D-Link DPH-80 User Manual

Other manuals for DPH-80: Manual, User Manual
Manual is about: D-link DPH-80: User Guide

Summary of DPH-80

  • Page 1

    Dph-80 ip phone user’s guide.

  • Page 2

    Warranty and registration trademarks copyright © 2001 d-link corporation. Contents subject to change without prior notice. D-link is a registered trademark of d-link corporation/d-link systems, inc. All other trademarks belong to their respective proprietors. Copyright statement no part of this publ...

  • Page 3

    Dph-80 phone user manual warranty and registration d-link's sole obligation under this software warranty shall be to replace any defective software product with product which substantially conforms to d-link's applicable product documentation. Purchaser assumes responsibility for the selection of ap...

  • Page 4

    Dph-80 phone user manual warranty and registration limitation of warranties if the d-link product does not operate as warranted above, the customer's sole remedy shall be, at d-link's option, repair or replacement. The foregoing warranties and remedies are exclusive and are in lieu of all other warr...

  • Page 5

    Dph-80 phone user manual table of contents table of contents warranty and registration ....................................................................................1 introduction ..............................................................................................................5 fe...

  • Page 6

    Dph-80 phone user manual introduction introduction the d-link dph-80 is a fully featured ethernet business phone that allows both business and residential customers to benefit from ip telephony services. It reduces costs by receiving local and long distance voice services and data services over a si...

  • Page 7

    Dph-80 phone user manual features features • ip address assignment using dhcp (dynamic host configuration protocol) pppoe(ppp over ethernet)or static configuration • silence suppression and comfort noise generation that make the user feel natural when connected • adaptive jitter buffer for smooth vo...

  • Page 8

    Dph-80 phone user manual installation installation unpacking open the shipping carton and carefully remove all items. In addition to this user's guide, make sure you have received all of the following items: • ip phone • handset • handset cord • power adapter if any item appears to be missing or dam...

  • Page 9

    Dph-80 phone user manual basic configuration • in the general tab, click on internet protocol (tcp/ip). 8.

  • Page 10

    Dph-80 phone user manual basic configuration • click on use the following ip address, and enter a value in the 10.1.1.Xx range. (do not use the ip address 10.1.1.80; that address is already in use by the dph-80 as a default address.) if necessary, change the subnet mask and the default gateway to ma...

  • Page 11

    Dph-80 phone user manual final configuration • make sure use a proxy server is disabled. • click ok. Final configuration the dph-80 is highly versatile and can be configured to operate in any of the three main internet telephony protocols – mcgp, sip, and h.323. Please choose the appropriate protoco...

  • Page 13: Appendix B

    Appendix b dph-80 sip (session initiation protocol) ip phone configuration infrastructure requirements though the dph-80 sip phone will work in any type of lan network, a 100mbps, switched network is more suitable for providing good quality voice communications. Sip phones need a proxy or redirect s...

  • Page 14

    Dph-80 phone user manual configuring the sip phone login page to ip phone the following two parameters control access to the sip phone. Default value for both will be "dlink". These values can be changed later using the change login name and password page. User name:this is case-insensitive with a m...

  • Page 15

    Dph-80 phone user manual configuring the sip phone configuration main page click on general configuration. A new page containing information about your system and the dph-80 will appear. General configuration firmware version : it shows the current firmware version of the ip phone. It is updated whe...

  • Page 16

    Dph-80 phone user manual configuring the sip phone ppp password: this is the password used for ppp authentication with the ppp server while obtaining an ip address via pppoe. Idle timeout: this is the time interval in seconds of session inactivity after which the ppp session should be terminated. If...

  • Page 17

    Dph-80 phone user manual configuring the sip phone upload filename (up to 6 characters): this is the filename to upload the configuration parameters from the phone to the tftp server. It may be 6 characters long at maximum. It should start with a letter and should consist of digits, letters and unde...

  • Page 18

    Dph-80 phone user manual sip configuration sip configuration user name: the user name is used to identify the caller for display purposes only. It should be maximum 20 characters and should comprise only letters, digits, hyphen and/or underscore. Authentication password: this is used in authenticati...

  • Page 19

    Dph-80 phone user manual sip configuration proxy domain name: this is the name of the domain where the ip phone and the proxy/redirect are being hosted. If the field is included it will be used, instead of proxy ip address, in all sip messages including registration and authentication messages. Outb...

  • Page 20

    Dph-80 phone user manual sip configuration rtp statistics this is an informational page and shows the rtp statistical data from the current call and the previous call. This page is refreshed every 5 seconds automatically. Packets received: number of packets that have been received for the call. Pack...

  • Page 21

    Dph-80 phone user manual sip configuration on clicking yes the following screen will appear. You will be returned to the main page. Configuration upload 20

  • Page 22

    Dph-80 phone user manual sip configuration when clicked, this link will display a warning page. Click ‘yes’ to upload the configuration parameters from the phone to the tftp server as the upload filename. The tftp server and filename are set in the general configuration. Click ‘no’ on the warning pa...

  • Page 23

    Dph-80 phone user manual sip configuration the tftp server and filename are set in the general configuration. Click ‘no’ on the warning page to return to the main page. Change login name and password existing user name: this is the user name that was used to access the mgcp phone from the web browse...

  • Page 24

    Dph-80 phone user manual sip configuration save and restart when clicked, this link will display a warning page. Click ‘yes’ to save all the updated parameters to the flash memory and restart the phone so that the latest changes take effect. The you have been successfully logged out page will be dis...

  • Page 25

    Dph-80 phone user manual using the sip phone when clicked, this link will display a warning page. Click ‘yes’ to reset the phone to factory defaults and automatically restart. Click ‘no’ on the warning page to return to the main page. Logout when clicked, the you have been successfully logged out pa...

  • Page 26

    Dph-80 phone user manual using the sip phone • mute (red): steady on to indicate mute status; off means normal tones d-link sip phone plays the following tones depending on phone current state. D-link sip supports different type of tones for different country selected through configuration. • dial t...

  • Page 27

    Dph-80 phone user manual sip troubleshooting phone book: this feature allows the phone to be used without a sip server. A set of 10 numbers can be programmed to the phone and the phone will directly contact these numbers without the help of sip server. Remote diagnosis: the sip phone will send statu...

  • Page 28

    Dph-80 phone user manual sip production test voice quality is not good: the sip phone supports packet loss and network jitter to some extend. Above these levels, the quality can be bad. The g.729 codec will have better performance over the g.711 codec and it can be selected in the configuration. Cal...

  • Page 29

    Dph-80 phone user manual sip production test led test this is the first test that is performed. This tests the leds. In this test, the three leds – mute(red), hold(red) and speaker(green) – glow simultaneously for a few seconds and then turn off. No tone is played for this test, as the sip phone can...