1. DL manuals
  2. D-Link
  3. Switch
  4. DXS-3600-32S
  5. Reference Manual

D-Link DXS-3600-32S Reference Manual

Other manuals for DXS-3600-32S: Manual
Manual is about: CLI Guide

Summary of DXS-3600-32S

  • Page 2

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide i information in this document is subject to change without notice. Reproduction of this document in any manner whatsoever, without the written permission of the d-link corporation, is strictly forbidden. Trademarks used in this text: d-link...

  • Page 3: Intended Readers

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide ii intended readers the dxs-3600-32s web ui reference guide contains detailed information about the web user interface of the switch in this series. This manual is intended for advanced level users that are familiar with network management c...

  • Page 4: Safety Cautions

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide iii safety cautions to greatly reduce the risk of physical injury, electrical shock, fire, and damage to equipment, observe the following precautions. Observe and follow service markings. • do not attempt to service any product, except when ...

  • Page 5

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide iv • 115v/60hz is used mostly in north and south america as well as far eastern countries like as south korea and taiwan • 100v/50hz is used mostly in eastern japan and 100v/60hz in western japan • 230v/50hz is used mostly in europe, the mid...

  • Page 6: Table of Contents

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide table of contents intended readers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ii typographical conventions. . . . . . . . . . . . . . . . . ...

  • Page 7: Management Options

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 2 web-based switch configuration management options connecting using the web user interface management options this switch provides multiple access platforms that can be used to configure, manage and monitor networking features available on ...

  • Page 8: Areas of The User Interface

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 3 figure 2-2 enter network password window as there is no default user name or password, click ok to proceed. This will open the web-based user interface. The switch management features available in the web-based manager are explained below....

  • Page 9

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 4 on this page we will find three main areas to observe. Area number function area 1 this area displays graphical, real-time images of some of the hardware features run- ning on this switch. Some of the features that can be monitored here ar...

  • Page 10: Switch Status

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 5 switch status device information temperature status cpu status system log entries fan status flash, sd card, and memory status after clicking on the switch status link, found in the menu, the following page will be displayed:.

  • Page 11: Device Information

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 6 device information in the device information section, the user can view a list of basic information regarding the switch. In the device information section, the following display parameters are available: parameter description ip address h...

  • Page 12: Temperature Status

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 7 temperature status in the temperature section, the user can view a real-time display of the switch’s internal temperature. The temperature of the switch is mainly influenced by two factors: (1) the enviroment, and (2) the internal air-flow...

  • Page 13: Cpu Status

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 8 cpu status in the cpu section, the user can view a real-time display of the switch’s cpu usage. There are a number of factors that can influance a depleted cpu usage. One of those factors are network broadcasts. In the cli reference guide ...

  • Page 14: System Log Entries

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 9 system log entries in the system log section, the user can view a list of system log entries, generated by the switch, when certain events have occured. In the system log section, the following display parameters are available: click the m...

  • Page 15

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 10

  • Page 16: Fan Status

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 11 fan status in the fan section, the user can view a real-time display of the switch’s fan(s) status. A maximum of 3 fans can be installed in this switch. In this real-time graphic, we observe the status and speed of the three fans installe...

  • Page 17

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 12 flash, sd card, and memory status in this section, the user can view a real-time graphic that represents the memory usage for the flash, sd card, and ram memory. In this section, the following display parameters are available: parameter d...

  • Page 18: Traffic Monitoring

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 13 traffic monitoring traffic monitoring by direction traffic monitoring by type traffic monitoring by size traffic monitoring by error after clicking on the traffic monitoring link, found in the menu, the following pages will be displayed. ...

  • Page 19: Traffic Monitoring By Type

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 14 traffic monitoring by type this page can be used to monitor traffic, per-port, of a certain type. After selecting a port number and then selecting the type option, from the drop-down menu, click the apply button to view the page below: th...

  • Page 20: Traffic Monitoring By Size

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 15 traffic monitoring by size this page can be used to monitor traffic, per-port, of a certain packet size. After selecting a port number and then selecting the size option, from the drop-down menu, click the apply button to view the page be...

  • Page 21: Traffic Monitoring By Error

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 16 traffic monitoring by error this page can be used to monitor traffic, per-port, of a certain error type and direction. After selecting a port number and then selecting the error option, from the drop-down menu, click the apply button to v...

  • Page 22: Management

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 17 management download firmware download configuration upload firmware upload configuration on the management page, the user is allowed to download and upload firmware or configuration files. Keeping the switch’s firmware up-to-date will pre...

  • Page 23: Download Configuration

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 18 the following parameters can be configured in this section: click the download button to initiate the download. Download configuration in the download configuration section, the following can be seen: the following parameters can be confi...

  • Page 24

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 19 the following parameters can be configured in this section: click the upload button to initiate the upload. Parameter description source file enter the location and name of the source file for the upload..

  • Page 25

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 20 appendix a - password recovery procedure this section describes the procedure for resetting passwords on the d-link dxs-3600-32s switch. Authenticating any user who tries to access networks is necessary and important. The basic authentica...

  • Page 26

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 21 appendix b - system log entries the following table lists all possible entries and their corresponding meanings that will appear in the system log of this switch. Category log description severity note ip directed- broadcast event descrip...

  • Page 27

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 22 event description: configuration successfully downloaded. Log message: [tftp(5):]configuration successfully downloaded by (username: , ip: , mac: ) parameters description: session: the user’s session. Username: represent current login use...

  • Page 28

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 23 event description: attack log message successfully uploaded. Log message: [tftp(13):]attack log message successfully uploaded by (username: , ip: , mac: ) parameters description: session: the user’s session. Username: represent current lo...

  • Page 29

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 24 event description: port link down. Log message: port link down parameters description: portnum: 1.Interger value;2.Represent the logic port number of the device. Informational 802.1x event description: 802.1x authentication failure. Log m...

  • Page 30

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 25 event description: 802.1p default priority assigned from radius server after radius client is authenticated by radius server successfully. This 802.1p default priority will be assigned to the port. Log message: radius server assigned 802....

  • Page 31

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 26 event description: conflict lldp-med device type detected log message: conflict lldp-med device type detected ( on port >, chassis id: , , port id: , , device class: ) parameters description: portnum: the port number. Chassistype: chassis...

  • Page 32

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 27 bgp event description: bgp fsm with peer has gone to the successfully established state. Log message: [bgp(1):] bgp connection is successfully established (peer:). Parameters description: ipaddr: ip address of bgp peer. Informational even...

  • Page 33

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 28 event description: the number of bgp prefix received from this neighbor reaches the threshold. Log message: [bgp(8):] the number of prefix received reaches , max (peer ). Parameters description: num: the number of prefix received. Limit: ...

  • Page 34

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 29 event description: one ospf neighbor state changed from loading to full. Log message: ospf nbr on interface changed state from loading to full parameters description: intf-name: name of ospf interface. Nbr-id: neighbor's router id. Notice...

  • Page 35

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 30 event description: one virtual router state becomes init. Log message: vr at interface switch to init parameters description: vr-id: vrrp virtual router id. Intf-name: interface name on which virtual router is based. Informational event d...

  • Page 36

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 31 event description: a virtual mac address is adding into switch l3 table. Log message: added a virtual ip mac into l3 table parameters description: vrrp-ip-addr: vrrp virtual ip address vrrp-mac-addr: vrrp virtual mac address notice event ...

  • Page 37

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 32 event description: failed when adding a virtual mac into switch l3 table. The box where the mac is learned from is invalid. Log message: failed to add virtual ip mac into l3 table. Box id is invalid parameters description: vrrp-ip-addr: v...

  • Page 38

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 33 port security event description: address full on a port log message: port security violation (mac address: on ) parameters description: macaddr: the violation mac address. Interface-id: the interface name. Warning ssh event description: s...

  • Page 40

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 35 event description: broadcast storm cleared. Log message: broadcast storm has cleared. Parameters description: interface-id: the interface name. Informational event description: multicast storm occurrence. Log message: multicast storm is o...

  • Page 41

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 36 event description: spanning tree port status changed log message: spanning tree port status changed [( [instance: ], port:)] -> parameters description: instanceid: instance id. Portnum: port id old_status: old status new_status: new statu...

  • Page 42

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 37 port event description: port linkup log message: port link up, parameters description: port: represents the logical port number. Nway: represents the speed and duplex of link. Informational event description: port linkdown log message: po...

  • Page 43

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 38 event description: temperature sensor enters alarm state. Log message: [uint ] temperature sensor enters alarm state (current temperature: ) parameters description: unitid: the unit id. Sensorid: the sensor id. Temperature: the temperatur...

  • Page 44: Appendix C - Trap Entries

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 39 appendix c - trap entries this table lists the trap logs found on the switch. Category trap name description oid up/download agentfirmwareupgrade this trap is sent when the process of upgrading the firmware via snmp has finished. Binding ...

  • Page 45

    Dxs-3600-32s 10gbe layer 2/3 switch web ui reference guide 40 start trap coldstart a coldstart trap signifies that the snmpv2 entity, acting in an agent role, is reinitializing itself and that its configuration may have been altered. 1.3.6.1.6.3.1.1.5.1 warmstart a warmstart trap signifies that the ...