Summary of 680 TVL
Page 2: Ir Vandal Dome Camera
2 ir vandal dome camera 사용 설명서 용 서 dic-7030dv 680tvl manual.
Page 3
3 the lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point wi...
Page 4
4 the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Information - this equipment has been tested and found to comply with limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are d...
Page 5
5 it could cause an electric shock. Do not disassemble the camera. It may result in fire, electric shock or other hazards. Do not use the camera close to a gas or oil leak. It may result in fire or other hazards. 1.Features --------------------------------- 6 2. Cable connection & osd control ------...
Page 6
6.
Page 7
■ sony 1/3" 480k/570k-effective pixel ex-view had ccd ii minimum resolution 0.1 lux (f1.2, 50 ire) ■ high resolution: more than 680 tv lines this camera has realized high resolution of 680 tv lines using the top-notch full digital image processing, 12 bit a/d serial signal processing and special alg...
Page 8
8 1) cable connection ( dc12v type ) (dual type dc12/ac24v) 2) osd control ① 3axis bracket - please loosen screws and fix tilted and panned position. ③ lens : vari-focal auto iris lens ( 2.8mm ~ 12.0mm / f1.2 ) with icr osd pcb - setup button : used for the menu display. This button can be used to c...
Page 9
9 • please press the setup button to set osd menu. The setup menu is displayed like under the picture on the monitor. • if it has been selected. You may move up/down to use another function by up/down buttons and change the status by pressing left/right buttons. • after finishing all desired setting...
Page 10
10 •auto (high luminance) - auto iris select this to control the shutter speed automatically. -shut+auto iris select ae control on the medium and high brightness side -brightness select the high and medium brightness side reference ( low luminance) -agc select ae control on the low-brightness side -...
Page 11
11 • atw - speed adjusts the pull-in speed atw - delay cnt sets the time-based hysteresis of atw - atw frame sets the pull-in frame magnification - enviroment sets the pull-in frame(indoor/outdoor)of atw • user1 - b-gain used for operating the b gain in the wb fixed gain mode -r-gain used for operat...
Page 12
12 backlight • off backlight compensation off • blc backlight compensation on • hlc high light compensation on pict adjust •mirror: sets the horizontal flip for display output •brightness: sets the screen brightness •contrast: sets the screen contrast •sharpness: sets the screen sharpness •hue: adju...
Page 13
13 •luminance sets the extent of the luminance compression (low/mid/high) •contrast sets the extent of the contrast enhancement (low/middle/mid/midhigh/high) motion det •detect sense: sets the motion detection sensitivity •block disp off: controls the on/off status of the motion detection block disp...
Page 14
14 privacy •area sel: selects the mask frame to be adjusted •top: sets the top side of the mask frame selected by the area sel parameter •bottom: sets the bottom side of the mask frame selected by the area sel parameter. •left: sets the left side of the mask frame selected by the area sel parameter....
Page 15
15 set the threshold for identifying the day status from the night status. • b/w -burst burst signal off enable, burst signal on • color the picture is always displayed in color. Nr the function is used to set the noise reduction -nr mode off y:y filter on c: filter on y/c:y and c filters on -y leve...
Page 16
16 • ↑↓→ ← the camera id cursor moves • clr the character selected by the camera id cursor is cleared • pos the display switches to the camera id display position setting screen sync • int internal mode • ll line lock mode language select the language in which to display the internal osd menu. Engli...
Page 17
17 if you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. • nothing appears on the screen. - check that the power cord and line connection between the camera and monitor are fixed properly. ...
Page 18
18 5. Dimensions.
Page 19: 6. Specifications
19 ▪ general signal system ntsc pal image sensor sony 1/3" 480k/570k-effective ex-view had ccd Ⅱ total pixels 1020(h) × 596(v) 1020(h) × 596(v) effective pixels 976(h) × 494(v) 976(h) × 582(v) resolution 680 tv lines syns. Inter. H/v 15.734/ 59.94hz 15.625k/50hz min. Illumination(f1.2) ir on : 0 lux...