1. DL manuals
  2. D-Link
  3. Switch
  4. DES-3528 - xStack Switch - Stackable
  5. Cli Reference Manual

D-Link DES-3528 - xStack Switch - Stackable Cli Reference Manual

Manual is about: Layer 2 Managed Stackable Fast Ethernet Switch CLI

Summary of DES-3528 - xStack Switch - Stackable

  • Page 1

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 503 config cfm ais md purpose this command is used to configure the parameters of the ais function on a mep. Syntax config cfm ais md ma mepid {period [1sec

  • Page 2: Table Of Contents

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide ii table of contents introduction .................................................................................................................................... 5 using the console cli ............

  • Page 3

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide iii time and sntp commands ...................................................................................................... 309 arp and gratuitous arp commands .....................................

  • Page 4

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide iv local route commands ............................................................................................................ 554 mstp debug enhancement commands ..................................

  • Page 5: Introduction

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 5 introduction the switch can be managed through the switch’s serial port, telnet, or the web-based management agent. The command line interface (cli) can be used to configure and manage the switch vi...

  • Page 6

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 6 boot procedure v1.00.B008 ------------------------------------------------------------------------------- power on self test ........................................ 100 % mac address : 00-22-b0-10-...

  • Page 7: Using The Console Cli

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 7 using the console cli the des-3528/52 series supports a console management interface that allows the user to connect to the switch’s management agent via a serial port and a terminal or a computer r...

  • Page 8

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 8 clear igmp_snooping data_driven_group clear igmp_snooping statistics counter clear jwac auth_state clear log clear mac_based_access_control auth_state clear mld_snooping data_driven_group ctrl+c esc...

  • Page 9

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 9 des-3528:admin# the top-level commands consist of commands such as show or config . Most of these commands require one or more parameters to narrow the top-level command. This is equivalent to show ...

  • Page 10: Command Syntax

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 10 command syntax the following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the cli and available thro...

  • Page 12

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 12 multiple page display control keys space displays the next page. Ctrl+c stops the display of remaining pages when multiple pages are to be displayed. Esc stops the display of remaining pages when m...

  • Page 13: Basic Switch Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 13 basic switch commands the basic switch commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create account [adm...

  • Page 16

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 16 delete account purpose used to delete an existing user account. Syntax delete account description this command is used to delete an existing entry. Parameters − name of the user who will be deleted...

  • Page 17

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 17 disable password encryption purpose used to disable password encryption. Syntax disable password encryption description the user account configuration information will be stored in the configuratio...

  • Page 18

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 18 show switch purpose used to display general information about the switch. Syntax show switch description this command displays information about the switch. Parameters none. Restrictions none. Exam...

  • Page 19

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 19 show serial_port purpose used to display the current serial port settings. Syntax show serial_port description this command displays the current serial port settings. Parameters none. Restrictions ...

  • Page 20

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 20 enable clipaging purpose used to pause the scrolling of the console screen when a command displays more than one page. Syntax enable clipaging description this command is used when issuing a comman...

  • Page 21

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 21 telnet to the remote switch: des-3528:admin# telnet 172.18.168.12 tcp_port 50 command: telnet 172.18.168.12 tcp_port 50 connecting to server,please wait.... Des-3528 gigabit ethernet switch command...

  • Page 22

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 22 enable web purpose used to enable the http-based management software on the switch. Syntax enable web description this command is used to enable the web-based management software on the switch. The...

  • Page 23

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 23 des-3528:admin# save command: save saving all configurations to nv-ram... Done. Des-3528:admin# reboot purpose used to restart the switch. Syntax reboot {force_agree} description this command is us...

  • Page 24

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 24 login purpose used to log in a user to the switch’s console. Syntax login description this command is used to initiate the login procedure. The user will be prompted for a username and password. Pa...

  • Page 27

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 27 des-3528:admin#config temperature threshold high 80 command: config temperature threshold high 80 success. Des-3528:admin# show environment purpose this command is used to display the device’s inte...

  • Page 28

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 28 modify banner and prompt commands administrator level users can modify the login banner (greeting message) and command prompt by using the commands described below. Command parameters config comman...

  • Page 29

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 29 config greeting _message purpose used to configure the login banner (greeting message). Syntax config greeting _message {default} description this command is used to modify the login banner (greeti...

  • Page 30

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 30 show greeting_message purpose used to view the currently configured greeting message configured on the switch. Syntax show greeting_message description this command is used to view the currently co...

  • Page 32

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 32 example usage: to configure the speed of ports 1-3 of unit 1 to be 10 mbps, full duplex, learning enabled, state enabled and flow control enabled: des-3528:admin# config ports 1-3 speed 10_full lea...

  • Page 33

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 33 port state/ settings connection address mdix speed/duplex/flowctrl speed/duplex/flowctrl learning ------- -------- --------------------- ---------------------- --------- 1 enabled auto/disabled lin...

  • Page 34

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 34 enable jumbo_frame purpose used to enable the jumbo frame function on the switch. Syntax enable jumbo_frame description this command will allow ethernet frames larger than 1536 bytes to be processe...

  • Page 35: Port Security Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 35 port security commands the switch’s port security commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config p...

  • Page 36

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 36 command: config port_security ports 1-5 admin_state enable max_learning_addr 5 lock_address_mode deleteonreset success. Des-3528:admin# delete port_security_entry purpose used to delete a port secu...

  • Page 38

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 38 disable port_security trap_log purpose used to disable the trap log for port security. Syntax disable port_security trap_log description this command, along with the enable port_security trap_log, ...

  • Page 40: Stacking Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 40 stacking commands the stacking configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config box_pr...

  • Page 41

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 41 des-3528:admin# show stack_information purpose used to display the stack information table. Syntax show stack_information description this command display stack information. Parameters none. Restri...

  • Page 42

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 42 show stacking_mode purpose used to view the current stacking mode. Syntax show stacking_mode description this command will display whether the current stacking mode is enabled or disabled. Paramete...

  • Page 43

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 43 des-3528:admin# config stacking force_master_role state enable command: config stacking force_master_role state enable success. Des-3528:admin#.

  • Page 44

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 44 network management (snmp) commands the switch supports the simple network management protocol (snmp) versions 1, 2c, and 3. Users can specify which version of the snmp users want to use to monitor ...

  • Page 47

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 47 des-3528:admin# create snmp user dlink default encrypted by_password auth md5 canadian priv none command: create snmp user dlink default encrypted by_password auth md5 canadian priv none success. D...

  • Page 49

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 49 show snmp view purpose used to display an snmp view previously created on the switch. Syntax show snmp view {} description this command displays an snmp view previously created on the switch. Param...

  • Page 50

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 50 create snmp community purpose used to create an snmp community string to define the relationship between the snmp manager and an agent. The community string acts like a password to permit access to...

  • Page 51

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 51 show snmp community purpose used to display snmp community strings configured on the switch. Syntax show snmp community {} description this command is used to display snmp community strings that ar...

  • Page 52

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 52 show snmp engineid purpose used to display the identification of the snmp engine on the switch. Syntax show snmp engineid description this command displays the identification of the snmp engine on ...

  • Page 54

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 54 delete snmp group purpose used to remove an snmp group from the switch. Syntax delete snmp group description this command is used to remove an snmp group from the switch. Parameters − an alphanumer...

  • Page 57

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 57 show snmp v6host purpose this command is used to display the recipient for which the traps are targeted. Syntax show snmp v6host {} description this command is used to display the recipient for whi...

  • Page 58

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 58 to create the trusted host: des-3528:admin# create trusted_host 10.62.32.1 command: create trusted_host 10.62.32.1 success. Config trusted_host purpose used to configure the access interfaces for t...

  • Page 59

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 59 management stations ip address access interface ---------------------------------------------------------------- 10.62.32.1/32 10.62.32.1/16 total entries: 2 des-3528:admin# delete trusted_host pur...

  • Page 60

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 60 enable snmp authenticate_traps purpose used to enable snmp authentication trap support. Syntax enable snmp authenticate_traps description this command is used to enable snmp authentication trap sup...

  • Page 61

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 61 des-3528:admin# disable snmp authenticate_traps purpose used to disable snmp authentication trap support. Syntax disable snmp authenticate_traps description this command is used to disable snmp aut...

  • Page 62

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 62 success. Des-3528:admin# config snmp system_name purpose used to configure the name for the switch. Syntax config snmp system_name description this command configures the name of the switch. Parame...

  • Page 63

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 63 des-3528:admin# disable snmp command: disable snmp success. Des-3528:admin#.

  • Page 64: Switch Utility Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 64 switch utility commands the switch utility commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters download [firmw...

  • Page 65

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 65 to download a configuration file: des-3528:admin# download cfg_fromtftp 10.48.74.121 c:\cfg\setting.Txt command: download cfg_fromtftp 10.48.74.121 c:\cfg\setting.Txt connecting to server.............

  • Page 66

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 66 show firmware information purpose used to display the firmware section information. Syntax show firmware information description this command is used to display the firmware section information. Pa...

  • Page 68

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 68 show config parameters effective - show only commands which affects the behavior of the device. For example, if stp is disabled, then for stp configuration, only “stp is disabled” is displayed. All...

  • Page 71

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 71 network monitoring commands the network monitoring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters show pa...

  • Page 72

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 72 show packet ports purpose used to display statistics about the packets sent and received by the switch. Syntax show packet ports description this command is used to display statistics about packets...

  • Page 73

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 73 oversize 0 late collision 0 fragment 0 excessive collision 0 jabber 0 single collision 0 drop pkts 0 collision 0 symbol error 0 ctrl+c esc q quit space n next page p previous page r refresh show ut...

  • Page 74

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 74 show utilization dram purpose this command is used to display the dram utilization. Syntax show utilization dram description this command is used to display the dram utilization. Parameters none. R...

  • Page 75

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 75 to display the flash utilization: des-3528:admin# show utilization flash command: show utilization flash unit 1 flash memory utilization : total flash : 16384 kb used flash : 7662 kb utilization : ...

  • Page 77

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 77 to the syslog function on the switch: des-3528:admin# enable syslog command: enable syslog success. Des-3528:admin# disable syslog purpose used to disable the syslog sending messages. Syntax disabl...

  • Page 79

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 79 create syslog host local0 − specifies that local use 0 messages will be sent to the remote host. This corresponds to number 16 from the list above. Local1 − specifies that local use 1 messages will...

  • Page 81

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 81 config syslog host local0 − specifies that local use 0 messages will be sent to the remote host. This corresponds to number 16 from the list above. Local1 − specifies that local use 1 messages will...

  • Page 84

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 84 des-3528:admin# show attack_log command: show attack_log index time log text ---- --------------- ----------------------- 2 00000 days 01:25:43 possible spoofing attack from 000d01002301 port 6:3 1...

  • Page 86

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 86 system severity trap : information system severity log : information des-3528:admin#.

  • Page 87

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 87 multiple spanning tree protocol (mstp) commands this switch supports three versions of the spanning tree protocol: 802.1d stp, 802.1w rapid stp and 802.1s mstp. Multiple spanning tree protocol, or ...

  • Page 88

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 88 command parameters show stp mst_config_id each command is listed, in detail, in the following sections. Enable stp purpose used to globally enable stp on the switch. Syntax enable stp description t...

  • Page 89

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 89 to set the switch globally for the multiple spanning tree protocol (mstp): des-3528:admin# config stp version mstp command: config stp version mstp success des-3528:admin# config stp purpose used t...

  • Page 91

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 91 config stp ports the port cannot maintain this status (for example if the port is forced to half-duplex operation) the p2p status changes to operate as if the p2p value were false . The default set...

  • Page 93

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 93 success. Des-3528:admin# config stp priority purpose used to configure the bridge priority. Syntax config stp priority instance_id description this command is used to update the stp instance config...

  • Page 95

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 95 hello time : 2 forward delay : 15 max hops : 20 tx hold count : 6 forwarding bpdu : disabled nni bpdu address : dot1ad des-3528:admin# status 2 : stp enabled for rstp des-3528:admin# show stp comma...

  • Page 96

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 96 des-3528:admin# show stp ports command: show stp ports mstp port information ---------------------- port index : 1 , hello time: 2 /2 , port stp : enabled , external pathcost : auto/200000 , edge p...

  • Page 97

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 97 show stp mst_config_id purpose used to display the mstp configuration identification. Syntax show stp mst_config_id description this command displays the switch’s current mstp configuration identif...

  • Page 98

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 98 forwarding database commands the layer 2 forwarding database commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command paramete...

  • Page 101

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 101 delete fdb purpose used to delete an entry to the switch’s forwarding database. Syntax delete fdb description this command is used to delete a previous entry to the switch’s mac address forwarding...

  • Page 103

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 103 1 default 00-02-a5-fd-66-97 15 dynamic 1 default 00-03-09-18-10-01 15 dynamic 1 default 00-03-9d-73-32-f0 15 dynamic 1 default 00-03-b3-00-09-e9 15 dynamic 1 default 00-04-00-00-00-00 15 dynamic 1...

  • Page 104

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 104 100 /sales forward_all_groups 200 /pm forward_all_groups 600 /customer filter unregistered groups total entries : 3 des-3528:admin#.

  • Page 105: Traffic Control Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 105 traffic control commands on a computer network, packets such as multicast packets and broadcast packets continually flood the network as normal procedure. At times, this traffic may increase do to...

  • Page 106

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 106 config traffic control purpose used to configure broadcast/multicast/unicast packet storm control. The software mechanism is provided to monitor the traffic rate in addition to the hardware storm ...

  • Page 107

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 107 example usage: to configure traffic control and enable broadcast storm control for ports 1-12: des-3528:admin# config traffic control 1-12 broadcast enable action shutdown threshold 1 countdown 10...

  • Page 108

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 108 des-3528:admin# show traffic control purpose used to display current traffic control settings. Syntax show traffic control { } description this command displays the current storm traffic control c...

  • Page 110: Qos Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 110 qos commands the switch supports 802.1p priority queuing. The switch has 8 priority queues, but it has 7 priority queues available . Q7 is reserved for stacking function. These priority queues are...

  • Page 112

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 112 7 no limit no limit no limit no limit 8 no limit no limit no limit no limit 9 no limit no limit no limit no limit 10 no limit no limit no limit no limit des-3528:admin# config per_queue bandwidth_...

  • Page 113

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 113 show per_queue bandwidth_control purpose used to display the per port per cos queue bandwidth control setting. Syntax show per_queue bandwidth_control {} description this command is used to displa...

  • Page 115

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 115 to configure the traffic scheduling mechanism for each cos queue: des-3528:admin# config scheduling_mechanism ports 1 strict command: config scheduling_mechanism ports 1 strict success. Des-3528:a...

  • Page 116

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 116 to display the scheduling mechanism: des-3528:admin#show scheduling_mechanism 1-4 command: show scheduling_mechanism 1-4 port mode ----- ------ 1 strict 2 strict 3 strict 4 strict des-3528:admin# ...

  • Page 117

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 117 show 802.1p user_priority purpose used to display the current mapping between an incoming packet’s 802.1p priority value and one of the switch’s seven hardware priority queues. Syntax show 802.1p ...

  • Page 118

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 118 des-3528:admin# config 802.1p default_priority all 5 command: config 802.1p default_priority all 5 success. Des-3528:admin# show 802.1 default_priority purpose used to display the current configur...

  • Page 119

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 119 des-3528:admin# enable hol_prevention command: enable hol_prevention success. Des-3528:admin# disable hol_prevention purpose used to disable hol prevention. Syntax disable hol_prevention descripti...

  • Page 120: Port Mirroring Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 120 port mirroring commands the port mirroring commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config mirror ...

  • Page 121

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 121 success. Des-3528:admin# enable mirror purpose used to enable a previously entered port mirroring configuration. Syntax enable mirror description this command, combined with the disable mirror com...

  • Page 122

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 122 mirror status: enabled target port : 1 mirrored port rx: 2-5 tx: 2-5 des-3528:admin#.

  • Page 125

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 125 delete vlan purpose used to delete a previously configured vlan on the switch. Syntax delete vlan description this command will delete a previously configured vlan on the switch. Parameters − the ...

  • Page 129

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 129 disable gvrp purpose used to disable the garp vlan registration protocol (gvrp). Syntax disable gvrp description this command, along with enable gvrp , is used to enable and disable gvrp on the sw...

  • Page 130

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 130 static untagged ports : forbidden ports : total static vlan entries : 1 total gvrp vlan entries: 1 des-3528:admin# des-3528:admin# show vlan ports 1-4 command: show vlan ports 1-4 port vid untagge...

  • Page 131

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 131 create dot1v_protocol_group group_id purpose used to create a protocol group for protocol vlan function. Syntax create dot1v_protocol_group group_id {group_name } description this command creates ...

  • Page 134

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 134 des-3528:admin# show port dot1v ports 1-2 command: show port dot1v ports 1-2 port : 1 protocol group id vlan name protocol priority ----------------- ---------------- ----------------- 1 default -...

  • Page 135

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 135 des-3528:admin# disable pvid auto_assign command: disable pvid auto_assign success. Des-3528:admin# show pvid auto_assign purpose used to show pvid auto-assigment state. Syntax show pvid auto_assi...

  • Page 136

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 136 show gvrp purpose used to display the gvrp global setting and it’s timer’s value. Syntax show gvrp description this command displays gvrp global setting and it’s timer’s value. Parameters none. Re...

  • Page 140: Voice Vlan Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 140 voice vlan commands the voice vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable voice_vlan [vla...

  • Page 141

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 141 disable voice_vlan purpose used to disable the global voice vlan function. Syntax disable voice_vlan description this command disables the global voice vlan function on the switch. When the voice ...

  • Page 143

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 143 config voice_vlan aging_time purpose used to config voice vlan aging time. Syntax config voice_vlan aging_time description this command is used to set the aging time of the voice vlan. The aging t...

  • Page 144

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 144 command: show voice_vlan voice vlan state : enabled vlan id : 1 vlan name : default priority : 6 aging time : 60 minutes log state : enabled member ports : 1-28 dynamic member ports : des-3528:adm...

  • Page 145

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 145 ----- --------- -------- 1 disabled auto 2 disabled auto 3 disabled auto 4 disabled auto 5 disabled auto des-3528:admin# show voice_vlan voice_device ports purpose used to show voice devices conne...

  • Page 146: Subnet-Based Vlan Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 146 subnet-based vlan commands the subnet-based vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create s...

  • Page 149: Asymmetric Vlan Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 149 asymmetric vlan commands the asymmetric vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable asymm...

  • Page 150

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 150 show asymmetric_vlan purpose used to view the asymmetric vlan state on the switch. Syntax show asymmetric_vlan description this command displays the asymmetric vlan state on the switch. Parameters...

  • Page 151: Link Aggregation Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 151 link aggregation commands the link aggregation commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create lin...

  • Page 152

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 152 delete link_aggregation purpose used to delete a previously configured link aggregation group. Syntax delete link_aggregation group_id description this command is used to delete a previously confi...

  • Page 155

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 155 des-3528:admin#.

  • Page 156

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 156 ip–mac-port binding (impb) commands impb is a security application found on edge switches which are usually directly connected to hosts. Impb enables administrators to configure (or snoop) pairs o...

  • Page 161

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 161 config address_binding ip_mac ports when enabled on a port, all arp packets with a source ip address of 0.0.0.0 is forwarded; when set to disable, they are blocked. Forward_dhcppkt – by default, t...

  • Page 162

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 162 to show ip–mac–port binding global configuration: des-3528:admin#show address_binding command: show address_binding trap/log : disabled dhcp snoop(ipv4) : disabled dhcp snoop(ipv6) : disabled nd s...

  • Page 163

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 163 show address_binding dhcp_snoop purpose this command is used to display the ip–mac–port binding dhcp snooping. Syntax show address_binding dhcp_snoop {max_entry {ports }} description this command ...

  • Page 165

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 165 show address_binding nd_snoop binding_entry purpose this command is used to display the ip–mac–port binding nd snoop binding entry. Syntax show address_binding nd_snoop binding_entry {port } descr...

  • Page 167

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 167 to disable address binding trap log on the switch: des-3528:admin# disable address_binding trap_log command: disable address_binding trap_log success. Des-3528:admin# debug address_binding purpose...

  • Page 169

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 169 enable address_binding nd_snoop purpose this command is used to enable nd snooping on the switch. Syntax enable address_binding nd_snoop description this command is used to enable nd snooping on t...

  • Page 170

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 170 success. Des-3528:admin# clear address_binding nd_snoop binding_entry ports purpose this command is used to clear the nd snooping entries on specified ports. Syntax clear address_binding nd_snoop ...

  • Page 172

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 172 limited ip multicast address commands the limited ip multicast command allows the administrator to permit or deny access to a port or range of ports by specifying a range of multicast addresses. T...

  • Page 177: Basic Ip Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 177 basic ip commands the ip interface commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config ipif [{ipaddres...

  • Page 181

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 181 to display ip interface settings. Des-3528:admin# show ipif system command: show ipif system ip interface : system vlan name : default interface admin state : enabled ipv4 address : 10.24.73.21/8 ...

  • Page 182

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 182 show ipif_ipv6_link_local_auto purpose display the link local address automatic configuration state. Syntax show ipif_ipv6_link_local_auto {} description display the link local address automatic c...

  • Page 183: Multicast Vlan Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 183 multicast vlan commands the multicast vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create igmp_sn...

  • Page 184

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 184 command parameters show mld_snooping multicast_vlan_group { } delete mld_snooping multicat_vlan enable mld_snooping multicast_vlan disable mld_snooping multicast_vlan show mld_snooping multicast_v...

  • Page 186

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 186 to display the multicast groups configured for a multicast vlan. Des-3528:admin# show igmp_snooping multicast_vlan_group v1 command: show igmp_snooping multicast_vlan_group v1 vlan name vlan id mu...

  • Page 187

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 187 disable igmp_snooping multicast_vlan purpose used to disable the multicast vlan function. Syntax disable igmp_snooping multicast_vlan description this command is used to disable the igmp snooping ...

  • Page 188

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 188 config igmp_snooping multicast_vlan forward_unmatched purpose used to configure forwarding or dropping of the multicast vlan unmatched packet. Syntax config igmp_snooping multicast_vlan forward_un...

  • Page 189

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 189 config igmp_snooping multicast_vlan_group_profile purpose used to configure an igmp snooping multicast group profile on the switch, and to add or delete multicast address for the profile. Syntax c...

  • Page 190

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 190 show igmp_snooping multicast_vlan_group_profile purpose used to show the information about an igmp multicast vlan group profile on the switch. Syntax show igmp_snooping multicast_vlan_group_profil...

  • Page 191

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 191 show igmp_snooping multicast_vlan_group purpose used to display the multicast group profiles configured for the specified igmp multicast vlan. Syntax show igmp_snooping multicast_vlan_group { } de...

  • Page 193

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 193 to create an mld multicast vlan group profile "g1": des-3528:admin# create mld_snooping multicast_vlan_group_profile g1 command: create mld_snooping multicast_vlan_group_profile g1 success. Des-35...

  • Page 194

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 194 show mld_snooping multicast_vlan_group_profile purpose used to show the information about an mld multicast vlan group profile on the switch. Syntax show mld_snooping multicast_vlan_group_profile {...

  • Page 195

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 195 show mld_snooping multicast_vlan_group purpose used to display the multicast group profiles configured for the specified mld multicast vlan. Syntax show mld_snooping multicast_vlan_group { } descr...

  • Page 196

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 196 success. Des-3528:admin# disable mld_snooping multicast_vlan purpose used to disable the mld multicast vlan function. Syntax disable mld_snooping multicast_vlan description this command is used to...

  • Page 197

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 197 des-3528:admin#show mld_snooping multicast_vlan new command: show mld_snooping multicast_vlan new mld multicast vlan global state : disabled mld multicast vlan forward unmatched : enabled vlan nam...

  • Page 198

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 198 igmp / mld snooping commands the igmp / mld snooping commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters conf...

  • Page 203

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 203 config igmp_snooping querier enable - enter enable to enable this state. Disable - enter disable to disable this state. Version - (optional) specify the version of igmp packet that will be sent by...

  • Page 205

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 205 des-3528:admin# create igmp_snooping static_group vlan default 239.1.1.1 command: create igmp_snooping static_group vlan default 239.1.1.1 success. Des-3528:admin# delete igmp_snooping static_grou...

  • Page 206

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 206 des-3528:admin# config igmp_snooping static_group vlan default 239.1.1.1 delete 2:9- 2:10 command: create igmp_snooping static_group vlan default 239.1.1.1 delete 2:9-2:10 success. Des-3528:admin#...

  • Page 207

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 207 config igmp_snooping data_driven_learning purpose this command is used to enable or disable the data driven learning of an igmp snooping group. Syntax config igmp_snooping data_driven_learning max...

  • Page 209

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 209 to display the igmp snooping rate limit for ports 1 to 5: des-3528:admin# show igmp_snooping rate_limit ports 1:1-1:5 command: show igmp_snooping rate_limit ports 1:1-1:5 port rate limit -------- ...

  • Page 210

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 210 des-3528:admin# show igmp_snooping group command: show igmp_snooping group source/group : 10.0.0.2/225.0.0.2 vlan name/vid : default/1 member ports : 1-2 up time : 280 expiry time : 120 filter mod...

  • Page 213

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 213 show igmp_snooping statistics counter purpose this command displays the statistics counter for igmp protocol packets that are received by the switch since igmp snooping was enabled. Syntax show ig...

  • Page 214

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 214 to display the igmp snooping statistics counter for a port: des-3528:admin# show igmp_snooping statistics counter ports 1 command: show igmp_snooping statistics counter ports 1 port # ： 1 --------...

  • Page 215

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 215 des-3528:admin# clear igmp_snooping statistic counter command: clear igmp_snooping statistic counter success. Des-3528:admin# config mld_snooping purpose this command is used to configure mld snoo...

  • Page 217

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 217 config mld_snooping querier value 1-2 > - enter the version number value here. This value must be between 1 and 2. Restrictions only administrator and operator and power-user-level users can issue...

  • Page 218

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 218 config mld_snooping router_ports_forbidden purpose this command allows you to designate a range of ports as being not connected to multicast- enabled routers. Syntax config mld_snooping mrouter_po...

  • Page 219

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 219 des-3528:admin# show mld_snooping command: show mld_snooping mld snooping global state : disabled data driven learning max entries : 128 vlan name : default query interval : 125 max response time ...

  • Page 220

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 220 the fourth item is a data-driven learned entry. The member port list is empty. The multicast packets will be forwarded to the router ports. If the router port list is empty, the packet will be dro...

  • Page 225

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 225 config mld_snooping data_driven_learning purpose this command is used to enable or disable the data-driven learning of an mld snooping group. Syntax config mld_snooping data_driven_learning max_le...

  • Page 227

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 227 des-3528:admin# show mld_snooping statistics counter vlanid 1 command: show mld_snooping statistics counter vlanid 1 vlan name : default ----------------------------------------------- group numbe...

  • Page 229

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 229 config igmp access_authentication ports purpose this command is used to enable or disable the igmp access control function for the specified ports. Syntax config igmp access_authentication ports [...

  • Page 230

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 230 des-3528:admin#show igmp access_authentication ports all command: show igmp access_authentication ports all port state ----- --------- 1:1 enabled 1:2 enabled 1:3 enabled 1:4 enabled 1:5 enabled 1...

  • Page 231: Dhcp Relay Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 231 dhcp relay commands the dhcp relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config dhcp_relay {hop...

  • Page 233

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 233 des-3528:admin# config dhcp_relay delete ipif system 10.58.44.6 command: config dhcp_relay delete ipif system 10.58.44.6 success. Des-3528:admin# config dhcp_relay option_82 state purpose used to ...

  • Page 234

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 234 des-3528:admin# config dhcp_relay option_82 check enable command: config dhcp_relay option_82 check enable success. Des-3528:admin# config dhcp_relay option_82 policy purpose used to configure the...

  • Page 235

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 235 show dhcp_relay purpose used to display the current dhcp/bootp relay configuration. Syntax show dhcp_relay {ipif } description this command will display the current dhcp relay configuration for th...

  • Page 236

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 236 enable dhcp_relay purpose used to enable the dhcp/bootp relay function on the switch. Syntax enable dhcp_relay description this command is used to enable the dhcp/bootp relay function on the switc...

  • Page 237

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 237 des-3528:admin# config dhcp_relay option_60 state enable command: config dhcp_relay option_60 state enable success. Des-3528:admin# config dhcp_relay option_60 add purpose this command is used to ...

  • Page 241

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 241 matching rules: client-id type relay rule ----------- ---- --------- 00-01-22-33-44-55 mac address drop total entries : 1 des-3528:admin# config dhcp_local_relay vlan purpose used to enable or dis...

  • Page 242

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 242 disable dhcp_local_relay purpose used to disable the dhcp local relay function on the switch. Syntax disable dhcp_local_relay description this command is used to disable the dhcp local relay funct...

  • Page 243

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 243 des-3528:admin# config dhcp_relay add vlanid 1-10 10.43.21.12 command: config dhcp_relay add vlanid 1-10 10.43.21.12 success. Des-3528:admin# # to display the dhcp relay status: des-3528:admin# sh...

  • Page 244

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 244 802.1x commands (including guest vlans) the switch implements the server-side of the ieee 802.1x port-based and host-based network access control. This mechanism is intended to allow only authoriz...

  • Page 246

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 246 create 802.1x user purpose used to create 802.1x user. Syntax create 802.1x user description this command creates an 802.1x user. Parameters − specifies adding user name restrictions only administ...

  • Page 253

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 253 create 802.1x guest_vlan purpose used to configure a pre-existing vlan as an 802.1x guest vlan. Syntax create 802.1x guest_vlan description this command is used to configure a pre-defined vlan as ...

  • Page 254

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 254 show 802.1x guest_vlan purpose used to view the configurations for an 802.1x guest vlan. Syntax show 802.1x guest_vlan description this command is used to display the settings for the vlan that ha...

  • Page 257

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 257 total entries : 1 des-3528:admin# show auth_statistics purpose used to display authenticator statistics information. Syntax show auth_statistics {ports } description this command displays authenti...

  • Page 258

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 258 des-3528:admin# show auth_diagnostics ports 1 command: show auth_diagnostics ports 1 port number : 1 original rx vid 3 mac address 00-05-5d-f9-16-76 entersconnecting 1 eaplogoffswhileconnecting 0 ...

  • Page 259

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 259 show auth_client purpose used to display authentication client information syntax show auth_client description this command displays authentication client information parameters none. Restrictions...

  • Page 260

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 260 radiusaccclientserverportnumber 0 radiusaccclientroundtriptime 0 radiusaccclientrequests 0 radiusaccclientretransmissions 0 radiusaccclientresponses 0 radiusaccclientmalformedresponses 0 radiusacc...

  • Page 261

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 261 accounting service ------------------- network : enabled shell : enabled system : enabled des-3528:admin#.

  • Page 262

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 262 access control list (acl) commands the switch implements access control lists that enable the switch to deny network access to specific devices or device groups based on ip settings and mac addres...

  • Page 265

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 265 create access_profile purpose used to create an access profile on the switch and to define which parts of each incoming frame’s header the switch will examine. Masks can be entered that will be co...

  • Page 266

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 266 create access_profile the user may deny packets by denying certain flag bits within the packets. The user may choose between all, urg (urgent), ack (acknowledgement), psh (push), rst (reset), syn ...

  • Page 267

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 267 00-00-00-00-00-01 destination_mac 00-00-00-00-00-02 802.1p ethernet_type success. Des-3528:admin# delete access_profile purpose used to delete a previously created access profile. Syntax delete ac...

  • Page 268

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 268 config access_profile purpose used to configure an access profile on the switch and to define specific values that will be used to by the switch to determine if a given packet should be forwarded ...

  • Page 269

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 269 config access_profile ip − specifies that the switch will look into the ip fields in each packet. Vlan − specifies that the access profile will only apply to this vlan. Vlan_id - specifies that th...

  • Page 270

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 270 config access_profile tcp – specifies that the switch will examine each frame’s transmission control protocol (tcp) field. • src_port_mask − specifies a tcp port mask for the source port. • dst_po...

  • Page 271

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 271 note: address resolution protocol (arp) is the standard for finding a host's hardware address (mac address). However, arp is vulnerable as it can be easily spoofed and utilized to attack a lan (kn...

  • Page 272

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 272 create cpu access_profile purpose used to create an access profile specifically for cpu interface filtering on the switch and to define which parts of each incoming frame’s header the switch will ...

  • Page 273

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 273 create cpu access_profile and fin (finish). • udp − specifies that the switch will examine each frame’s user datagram protocol (udp) field. • src_port_mask − specifies a udp port mask for the sour...

  • Page 274

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 274 delete cpu access_profile purpose used to delete a previously created cpu access profile. Syntax delete cpu access_profile [profile_id description this command is used to delete a previously creat...

  • Page 275

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 275 config cpu access_profile purpose used to configure a cpu access profile used for cpu interface filtering and to define specific values that will be used to by the switch to determine if a given p...

  • Page 276

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 276 config cpu access_profile value. • code − specifies that the access profile will apply to this icmp code value. Igmp − specifies that the switch will examine the internet group management protocol...

  • Page 277

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 277 config cpu access_profile time_range – specifies the time range profile that has been associated with the acl entries. Delete access_id − use this to remove a previously created access rule in a p...

  • Page 278

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 278 enable cpu_interface_filtering purpose used to enable cpu interface filtering on the switch. Syntax enable cpu_interface_filtering description this command is used, in conjunction with the disable...

  • Page 280

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 280 config flow_meter pbs - (optional) specifies the “peak burst size”. The unit is in kbytes. This parameter is an optional parameter. The default value is 4kbyte. - enter the peak burst size value h...

  • Page 281

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 281 config flow_meter - enter the replace dscp value here. Drop - drops the packet. Counter - (optional) specifies the acl counter. This is optional. The default is “disable”. The resource may be limi...

  • Page 282

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 282 conform : permit replace dscp: 11 counter: enabled exceed : permit replace dscp: 22 counter: enabled violate : drop counter: disabled --------------------------------------------------------------...

  • Page 283

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 283 show time_range purpose used to display current access list table. Syntax show time_range description this command displays current time range setting. Parameters none. Restrictions none. Example ...

  • Page 284: Safeguard Engine Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 284 safeguard engine commands periodically, malicious hosts on the network will attack the switch by utilizing packet flooding (arp storm) or other methods. These attacks may increase the cpu utilizat...

  • Page 286

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 286 cpu utilization information: rising threshold : 30% falling threshold : 20% trap/log state : enabled mode : strict des-3528:admin#.

  • Page 287

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 287 filter commands (dhcp server / netbios) dhcp server screening settings this function allows you not only to restrict all dhcp server packets but also to receive any specified dhcp server packets b...

  • Page 288

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 288 config filter dhcp_server purpose dhcp server packets except those that have been ip/client mac bound will be filtered. This command is used to configure the state of the function for filtering of...

  • Page 289

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 289 success des-3528:admin# to configure the dhcp filter state: des-3528:admin# config filter dhcp_server ports 1-10 state enable command: config filter dhcp_server ports 1-10 state enable success des...

  • Page 290

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 290 des-3528:admin# config filter netbios 1-10 state enable command: config filter netbios 1-10 state enable success. Des-3528:admin# show filter netbios purpose used to display the switch settings to...

  • Page 291

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 291 show filter extensive_netbios purpose used to display the switch settings to filter netbios packets from specified ports. Syntax show filter extensive_netbios description this command will display...

  • Page 292

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 292 layer 3 cpu filter commands the l3 cpu filter commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. When the switch receives a pac...

  • Page 293

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 293 port igmp query dvmrp pim ---- ---------- -------- ----------- 1:1 disabled disabled disabled 1:2 disabled disabled disabled des-3528:admin#.

  • Page 294

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 294 loop-back detection commands the loop-back detection commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters conf...

  • Page 295

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 295 des-3528:admin# config loopdetect recover_timer 0 interval 20 mode vlan-based command: config loopdetect recover_timer 0 interval 20 mode vlan-based success des-3528:admin# config loopdetect ports...

  • Page 296

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 296 enable loopdetect purpose used to globally enable loop-back detection on the switch. Syntax enable loopdetect description this command is used to globally enable loop-back detection on the switch....

  • Page 297

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 297 des-3528:admin#show loopdetect command: show loopdetect lbd global settings --------------------------- status : disabled mode : port-based interval : 10 sec recover time : 60 sec trap state : non...

  • Page 298

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 298 des-3528:admin#.

  • Page 299

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 299 traffic segmentation commands traffic segmentation allows users to further sub-divide vlans into smaller groups of ports that will help to reduce traffic on the vlan. The vlan rules take precedenc...

  • Page 300

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 300 ---- ---------------------------- 1 1-26 2 1-26 3 1-26 4 1-26 5 1-26 6 1-26 7 1-26 8 1-26 9 1-26 10 1-26 11 1-26 12 1-26 13 1-26 14 1-26 15 1-26 16 1-26 17 1-26 18 1-26 ctrl+c esc q quit space n n...

  • Page 301: Sflow Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 301 sflow commands the sflow commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable sflow disable sflow show ...

  • Page 302

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 302 disable sflow purpose used to disable the sflow function. Syntax disable sflow description this command disables the sflow function. Parameters none. Restrictions only administrator and operator-l...

  • Page 308

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 308 success. Des-3528:admin# delete sflow analyzer_server purpose used to delete the analyzer_server. Syntax delete sflow analyzer_server description this command deletes the analyzer_server. Paramete...

  • Page 309: Time And Sntp Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 309 time and sntp commands the simple network time protocol (sntp) (an adaptation of the network time protocol (ntp)) commands in the command line interface (cli) are listed (along with the appropriat...

  • Page 311

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 311 enable sntp purpose used to enable sntp server support. Syntax enable sntp description this command enables sntp support. Sntp service must be separately configured (see config sntp ). Enabling an...

  • Page 312

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 312 to manually set system time and date settings: des-3528:admin# config time 30jul2013 16:30:30 command: config time 30jul2013 16:30:30 success. Des-3528:admin# config time_zone purpose used to dete...

  • Page 314

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 314 to configure daylight savings time on the switch: des-3528:admin# config dst repeating s_week 2 s_day tue s_mth 4 s_time 15:00 e_week 2 e_day wed e_mth 10 e_time 15:30 offset 30 command: config ds...

  • Page 315

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 315 arp and gratuitous arp commands the arp commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create arpentry c...

  • Page 316

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 316 config arpentry purpose used to configure a static entry in the arp table. Syntax config arpentry description this command is used to configure a static entry in the arp table. The user may specif...

  • Page 318

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 318 clear arptable purpose used to remove all dynamic arp table entries. Syntax clear arptable description this command is used to remove dynamic arp table entries from the switch’s arp table. Static ...

  • Page 319

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 319 config gratuitous_arp send dup_ip_detected purpose used to enable/disable the sending of gratuitous arp requests while a duplicate ip address is being detected. Syntax config gratuitous_arp send d...

  • Page 321

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 321 command: config gratuitous_arp send periodically ipif system interval 5 success. Des-3528:admin# show gratuitous arp purpose used to display gratuitous arp configuration. Syntax show gratuitous_ar...

  • Page 322: Routing Table Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 322 routing table commands the routing table commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create iproute [...

  • Page 324: Mac Notification Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 324 mac notification commands the mac notification commands in the command line interface (cli) are listed, in the following table, along with their appropriate parameters. Command parameters enable m...

  • Page 326

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 326 command: show mac_notification global mac notification settings state : enabled interval : 1 history size : 1 des-3528:admin# show mac_notification ports purpose used to display the switch’s mac a...

  • Page 327

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 327 access authentication control commands the tacacs / xtacacs / tacacs+ / radius commands allows secure access to the switch using the tacacs / xtacacs / tacacs+ / radius protocols. When a user logs...

  • Page 328

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 328 the access authentication control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable authen_policy di...

  • Page 329

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 329 enable authen_policy purpose used to enable system access authentication policy. Syntax enable authen_policy description this command will enable an administrator-defined authentication policy for...

  • Page 330

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 330 authentication policy: enabled des-3528:admin# create authen_login method_list_name purpose used to create a user-defined method list of authentication methods for user login. Syntax create authen...

  • Page 332

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 332 config authen_login none – adding this parameter will require no authentication to access the switch. Note: entering none or local as an authentication protocol will override any other authenticat...

  • Page 334

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 334 create authen_enable method_list_name purpose used to create a user-defined method list of authentication methods for promoting user's privilege to admin level. Syntax create authen_enable method_...

  • Page 336

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 336 config authen_enable local_enable − adding this parameter will require the user to be authenticated using the local user account database on the switch. The local enable password of the device can...

  • Page 339

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 339 -------------- ---------------- ----------------------- console default default telnet trinity default ssh default default http default default des-3528:admin# create authen server_host purpose us...

  • Page 342

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 342 des-3528:admin# create authen server_group purpose used to create a user-defined authentication server group. Syntax create authen server_group description this command will create an authenticati...

  • Page 344

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 344 delete authen server_group purpose used to delete a user-defined authentication server group. Syntax delete authen server_group description this command will delete an authentication server group....

  • Page 345

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 345 config authen parameter response_timeout purpose used to configure the time in second waiting for user input. Syntax config authen parameter response_timeout description this command will set the ...

  • Page 346

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 346 show authen parameter purpose used to show the authentication parameters. Syntax show authen parameter description this command will display the authentication parameters currently configured on t...

  • Page 347

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 347 config admin local_enable purpose used to configure the local enable password for administrator level privileges. Syntax config admin local_enable description this command will configure the local...

  • Page 348

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 348 secure shell (ssh) commands the steps required to use the secure shell (ssh) protocol for secure communication between a remote pc (the ssh client) and the switch (the ssh server), are as follows:...

  • Page 349

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 349 disable ssh purpose used to disable ssh. Syntax disable ssh description this command allows users to disable ssh on the switch. Parameters none. Restrictions only administrator and operator and po...

  • Page 350

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 350 show ssh authmode purpose used to display the ssh authentication mode setting. Syntax show ssh authmode description this command will allow users to display the current ssh authentication setting ...

  • Page 351

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 351 show ssh server purpose used to display the ssh server setting. Syntax show ssh server description this command allows users to display the current ssh server setting. Parameters none. Restriction...

  • Page 352

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 352 show ssh user authmode purpose used to display the ssh user setting. Syntax show ssh user authmode description this command allows users to display the current ssh user setting. Parameters none. R...

  • Page 354

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 354 aes192 : enabled aes256 : enabled arcfour : enabled blowfish : enabled cast128 : enabled twofish128 : enabled twofish192 : enabled twofish256 : enabled data integrity algorithm -------------------...

  • Page 355

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 355 secure sockets layer (ssl) commands secure sockets layer or ssl is a security feature that will provide a secure communication path between a host and client through the use of authentication, dig...

  • Page 358

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 358 success. Des-3528:admin# show ssl cachetimeout purpose used to show the ssl cache timeout. Syntax show ssl cachetimeout description this command allows the user to view the ssl cache timeout curre...

  • Page 359

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 359 command: show ssl certificate loaded with rsa certificate! Des-3528:admin# download ssl certificate purpose used to download a certificate file for the ssl function on the switch. Syntax download ...

  • Page 360

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 360 d-link single ip management commands simply put, d-link single ip management is a concept that will stack switches together over ethernet instead of using stacking ports or modules. Switches using...

  • Page 361

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 361 when a cs becomes a ms, it automatically becomes a member of the first snmp community (include read/write and read only) to which the cs belongs. However if a ms has its own ip address, it can bel...

  • Page 362

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 362 enable sim purpose used to enable single ip management (sim) on the switch syntax enable sim description this command will enable sim globally on the switch. Sim features and functions will not fu...

  • Page 364

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 364 to show the candidate information in summary, if the candidate id is specified: des-3528:admin# show sim candidates command: show sim candidates id mac address platform / hold firmware device name...

  • Page 365

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 365 example usage: to connect to the ms, with member id 2, through the cs, using the command line interface: des-3528:admin# reconfig member_id 2 command: reconfig member_id 2 des-3528:admin# login: c...

  • Page 367

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 367 to update the name of a group: des-3528:admin# config sim commander group_name trinity command: config sim commander group_name trinity success. Des-3528:admin# download sim_ms purpose used to dow...

  • Page 369: Jwac Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 369 jwac commands the japanese web-based access control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enabl...

  • Page 371

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 371 enable jwac redirect purpose used to enable jwac redirect function. Syntax enable jwac redirect description this command is for the unauthenticated host to be redirected to the quarantine server w...

  • Page 372

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 372 success. Des-3528:admin# disable jwac forcible_logout purpose used to disable jwac forcible logout function. Syntax disable jwac forcible_logout description this command is used to disable jwac fo...

  • Page 373

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 373 des-3528:admin# enable jwac quarantine_server_monitor purpose used to enable jwac quarantine server monitor. Syntax enable jwac quarantine_server_monitor description this command is for the jwac s...

  • Page 374

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 374 des-3528:admin# config jwac quarantine_server_error_timeout 60 command: config jwac quarantine_server_error_timeout 60 success. Des-3528:admin# config jwac redirect purpose used to configure redir...

  • Page 380

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 380 config jwac user purpose used to update local user db. Syntax config jwac user {vlan } description this command updates the local user db. Only the created user can be configured. Parameters − the...

  • Page 381

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 381 username password vid ---------------- ---------- ---------------- twatanabe 123 2 total entries:1 des-3528:admin# clear jwac auth_state purpose used to delete hosts on jwac enabled ports syntax c...

  • Page 382

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 382 q-srv error timeout : 30 seconds radius auth-protocol : pap authentication failover : disabled radius authorization : enabled local authorization : enabled update server :172.18.202.1/32 172.18.20...

  • Page 383

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 383 show jwac ports purpose used to display port configuration of jwac syntax show jwac ports {} description the show jwac port command allows you to display port configuration of jwac parameters – (o...

  • Page 385

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 385 command: show jwac authenticate_page current page : japanese version english page element ------------------------------------------------------------ page title : login window title : authenticat...

  • Page 386

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 386 link layer discovery protocol (lldp) commands the link layer discovery protocol (lldp) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the follow...

  • Page 387

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 387 command parameters show lldp_med local_ports {} show lldp_med ports {} show lldp_med remote_ports {} each command is listed, in detail, in the following sections. Enable lldp purpose used to enabl...

  • Page 388

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 388 config lldp purpose used to change the packet transmission interval. Syntax config lldp message_tx_interval description this interval controls how often active ports retransmit advertisements to t...

  • Page 389

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 389 config lldp purpose used to change the minimum time (delay-interval) any lldp port will delay advertising successive lldp advertisements due to a change in lldp mib content. The tx_delay defines t...

  • Page 390

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 390 to change the notification interval to 10 seconds: des-3528:admin# config lldp notification_interval 10 command: config lldp notification_interval 10 success. Des-3528:admin# config lldp ports pur...

  • Page 393

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 393 des-3528:admin# config lldp port purpose used to configure an individual port or group of ports to exclude one or more of ieee 802.1 organizationally port and protocol vlan id tlv data types from ...

  • Page 394

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 394 config lldp port purpose used to configure an individual port or group of ports to exclude one or more of ieee 802.1 organizationally protocol identity tlv data types from outbound lldp advertisem...

  • Page 395

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 395 config lldp ports purpose used to configure an individual port or group of ports to exclude one or more of ieee 802.3 organizationally specific tlv data types from outbound lldp advertisements. Sy...

  • Page 396

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 396 show lldp purpose used to display the switch’s general lldp configuration status. Syntax show lldp description this command displays the switch’s general lldp configuration status. Parameters none...

  • Page 397

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 397 show lldp ports purpose used to display the lldp per port configuration for advertisement options. Syntax show lldp ports {} description this command displays the lldp per port configuration for a...

  • Page 398

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 398 port id : 1/1 port description : d-link des-3528 r2.60.017 port 1 on unit 1 port pvid : 1 management address count : 1 ppvid entries count : 0 vlan name entries count : 1 protocol identity entries...

  • Page 399

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 399 show lldp statistics purpose used to display the system lldp statistics information. Syntax show lldp statistics description this command displays an overview of neighbor detection activity on the...

  • Page 400

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 400 config lldp_med fast_start repeat_count purpose this command is used to configure the fast start repeat count. Syntax config lldp_med fast_start repeat_count description when an lldp-med capabilit...

  • Page 401

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 401 config lldp_med notification topo_change ports purpose this command is used to enable or disable each port for sending topology change notification to configured snmp trap receiver(s) if an endpoi...

  • Page 402

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 402 des-3528:admin#config lldp_med ports 1:1-1:2 med_transmit_capabilities all state enable command: config lldp_med ports 1:1-1:2 med_transmit_capabilities all state enable success. Des-3528:admin# s...

  • Page 403

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 403 ----------------------------------------------------------------- lldp-med capabilities support: capabilities :support network policy :support location identification :not support extended power v...

  • Page 404

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 404 remote entities count : 1 entity 1 chassis id subtype : mac address chassis id : 00-01-02-03-04-00 port id subtype : net address port id : 172.18.10.11 lldp-med capabilities: lldp-med device class...

  • Page 405: Q-In-Q Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 405 q-in-q commands the q-in-q commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable qinq disable qinq show ...

  • Page 406

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 406 disable qinq purpose used to disable the q-in-q mode. Syntax disable qinq description this command disables the q-in-q mode. All dynamically learned l2 address will be cleared. All dynamically reg...

  • Page 408

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 408 port id: 1 --------------------------------------------------------- role: nni miss drop: disabled outer tpid: 0x8100 use inner priority: disabled add inner tag: disabled port id: 2 --------------...

  • Page 411: Rspan Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 411 rspan commands the remote switched port analyzer (rspan) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ...

  • Page 415

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 415 static mac-based vlan commands the static mac-based vlan commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ...

  • Page 416

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 416 des-3528:admin# delete mac_based_vlan mac_address 00-00-00-00-00-01 vlan default command: delete mac_based_vlan mac mac_address 00-00-00-00-00-01 vlan default success. Des-3528:admin# show mac_bas...

  • Page 417: Simple Red Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 417 simple red commands the simple red commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable sred disable sr...

  • Page 419

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 419 des-3528:admin# show sred purpose used to display the simple red configure parameter. Syntax show sred { { }} description this command displays the current threshold(per port and per queue) parame...

  • Page 422

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 422 dscp to color mapping port 1 dscp 0 – 7 is mapped to green dscp 8 – 15, 17 is mapped to yellow dscp 16, 18 – 63 is mapped to red des-3528:admin# config 802.1p map purpose used to configure mapping...

  • Page 423

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 423 12 green green green green green green green green 13 green green green green green green green green 14 green green green green green green green green 15 green green green green green green gree...

  • Page 424

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 424 mac-based access control commands the mac-based access control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command param...

  • Page 425

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 425 enable mac_based_access_control purpose used to enable mac-based access control. Syntax enable mac_based_access_control description this command will enable the mac-based ac function. Parameters n...

  • Page 428

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 428 des-3528:admin# config mac_based_access_control log state purpose this command is used to enable or disable generating of mac-based access control logs. Syntax config mac_based_access_control log ...

  • Page 433

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 433 show mac_based_access_control auth_state ports purpose used to display mac_based_access_control authentication status. Syntax show mac_based_access_control auth_state ports {} description this com...

  • Page 435

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 435 web-based access control commands the web-based access control commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command param...

  • Page 436

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 436 disable wac purpose used to disable the wac function. Syntax disable wac description this command will disable the wac function. Parameters none. Restrictions only administrator and operator and p...

  • Page 437

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 437 success. Des-3528:admin# config wac default_redirpath purpose used to config wac default redirect path. Syntax config wac default_redirpath description if the default redirect path is configured, ...

  • Page 440

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 440 show wac auth_state purpose used to display the authentication state of a port. Syntax show wac auth_state ports {} description used to display the authentication state for ports. If port 1 is in ...

  • Page 442

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 442 state : enable method : local authentication failover : disabled redirect path : virtual ip : 0.0.0.0 switch http port : 80 (http) radius authorization : enabled local authorization : enabled des-...

  • Page 444

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 444 power over ethernet (poe) commands the power over ethernet (poe) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command par...

  • Page 445

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 445 des-3528p:admin# config poe system power_limit 250 power_disconnect_method deny_low_priority_port command: config poe system power_limit 250 power_disconnect_method deny_low_priority_port success....

  • Page 447

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 447 des-3528p:admin# config poe ports 5 state enable priority critical power_limit user_define 1000 command: config poe ports 5 state enable priority critical power_limit user_define 1000 power limit ...

  • Page 448

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 448 3 enabled critical 4200 (class 1) 0 0 0 0 off : interim state during line detection 4 enabled critical 4200 (class 1) 0 0 0 0 off : interim state during line detection 5 enabled critical 4200 (cla...

  • Page 449

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 449 pppoe circuit id insertion commands the pppoe circuit id insertion commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command p...

  • Page 454: Policy Route Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 454 policy route commands the policy route commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create policy_rout...

  • Page 456

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 456 show policy_route purpose used to display policy route rule. Syntax show policy_route description this command is used to display policy route rule. Parameters none. Restrictions none. Example usa...

  • Page 457

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 457 bpdu attack protection commands the bpdu attack protection commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Note: the bpdu at...

  • Page 459

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 459 enable bpdu_protection purpose used to enable bpdu attack protection globally. Syntax enable bpdu_protection description this command allows the bpdu attack protection to be globally enabled on th...

  • Page 460

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 460 to display the bpdu attack protection status for ports 1-4 of the switch: des-3528:admin# show bpdu_protection ports 1-4 command: show bpdu_protection ports 1-4 port state mode status ------ -----...

  • Page 461: Ethernet Oam Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 461 ethernet oam commands the ethernet oam commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config ethernet_oa...

  • Page 464

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 464 des-3528:admin# config ethernet_oam ports 1 link_monitor error_frame_seconds threshold 2 window 10000 notify_state enable command: config ethernet_oam ports 1 link_monitor error_frame_seconds thre...

  • Page 467

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 467 show ethernet_oam ports status purpose used to show primary controls and status information for ethernet oam. Syntax show ethernet_oam ports {} status description this command is used to show prim...

  • Page 468

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 468 remote loopback : supported unidirection : supported link monitoring : supported variable request : not supported pdu revision : 0 operation status : disable loopback status : no loopback there is...

  • Page 469

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 469 show ethernet_oam ports statistics purpose used to show ethernet oam statistics. Syntax show ethernet_oam ports {} statistics description this command is used to show ports ethernet oam statistics...

  • Page 470

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 470 local event statistics error symbol event : 0 error frame event : 0 error frame period event : 0 errored frame seconds event : 0 dying gasp : 0 critical event : 0 remote event statistics error sym...

  • Page 471: Dhcp Server Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 471 dhcp server commands the dhcp server commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create dhcp excluded...

  • Page 472

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 472 create dhcp excluded_address purpose used to specify the ip addresses that the dhcp server will not assign to dhcp client. Syntax create dhcp excluded_address begin_address end_address description...

  • Page 473

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 473 des-3528:admin# show dhcp excluded_address command: show dhcp excluded_address index begin address end address ----- ------------ ------------ 1 10.10.10.1 10.10.10.10 total entries: 1 des-3528:ad...

  • Page 474

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 474 config dhcp pool network_addr purpose used to specify the network for the dhcp pool. Syntax config dhcp pool network_addr description this command specifies the network for the dhcp pool. The addr...

  • Page 475

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 475 config dhcp pool dns_server purpose used to specify the ip address of a dns server that is available to a dhcp client. Up to three ip addresses can be specified in one command line. Syntax config ...

  • Page 478

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 478 config dhcp pool next_server purpose used to specify the next server to be used in the dhcp client boot process. Syntax config dhcp pool next_server {} description the next server used by the dhcp...

  • Page 479

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 479 to configure the timeout value for ping packets: des-3528:admin# config dhcp ping_timeout 100 command: config dhcp ping_timeout 100 success. Des-3528:admin# create dhcp pool manual_binding purpose...

  • Page 480

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 480 delete dhcp pool manual_binding purpose used to s pecify the distinct identification of the client in dotted-hexadecimal notation or hardware address to delete. Syntax delete dhcp pool manual_bind...

  • Page 481

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 481 des-3528:admin# show dhcp binding accounting command: show dhcp binding accounting pool name ip address hardware address type status lifetime ----------- -------------- ---------------- ------- --...

  • Page 482

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 482 des-3528:admin# enable dhcp_server purpose used to enable the dhcp server function. Syntax enable dhcp_server description if the dhcp relay is enabled, the dhcp server cannot be enabled. The oppos...

  • Page 484: Cable Diagnostics Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 484 cable diagnostics commands the cable diagnostics commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters cable_di...

  • Page 485

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 485 connectivity fault management commands the connectivity fault management commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Com...

  • Page 492

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 492 des-3528:admin# enable cfm purpose used to enable cfm globally. Syntax enable cfm description this command is used to enable cfm globally. Parameters none. Restrictions only administrator and oper...

  • Page 493

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 493 command: config cfm ports 2-5 state enable success. Des-3528:admin# show cfm ports purpose used to show cfm state of specified ports. Syntax show cfm ports description cfm state of speicified port...

  • Page 494

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 494 md level : 2 mip creation: explicit senderid tlv: none vid ma name ---- ---------- 1 op1 des-3528:admin# example usage: to display cfm mep: des-3528:admin#show cfm mepname mep command: show cfm me...

  • Page 498

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 498 des-3528:admin# show cfm linktrace mepname op-mep4 command: show cfm linktrace mepname op-mep4 trans id source mep dstination -------- ---------------- ----------------- des-3528:admin# show cfm l...

  • Page 500

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 500 request timed out. Cfm loopback statistics for 00-01-02-03-04-05: packets: sent=4, received=1, lost=3(75% loss). Des-3528:admin# show cfm pkt_cnt purpose used to show cfm packet rx/tx counters. Sy...

  • Page 502

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 502 cfm lock md purpose this command is used to start/stop cfm management lock. This command will result in the mep sends a lck pdu to client level mep. Syntax cfm lock md ma mepid remote_mepid 8191> ...

  • Page 505: Command History Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 505 command history commands the switch history commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters ? Config comm...

  • Page 506

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 506 config stp instance_id config stp mst_config_id config stp mst_ports config stp ports config stp priority config stp version des-3528:admin# config command_history purpose used to configure the co...

  • Page 507

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 507 arp spoofing prevention commands the arp spoofing prevention commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command paramet...

  • Page 508

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 508 to display the arp spoofing prevention entries: des-3528:admin#show arp_spoofing_prevention command: show arp_spoofing_prevention arp spoofing prevention table gateway ip address gateway mac addre...

  • Page 509: Auto-Configuration Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 509 auto-configuration commands the auto-configuration commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable...

  • Page 510

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 510 des-3528 fast ethernet switch command line interface firmware: build 3.00.012 copyright(c) 2013 d-link corporation. All rights reserved. Des-3528:admin# des-3528:admin# des-3528:admin# download co...

  • Page 511

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 511 show autoconfig purpose this command is used to display if the auto-configuration is enabled or disabled. Syntax show autoconfig description this command is used to display if the auto-configurati...

  • Page 512

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 512 compound authentication commands the compound authentication commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command paramet...

  • Page 514

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 514 config authentication mac_format purpose this command will set the mac address format that will be used for authentication username via the radius server. Syntax config authentication mac_format {...

  • Page 516

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 516 show authentication guest_vlan purpose this command is used to show guest vlan setting. Syntax show authentication guest_vlan description this command is used to show guest vlan setting. Parameter...

  • Page 517

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 517 enable authorization purpose this command is used to enable authorization. Syntax enable authorization attributes description this command is used to enable authorization. Parameters none. Restric...

  • Page 519

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 519 des-3528:admin#show authentication mac_format command: show authentication mac_format case : uppercase delimiter : none delimiter number : 5 des-3528:admin#.

  • Page 520: Debug Software Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 520 debug software commands the debug software commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters debug error_lo...

  • Page 521

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 521 ->8018c814 ->8028ff44 ->8028352c ->801d703c ->8013b8a4 ->802ae754 ->802a5e0c to clear the error log: des-3528:admin# debug error_log clear command: debug error_log clear success. Des-3528:admin# t...

  • Page 522

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 522 des-3528:admin# debug buffer clear command: debug buffer clear success. Des-3528:admin# to upload the messages stored in debug buffer to tftp server: des-3528:admin# debug buffer upload_totftp 10....

  • Page 523

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 523 command: debug config all disable success. Des-3528:admin# debug config error_reboot purpose this command is used to set if the switch needs to be rebooted when a fatal error occurs. Syntax debug ...

  • Page 525: Dhcpv6 Client Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 525 dhcpv6 client commands the dhcpv6 client commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config ipif [{ip...

  • Page 526

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 526 des-3528:admin# debug dhcpv6_client state enable command: debug dhcpv6_client state enable success. Des-3528:admin# debug dhcpv6_client output purpose used to set debug message to output to buffer...

  • Page 527: Dhcpv6 Relay Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 527 dhcpv6 relay commands the dhcpv6 relay commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config dhcpv6_rela...

  • Page 530

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 530 des-3528:admin#show dhcpv6_relay command: show dhcpv6_relay dhcpv6 relay global state : enabled dhcpv6 hops count limit : 4 --------------------------------------------------------------- ip inter...

  • Page 532

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 532 des-3528:admin# debug dhcpv6_relay hop_count state enable command: debug dhcpv6_relay hop_count state enable success. Des-3528:admin#.

  • Page 533: Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 533 d-link unidirectional link detection (duld) commands the d-link unidirectional link detection (duld) commands in the command line interface (cli) are listed (along with the appropriate parameters)...

  • Page 534

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 534 show duld purpose this command is used to show unidirectional link detection information. Syntax show duld ports {} description this command is used to show unidirectional link detection informati...

  • Page 535: Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 535 ethernet ring protection switching (erps) commands the ethernet ring protection switching (erps) commands in the command line interface (cli) are listed (along with the appropriate parameters) in ...

  • Page 536

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 536 des-3528:admin# enable erps command: enable erps success. Des-3528:admin# disable erps purpose this command is used to disable the global erps function on a switch. Syntax disable erps description...

  • Page 537

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 537 des-3528:admin# delete erps raps_vlan 4094 command: delete erps raps_vlan 4094 success. Des-3528:admin# config erps raps_vlan ring mel purpose this command is used to configure the ring mel for an...

  • Page 538

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 538 des-3528:admin# config erps raps_vlan 4094 ring_port west 5 command: config erps raps_vlan 4094 ring_port west 5 success. Des-3528:admin# config erps raps_vlan rpl_port purpose this command is use...

  • Page 539

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 539 des-3528:admin# config erps raps_vlan 4094 rpl_owner enable command: config erps raps_vlan 4094 rpl_owner enable success. Des-3528:admin# config erps raps_vlan protected_vlan purpose this command ...

  • Page 542

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 542 current ring state : idle ------------------------ r-aps vlan : 4093 ring status : enabled west port : virtual channel east port : 10 (forwarding) rpl port : none rpl owner : disabled protected vl...

  • Page 544

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 544 config erps raps_vlan sub_ring raps_vlan tc_propagation state purpose this command is used to configure the state of topology change propagation for the sub-ring. Syntax config erps raps_vlan sub_...

  • Page 545

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 545 ipv6 neighbor discover commands the ipv6 neighbor discover commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter...

  • Page 546

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 546 delete ipv6 neighbor_cache purpose delete a neighbor cache entry or static neighbor cache entries from the address cache or all address cache entries on this ip interface. Syntax delete ipv6 neigh...

  • Page 547

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 547 des-3528:admin#show ipv6 neighbor_cache ipif system all command: show ipv6 neighbor_cache ipif system all neighbor link layer address interface state -------------------------------------- -------...

  • Page 548

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 548 des-3528:admin# config ipv6 nd ns ipif system retrans_time 1000000 command: config ipv6 nd ns ipif system retrans_time 1000000 success. Des-3528:admin# show ipv6 nd purpose used to display informa...

  • Page 549: Ipv6 Route Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 549 ipv6 route commands the ipv6 route commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create ipv6route [defa...

  • Page 551

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 551 layer 2 protocol tunneling (l2pt) commands the layer 2 protocol tunneling (l2pt) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following ta...

  • Page 552

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 552 des-3528:admin# config l2protocol_tunnel ports 1-4 type uni tunneled_protocol stp command: config l2protocol_tunnel ports 1-4 type uni tunneled_protocol stp success. Des-3528:admin# show l2protoco...

  • Page 553

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 553 enable l2protocol_tunnel purpose used to enable the layer 2 protocol tunneling function. Syntax enable l2protocol_tunnel description used to enable the layer 2 protocol tunneling function. Paramet...

  • Page 554: Local Route Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 554 local route commands the local route commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable local_route [...

  • Page 555

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 555 show local_route purpose this command is used to display the local route configuration. Syntax show local_route description the show local route command displays the local route configuration. Par...

  • Page 556

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 556 mstp debug enhancement commands the mstp debug enhancement commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter...

  • Page 557

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 557 debug stp show information purpose this command used to display stp detailed information, such as the hardware tables, the stp state machine, etc. Syntax debug stp show information description thi...

  • Page 558

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 558 ---------------------------------------------------------- 1 disabled disabled disabled 2 disabled disabled disabled 3 disabled disabled disabled 4 disabled disabled disabled 5 disabled disabled d...

  • Page 562

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 562 show technical support commands the show technical support commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameter...

  • Page 563

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 563 des-3528:admin# show tech_support command: show tech_support #------------------------------------------------------------------------------- # des-3528 fast ethernet switch # technical support in...

  • Page 564

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 564 upload tech_support_totftp purpose the upload tech_support_totftp command is used to upload the information of technique’s support to tftp server. Syntax upload tech_support_totftp description the...

  • Page 567: Vlan Counter Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 567 vlan counter commands the vlan counter commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters create vlan_counte...

  • Page 570: Power Saving Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 570 power saving commands the power saving commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config power_savin...

  • Page 571

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 571 des-3528:admin#config power_saving state enable command: config power_saving state enable success. Des-3528:admin# config power_saving hibernation purpose this command is used to add or delete the...

  • Page 572

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 572 des-3528:admin#config power_saving hibernation delete time_range range_2 command: config power_saving hibernation delete time_range range_2 success. Des-3528:admin# config power_saving led purpose...

  • Page 573

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 573 des-3528:admin#config power_saving led delete time_range range_2 command: config power_saving led delete time_range range_2 success. Des-3528:admin# config power_saving port purpose this command i...

  • Page 574

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 574 des-3528:admin#config power_saving port 1:1 delete time_range range_2 command: config power_saving port 1:1 delete time_range range_2 success. Des-3528:admin# config power_saving mode purpose this...

  • Page 575

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 575 des-3528:admin#config power_saving mode port hibernation enable command: config power_saving mode port hibernation enable success. Des-3528:admin# show power_saving purpose this command is used to...

  • Page 576

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 576 des-3528:admin#show power_saving hibernation command: show power_saving hibernation power saving configuration on system hibernation ---------------------------------------------------- state: ena...

  • Page 577

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 577 des-3528:admin#show power_saving length_detection command: show power_saving length_detection length detection state: enabled des-3528:admin# config led state purpose this command is used to confi...

  • Page 578

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 578 digital diagnostic monitoring (ddm) commands the digital diagnostic monitoring (ddm) commands in the command line interface (cli) are listed (along with the appropriate parameters) in the followin...

  • Page 579

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 579 to configure ddm log state to enable: des-3528:admin#config ddm log enable command: config ddm log enable success. Des-3528:admin# to configure ddm trap state to enable: des-3528:admin#config ddm ...

  • Page 580

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 580 config ddm ports low_warning - (optional) specify the low threshold for the warning. When the operating parameter falls below this value, the action associated with the warning is taken. - enter t...

  • Page 581

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 581 config ddm ports reload_threshold - specify to reload the ddm threshold configuration. Restrictions only administrator and operator-level users can issue this command. Example usage:.

  • Page 582

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 582 to configure the port 25’s temperature threshold: des-3528:admin#config ddm ports 1:25 temperature_threshold high_alarm 84.9555 low_alarm -10 high_warning 70 low_warning 2.25251 command: config dd...

  • Page 583

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 583 des-3528:admin#config ddm ports 1:25 reload_threshold command: config ddm ports 1:25 reload_threshold success. Des-3528:admin# config ddm power_unit purpose the command is used to configure the un...

  • Page 584

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 584 to display the ddm global settings: des-3528:admin#show ddm command: show ddm ddm log : enabled ddm trap : enabled ddm tx/rx power unit : dbm des-3528:admin# show ddm ports purpose this command is...

  • Page 585: Command Logging Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 585 command logging commands the command logging commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters enable comma...

  • Page 586

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 586 show command logging purpose this command displays the switch’s general command logging configuration status. Syntax show command logging description this command displays the switch’s general com...

  • Page 587: Udp Helper Commands

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 587 udp helper commands the udp helper commands in the command line interface (cli) are listed (along with the appropriate parameters) in the following table. Command parameters config udp_helper add ...

  • Page 588

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 588 des-3528:admin#config udp_helper delete ipif system 20.0.0.90 command: config udp_helper delete ipif system 20.0.0.90 success. Des-3528:admin# config udp_helper udp_port add purpose this command i...

  • Page 589

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 589 des-3528:admin#config udp_helper udp_port delete 55 command: config udp_helper udp_port delete 55 success. Des-3528:admin# enable udp_helper purpose this command is used to enable the udp helper f...

  • Page 590

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 590 des-3528:admin#show udp_helper command: show udp_helper udp helper status : enabled application udp port ------------ --------------- user app1 55 interface server ------------ --------------- sys...

  • Page 591

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 591 appendix a - password recovery procedure this document describes the procedure for resetting passwords on d-link switches. Authenticating any user who tries to access networks is necessary and imp...

  • Page 592

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 592 appendix b - system log entries the following table lists all possible entries and their corresponding meanings that will appear in the system log. Category event description log information sever...

  • Page 593

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 593 login failed through telnet login failed through telnet (username: , ip: ) warning logout through telnet logout through telnet (username: , ip: ) informational telnet session timed out telnet sess...

  • Page 594

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 594 successful login through telnet authenticated by aaa none method successful login through telnet from authenticated by aaa none method (username: ) informational successful login through ssh authe...

  • Page 595

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 595 successful enable admin through ssh authenticated by aaa none method successful enable admin through ssh from authenticated by aaa none method (username: ) informational successful enable admin th...

  • Page 596

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 596 safeguard engine is in filtering packet mode safeguard engine enters exhausted mode warning packet storm broadcast storm occurrence port broadcast storm is occurring warning broadcast storm cleare...

  • Page 597

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 597 ip and password changed ip address change activity unit ,management ip address was changed by (username: ) //console unit ,management ip address was changed by (username: ,ip:)//remote information...

  • Page 598

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 598 appendix c - trap entries trap name/oid variable bind format mib name severity coldstart 1.3.6.1.6.3.1.1.5.1 none rfc1907 (snmpv2-mib) warning warmstart 1.3.6.1.6.3.1.1.5.2 none rfc1907 (snmpv2-mi...

  • Page 599

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 599 1.3.6.1.4.1.171.12.23.5.0.1 1.3.6.1.4.1.171.12.23.3.2.1.1 swipmacbindingviolationip 1.3.6.1.4.1.171.12.23.5.2.1 swipmacbindingviolationmac 1.3.6.1.4.1.171.12.23.5.2.2 mib agentgratuitousarptrap 1....

  • Page 600

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 600 1.3.6.1.4.1.171.12.37.100.2.2 swportloopoccurred 1.3.6.1.4.1.171.12.41.10.0.1 swloopdetectportindex 1.3.6.1.4.1.171.12.41.3.1.1.1 loopback- detect-mib warning swportlooprestart 1.3.6.1.4.1.171.12....

  • Page 601

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 601 1.3.6.1.4.1.171.12.11.2.2.3.0.2 1.3.6.1.4.1.171.12.11.1.7.1.1 swfanid 1.3.6.1.4.1.171.12.11.1.7.1.2 swpowerstatuschg 1.3.6.1.4.1.171.12.11.2.2.2.0.1 swpowerunitindex 1.3.6.1.4.1.171.12.11.1.6.1.1 ...

  • Page 602

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 602 ifindex 1.3.6.1.2.1.2.2.1.1 swsingleipmslinkup 1.3.6.1.4.1.171.12.8.6.0.14 swsingleipmsid 1.3.6.1.4.1.171.12.8.1.3.1.1 swsingleipmsmacaddr 1.3.6.1.4.1.171.12.8.1.3.1.3 ifindex 1.3.6.1.2.1.2.2.1.1 ...

  • Page 603

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 603 appendix d - radius attributes assignment the radius attributes assignment on the switch is used in the following modules: 802.1x (port-based and host- based), japanese web-based access control, w...

  • Page 604

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 604 if the user has configured the 802.1p priority attribute of the radius server (for example, priority 7) and the 802.1x, or mac based authentication is successful, the device will assign the 802.1p...

  • Page 605

    Xstack® des-3528/des-3552 series layer 2 managed stackable fast ethernet switch cli reference guide 605 if the user has configured the vlan attribute of the radius server (for example, vid 3) and the 802.1x, mac based access control, or wac authentication is successful, the port will be assigned to ...