344

    Des-3326sr layer 3 fast ethernet switch cli reference manual 344 command history list show command_history purpose used to display the command history. Syntax show command_history description this command will display the command history. Parameters none. Restrictions none. Usage example to display ...

  • Page 345

    Des-3326sr layer 3 fast ethernet switch cli reference manual command history list 345 dir purpose used to display all commands. Syntax dir description this command will display all commands. Parameters none. Restrictions none. Usage example to display all of the commands: des-3326sr:4#dir command: d...

  • Page 346

    Des-3326sr layer 3 fast ethernet switch cli reference manual 346 command history list config dvmrp config gvrp config igmp config igmp snooping config ingress_checking config ipif config ipif system - more -.

  • Page 347

    Des-3326sr layer 3 fast ethernet switch cli reference manual command history list 347 config command_history purpose used to configure the command history. Syntax config command_history description this command is used to configure the command history. Parameters − restrictions none. Usage example t...

  • Page 348: Echnical

    Des-3326sr layer 3 fast ethernet switch cli reference manual 348 technical specifications a t echnical s pecifications general standards: ieee 802.3 10base-t ethernet ieee 802.3u 100base-tx fast ethernet ieee 802.3z 1000base-sx gigabit ethernet ieee 802.3ab 1000base-t gigabit ethernet ieee 802.1 p/q...

  • Page 349

    Des-3326sr layer 3 fast ethernet switch cli reference manual technical specifications 349 general network cables: 10base-t: 100base-tx: fiber optic: 2-pair utp cat. 3,4,5 (100 m) eia/tia- 568 100-ohm stp (100 m) 2-pair utp cat. 5 (100 m) eia/tia-568 100-ohm stp (100 m) iec 793-2:1992 type a1a - 50/1...

  • Page 350

    Des-3326sr layer 3 fast ethernet switch cli reference manual 350 technical specifications physical and environmental emi: fcc class a, ce class a, vcci class a, bsmi class a, c-tick class a fcc part 15/ieces-003 (canada), vcci class a ite, en55022/en50082-1 or en%%o24, c-tick (as/nzs3548, bsmi (cns ...

  • Page 351

    Des-3326sr layer 3 fast ethernet switch cli reference manual.

  • Page 352: Ndex

    Passport 1424t layer 3 fast ethernet switch cli reference manual i ndex.

  • Page 353

    Des-3326sr layer 3 fast ethernet switch cli reference manual a ac inputs ............................... 375 c connecting to the switch vt100-compatible terminal19 d dimensions ............................. 375 h humidity ................................ 375 i ip address ...............................

  • Page 354

    Passport 1424t layer 3 fast ethernet switch cli reference manual.