- DL manuals
- D.T.Systems
- Pet Care Product
- Micro-iDT PLUS Series
- Owner's Manual
D.T.Systems Micro-iDT PLUS Series Owner's Manual
Summary of Micro-iDT PLUS Series
Page 1
Super trainer super trainer tm tm micro-idt™ plus series electronic dog trainer owner’s manual • micro-idt™ plus (one dog trainer with add-on capability).
Page 2
2.
Page 3: Table of Contents
Table of contents • table of contents .................................. 3 • introduction............................................ 4 • package contents ................................. 5 • model features...................................... 5 • parts & functions ...................................
Page 4: Introduction
4 congratulations and thank you for purchasing our micro-idt™ plus training collar with add-on capability. It offers the maxx-range™ internal antenna system, the industry’s only internally woven antenna in the collar. With up to a 900 yard range, they are perfect for use around the house and versati...
Page 5: Package Contents
Package contents • transmitter* • collar receiver • rechargeable batteries for the collar (already in- stalled in collar unit) • battery charger • splitter/adaptor charging cable • test light • owner’s manual *9-volt transmitter battery not included model features • digital technology • up to 900 ya...
Page 6: Transmitter
6 transmitter parts & functions intensity selection dial collar selecting switch antenna led indicator light vibration button magnet indicator (red mark) model number momentary “nick” stimulation button continuous stimulation button battery cover (back side).
Page 7: Parts & Functions
Parts & functions intensity selection dial the intensity selection dial can be set from level 1 to level 16 to find the exact stimulation level for your dog (see page 16). Transmitter antenna be sure to check that the antenna is securely fas- tened to the transmitter before each use. Hand- tightened...
Page 8: Parts & Functions
8 parts & functions collar selecting switch switching between collar units can be controlled by moving the toggle selection switch to the desired unit. Remote training buttons pressing the “nick” button will make the collar give a momentary, or ‘nick’ stimulation. Pressing the “cont” button gives a ...
Page 9: Red Mark On The Collar Unit
Red mark on the collar unit the red mark indicates the location of the magnet switch in the receiver. To turn the receiver on/off, touch and hold the red mark with the magnet indicator (red mark) on the side of the transmitter until the led light on the collar unit starts to flash. Parts & functions...
Page 10: Contacts
10 contacts contacts should fit snugly against the dog’s neck to ensure good contact with the skin. For more information on the proper fit of the collar, see page 15. Parts & functions battery charging receptacles the battery charging receptacles are located on the side of the collar receiver. After...
Page 11: Battery Charging Procedure
Micro-idt™ plus seriescollars are equipped with rechargeable nickel metal hydride (nimh) batteries, which are not memory sensitive and do not require depletion before recharging. Although batteries come partially charged from the factory, it is recommended that they are given a full charge (about 12...
Page 12: Turning On and Off
12 turning on and off the transmitter is always in a permanent sleep state. It is only on when a button is being pressed and does not need to be turned off by the user. Turning the collar unit on: hold the red mark (magnet indicator) on the left side of the transmitter directly against the red mark ...
Page 13: Testing
To test the electronic stimulation: 1. Place the tester firmly on the contacts of the collar receiver. 2. Set the intensity (note - an intensity level setting of 4 or less might not be enough to light the tester). 3. Push the ‘nick’ or ‘cont’ button. 4. The tester light will quickly flash once when ...
Page 14: Programming
14 programming when adding an “add-on” collar, the collar will need to be programmed to the transmitter. If your current collar unit is not responding to the transmitter, it may also need to be reprogrammed to the transmitter. 1. Select the desired collar selecting switch position on the transmitter...
Page 15: Properly Fitting The Collar
Note: proper collar tightness and position are very important to insure safe and consistent collar use. All electronic collars need to be very snug around the dog’s neck to work properly. They must be just tight enough to allow the “contacts” or electrodes to make good contact on your dog’s skin. If...
Page 16: Setting The Intensity Level
16 it is very important to set the correct intensity level on your micro-idt plus training system before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. 1. Place the intensity selection dial so that the system is set on level 1. 2. Turn ...
Page 17: Maintenance
Maintenance it is very important to periodically clean your micro- idt™ plus seriessystems for maximum performance. Regular cleaning will also lengthen the life of your unit. • clean the micro-idt™ plus series collar box with lukewarm water and a mild anti-bacterial soap. • take care to thoroughly c...
Page 18: Important Safety Notes
18 important safety notes • before training, your dog should be examined by a veterinarian to assure that your dog is in good health. • never leave your dog unattended with the unit on. Since no electronic device is perfect, there is a very slight possibility that your dog may receive an unintention...
Page 19: Warranty
Warranty all micro-idt™ plus trainer systems have a one year parts and labor warranty effective from the original date of purchase. A copy of the original sales receipt is required to validate the date of purchase. The micro-idt™ plus trainer has been made with state of the art equipment. Any fine a...
Page 20
20 2872 walnut hill lane dallas, texas 75229 tel: (214) 350-9446, (888) 588-8364 fax: (214) 350-7847 website: www.Dtsystems.Com e-mail: customerservice@dtsystems.Com 1-idt plus 2010.05.28 printed in korea.