1. DL manuals
  2. D-Link
  3. Switch
  4. xStack DES-3200 Series
  5. Reference Manual

D-Link xStack DES-3200 Series Reference Manual

Other manuals for xStack DES-3200 Series: Reference manual, Installation Manual, Reference Manual, Reference Manual

Summary of xStack DES-3200 Series

  • Page 2: Table Of Contents

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide i table of contents chapter 1 using command line interface ............................................................................................. 1 chapter 2 basic command list .....................................

  • Page 3

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide ii chapter 35 layer 2 protocol tunneling (l2pt) command list ........................................................... 334 chapter 36 link aggregation command list .......................................................

  • Page 4

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide iii chapter 71 trace route command list .............................................................................................. 602 chapter 72 traffic control command list ..........................................

  • Page 5: Chapter 1

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 1 chapter 1 using command line interface the switch can be managed through the switch’s serial port, telnet, snmp or the web-based management agent. The command line interface (cli) can be used to configure and manage ...

  • Page 6

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 2 the switch is also assigned a unique mac address by the factory. This mac address cannot be changed, and can be found on the initial boot console screen – shown below. Boot procedure v4.00.001 -----------------------...

  • Page 7

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 3 there are a number of helpful features included in the cli. Entering the ? Command will display a list of all of the top-level commands. .. ? Cable_diag ports cd cfm linktrace cfm loopback clear clear address_binding...

  • Page 8

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 4 des-3200-28p:admin#config account command: config account next possible completions: des-3200-28p:admin#config account in the above example, the command config account was entered without the required parameter , the...

  • Page 9

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 5 des-3200-28p:admin#show command: show next possible completions: 802.1p 802.1x access_profile account accounting acct_client address_binding arp_spoofing_prevention arpentry attack_log auth_client auth_diagnostics au...

  • Page 11

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 7 insert toggle on and off. When toggled on, inserts text and shifts previous text to right. Left arrow move cursor to left. Right arrow move cursor to right tab help user to select appropriate token. P display the pre...

  • Page 13

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 9 id live time from level name --- ------------ --------------------------------------- ----- --------------- 0 00:01:46.360 10.90.90.10 puser puser 8 00:05:49.340 serial port admin admin total entries: 2 ctrl+c esc q ...

  • Page 15

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 11 example to enable pausing of the screen display when show command output reaches the end of the page: des-3200-28p:admin#enable clipaging command: enable clipaging success. Des-3200-28p:admin# 2-5 disable clipaging ...

  • Page 16

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 12 parameters none. Restrictions none. Example to login the switch with a user name dlink: des-3200-28p:admin#login command: login username:dlink password:**** des-3200-28p:admin# 2-7 logout description this command is...

  • Page 17

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 13 des-3200-28p:admin#logout command: logout ********** * logout * ********** des-3200-28p fast ethernet switch command line interface firmware: build 4.03.004 copyright(c) 2012 d-link corporation. All rights reserved....

  • Page 18

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 14 format clear parameters none. Restrictions none. Example to clear screen: des-3200-28p:admin#clear command: clear des-3200-28p:admin# 2-10 show command_history description the command is used to display command hist...

  • Page 19

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 15 des-3200-28p:admin#show command_history command: show command_history ? Ping login show serial_port show session ? Config bpdu_protection ports ? Reset ? Create account ? Create ipif show the ? Des-3200-28p:admin# 2...

  • Page 20

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 16 format config greeting_message {default} parameters default - (optional) adding this parameter to the “config greeting_message” command will return the greeting message (banner) to its original factory default entry...

  • Page 21

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 17 restrictions only administrator and operator-level users can issue this command. Example to display greeting message: des-3200-28p:admin#show greeting_message command: show greeting_message =========================...

  • Page 22

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 18 des-3200-28p:admin#config command_prompt prompt# command: config command_prompt prompt# success. Prompt#:admin# 2-15 config terminal width description the command is used to set current terminal width. The usage is ...

  • Page 23

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 19 format show terminal width parameters none. Restrictions none. Example to display the configuration of current terminal width: des-3200-28p:admin#show terminal width command: show terminal width global terminal widt...

  • Page 24

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 20 without any master or slave setting for other interface. Master - specify that the port(s) will be set to master. Slave - specify that the port(s) will be set to slave. Flow_control - (optional) you can turn on or t...

  • Page 25

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 21 - (optional) enter the list of ports to be configured here. Description - (optional) indicates if port description will be included in the display . Err_disabled - (optional) indicates if ports are disabled by some ...

  • Page 27

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 23 example to create a vlan with name “v2” and vlan id 2: des-3200-28p:admin#create vlan v2 tag 2 type 1q_vlan advertisement command: create vlan v2 tag 2 type 1q_vlan advertisement success. Des-3200-28p:admin# 3-2 cre...

  • Page 28

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 24 format delete vlan parameters vlan - the vlan name of the vlan to be deleted. - enter the vlan name here. This name can be up to 32 characters long. Restrictions only administrator, operator and power-user level use...

  • Page 30

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 26 parameters - enter a list of vlan ids to configure. Add - (optional) specify to add tagged, untagged or forbidden ports to the vlan. Tagged - specify the additional ports as tagged. Untagged - specify the additional...

  • Page 31

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 27 acceptable_frame - (optional) the type of frame will be accepted by the port. There are two types: tagged_only - only tagged packets can be accepted by this port. Admit_all - all packets can be accepted. Pvid - (opt...

  • Page 32

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 28 des-3200-28p:admin#show vlan command: show vlan vlan trunk state : enabled vlan trunk member ports : 1-5 vid : 1 vlan name : default vlan type : static advertisement : enabled member ports : 1-28 static ports : 1-28...

  • Page 33

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 29 des-3200-28p:admin#show vlan ports 6 command: show vlan ports 6 port vid untagged tagged dynamic forbidden ----- ---- -------- ------ ------- --------- 6 1 x - - - 6 2 - x - - des-3200-28p:admin# 3-10 show vlan vlan...

  • Page 34

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 30 3-11 show port_vlan description this command is used to display the ports’ vlan attributes on the switch. Format show port_vlan {} parameters - (optional) specify a range of ports to be displayed. If no parameter sp...

  • Page 35

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 31 3-12 enable pvid auto assign description this command is used to enable the auto-assignment of pvid. If “auto-assign pvid” is enabled, pvid will be possibly changed by pvid or vlan configuration. When user configure...

  • Page 36

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 32 restrictions only administrator, operator and power-user level users can issue this command. Example to disable the auto-assign pvid: des-3200-28p:admin#disable pvid auto_assign command: disable pvid auto_assign suc...

  • Page 38

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 34 restrictions none. Example to display the global setting of gvrp: des-3200-28p:admin#show gvrp command: show gvrp global gvrp : disabled join time : 200 milliseconds leave time : 600 milliseconds leaveall time : 100...

  • Page 39

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 35 format disable gvrp parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable the generic vlan registration protocol (gvrp): des-3200-28p:admin#...

  • Page 41

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 37 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example used to enable the 802.1x function: des-3200-28p:admin#enable 802.1x command: enable 802.1x succe...

  • Page 42

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 38 4-3 create 802.1x user description this command is used to create an 802.1x user. Format create 802.1x user parameters - enter the username to be added. This value can be up to 15 characters long. Restrictions only ...

  • Page 43

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 39 des-3200-28p:admin#delete 802.1x user test command: delete 802.1x user test success. Des-3200-28p:admin# 4-5 show 802.1x user description this command is used to display the 802.1x user. Format show 802.1x user para...

  • Page 44

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 40 parameters local - specify the authentication protocol as local. Radius_eap - specify the authentication protocol as radius eap. Restrictions only administrator, operator and power-user level users can issue this co...

  • Page 45

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 41 des-3200-28p:admin#config 802.1x fwd_pdu system enable command: config 802.1x fwd_pdu system enable success. Des-3200-28p:admin# 4-8 config 802.1x fwd_pdu ports description this command is used to control the forwar...

  • Page 47

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 43 des-3200-28p:admin#show 802.1x auth_configuration ports 1 command: show 802.1x auth_configuration ports 1 port number : 1 capability : none admincrldir : both opencrldir : both port control : auto quietperiod : 60 s...

  • Page 48

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 44 example to configure the port capability: des-3200-28p:admin#config 802.1x capability ports 1-10 authenticator command: config 802.1x capability ports 1-10 authenticator success. Des-3200-28p:admin# 4-12 config 802....

  • Page 50

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 46 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the parameters that control the operation of the authenticator associated with a port: des-3200-28p:a...

  • Page 52

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 48 restrictions only administrator, operator and power-user level users can issue this command. Example to re-authenticate the device connected to the port: des-3200-28p:admin#config 802.1x reauth port_based ports all ...

  • Page 53

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 49 format delete 802.1x guest_vlan {} parameters - (optional) enter the vlan name here. The vlan name can be up to 32 characters long. Restrictions only administrator, operator and power-user level users can issue this...

  • Page 54

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 50 des-3200-28p:admin#config 802.1x guest_vlan ports 2-8 state enable command: config 802.1x guest_vlan ports 2-8 state enable warning, the ports are moved to guest vlan. Success. Des-3200-28p:admin# 4-20 show 802.1x g...

  • Page 56

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 52 parameters - specify to delete a radius server.Enter the radius server index. Restrictions only administrator, operator and power-user level users can issue this command. Example to delete a radius server: des-3200-...

  • Page 57

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 53 retransmit - (optional) the count for re-transmitting. The default value is 2. - enter the re-transmit value here. This value must be between 1 and 20. Default - specify that the default re-transmit value will be us...

  • Page 58

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 54 des-3200-28p:admin#show radius command: show radius index ip address auth-port acct-port timeout retransmit key (sec) ----- --------------- --------- --------- ------- ---------- ---------------- 1 10.48.74.121 60 1...

  • Page 59

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 55 des-3200-28p:admin#show auth_statistics ports 1 command: show auth_statistics ports 1 port number : 1 eapolframesrx 0 eapolframestx 9 eapolstartframesrx 0 eapolreqidframestx 6 eapollogoffframesrx 0 eapolreqframestx ...

  • Page 60

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 56 des-3200-28p:admin#show auth_diagnostics ports 1 command: show auth_diagnostics ports 1 port number : 1 entersconnecting 11 eaplogoffswhileconnecting 0 entersauthenticating 0 successwhileauthenticating 0 timeoutswhi...

  • Page 61

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 57 des-3200-28p:admin#show auth_session_statistics ports 1 command: show auth_session_statistics ports 1 port number : 1 sessionoctetsrx 0 sessionoctetstx 0 sessionframesrx 0 sessionframestx 0 sessionid sessionauthenti...

  • Page 62

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 58 des-3200-28p:admin#show auth_client command: show auth_client radiusauthclient ==> radiusauthclientinvalidserveraddresses 0 radiusauthclientidentifier radiusauthserverentry ==> radiusauthserverindex :1 radiusauthser...

  • Page 63

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 59 des-3200-28p:admin#show acct_client command: show acct_client radiusacctclient ==> radiusacctclientinvalidserveraddresses 0 radiusacctclientidentifier radiusauthserverentry ==> radiusaccserverindex : 1 radiusaccserv...

  • Page 64

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 60 example enable it to configure accounting shell state: des-3200-28p:admin#config accounting service shell state enable command: config accounting service shell state enable success. Des-3200-28p:admin# 4-31 show acc...

  • Page 65: Chapter 5

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 61 chapter 5 access authentication control command list enable password encryption disable password encryption enable authen_policy disable authen_policy show authen_policy create authen_login method_list_name config a...

  • Page 66

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 62 parameters none. Restrictions only administrator-level users can issue this command. Example to enable the password encryption: des-3200-28p:admin#enable password encryption command: enable password encryption succe...

  • Page 67

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 63 5-3 enable authen_policy description this command is used to enable system access authentication policy. Enable system access authentication policy. When authentication is enabled, the device will adopt the login au...

  • Page 68

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 64 restrictions only administrator-level users can issue this command. Example to disable system access authentication policy: des-3200-28p:admin#disable authen_policy command: disable authen_policy success. Des-3200-2...

  • Page 69

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 65 format create authen_login method_list_name parameters - the user-defined method list name. This value can be up to 15 characters long. Restrictions only administrator-level users can issue this command. Example to ...

  • Page 70

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 66 tacacs+ - (optional) authentication by the built-in server group “tacacs+”. Radius - (optional) authentication by the built-in server group “radius”. Server_group - (optional) authentication by the user-defined serv...

  • Page 72

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 68 restrictions only administrator-level users can issue this command. Example to create a user-defined method list for promoting user's privilege to admin level: des-3200-28p:admin#create authen_enable method_list_nam...

  • Page 73

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 69 example to configure a user-defined method list for promoting user's privilege to admin level: des-3200-28p:admin#config authen_enable method_list_name enable_list_1 method tacacs+ tacacs local_enable command: confi...

  • Page 74

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 70 parameters default - display default user-defined method list for promoting user's privilege to admin level. Method_list_name - display the specific user-defined method list for promoting user's privilege to admin l...

  • Page 75

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 71 restrictions only administrator-level users can issue this command. Example to configure the login method list for telnet: des-3200-28p:admin#config authen application telnet login method_list_name login_list_1 comm...

  • Page 76

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 72 5-16 create authen server_group description this command is used to create a user-defined authentication server group. The maximum supported number of server groups including built-in server groups is 8. Each group ...

  • Page 77

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 73 add - add a server host to a server group. Delete - remove a server host from a server group. Server_host - server host’s ip address. - enter the server host ip address here. Protocol - specify the authentication pr...

  • Page 78

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 74 des-3200-28p:admin#delete authen server_group mix_1 command: delete authen server_group mix_1 success. Des-3200-28p:admin# 5-19 show authen server_group description this command is used to display the authentication...

  • Page 82

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 78 des-3200-28p:admin#show authen server_host command: show authen server_host ip address protocol port timeout retransmit key --------------- -------- ----- ------- ---------- ------------------------- 10.1.1.222 taca...

  • Page 83

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 79 parameters - the amount of attempts for user's trying to login or promote the privilege on console or telnet or ssh. This value must be between 1 and 255. Default value is 3. Restrictions only administrator-level us...

  • Page 84

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 80 5-27 enable admin description this command is used to enter the administrator level privilege. Promote the "user" privilege level to "admin" level. When the user enters this command, the authentication method tacacs...

  • Page 85

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 81 parameters encrypt - (optional) specify the password form. Plain_text - specify the password in plain text form. Sha_1 - specify the password in sha-1 encrypted form. - (optional) the password for promoting the priv...

  • Page 89

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 85 - enter the offset chunk 1 value here. This value must be between 0 and 31. - enter the offset chunk 1 mask here. Offset_chunk_2 - (optional) specify that the offset chunk 2 will be used. - enter the offset chunk 2 ...

  • Page 90

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 86 des-3200-28p:admin#create access_profile profile_id 1 profile_name t1 ethernet vlan source_mac 00-00-00-00-00-01 destination_mac 00-00-00-00-00-02 802.1p ethernet_type command: create access_profile profile_id 1 pro...

  • Page 91

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 87 des-3200-28p:admin#delete access_profile profile_id 1 command: delete access_profile profile_id 1 success. Des-3200-28p:admin# 6-3 config access_profile description this command is used to configure an access list e...

  • Page 92

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 88 auto_assign - specify that the access id will automatically be assigned. - enter the access id used here. This value must be between 1 and 256. Ethernet - specify to configure the ethernet access profile. Vlan - (op...

  • Page 93

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 89 mask - (optional) specify an additional mask parameter that can be configured. - enter the destination port mask here. Flag - (optional) specify the tcp flag fields. All - specify that all the tcp flags will be used...

  • Page 94

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 90 - enter the tcp source port mask value here. Dst_port - (optional) specify the value of the ipv6 layer 4 tcp destination port. - enter the tcp destination port value here. This value must be between 0 and 65535. Mas...

  • Page 95

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 91 delete - specify that a profile or a rule will be deleted. Access_id - specify the index of the access list entry. The value range is 1-256, but the supported maximum number of entries depends on the project. - ente...

  • Page 96

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 92 total used hw entries : 128 total available hw entries : 896 ============================================================================== profile id: 1 profile name: etheracl type: ethernet mask on vlan : 0xfff 80...

  • Page 97

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 93 available hw entries : 255 ------------------------------------------------------------------------------ rule id : 1 ports: 3 match on class : 0 action: permit ======================================================...

  • Page 98

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 94 - rule id : 22 ports: 1-7 match on vlan id : 8 mask : 0xfff source mac : 00-01-02-03-04-05 mask : ff-ff-ff-ff-ff-ff destination mac :00-05-04-03-02-00 mask : ff-ff-ff-ff-ff-00 action: deny des-3200-28p:admin# the fo...

  • Page 99

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 95 for single rate three color mode, users need to specify the committed rate, in kbps, the committed burst size, and the excess burst size. For the two rate three color mode, users need to specify the committed rate i...

  • Page 100

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 96 cir - specify the committed information rate. The unit is in kbps. Cir should always be equal or less than pir. - enter the commited information rate value here. This value must be between 1 and 1048576. Cbs - (opti...

  • Page 101

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 97 example to configure a “two rate, three color” flow meter: des-3200-28p:admin#config flow_meter profile_id 1 access_id 1 tr_tcm cir 1000 cbs 2000 pir 2000 pbs 2000 color_blind conform permit counter enable exceed pe...

  • Page 102

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 98 des-3200-28p:admin#show flow_meter command: show flow_meter flow meter information ------------------------------------------------------------------------------ profile id:1 aceess id:1 mode : trtcm / colorblind ci...

  • Page 103

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 99 example to configure a time range named “1” that starts every monday at 01:01:01am and ends at 02:02:02am: des-3200-28p:admin#config time_range 1 hours start_time 1:1:1 end_time 2:2:2 weekdays mon command: config ti...

  • Page 104

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 100 des-3200-28p:admin#show time_range command: show time_range time range information ----------------------------- range name : 1 weekdays : mon start time : 01:01:01 end time : 02:01:01 total entries :1 des-3200-28p...

  • Page 105

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 101 des-3200-28p:admin#show current_config access_profile command: show current_config access_profile #------------------------------------------------------------------- # acl create access_profile ethernet vlan profi...

  • Page 108

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 104 des-3200-28p:admin#config arpentry 10.48.74.121 00-50-ba-00-07-37 command: config arpentry 10.48.74.121 00-50-ba-00-07-37 success. Des-3200-28p:admin# 7-4 config arp_aging time description this command is used to s...

  • Page 109

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 105 restrictions only administrator, operator and power-user level users can issue this command. Example to clear the arp table: des-3200-28p:admin#clear arptable command: clear arptable success. Des-3200-28p:admin# 7-...

  • Page 110

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 106 des-3200-28p:admin#show arpentry command: show arpentry arp aging time : 20 interface ip address mac address type ------------- --------------- ----------------- --------------- system 10.0.0.0 ff-ff-ff-ff-ff-ff lo...

  • Page 112

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 108 des-3200-28p:admin#config arp_spoofing_prevention add gateway_ip 10.254.254.251 gateway_mac 00-00-00-11-11-11 ports 1-2 command: config arp_spoofing_prevention add gateway_ip 10.254.254.251 gateway_ma c 00-00-00-11...

  • Page 113: Chapter 9

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 109 chapter 9 auto-configuration command list enable autoconfig disable autoconfig show autoconfig config autoconfig timeout 9-1 enable autoconfig description this command is used to enable auto configuration. When ena...

  • Page 114

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 110 format disable autoconfig parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable autoconfig: des-3200-28p:admin#disable autoconfig command: disable auto...

  • Page 115

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 111 9-4 config autoconfig timeout description this command is used to configure the timeout value. This timer is used to limit the length of time in getting configuration settings from the network. When timeout occurs,...

  • Page 117

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 113 sha_1 - select to specify the password in the sha-i encrypted form. - the password for the user account. The length for of password in plain-text form and in encrypted form are different. For the plain-text form, p...

  • Page 118

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 114 parameters - enter the user name of the account that has been defined. Encrypt - (optional) specify that the password will be encrypted. Plain_text - select to specify the password in plain text form. Sha_1 - selec...

  • Page 119

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 115 restrictions only administrator-level users can issue this command. Example to display the accounts that have been created: des-3200-28p:admin#show account command: show account current accounts: username access le...

  • Page 120

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 116 10-5 show switch description this command is used to display the switch information. Format show switch parameters none. Restrictions none. Example the following is an example for display of the switch information....

  • Page 121

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 117 10-6 enable telnet description this command is used to enable telnet and configure port number. Format enable telnet {} parameters - (optional) the tcp port number. Tcp ports are numbered between 1 and 65535. The “...

  • Page 122

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 118 des-3200-28p:admin#disable telnet command: disable telnet success. Des-3200-28p:admin# 10-8 enable web description this command is used to enable http and configure port number. Format enable web {} parameters - (o...

  • Page 123

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 119 restrictions only administrator and operator-level users can issue this command. Example to disable http: des-3200-28p:admin#disable web command: disable web success. Des-3200-28p:admin# 10-10 reboot description th...

  • Page 125

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 121 restrictions only administrator level can issue this command. Example to configure c:/des3200_run_4_00_014.Had as the boot up image: des-3200-28p:admin#config firmware image c:/des3200_run_4_02_004.Had boot_up comm...

  • Page 127

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 123 restrictions only administrator, operator and power-user level users can issue this command. Example to configure an interface’s ipv4 network address: des-3200-28p:admin#config ipif system ipaddress 192.168.69.123/...

  • Page 129

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 125 example to disable an ip interface: des-3200-28p:admin#disable ipif newone command: disable ipif newone success. Des-3200-28p:admin# 10-18 show ipif description this command is used to display an ip interface. Form...

  • Page 130

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 126 10-19 enable ipif_ipv6_link_local_auto description this command is used to enable the auto configuration of link local address when there are no ipv6 addresses explicitly configured. When an ipv6 address is explici...

  • Page 131

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 127 restrictions only administrator, operator and power-user level users can issue this command. Example to disable the ip interface for ipv6 link local automatic: des-3200-28p:admin#disable ipif_ipv6_link_local_auto n...

  • Page 133

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 129 example to set the port state enable and drop mode: des-3200-28p:admin#config bpdu_protection ports 1 state enable mode drop commands: config bpdu_protection ports 1 state enable mode drop success. Des-3200-28p:adm...

  • Page 135

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 131 des-3200-28p:admin#enable bpdu_protection commands: enable bpdu_protection success. Des-3200-28p:admin# 11-5 disable bpdu_protection description this command is used to disable bpdu protection function globally for...

  • Page 136

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 132 restrictions none. Example to show the bpdu_protection for the entire switch: des-3200-28p:admin#show bpdu_protection commands: show bpdu_protection bpdu protection global settings ---------------------------------...

  • Page 138

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 134 • when the link partner is powered down with errors , this command can detect whether the error is open, short, or crosstalk. In this case this command can also detect the distance of the error • when there is no l...

  • Page 139

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 135 example test the cable on port 1, 11, and 12: des-3200-28p:admin#cable_diag ports 1,11-12 command: cable_diag ports 1,11-12 perform cable diagnostics ... Port type link status test result cable length (m) ------ --...

  • Page 140: Chapter 13

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 136 chapter 13 command logging command list enable command logging disable command logging show command logging 13-1 enable command logging description this command is used to enable the command logging function. This ...

  • Page 141

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 137 parameters none. Restrictions only administrator-level users can issue this command. Example to disable the command logging: des-3200-28p:admin#disable command logging command: disable command logging success. Des-...

  • Page 143

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 139 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example this example sets authorization global state disabled: des-3200-28p:admin#disable authorization ...

  • Page 145

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 141 des-3200-28p:admin#show authentication command: show authentication authentication server failover: local. Des-3200-28p:admin#.

  • Page 147

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 143 setting regarding stp is not displayed. The lower level setting will only be displayed when the higher level setting is enabled. Note: this parameter is only for the current configuration. Modified - show only the ...

  • Page 148

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 144 des-3200-28p:admin#show config modified command: show config modified #------------------------------------------------------------------------------- # des-3200-28p fast ethernet switch # configuration # # firmwar...

  • Page 149

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 145 example to configure the switch’s configuration file as boot up: des-3200-28p:admin#config configuration config.Cfg boot_up command: config configuration config.Cfg boot_up success. Des-3200-28p:admin# 15-3 save de...

  • Page 150

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 146 parameters none. Restrictions none. Example to display the boot file: des-3200-28p:admin#show boot_file command: show boot_file bootup firmware : /c:/runtime.Had bootup configuration : /c:/config.Cfg des-3200-28p:a...

  • Page 153

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 149 parameters - enter the maintenance domain name. This name can be up to 22 characters long. Md_index - specify the maintenance domain index. - enter the maintenance domain index value here. This value must be betwee...

  • Page 154

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 150 md - specify the maintenance domain name. - enter the maintenance domain name here. This name can be up to 22 characters long. Md_index - specify the maintenance domain index. - enter the maintenance domain index v...

  • Page 155

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 151 vlans. - enter the vlan id used here. This value must be between 1 and 4094. Mip - (optional) this is the control creation of mips. None - specify not to create mips. Auto - mips can always be created on any ports ...

  • Page 157

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 153 • some remote meps down: priority 3 • some remote mep mac status errors: priority 2 • some remote mep defect indications: priority 1 if multiple types of the fault occur on an mep, only the fault with the highest p...

  • Page 158

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 154 alarm_reset_time - (optional) this is the dormant duration time before a defect is triggered before the fault can be re-alarmed. The unit is centisecond, the range is 250-1000. The default value is 1000. - enter th...

  • Page 159

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 155 example to delete a cfm mep: des-3200-28p:admin#delete cfm mep mepname mep1 command: delete cfm mep mepname mep1 success. Des-3200-28p:admin# 16-8 delete cfm ma description this command is used to delete a created ...

  • Page 160

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 156 16-9 delete cfm md description this command is used to delete a previously created maintenance domain. All the meps and maintenance associations created in the maintenance domain will be deleted automatically. Form...

  • Page 161

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 157 example to enable the cfm globally: des-3200-28p:admin#enable cfm command: enable cfm success. Des-3200-28p:admin# 16-11 disable cfm description this command is used to disable the cfm globally. Format disable cfm ...

  • Page 163

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 159 des-3200-28p:admin#show cfm ports 3-6 command: show cfm ports 3-6 port state ----- -------- 3 enabled 4 enabled 5 enabled 6 disabled des-3200-28p:admin# 16-14 show cfm description this command is used to show the c...

  • Page 164

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 160 cfm state: enabled md index md name level ---------- ---------------------- ----- 1 op_domain 2 des-3200-28p:admin#show cfm md op_domain command: show cfm md op_domain md index : 1 md name : op_domain md level : 2 ...

  • Page 165

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 161 cross-connect ccms : 0 received error ccms : 0 received normal ccms : 0 received port status ccms : 0 received if status ccms : 0 received ccms transmitted : 0 in-order lbrs : 0 received out-of-order lbrs : 0 recei...

  • Page 166

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 162 example to show the cfm faults: des-3200-28p:admin#show cfm fault command: show cfm fault md name ma name mepid status ----------- ----------- ----- --------------------------------- op_domain op1 1 cross-connect c...

  • Page 167

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 163 16-17 cfm loopback description this command is used to start a cfm loopback test. You can press ctrl+c to exit the loopback test. The mac address represents the destination mep or mip that can be reached by this ma...

  • Page 168

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 164 des-3200-28p:admin#cfm loopback 32-00-70-89-31-06 mepname mep1 command: cfm loopback 32-00-70-89-31-06 mepname mep1 reply from 32-00-70-89-31-06: bytes=0 time=50ms reply from 32-00-70-89-31-06: bytes=0 time=50ms re...

  • Page 169

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 165 example to transmit an ltm: des-3200-28p:admin#cfm linktrace 00-01-02-03-04-05 mepname mep1 command: cfm linktrace 00-01-02-03-04-05 mepname mep1 transaction id: 26 success. Des-3200-28p:admin# 16-19 show cfm linkt...

  • Page 170

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 166 des-3200-28p:admin#show cfm linktrace mepname mep1 trans_id 26 command: show cfm linktrace mepname mep1 trans_id 26 transaction id: 26 from mep mep1 to 32-00-70-89-31-06 start time : 2011-11-22 16:05:08 hop mepid i...

  • Page 171

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 167 be between 1 and 4294967295. Ma - (optional) specify the maintenance association name. - enter the maintenance association name her. This name can be up to 22 characters long. Ma_index - specify the maintenance ass...

  • Page 172

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 168 des-3200-28p:admin#show cfm mipccm command: show cfm mipccm ma vid mac address port ---------- ---- ----------------- ----- opma 1 xx-xx-xx-xx-xx-xx 2 opma 1 xx-xx-xx-xx-xx-xx 3 total: 2 des-3200-28p:admin# 16-22 c...

  • Page 173

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 169 parameters none. Restrictions none. Example to show the configuration of the "all mps reply ltrs" function: des-3200-28p:admin#show cfm mp_ltr_all command: show cfm mp_ltr_all all mps reply ltrs: disabled des-3200-...

  • Page 174

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 170 example to show the cfm remote mep information: des-3200-28p:admin#show cfm remote_mep mepname mep1 remote_mepid 2 command: show cfm remote_mep mepname mep1 remote_mepid 2 remote mepid : 2 mac address : 00-11-22-33...

  • Page 175

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 171 ----------------------------------------------------------------------------- port allpkt ccm lbr lbm ltr ltm viddrop opcodrop ----- -------- -------- -------- -------- -------- -------- -------- -------- all 2446 ...

  • Page 176

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 172 15 0 0 0 0 0 0 16 0 0 0 0 0 0 17 0 0 0 0 0 0 18 0 0 0 0 0 0 19 0 0 0 0 0 0 20 0 0 0 0 0 0 21 0 0 0 0 0 0 22 0 0 0 0 0 0 23 0 0 0 0 0 0 24 0 0 0 0 0 0 25 0 0 0 0 0 0 26 0 0 0 0 0 0 27 0 0 0 0 0 0 28 0 0 0 0 0 0 des-...

  • Page 177

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 173 restrictions only administrator, operator and power-user level users can issue this command. Example to clear the cfm packet’s rx/tx counters: des-3200-28p:admin#clear cfm pkt_cnt command: clear cfm pkt_cnt success...

  • Page 180

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 176 and 15. - enter the mask pattern offset of the frame between 0 and 15 here. Offset_16-31 - (optional) specify that the mask pattern offset of the frame will be between 16 and 31. - enter the mask pattern offset of ...

  • Page 181

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 177 parameters profile_id - specify the index of access list profile. - enter the profile id value here. This value must be between 1 and 5. All – specify that al the access list profiles will be deleted. Restrictions ...

  • Page 182

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 178 - enter the access id here. This value must be between 1 and 100. Ethernet - specify that the profile type will be ethernet. Vlan - (optional) specify the vlan name used. - enter the name of the vlan here. This nam...

  • Page 183

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 179 and 65535. Protocol_id - specify that the rule applies to the value of ip protocol id traffic. - enter the protocol id value here. This value must be between 0 and 255. User_define - (optional) specify that the rul...

  • Page 184

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 180 des-3200-28p:admin#config cpu access_profile profile_id 1 add access_id 1 ip vlan default source_ip 20.2.2.3 destination_ip 10.1.1.252 dscp 3 icmp type 11 code 32 port 1 deny command: config cpu access_profile prof...

  • Page 185

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 181 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable cpu_interface_filtering: des-3200-28p:admin#disable cpu_interface_filtering command: disable cpu_...

  • Page 186

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 182 profile id: 1 type: ethernet mask on vlan : 0xfff source mac : 00-00-00-00-00-01 destination mac : 00-00-00-00-00-02 802.1p ethernet type unused rule entries: 100 ===================================================...

  • Page 188

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 184 des-3200-28p:admin#debug error_log dump command: debug error_log dump ************************************************************************** # debug log: 1 # level: fatal # clock: 10000ms # time : 2009/03/11 13...

  • Page 190

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 186 18-3 debug output description this command is used to set a specified module’s debug message output to debug buffer or local console. If the user uses the command in a telnet session, the error message also is outp...

  • Page 191

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 187 restrictions only administrator-level users can issue this command. Example to set the switch to not need a reboot when a fatal error occurs: des-3200-28p:admin#debug config error_reboot disable command: debug conf...

  • Page 192

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 188 format debug show error_reboot state parameters none. Restrictions only administrator-level users can issue this command. Example to show the debug error reboot state: des-3200-28p:admin#debug show error_reboot sta...

  • Page 193

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 189 des-3200-28p:admin#debug show status module mstp command: debug show status module mstp debug global state : enabled mstp : disabled des-3200-28p:admin# to show the debug state: des-3200-28p:admin#debug show status...

  • Page 196

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 192 example to configure the circuit id of dhcp relay agent as default: des-3200-28p:admin#config dhcp_local_relay option_82 circuit_id default command: config dhcp_local_relay option_82 circuit_id default success. Des...

  • Page 197

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 193 parameters default - use the switch’s system mac address as the remote id. User_define - use user-defined string as the remote id. - enter the maximum of 32 characters. Space is allowed in the string. Restrictions ...

  • Page 198

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 194 19-7 disable dhcp_local_relay description this command is used to globally disable the dhcp local relay function on the switch. Format disable dhcp_local_relay parameters none. Restrictions only administrator, oper...

  • Page 199

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 195 des-3200-28p:admin#show dhcp_local_relay command: show dhcp_local_relay dhcp/bootp local relay status : disabled dhcp/bootp local relay vid list : 1 dhcp relay agent information option 82 circuit id : default dhcp ...

  • Page 201

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 197 example to configure the dhcp relay hops and time parameters: des-3200-28p:admin#config dhcp_relay hops 4 time 2 command: config dhcp_relay hops 4 time 2 success. Des-3200-28p:admin# 20-2 config dhcp_relay add desc...

  • Page 202

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 198 format config dhcp_relay add vlanid parameters vlanid - specify the vlan id list used for this configuration. - enter the vlan id list used for this configuration here. - enter the dhcp/bootp server ip address used...

  • Page 203

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 199 20-4 config dhcp_relay delete description this command is used to delete one of the ip destination addresses in the switch’s relay table. Format config dhcp_relay delete ipif parameters ipif - the name of the ip in...

  • Page 204

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 200 example to delete a dhcp/bootp server 10.43.21.12 from vlan 2 and vlan 3: des-3200-28p:admin#config dhcp_relay delete vlanid 2-3 10.43.21.12 command: config dhcp_relay delete vlanid 2-3 10.43.21.12 success. Des-320...

  • Page 205

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 201 restrictions only administrator, operator and power-user level users can issue this command. Example to configure dhcp_relay option 82: des-3200-28p:admin#config dhcp_relay option_82 state enable command: config dh...

  • Page 206

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 202 example to configure the circuit id as default: des-3200-28p:admin#config dhcp_relay option_82 circuit_id default command: config dhcp_relay option_82 circuit_id default success. Des-3200-28p:admin# 20-8 enable dhc...

  • Page 207

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 203 restrictions only administrator, operator and power-user level users can issue this command. Example to disable the dhcp relay function: des-3200-28p:admin#disable dhcp_relay command: disable dhcp_relay success. De...

  • Page 208

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 204 des-3200-28p:admin#show dhcp_relay ipif system command: show dhcp_relay ipif system dhcp/bootp relay status : enabled dhcp/bootp hops count limit : 4 dhcp/bootp relay time threshold : 2 dhcp vendor class identifier...

  • Page 209

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 205 example to configure the state of dhcp_relay option 60: des-3200-28p:admin#config dhcp_relay option_60 state enable command: config dhcp_relay option_60 state enable success des-3200-28p:admin# 20-12 config dhcp_re...

  • Page 210

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 206 20-13 config dhcp_relay option_60 default description this command is used to configure the dhcp relay option 60 default drop option. When there are no match servers found for the packet based on option 60, the rel...

  • Page 212

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 208 restrictions none. Example to show dhcp option 60 information: des-3200-28p:admin#show dhcp_relay option_60 command: show dhcp_relay option_60 default processing mode: drop default servers: matching rules: string m...

  • Page 213

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 209 example to configure the state of dhcp_relay option 61: des-3200-28p:admin#config dhcp_relay option_61 state enable command: config dhcp_relay option_61 state enable success des-3200-28p:admin# 20-17 config dhcp_re...

  • Page 215

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 211 restrictions only administrator, operator and power-user level users can issue this command. Example to remove a dhcp relay option 61 entry: des-3200-28p:admin#config dhcp_relay option_61 delete mac_address 00-11-2...

  • Page 216

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 212 des-3200-28p:admin#show dhcp_relay option_61 command: show dhcp_relay option_61 default relay rule:drop matching rules: client-id type relay rule ----------- ---- --------- 00-11-22-33-44-55 mac address drop total ...

  • Page 218

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 214 state - specify the state of the dhcp server filtering. Enable - enable the dhcp server filtering. Disable - disable the dhcp server filtering. Illegal_server_log_suppress_duration - specify the same illegal dhcp s...

  • Page 219

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 215 example to display the dhcp server/client filter list created on the switch: des-3200-28p:admin#show filter dhcp_server command: show filter dhcp_server enabled ports: 1-10 trap & log state: disabled illegal server...

  • Page 221

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 217 des-3200-28p:admin#config ddm trap enable command: config ddm trap enable success. Des-3200-28p:admin# 22-2 config ddm ports description the command is used to configure the ddm settings of the specified ports. For...

  • Page 222

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 218 example to configure the port 25’s temperature threshold: des-3200-28p:admin#config ddm ports 25 temperature_threshold high_alarm 84.9532 low_alarm -10 high_warning 70 low_warning 2.25 command: config ddm ports 25 ...

  • Page 223

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 219 des-3200-28p:admin#config ddm ports 25 rx_power_threshold high_alarm 4.55 low_alarm 0.01 high_warning 3.5 low_warning 0.03 command: config ddm ports 25 rx_power_threshold high_alarm 4.55 low_alarm 0.01 high_warning...

  • Page 224

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 220 22-4 show ddm ports description this command is used to show the current operating ddm parameters and configuration values of the optic module of the specified ports. There are two types of thresholds: the administ...

  • Page 225

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 221 des-3200-28p:admin#show ddm ports 25-26 status command: show ddm ports 25-26 status port temperature voltage bias current tx power rx power (in celsius) (v) (ma) (mw) (mw) ------- ------------- ---------- ---------...

  • Page 227

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 223 des-3200-28p:admin#config duld ports 1 state enable command: config duld ports 1 state enable success. Des-3200-28p:admin# 23-2 show duld ports description this command is used to show unidirectional link detection...

  • Page 229

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 225 example to configure land attack and blat attack prevention, the action is drop: des-3200-28p:admin#config dos_prevention dos_type land_attack blat_attack action drop state enable command: config dos_prevention dos...

  • Page 230

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 226 des-3200-28p:admin#show dos_prevention command: show dos_prevention trap:disabled log:disabled function version : 1.01 dos type state action frame counts -------------------------- -------- ---------------- -------...

  • Page 233

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 229 des-3200-28p:admin#enable erps command: enable erps success. Des-3200-28p:admin# 25-2 disable erps description this command is used to disable the global erps function on a switch. Format disable erps parameters no...

  • Page 234

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 230 - enter the vlan id used here. Restrictions only administrator, operator and power-user level users can issue this command. Example to create an r-aps vlan: des-3200-28p:admin#create erps raps_vlan 4094 command: cr...

  • Page 235

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 231 25-5 config erps raps_vlan description this command is used to configure the erps r-aps vlan settings. The ring mel is one field in the r-aps pdu. Note that if cfm (connectivity fault management) and erps are used ...

  • Page 236

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 232 unblocked rpl port and start to send r-aps pdu with an rb flag after the link recovery is confirmed within this period of time. Revertive mode - when revertive is enabled, the traffic link is restored to the workin...

  • Page 237

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 233 disable - specify that the r-aps revertive option will be disabled. Timer - specify the r-aps timer used. Holdoff_time - (optional) specify the holdoff time of the r-aps function. The default holdoff time is 0 mill...

  • Page 238

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 234 des-3200-28p:admin#config erps raps_vlan 4094 protected_vlan add vlanid 10-20 command: config erps raps_vlan 4094 protected_vlan add vlanid 10-20 success. Des-3200-28p:admin# to configure the erps timers for a spec...

  • Page 239

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 235 des-3200-28p:admin#config erps log enable command: config erps log enable success. Des-3200-28p:admin# 25-7 config erps trap description this command is used to configure trap state of erps events. Format config er...

  • Page 240

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 236 format show erps parameters none. Restrictions none. Example to display erps information: des-3200-28p:admin#show erps command: show erps global status : disabled log status : disabled trap status : disabled ------...

  • Page 242

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 238 parameters none. Restrictions none. Example to display the filter netbios list created on the switch: des-3200-28p:admin#show filter netbios command: show filter netbios enabled ports: 1-3 des-3200-28p:admin# 26-3 ...

  • Page 243

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 239 26-4 show filter extensive_netbios description this command is used to display the extensive netbios state on the switch. Format show filter extensive_netbios parameters none. Restrictions none. Example to display ...

  • Page 245

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 241 des-3200-28p:admin#create fdb default 00-00-00-00-01-02 port 5 command: create fdb default 00-00-00-00-01-02 port 5 success. Des-3200-28p:admin# to filter a unicast mac: des-3200-28p:admin#create fdb default 00-00-...

  • Page 246

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 242 des-3200-28p:admin#create fdb vlanid 1 00-00-00-00-02-02 drop command: create fdb vlanid 1 00-00-00-00-02-02 drop success. Des-3200-28p:admin# 27-3 create multicast_fdb description this command is used to create a ...

  • Page 247

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 243 name length is 32. - the mac address that will be added or deleted to the forwarding table. Add - specify to add ports to the multicast forwarding table. Delete - specify to remove ports from the multicast forwardi...

  • Page 248

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 244 des-3200-28p:admin#config fdb aging_time 600 command: config fdb aging_time 600 success. Des-3200-28p:admin# 27-6 config multicast vlan_filtering_mode description this command is used to configure the multicast pac...

  • Page 249

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 245 27-7 delete fdb description this command is used to delete a static entry from the forwarding database. Format delete fdb parameters - the name of the vlan on which the mac address resides. The maximum name length ...

  • Page 250

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 246 restrictions only administrator, operator and power-user level users can issue this command. Example to clear all fdb dynamic entries: des-3200-28p:admin#clear fdb all command: clear fdb all success. Des-3200-28p:a...

  • Page 251

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 247 des-3200-28p:admin#show multicast_fdb command: show multicast_fdb vlan name : default mac address : 01-00-5e-00-00-00 egress ports : 1-5 mode : static total entries: 1 des-3200-28p:admin# 27-10 show fdb description...

  • Page 252

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 248 des-3200-28p:admin#show fdb command: show fdb unicast mac address aging time = 300 vid vlan name mac address port type status ---- -------------------------------- ----------------- ----- ------- ------- 1 default ...

  • Page 253

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 249 long. If no parameter is specified, the device will show all multicast filtering settings in the device. Restrictions none. Example to show the multicast vlan_filtering_mode for vlans: des-3200-28p:admin#show multi...

  • Page 254: Chapter 28

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 250 chapter 28 flash file system (ffs) command list show storage_media_info md {} rd {} cd {} dir {} {} rename {} del {} {recursive} erase {} move {} {} copy {} {} 28-1 show storage_media_info description this command ...

  • Page 255

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 251 28-2 md description this command is used to create a directory. Format md {} parameters - (optional) enter the drive id used, for example, c:. - specify the directory to be removed. The path name can be specified e...

  • Page 256

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 252 example to remove a directory: des-3200-28p:admin#rd c:/abc command: rd c:/abc success. Des-3200-28p:admin# 28-4 cd description this command is used to change the current directory. The current directory is changed...

  • Page 257

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 253 format dir {} {} parameters - (optional) enter the drive id used, for example, c:. - (optional) specify the directory to be removed. The path name can be specified either as a full path name or partial name. For pa...

  • Page 258

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 254 parameters - (optional) enter the drive id used, for example, c:. - specify the file (in path form) to be renamed. - specify the new name of the file. Restrictions only administrator and operator-level users can is...

  • Page 259

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 255 des-3200-28p:admin#dir command: dir directory of / c: idx info attr size update time name --- ------- ---- -------- ------------------- ---------------- 1 drw- 0 2000/04/02 06:02:04 12 2 cfg(*) -rw- 29661 2000/04/0...

  • Page 260

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 256 related to the current directory. Restrictions only administrator and operator-level users can issue this command. Example to erase a file: des-3200-28p:admin#dir command: dir directory of /c: idx info attr size up...

  • Page 261

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 257 format move {} {} parameters - (optional) enter the drive id, for example, c:. - specify the file to be moved. The path name can be specified either as a full path name or partial name. Specify either as a full pat...

  • Page 262

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 258 example to copy a file: des-3200-28p:admin#copy c:/log.Txt c:/log1.Txt command: copy c:/log.Txt c:/log1.Txt success. Des-3200-28p:admin#.

  • Page 264

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 260 that the system received a arp request packet that is sent by an ip address that match the system’s own ip address. In this case, the system knows that some body out there uses an ip address that is conflict with t...

  • Page 265

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 261 restrictions only administrator, operator and power-user level users can issue this command. Example to show the global gratuitousarp state: des-3200-28p:admin#config gratuitous_arp learning enable command: config ...

  • Page 266

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 262 29-5 enable gratuitous_arp description the command is used to enable gratuitous arp trap and log state. The switch can trap and log the ip conflict event to inform the administrator. By default, trap is disabled an...

  • Page 267

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 263 restrictions only administrator, operator and power-user level users can issue this command. Example to disable system interface’s gratuitous arp log and trap: des-3200-28p:admin#disable gratuitous_arp ipif system ...

  • Page 268

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 264 des-3200-28p:admin#show gratuitous_arp command: show gratuitous_arp send on ipif status up : enabled send on duplicate ip detected : enabled gratuitous arp learning : enabled ip interface name : system gratuitous a...

  • Page 269: Chapter 30

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 265 chapter 30 igmp / mld snooping command list the internet group management protocol (igmp) is a l3 protocol used to manage the membership of internet protocol multicast groups. Igmp is used by ip hosts and adjacent ...

  • Page 271

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 267 parameters vlan_name - specify the name of the vlan for which igmp snooping is to be configured. - enter the vlan name here. The vlan name can be up to 32 characters long. Vlanid - specify the vlan id for which igm...

  • Page 272

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 268 - configure the rate of the igmp control packet that the switch can process on a specific port/vlan. The rate is specified in packets per second. The packets that exceed the limit will be dropped. No_limit - config...

  • Page 273

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 269 subnet. The value of the robustness variable is used in calculating the following igmp message intervals: - enter the robustness variable value here. This value must be between 1 and 7. By default, the robustness v...

  • Page 274

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 270 30-4 config igmp access_authentication ports description this command is used to enable or disable the igmp access control function for the specified ports. If the igmp access control function is enabled and the sw...

  • Page 275

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 271 delete - specify to delete the router ports. - specify a range of ports to be configured. Restrictions only administrator, operator and power-user level users can issue this command. Example to set up static router...

  • Page 276

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 272 30-7 enable igmp_snooping description this command is used to enable igmp snooping on the switch. Format enable igmp_snooping parameters none. Restrictions only administrator, operator and power-user level users ca...

  • Page 277

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 273 example to disable igmp snooping on the switch: des-3200-28p:admin#disable igmp_snooping command: disable igmp_snooping success. Des-3200-28p:admin# 30-9 create igmp_snooping static_group description this command i...

  • Page 278

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 274 des-3200-28p:admin#create igmp_snooping static_group vlan default 239.1.1.1 command: create igmp_snooping static_group vlan default 239.1.1.1 success. Des-3200-28p:admin# 30-10 delete igmp_snooping static_group des...

  • Page 280

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 276 restrictions none. Example to display all the igmp snooping static groups: des-3200-28p:admin#show igmp_snooping static_group vlan id/name ip address static member ports -------------- ------------------ ----------...

  • Page 281

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 277 state - (optional) specify to enable or disable the data driven learning of an igmp snooping group. Enable - enter enable to enable the data driven learning option. By default, the state is enabled. Disable - enter...

  • Page 282

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 278 restrictions only administrator, operator and power-user level users can issue this command. Example to set the maximum number of groups that can be learned by data driven: des-3200-28p:admin#config igmp_snooping d...

  • Page 284

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 280 des-3200-28p:admin#show igmp_snooping command: show igmp_snooping igmp snooping global state : enabled data driven learning max entries : 128 vlan name : default query interval : 125 max response time : 10 robustne...

  • Page 285

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 281 example to display the igmp snooping rate limit for ports 1 to 15: des-3200-28p:admin#show igmp_snooping rate_limit ports 1-15 command: show igmp_snooping rate_limit ports 1-15 port rate limit -------- ----------- ...

  • Page 286

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 282 des-3200-28p:admin#show igmp_snooping group command: show igmp_snooping group source/group : 10.0.0.1/225.0.0.1 vlan name/vid : default/1 member ports : 5 up time : 6 expiry time : 254 filter mode : include source/...

  • Page 287

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 283 member ports : 5 up time : 10 expiry time : 258 filter mode : exclude source/group : null/226.0.0.2 vlan name/vid : default/1 member ports : 5 up time : 9 expiry time : 259 filter mode : exclude source/group : null...

  • Page 288

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 284 - enter the vlan id list here. If no parameter is specified, the system will display all current igmp snooping forwarding table entries of the switch. Restrictions none. Example to show all igmp snooping forwarding...

  • Page 289

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 285 all - specify all vlans on which the router port resides. Static - (optional) displays router ports that have been statically configured. Dynamic - (optional) displays router ports that have been dynamically config...

  • Page 290

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 286 - enter the list of port to be displayed here. Restrictions none. Example to display the igmp snooping statistics counter: des-3200-28p:admin#show igmp_snooping statistic counter vlanid 67 command: show igmp_snoopi...

  • Page 291

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 287 des-3200-28p:admin# to display the igmp snooping statistics counter for a port: des-3200-28p:admin#show igmp_snooping statistic counter ports 1 command: show igmp_snooping statistic counter ports 1 port # : 1 -----...

  • Page 293

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 289 12 disabled 13 disabled 14 disabled 15 disabled 16 disabled 17 disabled 18 disabled 19 disabled 20 disabled ctrl+c esc q quit space n next page enter next entry a all 30-23 clear igmp_snooping statistics counter de...

  • Page 294

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 290 parameters vlan_name - specify the name of the vlan for which mld snooping is to be configured. - enter the vlan name here. The vlan name can be up to 32 characters long. Vlanid - specify the id of the vlan for whi...

  • Page 295

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 291 - enter the vlan id list here. All - specify all vlans for which mld snooping querier is to be configured. Query_interval - specify the amount of time in seconds between general query transmissions. The default set...

  • Page 296

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 292 30-26 config mld_snooping router_ports description this command is used to designate a range of ports as being connected to multicast-enabled routers. This will ensure that all packets with such a router as its des...

  • Page 297

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 293 parameters vlan - specify the name of the vlan on which the forbidden router port resides. - enter the vlan name here. The vlan name can be up to 32 characters long. Vlanid - specify the id of the vlan on which the...

  • Page 298

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 294 des-3200-28p:admin#enable mld_snooping command: enable mld_snooping success. Des-3200-28p:admin# 30-29 disable mld_snooping description this command is used to disable mld snooping on the switch. Format disable mld...

  • Page 299

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 295 configuration. - enter the vlan name here. The vlan name can be up to 32 characters long. Vlanid - (optional) specify the id of the vlan for which you want to view the mld snooping configuration. - enter the vlan i...

  • Page 301

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 297 des-3200-28p:admin#show mld_snooping group command: show mld_snooping group source/group : 2001::1/fe1e::1 vlan name/vid : default/1 member ports : 1-2 up time : 26 expiry time : 258 filter mode : include source/gr...

  • Page 302

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 298 30-32 show mld_snooping forwarding description this command is used to display the switch’s current mld snooping forwarding table. It provides an easy way for users to check the list of ports that the multicast gro...

  • Page 304

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 300 the static group will only take effect when mld snooping is enabled on the vlan. An active static group must be equal to a static mld group with a link-up member port. For those static member ports, the device need...

  • Page 305

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 301 - enter the vlan id list here. - specify the multicast group ip address. Restrictions only administrator, operator and power-user level users can issue this command. Example to delete an mld snooping static group f...

  • Page 306

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 302 des-3200-28p:admin#config mld_snooping static_group vlan default ff1e::1 delete 9-10 command: config mld_snooping static_group vlan default ff1e::1 delete 9-10 success. Des-3200-28p:admin# 30-37 show mld_snooping s...

  • Page 307

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 303 snooping entry, the mld protocol will take care the aging out of the entry. For a data-driven entry, the entry can be specified not to be aged out or to be aged out by the aged timer. When the data driven learning ...

  • Page 308

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 304 30-39 config mld_snooping data_driven_learning max_learned_entry description this command is used to configure the maximum number of groups that can be learned by data driven. When the table is full, the system wil...

  • Page 309

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 305 - enter the vlan name here. Vlanid - specify the vlan id. - enter the vlan id list here. - specify the group’s ip address learned by data driven. All - specify to clear all data driven groups of the specified vlan....

  • Page 310

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 306 des-3200-28p:admin# show mld_snooping statistic counter vlanid 1 command: show mld_snooping statistic counter vlanid 1 vlan name : default ----------------------------------------------- total groups : 10 receive s...

  • Page 311

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 307 restrictions only administrator, operator and power-user level users can issue this command. Example to clear mld snooping statistics counter: des-3200-28p:admin#clear mld_snooping statistics counter command: clear...

  • Page 312

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 308 des-3200-28p:admin#config mld_snooping rate_limit ports 1 100 command: config mld_snooping rate_limit ports 1 100 success. Des-3200-28p:admin# 30-44 show mld_snooping rate_limit description this command is used to ...

  • Page 314

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 310 restrictions only administrator, operator and power-user level users can issue this command. Example to create an impb entry: des-3200-28p:admin#create address_binding ip_mac ipaddress 10.1.1.1 mac_address 00-00-00...

  • Page 315

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 311 when set to disabled, the broadcast dhcp packet received by the specified port will not be forwarded. This setting is effective when dhcp snooping is enabled, in this case dhcp packets trapped by the cpu must be fo...

  • Page 316

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 312 des-3200-28p:admin#delete address_binding blocked vlan_name v31 mac_address 00- 00-00-00-00-11 command: delete address_binding blocked vlan_name v31 mac_address 00-00-00-00- 00-11 success. Des-3200-28p:admin# 31-4 ...

  • Page 317

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 313 parameters ipaddress - specify the ip address of the entry being updated. - enter the ip address used here. Mac_address - specify the mac address of the entry being updated - enter the mac address used here. Ports ...

  • Page 318

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 314 des-3200-28p:admin#show address_binding command: show address_binding trap/log : disabled dhcp snoop : disabled des-3200-28p:admin# to show the impb ports: des-3200-28p:admin#show address_binding ports command: sho...

  • Page 319

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 315 vlan_name - specify the name of the vlan to which the blocked mac address belongs. - enter the vlan name used. Mac_address - specify the mac address of the entry or the blocked mac address. - enter the mac address ...

  • Page 320

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 316 des-3200-28p:admin#show address_binding ip_mac all command: show address_binding ip_mac all m(mode) - d:dhcp, s:static acl - a:active i:inactive ip address mac address m acl ports ----------------------------------...

  • Page 321

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 317 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable dhcp ipv4 snooping mode: des-3200-28p:admin#enable address_binding dhcp_snoop command:...

  • Page 322

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 318 31-11 clear address_binding dhcp_snoop binding_entry ports description this command is used to clear the dhcp snooping entries learned for the specified ports. Format clear address_binding dhcp_snoop binding_entry ...

  • Page 323

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 319 example to show the dhcp snooping state: des-3200-28p:admin#show address_binding dhcp_snoop command: show address_binding dhcp_snoop dhcp_snoop : disabled des-3200-28p:admin# to display dhcp snooping maximun entry ...

  • Page 324

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 320 - enter the port number used here. Restrictions none. Example to display the dhcp snooping binding entries: des-3200-28p:admin#show address_binding dhcp_snoop binding_entry command: show address_binding dhcp_snoop ...

  • Page 325

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 321 example to set the maximum number of dhcp ipv4 snooping entries that ports 1–3 can learned to 10: des-3200-28p:admin#config address_binding dhcp_snoop max_entry ports 1-3 limit 10. Command: config address_binding d...

  • Page 326

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 322 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable impb traps and logs: des-3200-28p:admin#disable address_binding trap_log command: dis...

  • Page 328

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 324 example to stop impb debug: starting when the impb module receives an arp/ip or dhcp packet: des-3200-28p:admin#no debug address_binding command: no debug address_binding success. Des-3200-28p:admin#.

  • Page 330

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 326 32-2 delete ipv6 neighbor_cache description this command is used to delete a neighbor cache entry or static neighbor cache entries from the address cache or all address cache entries on this ip interface. Both stat...

  • Page 331

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 327 - enter the ip interface name here. This name can be up to 12 characters long. All - specify that all the interface will be displayed. Ipv6address - the neighbor’s address. - enter the ipv6 address here. Static - s...

  • Page 332

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 328 example to configure the retrans_time of ipv6 nd neighbor solicitation: des-3200-28p:admin#config ipv6 nd ns ipif zira retrans_time 1000000 command: config ipv6 nd ns ipif zira retrans_time 1000000 success. Des-320...

  • Page 335

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 331 des-3200-28p:admin#show ipv6route command: show ipv6route ipv6 prefix: ::/0 protocol: static metric: 1 next hop : 3001::254 ipif : system status : inactive total entries: 1 des-3200-28p:admin#.

  • Page 336: Chapter 34

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 332 chapter 34 jumbo frame command list enable jumbo_frame disable jumbo_frame show jumbo_frame 34-1 enable jumbo_frame description this command is used to configure the jumbo frame setting as enable. Format enable jum...

  • Page 337

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 333 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable the jumbo frame: des-3200-28p:admin#disable jumbo_frame command: disable jumbo_frame success. Des...

  • Page 339

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 335 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable the layer 2 protocol tunneling function: des-3200-28p:admin#disable l2protocol_tunnel command: di...

  • Page 340

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 336 01-00-0c-cc-cc-cd - specify the mac address as 01-00-0c-cc-cc-cd. All - all tunnel-abled layer 2 protocols will be tunneled on the ports. Threshold - (optional) specify the drop threshold for packets-per-second acc...

  • Page 341

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 337 des-3200-28p:admin#show l2protocol_tunnel command: show l2protocol_tunnel global state : enabled uni ports : 1-4 nni ports : des-3200-28p:admin# to show layer 2 protocol tunneling information summary: des-3200-28p:...

  • Page 343

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 339 36-2 delete link_aggregation group_id description this command is used to delete a previously configured link aggregation group. Format delete link_aggregation group_id parameters group_id - specify the group id. T...

  • Page 344

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 340 ports’ state machine will start. Enable - enable the specified link aggregation group. Disable - disable the specified link aggregation group. Restrictions only administrator, operator and power-user level users ca...

  • Page 345

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 341 des-3200-28p:admin#config link_aggregation algorithm mac_source_dest command: config link_aggregation algorithm mac_source_dest success. Des-3200-28p:admin# 36-5 show link_aggregation description this command is us...

  • Page 346

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 342 des-3200-28p:admin#show link_aggregation command: show link_aggregation link aggregation algorithm = mac-source-dest group id : 1 type : lacp master port : 5 member port : 5-7 active port : status : enabled floodin...

  • Page 347

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 343 passive - specify to set the lacp mode as passive. Restrictions only administrator, operator and power-user level users can issue this command. Example to config port lacp mode: des-3200-28p:admin#config lacp_port ...

  • Page 348

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 344 des-3200-28p:admin#show lacp_port command: show lacp_port port activity ------ -------- 1 active 2 active 3 active 4 active 5 active 6 active 7 active 8 active 9 active 10 active 11 active 12 active des-3200-28p:ad...

  • Page 350

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 346 restrictions only administrator, operator and power-user level users can issue this command. Example to enable lldp: des-3200-28p:admin#enable lldp command: enable lldp success. Des-3200-28p:admin# 37-2 disable lld...

  • Page 352

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 348 - enter the notification interval value here. This value must be between 5 and 3600 seconds. Restrictions only administrator, operator and power-user level users can issue this command. Example to changes the notif...

  • Page 353

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 349 mgt_addr - specify the management address used. Ipv4 - specify the ipv4 address used. - enter the ip address used for this configuration here. Ipv6 - specify the ipv6 address used. - enter the ipv6 address used for...

  • Page 354

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 350 eapol - (optional) specify that the eapol protocol will be advertised. Lacp - (optional) specify that the lacp protocol will be advertised. Gvrp - (optional) specify that the gvrp protocol will be advertised. Stp -...

  • Page 355

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 351 to enable ports 1-2 for manage address entry: des-3200-28p:admin#config lldp ports 1-2 mgt_addr ipv4 10.90.90.90 enable command: config lldp ports 1-2 mgt_addr ipv4 10.90.90.90 enable success. Des-3200-28p:admin# t...

  • Page 356

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 352 des-3200-28p:admin#config lldp ports all dot1_tlv_protocol_identity all enable command: config lldp ports all dot1_tlv_protocol_identity all enable success. Des-3200-28p:admin# to configure exclude the mac/phy conf...

  • Page 357

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 353 format show lldp parameters none. Restrictions none. Example to display the lldp system level configuration status: des-3200-28p:admin#show lldp command: show lldp lldp system information chassis id subtype : mac a...

  • Page 358

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 354 ipv6 - (optional) specify the ipv6 address used for the display. - enter the ipv6 address used for this configuration here. Restrictions none. Example to display management address information: des-3200-28p:admin#s...

  • Page 359

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 355 des-3200-28p:admin#show lldp ports 1 command: show lldp ports 1 port id : 1 ----------------------------------------------------------------- admin status : tx_and_rx notification status : enabled advertised tlvs o...

  • Page 360

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 356 example to display outbound lldp advertisements for port 1 in detailed mode. Port description on the display should use the same value as ifdescr. Des-3200-28p:admin#show lldp local_ports 1 mode detailed command: s...

  • Page 361

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 357 des-3200-28p:admin#show lldp local_ports 1 mode normal command: show lldp local_ports 1 mode normal port id : 1 ----------------------------------------------------------------------------- port id subtype : local ...

  • Page 362

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 358 brief - display the information in brief mode. Normal - display the information in normal mode. This is the default display mode. Detailed - display the information in detailed mode. Restrictions none. Example to d...

  • Page 363

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 359 to display remote table in normal mode: des-3200-28p:admin# show lldp remote_ports 3 mode normal command: show lldp remote_ports 3 mode normal port id : 3 -----------------------------------------------------------...

  • Page 364

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 360 des-3200-28p:admin# show lldp remote_ports 3 mode detailed command: show lldp remote_ports 3 mode detailed port id : 3 ------------------------------------------------------------------------------- remote entities...

  • Page 365

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 361 37-12 show lldp statistics description this command is used to display an overview of neighbor detection activity on the switch. Format show lldp statistics parameters none. Restrictions none. Example to display gl...

  • Page 366

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 362 example to display statistics information of port 1: des-3200-28p:admin#show lldp statistics ports 1 command: show lldp statistics ports 1 port id : 1 --------------------------------------------- lldpstatstxportfr...

  • Page 368

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 364 example to set the auto-recover time to 0, which disables the auto-recovery mechanism, the interval to 20 seconds and specify vlan-based mode: des-3200-28p:admin#config loopdetect recover_timer 0 interval 20 mode v...

  • Page 369

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 365 format enable loopdetect parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to enable the lbd function globally: des-3200-28p:admin#enable loopdete...

  • Page 370

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 366 des-3200-28p:admin#disable loopdetect command: disable loopdetect success. Des-3200-28p:admin# 38-5 show loopdetect description this command is used to display the lbd global configuration. Format show loopdetect p...

  • Page 371

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 367 parameters ports - specify the range of member ports that will display the lbd settings. - enter the list of port to be configured here. If no port is specified, the configuration for all ports will be displayed. R...

  • Page 372

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 368 example to specify that traps will be sent when the loop condition is detected or cleared: des-3200-28p:admin#config loopdetect trap both command: config loopdetect trap both success. Des-3200-28p:admin# 38-8 confi...

  • Page 374

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 370 parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to disable mac_notification function: des-3200-28p:admin#disable mac_notification command: disab...

  • Page 376

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 372 example to show the switch’s mac address table notification global settings: des-3200-28p:admin#show mac_notification command: show mac_notification global mac notification settings state : disabled interval : 1 hi...

  • Page 377

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 373 des-3200-28p:admin#show mac_notification ports command: show mac_notification ports port mac address table notification state ------ ------------------------------------ 1 disabled 2 disabled 3 disabled 4 disabled ...

  • Page 379

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 375 example to enable the mac-based access control global state: des-3200-28p:admin#enable mac_based_access_control command: enable mac_based_access_control success. Des-3200-28p:admin# 40-2 disable mac_based_access_co...

  • Page 380

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 376 parameters password - in radius mode, the switch will communicate with the radius server using this password. The maximum length of the key is 16. - enter the password used here. The default password is “default”. ...

  • Page 381

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 377 40-5 config mac_based_access_control guest_vlan description this command is used to assign a specified port list to the mac-based access control guest vlan. Ports that are not contained in port list will be removed...

  • Page 382

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 378 • before the authentication process starts, the user is able to forward traffic under the guest vlan. • after the authentication process, the user will be able to access the assigned vlan. If the port authorize mod...

  • Page 383

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 379 restrictions only administrator, operator and power-user level users can issue this command. Example to configure an unlimited number of maximum users for mac-based access control on ports 1 to 8: des-3200-28p:admi...

  • Page 384

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 380 example to create a mac-based access control guest vlan: des-3200-28p:admin#create mac_based_access_control guest_vlan vlan8 command: create mac_based_access_control guest_vlan vlan8 success. Des-3200-28p:admin# 40...

  • Page 386

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 382 parameters mac - specify the mac address that can pass local authentication. - enter the mac address used here. Vlan - (optional) specify the target vlan by using the vlan name. When this host is authorized, it wil...

  • Page 387

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 383 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the target vlan “default” for the mac-based access control local database entry 00- 00-00-00-00-01: ...

  • Page 388

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 384 to delete the mac-based access control local database entry for the vlan name vlan3: des-3200-28p:admin#delete mac_based_access_control_local vlan vlan3 command: delete mac_based_access_control_local vlan vlan3 suc...

  • Page 389

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 385 40-14 show mac_based_access_control description this command is used to display the mac-based access control setting. Format show mac_based_access_control {ports {}} parameters ports – (optional) displays the mac-b...

  • Page 390

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 386 address. - enter the mac address used here. Vlan - (optional) displays mac-based access control local database entries for a specific target vlan name. - enter the vlan name here. This name can be up to 32 characte...

  • Page 391

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 387 des-3200-28p:admin#show mac_based_access_control auth_state ports 1-4 command: show mac_based_access_control auth_state ports 1-4 (p): port-based port mac address state vid priority aging time/ block time ---- ----...

  • Page 393

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 389 example to disable log state of mac-based access control: des-3200-28p:admin#config mac_based_access_control log state disable command: config mac_based_access_control log state disable success. Des-3200-28p:admin#.

  • Page 396

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 392 vlan - (optional) specify the vlan that you would like to display. - enter the vlan name here. This name can be up to 32 characters long. Vlanid - (optional) specify the vlan by vlan id. - enter the vlan id here. T...

  • Page 398

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 394 42-2 enable mirror description this command is used to enable mirror function without having to modify the mirror session configuration. Format enable mirror parameters none. Restrictions only administrator and ope...

  • Page 399

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 395 example to disable mirroring function: des-3200-28p:admin#disable mirror command: disable mirror success. Des-3200-28p:admin# 42-4 show mirror description this command is used to display the current mirror function...

  • Page 401

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 397 43-2 debug stp show information description this command is used to display stp detailed information, such as the hardware tables, the stp state machine, etc. Format debug stp show information parameters none. Rest...

  • Page 402

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 398 43-3 debug stp show flag description this command is used to display the stp debug level on specified ports. Format debug stp show flag {ports } parameters ports - (optional) specify the stp ports to display. - (op...

  • Page 403

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 399 22 disabled disabled disabled 23 disabled disabled disabled 24 disabled disabled disabled 25 disabled disabled disabled 26 disabled disabled disabled 27 disabled disabled disabled 28 disabled disabled disabled des-...

  • Page 404

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 400 des-3200-28p:admin#debug stp show counter ports 9 command: debug stp show counter ports 9 stp counters -------------------------------------- port 9 : receive: transmit: total stp packets : 0 total stp packets : 0 ...

  • Page 405

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 401 des-3200-28p:admin#debug stp clear counter ports all command: debug stp clear counter ports all success. Des-3200-28p:admin# 43-6 debug stp state description this command is used to enable or disable the stp debug ...

  • Page 407

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 403 des-3200-28p:admin#create mcast_filter_profile profile_id 2 profile_name mod command: create mcast_filter_profile profile_id 2 profile_name mod success. Des-3200-28p:admin# 44-2 config mcast_filter_profile descript...

  • Page 409

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 405 - enter the profile id value here. This value must be between 1 and 24. All - all multicast address profiles will be deleted. Profile_name - specify to display a profile based on the profile name. - enter the profi...

  • Page 410

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 406 example to display all the defined multicast address profiles: des-3200-28p:admin#show mcast_filter_profile command: show mcast_filter_profile profile id name multicast addresses ---- ---------------- -------------...

  • Page 411

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 407 restrictions only administrator, operator and power-user level users can issue this command. Example to add multicast address profile 2 to ports 1 and 3: des-3200-28p:admin#config limited_multicast_addr ports 1,3 a...

  • Page 412

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 408 example to configure the maximum number of multicast group that ports 1 and 3 can join to 100: des-3200-28p:admin#config max_mcast_group ports 1, 3 max_group 100 command: config max_mcast_group ports 1, 3 max_group...

  • Page 413

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 409 to display the maximum number of multicast groups that vlans 1 and 2 can join: des-3200-28p:admin#show max_mcast_group vlanid 1-2 command: show max_mcast_group vlanid 1-2 vlan max multicast group number action ----...

  • Page 414

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 410 des-3200-28p:admin#show limited_multicast_addr ports 1,3 command: show limited_multicast_addr ports 1,3 port : 1 access : deny profile id name multicast addresses ----------- ----------- ---------------------------...

  • Page 415

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 411 igmp_query - (optional) specify to filter the igmp query control packets. Ospf - (optional) specify to filter the ospf control packets. Rip - (optional) specify to filter the rip control packets. Vrrp - (optional) ...

  • Page 416

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 412 des-3200-28p:admin#show cpu_filter l3_control_pkt ports 1-2 command: show cpu_filter l3_control_pkt ports 1-2 port igmp query dvmrp pim ospf rip vrrp ---- ---------- -------- -------- -------- -------- -------- 1 d...

  • Page 418

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 414 - the vlan id of the multicast vlan to be created. This value must be between 2 and 4094. Remap_priority - (optional) the remap priority (0 to 7) to be associated with the data traffic to be forwarded on the multic...

  • Page 419

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 415 - enter the list of port to be configured here. Untag_source_port - specify the source port or range of source ports as untagged members of the multicast vlan. The pvid of the untagged source port is automatically ...

  • Page 420

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 416 to 32 characters long. Restrictions only administrator, operator and power-user level users can issue this command. Example to create an igmp snooping multicast group profile with the name “test”: des-3200-28p:admi...

  • Page 421

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 417 des-3200-28p:admin#config igmp_snooping multicast_vlan_group_profile test add 225.1.1.1 command: config igmp_snooping multicast_vlan_group_profile test add 225.1.1.1 success. Des-3200-28p:admin# 45-5 delete igmp_sn...

  • Page 422

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 418 parameters - (optional) enter the multicast vlan group profile name here. The name can be up to 32 characters long. Restrictions none. Example to display all igmp snooping multicast vlan profiles: des-3200-28p:admi...

  • Page 423

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 419 parameters - enter the multicast vlan name here. The vlan name can be up to 32 characters long. Add - used to associate a profile to a multicast vlan. Delete - used to de-associate a profile from a multicast vlan. ...

  • Page 424

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 420 des-3200-28p:admin#show igmp_snooping multicast_vlan_group command: show igmp_snooping multicast_vlan_group vlan name vlan id multicast group profiles ------------------------------- ------- -----------------------...

  • Page 425

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 421 parameters none. Restrictions only administrator-level users can issue this command. Example to enable the igmp snooping multicast vlan function globally: des-3200-28p:admin#enable igmp_snooping multicast_vlan comm...

  • Page 426

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 422 45-12 config igmp_snooping multicast_vlan forward_unmatched description this command is used to configure the forwarding mode for multicast vlan unmatched packets. When the switch receives an igmp snooping packet, ...

  • Page 427

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 423 example to display all igmp snooping multicast vlans: des-3200-28p:admin#show igmp_snooping multicast_vlan command: show igmp_snooping multicast_vlan igmp multicast vlan global state : disabled igmp multicast vlan ...

  • Page 429

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 425 des-3200-28p:admin#enable stp command: enable stp success. Des-3200-28p:admin# 46-2 disable stp description this command is used to disable stp globally. Format disable stp parameters none. Restrictions only admini...

  • Page 430

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 426 - enter the maximum age value here. This value must be between 6-40. Maxhops - (optional) used to restrict the forwarded times of one bpdu. The default value is 20. - enter the maximum hops value here. This value m...

  • Page 431

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 427 restrictions none. Example to show stp: des-3200-28p:admin#show stp command: show stp stp bridge global settings --------------------------- stp status : enabled stp version : rstp max age : 25 hello time : 2 forwa...

  • Page 432

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 428 des-3200-28p:admin#create stp instance_id 2 command: create stp instance_id 2 success. Des-3200-28p:admin# 46-6 config stp instance_id description this command is used to map or remove the vlan range of the specifi...

  • Page 433

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 429 46-7 delete stp instance_id description this command is used to delete an mst instance. Format delete stp instance_id parameters instance_id - specify the mstp instance id. Instance 0 represents for default instanc...

  • Page 434

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 430 example to change the name and revision level of the mst configuration identification: des-3200-28p:admin#config stp mst_config_id name r&d_blockg revision_level 1 commands: config stp mst_config_id name r&d_blockg...

  • Page 436

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 432 hellotime - (optional) the default value is 2 . This parameter is for mstp version. For stp and rstp version, uses the per system hellotime parameter. - enter the hello time value here. This value must be between 1...

  • Page 437

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 433 format show stp ports {} parameters ports - to show parameters of the designated port numbers, to be distinguished from showing parameters of the bridge. - (optional) enter a list of ports used for the configuratio...

  • Page 438

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 434 parameters priority - specify the bridge priority value. This value must be divisible by 4096. - enter the bridge priority value here. This value must be between 0 and 61440. Instance_id - identifier to distinguish...

  • Page 439

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 435 to config stp version with the same value of old configuration: des-3200-28p:admin#config stp version mstp command: config stp version mstp configure value is the same with current value. Success. Des-3200-28p:admi...

  • Page 440

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 436 des-3200-28p:admin#show stp instance command: show stp instance stp instance settings --------------------------- instance type : cist instance status : enabled instance priority : 32768(bridge priority : 32768, sy...

  • Page 443

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 439 example to delete the nlb unicast fdb entry, for the product that support the vlan information on the unicast forwarding: des-3200-28p:admin#delete nlb unicast_fdb 02-bf-01-01-01-01 command: delete nlb unicast_fdb ...

  • Page 445

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 441 example to delete nlb multicast fdb entry: des-3200-28p:admin#delete nlb multicast_fdb default 03-bf-01-01-01-01 command: delete nlb multicast_fdb default 03-bf-01-01-01-01 success. Des-3200-28p:admin# 47-7 show nl...

  • Page 447

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 443 des-3200-28p:admin#show packet ports 7 command: show packet ports 7 port number : 7 ================================================================== frame size/type frame counts frames/sec --------------- -------...

  • Page 448

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 444 des-3200-28p:admin#show error ports 3 command: show error ports 3 port number : 3 rx frames tx frames --------- --------- crc error 0 excessive deferral 0 undersize 0 crc error 0 oversize 0 late collision 0 fragmen...

  • Page 449

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 445 des-3200-28p:admin#show utilization ports command: show utilization ports port tx/sec rx/sec util port tx/sec rx/sec util ----- ---------- ---------- ---- ----- ---------- ---------- ---- 1 0 0 0 21 0 0 0 2 0 0 0 2...

  • Page 450

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 446 des-3200-28p:admin#show utilization cpu command: show utilization cpu cpu utilization ------------------------------------------------------------------------------- five seconds - 10 % one minute - 10 % five minut...

  • Page 451

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 447 des-3200-52p:admin#show utilization dram command: show utilization dram dram utilization : total dram : 131072 kb used dram : 115758 kb utilization : 88 % ctrl+c esc q quit space n next page p previous page r refre...

  • Page 452

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 448 format clear counters {ports } parameters ports - (optional) specify a range of ports to be configured. The port list is specified by listing the lowest switch number and the beginning port number on that switch, s...

  • Page 455

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 451 critical_link_event –specify critical link event. Dying_gasp - an unrecoverable local failure condition has occurred. Critical_event - an unspecified critical event has occurred. Notify_state - specify the event no...

  • Page 456

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 452 des-3200-28p:admin#config ethernet_oam ports 1 link_monitor error_frame threshold 2 window 1000 notify_state enable command: config ethernet_oam ports 1 link_monitor error_frame threshold 2 window 1000 notify_state...

  • Page 457

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 453 des-3200-28p:admin#config ethernet_oam ports 1 received_remote_loopback process command: config ethernet_oam ports 1 received_remote_loopback process success. Des-3200-28p:admin# 49-2 show ethernet_oam ports descri...

  • Page 458

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 454 the event log displays ethernet oam event log information. The switch can buffer 1000 event logs. The event log is different from sys-log as it provides more detailed information than sys-log. Each oam event will b...

  • Page 461

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 457 format show environment parameters none. Restrictions none. Example to display the device environment: des-3200-28p:admin#show environment command: show environment temperature trap state : enabled temperature log ...

  • Page 462

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 458 example to configure the warning temperature threshold: des-3200-28p:admin#config temperature threshold high 80 command: config temperature threshold high 80 success. Des-3200-28p:admin# 50-4 config temperature des...

  • Page 464

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 460 51-2 ping6 description this command is used to send ipv6 internet control message protocol (icmp) echo messages to a remote ipv6 address. The remote ipv6 address will then “echo” or return the message. This is used...

  • Page 466

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 462 des-3200-28p:admin#config port_security system max_learning_addr 256 command: config port_security system max_learning_addr 256 success. Des-3200-28p:admin# 52-2 config port_security ports description this command ...

  • Page 467

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 463 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the port-based port security setting so that the maximum number of port security entries is restrict...

  • Page 468

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 464 des-3200-28p:admin#config port_security vlan vlanid 1 max_learning_addr 64 command: config port_security vlan vlanid 1 max_learning_addr 64 success. Des-3200-28p:admin# 52-4 delete port_security_entry description t...

  • Page 469

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 465 parameters ports - (optional) specify the range of ports to be configured. - the port security entries learned on the specified port will be cleared. All - all the port security entries learned by the system will b...

  • Page 470

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 466 example to show all the port security entries: des-3200-28p:admin#show port_security_entry command: show port_security_entry mac address vid port lock mode ----------------- ---- ----- --------------- 00-00-00-00-0...

  • Page 471

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 467 des-3200-28p:admin#show port_security command: show port_security port security trap/log : disabled system maximum address : 256 vlan configuration (only vlans with limitation are displayed) vid vlan name max. Lear...

  • Page 472

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 468 format disable port_security trap_log parameters none. Restrictions only administrator, operator and power-user level users can issue this command. Example to prevent a port security trap from being sent from the s...

  • Page 474

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 470 disconnect_method is set to deny_low_priority_port, then the power provision can utilize the system’s maximum power. Legacy_pd - configure legacy pds detection status, enable for support, if set to disable, can’t d...

  • Page 475

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 471 parameters ports - specify the list of ports whose setting is under configuration. All - specify that all the ports will be included in this configuration. - enter the list of port used for this configuration here....

  • Page 476

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 472 53-3 show poe system description this command is used to display the setting and actual values of the whole poe system. Format show poe system parameters none. Restrictions none. Example to display poe system: des-...

  • Page 477

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 473 parameters - (optional) specify a list of ports to be displayed. If no parameter specified, the system will display the status for all ports. Restrictions none. Example to display poe port: des-3200-28p:admin#show ...

  • Page 479

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 475 54-2 config pppoe circuit_id_insertion ports description this command is used to configure port’s pppoe circuit id insertion function. When the port’s state and the global state are enabled, the system will insert ...

  • Page 480

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 476 parameters none. Restrictions none. Example to display pppoe circuit id insertion status: des-3200-28p:admin#show pppoe circuit_id_insertion command: show pppoe circuit_id_insertion global pppoe state: enabled des-...

  • Page 481

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 477 des-3200-28p:admin#show pppoe circuit_id_insertion ports 2-5 command: show pppoe circuit_id_insertion ports 2-5 port state circuit id ---- -------- --------------------------------------------- 2 enabled switch ip ...

  • Page 483

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 479 55-2 config dot1v_protocol_group add protocol description this command is used to add a protocol to a protocol group. The selection of a protocol can be a pre-defined protocol type or a user defined protocol. Forma...

  • Page 484

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 480 parameters group_id - specify the group id to be deleted. - enter the group id used here. Group_name - specify the name of the group to be deleted. - enter the group name here. This name can be up to 32 characters ...

  • Page 485

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 481 des-3200-28p:admin#show dot1v_protocol_group group_id 10 command: show dot1v_protocol_group group_id 10 protocol group id protocol group name frame type protocol value ----------------- ----------------------------...

  • Page 486

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 482 restrictions only administrator, operator and power-user level users can issue this command. Example the example is to assign vlan marketing-1 for untaged ipv6 packet ingress from port 3. To configure the group id ...

  • Page 487

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 483 des-3200-28p:admin#show port dot1v ports 1 command: show port dot1v ports 1 port: 1 protocol group id vlan name protocol priority ------------------- --------------------------------- ----------------- 1 default - ...

  • Page 489

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 485 56-2 disable qinq description this command is used to disable the qinq. When qinq is disabled, all dynamic learned l2 addresses will be cleared, all dynamic registered vlan entries will be cleared, and gvrp will be...

  • Page 490

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 486 example to configure the inner tpid in the system to 0x9100: des-3200-28p:admin#config qinq inner_tpid 0x9100 command: config qinq inner_tpid 0x9100 success. Des-3200-28p:admin# 56-4 config qinq ports description t...

  • Page 491

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 487 des-3200-28p:admin#config qinq ports 1-4 role nni outer_tpid 0x88a8 command: config qinq ports 1-4 role nni outer_tpid 0x88a8 success. Des-3200-28p:admin# 56-5 show qinq description this command is used to display ...

  • Page 492

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 488 restrictions none. Example to display the inner-tpid of a system: des-3200-28p:admin#show qinq inner_tpid command: show qinq inner_tpid inner tpid: 0x9100 des-3200-28p:admin# 56-7 show qinq ports description this c...

  • Page 493

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 489 des-3200-28p:admin#show qinq ports 1-2 command: show qinq ports 1-2 port id: 1 --------------------------------------------------------- role: nni miss drop: disabled outer tpid: 0x8100 add inner tag: disabled port...

  • Page 494

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 490 restrictions only administrator, operator and power-user level users can issue this command. Example to replace the c-tag in which the cvid is 20, with the s-tag and the s-vid is 200 at uni port 1: des-3200-28p:adm...

  • Page 495

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 491 des-3200-28p:admin#delete vlan_translation ports 1-4 command: delete vlan_translation ports 1-4 success. Des-3200-28p:admin# 56-10 show vlan_translation description this command is used to display the existing c-vl...

  • Page 497

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 493 command is executed. - enter the transmitting data rate here. This value must be between 64 and 1024000. Restrictions only administrator, operator and power-user level users can issue this command. Example to confi...

  • Page 498

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 494 des-3200-28p:admin#show bandwidth_control 1-10 command: show bandwidth_control 1-10 bandwidth control table port rx rate tx rate effective rx effective tx (kbit/sec) (kbit/sec) (kbit/sec) (kbit/sec) ----- ---------...

  • Page 499

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 495 receive. If the specified rate is not multiple of minimum granularity, the rate will be adjusted. Restrictions only administrator level can issue this command. Example to configure the ports 1-10 cos bandwidth queu...

  • Page 500

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 496 des-3200-28p:admin#show per_queue bandwidth_control 10 command: show per_queue bandwidth_control 10 queue bandwidth control table on port: 10 queue min rate(kbit/sec) max rate(kbit/sec) 0 640 no limit 1 640 no limi...

  • Page 502

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 498 parameters - (optional) specify a range of ports to be displayed. If no parameter specified, system will display all ports scheduling configurations. Restrictions none. Example to display the traffic scheduling par...

  • Page 503

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 499 example to show scheduling mechanism: des-3200-28p:admin#show scheduling_mechanism command: show scheduling_mechanism port mode ----- ------ 1 strict 2 strict 3 strict 4 strict 5 strict 6 strict 7 strict 8 strict 9...

  • Page 504

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 500 parameters - the 802.1p user priority you want to associate with the (the number of the hardware queue) with. - the number of the switch’s hardware priority queue. The switch has 8 hardware priority queues availabl...

  • Page 505

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 501 des-3200-28p:admin#show 802.1p user_priority command: show 802.1p user_priority qos class of traffic: priority-0 -> priority-1 -> priority-2 -> priority-3 -> priority-4 -> priority-5 -> priority-6 -> priority-7 -> ...

  • Page 506

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 502 57-12 show 802.1p default_priority description this command is used to display the current configured default priority settings on the switch. The default priority can also be assigned by the radius server through ...

  • Page 508

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 504 green - specify green as the mapped color. Red - specify red as the mapped color. Yellow - specify yellow as the mapped color. Restrictions only administrator, operator and power-user level users can issue this com...

  • Page 509

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 505 57-16 show dscp trust description this command is used to display dscp trust state for the specified ports on the switch. Format show dscp trust {} parameters - (optional) a range of ports to display. If not specif...

  • Page 513

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 509 example to configure cpu protection: des-3200-28p:admin#config safeguard_engine state enable utilization rising 50 falling 30 trap_log enable command: config safeguard_engine state enable utilization rising 50 fall...

  • Page 515

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 511 example to enable ssh server public key algorithm: des-3200-28p:admin#config ssh algorithm dsa enable command: config ssh algorithm dsa enable success. Des-3200-28p:admin# 59-2 show ssh algorithm description this c...

  • Page 516

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 512 des-3200-28p:admin#show ssh algorithm command: show ssh algorithm encryption algorithm -------------------------- 3des : enabled aes128 : enabled aes192 : enabled aes256 : enabled arcfour : enabled blowfish : enabl...

  • Page 517

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 513 example to configure user authentication method: des-3200-28p:admin#config ssh authmode publickey enable command: config ssh authmode publickey enable success. Des-3200-28p:admin# 59-4 show ssh authmode description...

  • Page 519

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 515 example to show user information about ssh configuration: des-3200-28p:admin#show ssh user authmode command: show ssh user authmode current accounts username authmode hostname hostip ------------- ------------- ---...

  • Page 520

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 516 example to configure ssh server maximum session number is 3: des-3200-28p:admin#config ssh server maxsession 3 command: config ssh server maxsession 3 success. Des-3200-28p:admin# 59-8 enable ssh description this c...

  • Page 521

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 517 restrictions only administrator, operator and power-user level users can issue this command. Example to disable the ssh server services: des-3200-28p:admin#disable ssh command: disable ssh success. Des-3200-28p:adm...

  • Page 523

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 519 des-3200-28p:admin#download ssl certificate 10.55.47.1 certfilename cert.Der keyfilename pkey.Der command: download ssl certificate 10.55.47.1 certfilename cert.Der keyfilename pkey.Der success. Des-3200-28p:admin#...

  • Page 524

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 520 des-3200-28p:admin#enable ssl command: enable ssl success. Des-3200-28p:admin# note: web will be disabled when ssl is enabled. 60-3 disable ssl description this command is used to disable ssl feature and supported ...

  • Page 525

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 521 des-3200-28p:admin#disable ssl command: disable ssl success. Des-3200-28p:admin# 60-4 show ssl description this command is used to display the certificate status. User must download specified certificate type accor...

  • Page 526

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 522 60-5 show ssl cachetimeout description this command is used to show cahce timeout value which is designed for dlktimer library to remove the session id after expired. In order to support the resume session feature,...

  • Page 527

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 523 restrictions only administrator, operator and power-user level users can issue this command. Example to configure the ssl cache timeout value to 60: des-3200-28p:admin#config ssl cachetimeout 60 commands: config ss...

  • Page 528: Chapter 61

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 524 chapter 61 show technical support command list show tech_support upload tech_support_totftp { } 61-1 show tech_support description this command is especially used by the technical support personnel to dump the devi...

  • Page 529

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 525 des-3200-28p:admin#show tech_support command: show tech_support #------------------------------------------------------------------------------ # des-3200-28p fast ethernet switch # technical support information # ...

  • Page 530

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 526 format upload tech_support_totftp { } parameters - (optional) specify the ip address of tftp server. - specify the file name to store the information of technique’s support in tftp server. The max size of the file ...

  • Page 532

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 528 format disable smtp parameters none. Restrictions only administrator-level users can issue this command. Example to disable smtp status: des-3200-28p:admin#disable smtp command: disable smtp success. Des-3200-28p:a...

  • Page 533

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 529 example to configure a smtp server ip address: des-3200-28p:admin#config smtp server 172.18.208.9 command: config smtp server 172.18.208.9 success. Des-3200-28p:admin# to configure an smtp server port: des-3200-28p...

  • Page 534

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 530 format show smtp parameters none. Restrictions none. Example to display the current smtp information: des-3200-28p:admin#show smtp command: show smtp smtp status : disabled smtp server address : 172.18.208.9 smtp s...

  • Page 535

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 531 restrictions only administrator-level users can issue this command. Example to test whether the smtp server can be reached: des-3200-28p:admin#smtp send_testmsg command: smtp send_testmsg subject:e-mail heading con...

  • Page 537

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 533 an access list of ip addresses of the snmp managers that are permitted to use the community string to gain access to the agent. A mib view, which defines the subset of all mib objects accessible to the given commun...

  • Page 538

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 534 parameters community - community string will be deleted. - enter the community string value here. This value can be up to 32 characters long. Restrictions only administrator-level users can issue this command. Exam...

  • Page 539

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 535 des-3200-28p:admin#show snmp community command: show snmp community snmp community table community name view name access right ------------------------------- ---------------------- ------------ private communityvi...

  • Page 540

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 536 des - specify that the des encryption will be used for the privacy key. - enter the des privacy key here. This value must be 32 characters long. Restrictions only administrator-level users can issue this command. E...

  • Page 541

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 537 63-6 show snmp user description this command is used to display information on each snmp username in the group username table. Format show snmp user parameters none. Restrictions none. Example to show snmp user: de...

  • Page 542

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 538 v2c - the second least secure of the possible security models. V3 - the most secure of the possible. Noauth_nopriv - neither support packet authentication nor encrypting. Auth_nopriv - support packet authentication...

  • Page 543

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 539 des-3200-28p:admin#delete snmp group group123 command: delete snmp group group123 success. Des-3200-28p:admin# 63-9 show snmp groups description this command is used to display the names of groups on the switch and...

  • Page 544

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 540 des-3200-28p:admin#show snmp groups command: show snmp groups vacm access table settings group name : public readview name : communityview writeview name : notify view name : communityview securiy model : snmpv1 se...

  • Page 545

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 541 - object-identified tree, mib tree. View_type - specify the access type of the mib tree in this view. Included - includes for this view. Excluded - excluded for this view. Restrictions only administrator-level user...

  • Page 546

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 542 63-12 show snmp view description this command is used to display the snmp view record. Format show snmp view {} parameters view - (optional) view name of the user who likes to show. - enter the view name here. The ...

  • Page 547

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 543 parameters - the ip address of the recipient for which the traps are targeted. V1 - the least secure of the possible security models. V2c - the second least secure of the possible security models. V3 - the most sec...

  • Page 548

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 544 des-3200-28p:admin#delete snmp host 10.0.0.1 command: delete snmp host 10.0.0.1 success. Des-3200-28p:admin# 63-15 show snmp host description this command is used to display the recipient for which the traps are ta...

  • Page 549

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 545 format config snmp engineid parameters engineid - identify for the snmp engine on the switch. It is octet string type. It accepts the hex number directly. - enter the snmp engine id here. This value must be between...

  • Page 550

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 546 des-3200-28p:admin#show snmp engineid command: show snmp engineid snmp engine id : 1023457890 des-3200-28p:admin# 63-18 enable snmp description this command is used to enable the snmp function. Format enable snmp p...

  • Page 551

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 547 restrictions only administrator and operator-level users can issue this command. Example to disable snmp: des-3200-28p:admin#disable snmp command: disable snmp success. Des-3200-28p:admin# 63-20 config snmp system_...

  • Page 552

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 548 format config snmp system_location {} parameters system_location - a maximum of 128 characters is allowed. And null string is accepted - (optional) enter the system location string here. Restrictions only administr...

  • Page 553

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 549 63-23 enable snmp traps description this command is used to enable snmp trap support. Format enable snmp traps parameters none. Restrictions only administrator and operator-level users can issue this command. Examp...

  • Page 554

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 550 des-3200-28p:admin#disable snmp traps command: disable snmp traps success. Des-3200-28p:admin# 63-25 enable snmp authenticate_traps description this command is used to enable snmp authentication failure trap suppor...

  • Page 555

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 551 restrictions only administrator and operator-level users can issue this command. Example to disable snmp authentication trap support: des-3200-28p:admin#disable snmp authenticate_traps command: disable snmp authent...

  • Page 556

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 552 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to disable the sending of linkchange traps: des-3200-28p:admin#disable snmp linkchange_traps command: disabl...

  • Page 558

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 554 example to configure the trap state for warmstart event: des-3200-28p:admin#config snmp warmstart_traps enable command: config snmp warmstart_traps enable success. Des-3200-28p:admin# 63-32 show snmp traps descript...

  • Page 560

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 556 des-3200-28p:admin#show rmon command: show rmon rmon rising alarm trap : enabled rmon falling alarm trap : enabled des-3200-28p:admin#.

  • Page 562

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 558 64-2 disable sim description this command is used to disable single ip management on the switch. Format disable sim parameters none. Restrictions only administrator-level users can issue this command. Example to di...

  • Page 563

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 559 restrictions none. Example to show the self information in detail: des-3200-28p:admin#show sim command: show sim sim version : ver-1.61 firmware version : 4.03.004 device name : des-3200-28p mac address : 00-01-02-...

  • Page 564

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 560 des-3200-28p:admin#show sim member command: show sim member id mac address platform / hold firmware device name capability time version --- ----------------- ------------------------ ----- --------- ---------------...

  • Page 565

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 561 des-3200-28p:admin#show sim neighbor command: show sim neighbor neighbor table port mac address role ------ ------------------ --------- 23 00-35-26-00-11-99 commander 23 00-35-26-00-11-91 member 24 00-35-26-00-11-...

  • Page 568

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 564 des-3200-28p:admin#config sim dp_interval 30 command: config sim dp_interval 30 success. Des-3200-28p:admin# to change the hold time of discovery protocol: des-3200-28p:admin#config sim hold_time 200 command: confi...

  • Page 569

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 565 des-3200-28p:admin#download sim_ms configuration_from_tftp 10.55.47.1 d:\dwl600x.Tfp members 1 commands: download sim_ms configuration_from_tftp 10.55.47.1 d:\dwl600x.Tfp members 1 this device is updating configura...

  • Page 570

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 566 restrictions only administrator-level users can issue this command. Example to upload configuration: des-3200-28p:admin#upload sim_ms configuration_to_tftp 10.55.47.1 d:\configuration.Txt members 1 command: upload ...

  • Page 572

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 568 des-3200-28p:admin#config syslog source_ipif none command: config syslog source_ipif none success des-3200-28p:admin# 65-2 show syslog source_ipif description this command is used to display the syslog source ip in...

  • Page 573

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 569 parameters ipif - specify the ip interface name. If only specify this parameter, the least ipv4 address and the smallest ipv6 address of ipif_name will be used as source ip addresses. - enter the ip interface name ...

  • Page 574

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 570 example show trap source ip interface: des-3200-28p:admin#show trap source_ipif command: show trap source_ipif trap source ip interface configuration: ip interface : system ipv4 address : none des-3200-28p:admin#.

  • Page 577

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 573 des-3200-28p:admin#show log index 1-3 command: show log index 1-3 index date time level log text ----- ---------- -------- ------- ---------------------------------------------- 3 2000-01-01 00:00:40 crit(2) system...

  • Page 578

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 574 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to enable the sending of syslog messages: des-3200-28p:admin#enable syslog command: enable syslog success. D...

  • Page 579

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 575 66-6 show syslog description this command is used to display the syslog protocol global state. Format show syslog parameters none. Restrictions none. Example to display the syslog protocol global state: des-3200-28...

  • Page 580

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 576 error - severity level 3 warning - severity level 4 notice - severity level 5 informational - severity level 6 debug - severity level 7 - enter the severity level value here. This value must be between 0 and 7. Fac...

  • Page 583

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 579 example to show the syslog host information: des-3200-28p:admin#show syslog host command: show syslog host syslog global state: disabled host 1 ip address : 10.90.90.1 severity : debug(7) facility : local0 udp port...

  • Page 584

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 580 66-12 show log_save_timing description this command is used to show the method for saving the log. Format show log_save_timing parameters none. Restrictions none. Example to show the timing method used for saving t...

  • Page 585

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 581 restrictions none. Example to show dangerous messages on the master: des-3200-28p:admin#show attack_log index 1 command: show attack_log index 1 index date time level log text ----- ---------- -------- -------- ---...

  • Page 587

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 583 67-2 show system_severity description this command is used to display the severity level controls for the system. Format show system_severity parameters none. Restrictions none. Example to show severity level contr...

  • Page 588: Chapter 68

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 584 chapter 68 telnet client command list telnet {tcp_port } 68-1 telnet description this command is used to start the telnet client to connect to the specific telnet server. The parameters specified by the command wil...

  • Page 590

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 586 parameters firmware_fromtftp – specify to download firmware from a tftp server. - (optional) the ip address of the tftp server. Src_file - (optional) used to identify the parameter “path_filename”. - enter the sour...

  • Page 591

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 587 des-3200-28p:admin#download firmware_fromtftp 10.54.71.1 src_file px.Had command: download firmware_fromtftp 10.54.71.1 src_file px.Had connecting to server................... Done. Download firmware..................

  • Page 592

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 588 long. Src_file - (optional) used to identify the parameter “path_filename”. - the pathname specifies an absolute pathname on the device file system. Include - (optional) specify to include lines that contain the sp...

  • Page 593

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 589 src_file - (optional) used to identify the parameter “path_filename”. - the pathname specifies an absolute pathname on the device file system. If pathname is not specified, it refers to the boot_up image. This name...

  • Page 594

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 590 dest_file - used to identify the parameter “path_filename”. - the pathname specifies the pathname on the ftp server. It can be a relative pathname or an absolute pathname. This name can be up to 64 characters long....

  • Page 595

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 591 des-3200-28p:admin#upload firmware_totftp 10.90.90.10 dest_file d:/firmware.Had src_file 4.00.020.Had command: upload firmware_totftp 10.90.90.10 dest_file d:/firmware.Had src_file 4.00.020.Had no such file or dire...

  • Page 597

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 593 des-3200-28p:admin#config tftp server 10.90.90.10 command: config tftp server 10.90.90.10 success. Des-3200-28p:admin# to configure tftp server and specify the pre defined firmware file, log file: des-3200-28p:admi...

  • Page 598

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 594 des-3200-28p:admin#show tftp command: show tftp tftp server settings ipv4 address : 10.90.90.1 file type path_filename -------------------- ---------------------- firmware_file des3200.Had cfg_file log_tmp log_file...

  • Page 600

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 596 des-3200-28p:admin#config sntp primary 10.1.1.1 secondary 10.1.1.2 poll- interval 30 command: config sntp primary 10.1.1.1 secondary 10.1.1.2 poll-interval 30 success. Des-3200-28p:admin# 70-2 show sntp description...

  • Page 601

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 597 parameters none. Restrictions only administrator and operator-level users can issue this command. Example to enable sntp: des-3200-28p:admin#enable sntp command: enable sntp success. Des-3200-28p:admin# 70-4 disabl...

  • Page 602

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 598 format config time parameters - specify the system clock date. An example would look like this: '30jun2010'. - specify the system clock time. An example would look like this: '12:00:00'. Restrictions only administr...

  • Page 603

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 599 example to configure time_zone: des-3200-28p:admin#config time_zone operator + hour 2 min 30 command: config time_zone operator + hour 2 min 30 success. Des-3200-28p:admin# 70-7 config dst description this command ...

  • Page 604

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 600 annual - set the daylight saving time to annual mode. S_date, e_date - (optional) configure the start /end date of daylight saving time. - enter the starting date of daylight saving time here. This range must be be...

  • Page 605

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 601 restrictions none. Example to show time: des-3200-28p:admin#show time command: show time current time source : system clock boot time : 9 may 2011 06:20:55 current time : 9 may 2011 07:46:10 time zone : gmt +00:00 ...

  • Page 607

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 603 des-3200-28p:admin#traceroute 10.48.74.121 probe 3 command: traceroute 10.48.74.121 probe 3 1 2 3 trace complete. Des-3200-28p:admin# 71-2 traceroute6 description this command is used to trace the ipv6 routed path ...

  • Page 608

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 604 des-3200-28p:admin#traceroute6 3000::1 probe 3 command: traceroute6 3000::1 probe 3 1 2 3 trace complete. Des-3200-28p:admin# trace the ipv6 routed path between the switch and 1210:100::11 with port 40000: des-3200...

  • Page 610

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 606 countdown - (optional) timer for shutdown mode. If a port enters the shutdown rx state and this timer runs out, port will be shutdown forever. The parameter is not applicable if “drop” (mode) is specified for the “...

  • Page 611

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 607 example to enable both the occurred mode and cleared mode traffic control traps: des-3200-28p:admin#config traffic trap both command: config traffic trap both success. Des-3200-28p:admin# 72-3 show traffic control ...

  • Page 612

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 608 des-3200-28p:admin#show traffic control 1-10 command: show traffic control 1-10 traffic control trap : [both] traffic control log : enabled traffic control auto recover time: 0 minutes port thres broadcast multicas...

  • Page 613

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 609 des-3200-28p:admin#config traffic control log state enable command: config traffic control log state enable success. Des-3200-28p:admin# 72-5 config traffic control auto_recover_time description this command is use...

  • Page 615

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 611 parameters - (optional) specify a range of ports to be displayed. If no parameter is specified, the system will display all current traffic segmentation tables. Restrictions none. Example to display traffic segment...

  • Page 617

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 613 des-3200-28p:admin#create trusted_host 10.48.74.121 command: create trusted_host 10.48.74.121 success. Des-3200-28p:admin# 74-2 delete trusted_host description this command is used to delete a trusted host entry ma...

  • Page 618

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 614 parameters - the ip address of the trusted host. Network - the network address of the trusted network. The form of network address is xxx.Xxx.Xxx.Xxx/y. - enter the network address used here. Add - add interfaces f...

  • Page 619

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 615 des-3200-28p:admin#show trusted_host command: show trusted_host management stations ip address access interface ---------------------------------------------------------------- 10.48.74.121 snmp telnet ssh http htt...

  • Page 620: Chapter 75

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 616 chapter 75 unicast routing command list create iproute [default] {} delete iproute [default] show iproute {} {static} 75-1 create iproute description this command is used to create an ip static route. Format create...

  • Page 621

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 617 parameters default - deletes an ip default route (0.0.0.0/0). Restrictions only administrator, operator and power-user level users can issue this command. Example to delete an ip default route: des-3200-28p:admin#d...

  • Page 622

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 618 des-3200-28p:admin#show iproute command: show iproute routing table ip address/netmask gateway interface cost protocol ------------------ --------------- ------------ -------- -------- 10.1.1.0/24 0.0.0.0 system 1 ...

  • Page 624

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 620 parameters none. Restrictions only administrator-level users can issue this command. Example to disable the vlan trunk: des-3200-28p:admin#disable vlan_trunk command: disable vlan_trunk success. Des-3200-28p:admin#...

  • Page 625

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 621 parameters - enter a list of ports used for the configuration here. All - specify that all the ports will be used for this configuration. State - specify that the port is a vlan trunk port or not. Enable - specify ...

  • Page 626

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 622 des-3200-28p:admin#config vlan_trunk ports 7 state disable command: config vlan_trunk ports 7 state disable success. Des-3200-28p:admin# port 6, 7 have the same vlan configuration before enabling vlan trunk. Port 6...

  • Page 627

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 623 des-3200-28p:admin#show vlan_trunk command: show vlan_trunk vlan trunk global setting ---------------------------- vlan trunk status : disabled vlan trunk member ports : 1-5 des-3200-28p:admin# the following exampl...

  • Page 628: Chapter 77

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 624 chapter 77 password recovery command list enable password_recovery disable password_recovery show password_recovery 77-1 enable password_recovery description this command is used to enable the password recovery mod...

  • Page 629

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 625 parameters none. Restrictions only administrator-level users can issue this command. Example to disable the password recovery mode: des-3200-28p:admin#disable password_recovery command: disable password_recovery su...

  • Page 630: Appendix A

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 626 appendix a password recovery procedure this chapter describes the procedure for resetting passwords on d-link switches. Authenticating any user who tries to access networks is necessary and important. The basic aut...

  • Page 631

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 627 command parameters reset account the reset account command deletes all the previously created accounts. Reset password {} the reset password command resets the password of the specified user. If a username is not s...

  • Page 632: Appendix B

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 628 appendix b system log entries the following table lists all possible entries and their corresponding meanings that will appear in the system log of this switch. Category event description log information severity s...

  • Page 633

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 629 unsuccessful unsuccessful! (username: , ip: ) firmware successfully uploaded firmware successfully uploaded by console (username: , ip: ) informational firmware upload was unsuccessful firmware upload by console wa...

  • Page 634

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 630 new root bridge cist region new root bridge selected ( mac: priority :) informational new root bridge msti region new root bridge selected (instance:, mac: priority :) informational new root bridge new root bridge ...

  • Page 635

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 631 authentication policy is disabled authentication policy is disabled (module: aaa) informational successful login through console authenticated by aaa local method successful login through console authenticated by a...

  • Page 636

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 632 login failed through console due to aaa server timeout or improper configuration login failed through console due to aaa server timeout or improper configuration (username: ) warning successful login through web au...

  • Page 637

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 633 successful enable admin through web(ssl) authenticated by aaa local_enable method successful enable admin through web(ssl) from authenticated by aaa local_enable method (username: , ) informational enable admin fai...

  • Page 638

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 634 web due to aaa server timeout or improper configuration due to aaa server timeout or improper configuration (username: ) successful enable admin through web(ssl) authenticated by aaa server successful enable admin ...

  • Page 639

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 635 creating impb entry failed due to no acl rule available creating impb entry failed due to no acl rule being available(ip:, mac: , port ) warning ip and password changed ip address change activity management ip addr...

  • Page 640

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 636 802.1x authentication failure 802.1x authentication failure from (username: , port: , mac: ) warning 802.1x authentication success 802.1x authentication success [for ] from (username: , port: , mac: ) informational...

  • Page 641

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 637 depended) bpdu protection bpdu attack happened port enter bpdu under protection state (mode: drop ) informational bpdu attack happened port enter bpdu under protection state (mode: block) informational bpdu attack ...

  • Page 642: Appendix C

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 638 appendix c trap log entries this table lists the trap logs found on the switch. Trap name variable bind format mib name coldstart none v1/v2 snmpv2-mib warmstart none v1/v2 snmpv2-mib linkdown ifindex v1/v2 if-mib ...

  • Page 643

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 639 swfanrecover swfanunitindex swfanid v2 equipment.Mib swhightemperature swtemperatureunitindex swtemperaturecurrent v2 equipment.Mib swhightemperaturerecover swtemperatureunitindex swtemperaturecurrent v2 equipment....

  • Page 644

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 640 swvlanloopdetectvid swddmalarmtrap swddmport swddmthresholdtype swddmthresholdexceedtype v2 ddm.Mib swddmwarningtrap swddmport swddmthresholdtype swddmthresholdexceedtype v2 ddm.Mib swbpduprotectionunderattackingtr...

  • Page 645: Appendix D

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 641 appendix d radius attributes assignment the radius attributes assignment on the des-3200 is used in the following modules: 802.1x (port-based and host-based), and mac-based access control. The description that foll...

  • Page 646

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 642 priority of the port. If the user has configured the 802.1p priority attribute of the radius server (for example, priority 7) and the 802.1x, or mac-based authentication is successful, the device will assign the 80...

  • Page 647

    Xstack ® des-3200 series layer 2 managed fast ethernet switch cli reference guide 643 access_profile profile_id 1 add access_id auto_assign ethernet vlan_id 1 port all deny ; if the user has configured the acl attribute of the radius server (for example, acl profile: create access_profile profile_id...